Mega 651 AGP Video Card Init Problem

Hello all, I've got a great Mega 651 that I've used off and on for a couple of years for "light" office work. I've been trying to install a Radeon 9600 AGP card with not much success. On the initial install the card had output and I installed the catalyst drivers. Upon reboot the card no longer functions. I then removed the card, and installed agp121 I saw from a different post, reinstalled card and all was well until I shut down and restarted then the card was not working again and only the onboard was. Any thoughts?

I installed the correct Mhz cpu a 2.66 533 and the system is running stable, so I reinstalled the graphics card, and all was well for about 1 hour, then my monitor displayed a "no signal" and the system reverted back to the onboard VGA. Anyone experienced anything like this before? I'm wondering if the graphics card is bad (bought it used). Is there any hardware way to disable the onboard VGA (like jumper or something)? Thanks

Similar Messages

AGP video card installation problem. Help!!!

How in the WORLD am I going to get my AGP video card installed??? I can't get it close to the AGP slot before everything is in a bind. The power cable bundle sticks out too far, and it looks like the optical drive hangs out over the AGP slot. What did you folks do??? Please help soon. If I can't get my AIW9700Pro installed, I might as well send it back to where I bought it.
Glendor...

To get mine in I cut the ties further down the board so that I could move stuff around easier.
I was able to put 1/2 of the cables coming out of the psu over the card, the other 1/2 pressed flat against the PSU. That way it JUST fit.
Very tight squeese but Fits ok when secured.
Once the card is in the slot there is more room above the card to push the cables so it may work if you remove the PSU, fit the card then refit the PSU with the cables just above the AGP card.

K8T Neo-V, problems w/ savage agp video card (Stealth III S540)

Hi all
I have a K8T Neo-V mobo, 512 MB Kingston memory and a Stealth III S540 agp video card. The problem is that when I play any kind of video in my linux box it freezes completely the system, same thing with Windows Xp SP2. When i start Soldier of Fortune it hangs up the system. The agp card is quiet old, i know, could be this a problem with some BIOS setup like 'aperture size' and speed, and so on? Don't know about what this options means ???, maybe that's the source of the problem, who can give me some piece of advice about this, please. I'm considering getting a newer and faster agp card, but not in the near future.
Thank you

I am suprised a card that old even works as I thought those were for the original AGP setup that had different voltages.
I would really recommend grabing a newer card up and if you are just looking for a simple display maybe you can still find an old Ti4200 or such.

USB Ports and AGP Video Card on same IRQ

I've got a tough one. I have 6 USB ports. Call them 1,2,3,4,5,6. Ports 1 and 2 work fine with my new USB 2.0 80GB External Harddrive. This pair of ports 1 and 2 are direct into motherboard.
However system crashes when I plug USB 2.0 External Drive into ports 3,4,5,6. These are Dports with cables that plug into the MB. One of these Dports has the four error lights which are all green. Western Digital has cautioned against sharing this drive with other IRQs. Says that the video card and the WD harddrive require dedicated IRQs...but I have no control of how W XP assigns them.
Ports #3-6 work fine with mouse, scanner, and printer etc. However they fail when trying to use WD External Hardrive.
I also checked IRQ settings and IRQ 16 is used for a USB Port and for my MSI AGP video card. I believe this conflict is the cause of the problem.
So help..how do I fix this dilemma?
I have Windows XP and see no way to change IRQs.
BIOS does not even show IRQ as a choice..only 1-15. Also BIOS is latests version for my MSI 845G Max L MS-6580 mother Board. USB drivers are all Intel. Video Card Is MSI AGP MS-8878 G4Ti/MX 420 w TV out. Bios and Drivers are current.
How can I run the USB 2.0 External Harddrive in Ports 3-6?

I did load new Intel INF Drivers and AGP drivers yesterday.
No luck USB Ports 3-6 still fail with External Hard Drive.
I'm not clear on how to turn back on AICP or ACIP. BIOS?
Also not IRQs 16-23 are listed with active devices on the Device Manager
16 has a USB Controller at 24c2
16 also has AGP video card
17 has Audio '97
17 also has Fast Eternet.
18 has USB Controller at 24c7
19 has USB Controller at 24c4
23 has PCI to USB Interface.
Port 3-6 do work fine with mouse, dig cam, Scanner, printer. These ports only fail with External Harddrive plugged in. Ports 1and2 work fine with external HD??
So question is how do I check on the IRQ ports using AIPC or APIC...or whatever the name is...thanks folks.

Startup error with AGP video cards

I have a WInME machine that gives me errors on windows start-up that ask me
to hit ctrl-enter to clear and states that the client did not remain
resident. These only occur when I have an AGP video card installed. I do
have a PCI video card but would like to use it in a different machine. Has
anyone run across anything like this?
Thanks,
Craig Yager

I had tried that to no avail. I had also tried uninstalling the video
drivers earlier using the always reliable add/remove programs and got a
message that they had already been uninstalled. Just for grins, I tried it
again a few minutes ago (since it showed back up in the list of programs)
and it uninstalled for real that time. So I restarted, got no novell client
error msgs, re-installed video drivers, and got no error messages on
re-start! So I guess there was some sort of corruption in the video driver
that was causing this whole mess. Anyway, all's well now..thanks for your
help Barry!
"Barry Schnur" <[email protected]> wrote in message
news:[email protected]..
>I guess what you might try first is to uninstall the client (making sure
> you have the software on the system to reinstall it first).
>
> Then see if you get error messages on start up.
>
>
> --
> Barry Schnur
> Novell Support Connection Volunteer Sysop

ATI Radeon 9600 Pro 256MB 8x Dual (DVI/DVI) (AGP) Video Card for PC/Mac

We want to be able to use our 30" cinema display from the G4 and was advised in a previous discussion to buy the ATI Radeon 9600 Pro 256MB 8x Dual (DVI/DVI) (AGP) Video Card for PC/Mac. It doesn't seem to be available anywhere. Does anybody know of an alternate video card that's currently available that will get us there? (We had the display running from a G5 that quit / logic board failure).
Many thanks,
Philip

The Nvidia 7800GS is a flashed card, runs a 30" with ease.
BruinMacs on Ebay is a great place to get one, you support the guy who wrote the original ROM for these.
He doesn't seem to have any for sale right now, but if you email him, maybe he will list one.
There are also flashed X800s that work on your MDD and can run a 30". They are pricey but will offer dual DVI while the 7800GS is single DVI with VGA for second display.
There are also flashed 6600GT AGP cards which will work, but harder to find.
Any of the above 3 will run circles around a 9600.

Will this card work? - Nvidia Geforce 6800 ULTRA 256MB VRAM AGP Video Card

I posted a question about getting the maximum resolution from an Apple 30 inch Cinema Display and another card, which didn't work.
The replies were fast here in the forum and quite correct.
My next question is regarding the Nvidia Geforce 6800 ULTRA 256MB VRAM AGP Video Card.
I have an AGP card with an ATi Radeon 9600 Pro card that can't power the 30 inch because it's only 64MB and no DVI output.
I'm wondering whether this card will give me the maximum resolution?
Thanks again.

Hi Japamac-
Thanks for the quick reply.
My System Profiler indicates a ATI Radeon 9600 Pro, but it doesn't have the Dual Link since this is an older G5 with only 64MB of VRAM.
The GeForce 6800 is a refurb, but is Mac compatible.
I'm hoping that it will work, but since it won't be returnable, I don't want to spend the money needlessly.
I did order another card that the Apple support suggested should be compatible, but turned out that they sent me the PC version.
I've spoken to Apple as well and get conflicting info.
It boils down to the fact that this is a G5 with a late 2004 date.
It is fast enough for me and my only hang up is that I'm only getting 12980X800 resolution.
I'm not using it for gaming or graphics processing.
HTH.

Mega 651 TV-Out card problem

Hi freakz,
i have a Mega 651 with the original MSI TV-OUT card, but I don´t get any picture onto my TV.
I´ve already reinstalled the diasplay drivers. In windows I can´t find any configuration for the TV-out.
In the bios I´ve tested all settings.
My TV is switched on, so the card should recognize it.
Does anybody have the same card working? When does the picture appear on the TV screen? at the bios booting or at the Windows screen?
Which resolutions should I choose? I´ve tried 800x600 and 1024&768. Nothing.
Perhaps the card is broken, but first I will try everything so I can get shure.
Please... Can anybody help me with my problem or give me tips?
Thanx
Alex

Hi,
first of all, be sure I have tried everything, other cables (even shorter ones), ....
It´s the add on card for the Mega 651 which has a composite and a S-video plug.
I work with the chinch composite output.
In the bios I can choose between TV, CRT, or both.
Even if I only connect the TV, nothing appears on it.
Should I see the POST screen on the TV, or first when the display driver has been initialised?
Alex (still no pictures )

What AGP video cards work with the MEGA PC

Hi,
I am a newbie to this forum and a new owner of a Mega PC651. I will be configuing it with the following:
512 MB DDR 2100 RAM
Celeron 2.4Ghz CPU
Digital Research Technologies DVD+-RW/+-R
I want to play 3D games like C&C Generals with the system but am afraid that the SIS651 will not support them.
I have a ATI 9700 All-in-wonder Card in my son's computer but am concerned about heat generation in the Mega PC after reading several reviews. Also, I think that he will be very angry if I steal his card.
Can anyone recommend a moderately priced Video card MSI or other that will fit and will not cause any heating problems?
Thanks,
Charlie G

Windows XP supports up to AGP 8x.
I have a 9600 pro at the moment. I don't think that VGA silencer will work - if it takes up the PCI slot, then there will be nowhere for the cooler to draw air from because it will be pressed up against the case.
I am currently running my 9600 pro without any additional cooling and it seems to be doing ok. I did have a unit somewhat like this:
http://www.frozencpu.com/cgi-bin/frozencpu/slf-01.html
It definately helped the cooling but the noise began to get to me. I recently sorted out my CPU cooling problems and so the main source of noise was my system exhaust above. I have taken it out and have been playing several high graphics games with no problems yet.
As for only supporting up to 4x, the 9600 pro will not be dragged back much. When it gets to the point that games require more than 4x speed to pass full detail for a decent framerate, the 9600 pro will start to struggle anyway. You will have a slight performance decrease, but nothing that will turn a game from being playable to un-playable. I would have bought a better card but the 4x speed would limit the cards actual power so there wouldn't have been any point.

Mega 180 - Install Video Card or Install Video Driver

I just spent 6 hours at a customer's house trying to fix the Mega 180 I built for her.
As I stated in a previous thread, the machine was working fine and then she experienced the BLACK SCREEN OF DEATH. This is when your machine POSTS, loads Windows and just before Windows starts, the monitor goes dead. Windows still loads and if you remember where icons are on the desktop, you can click them and stuff happens. The monitor just stops getting a signal. However, if you hold down F8 during boot and chose VGA mode, you can use Windows in VGA mode. The monitor being used is a Sony Multiscan200ES.
Once in Windows, if you look under device manager, you'll see a listing of Unknown and under that it lists nVidia GeForce4 MX Integrated CPU.
So, I've tried the following fixes:
1) Uninstalled all chipset & viideo drivers, reboot, reinstall chipset drivers, reboot, reinstall video driver, reboot. BLACK SCREEN OF DEATH.
2) Uninstall video driver, reboot. Windows starts under the generic driver. I install the video driver, reboot, BLACK SCREEN OF DEATH.
3) Figuring there had to be an easier solution to this problem, I installed an ATI Radeon 8500 card that I had laying around (I know this card works) figuring that I'll just sidestep the whole video driver issue by not using the onboard video. Things just aren't that easy because after I installed the card the machine won't even POST. It turns on but nothing happens. ARRRR!!! I try reseating the card, nope - nothing. I take the card out and use the onboard graphics to make sure everything is ok in BIOS. I read that if the BIOS detects an AGP card it will automatically disable the onboard graphics but it doesn't seem like that's happening. So I look around BIOS and there is no way to disable the onboard graphics. I have it set to boot AGP first, etc. and nothing works.
I guess the last thing I can do is reformat the drive, reinstall windows, and reinstall everything else. But I don't want to do this because the machine is all set up, been used for a while, and it takes so long to reinstall everything.
My question is this. How can I either reinstall the video driver so it works or how can I install a video card so it works? Ideas???

Quote
I'm going to hunt over at nVidia's website to see if they have a cleaner utility (ATI does for its Radeon drivers - rids the system of every last trace).
nVidia don't need a cleaner utility cos their software is better written!
stab in the dark - the vga lead is connected to PRIMARY vga port?
go to add/remove programs and Remove "Nvidia Display Driver" in Safe mode
restart your computer and it should boot into VGA mode, and prompt with Found New Hardware. cancel this.
the nvidia software will leave the install stuff on your computer, usually in C:\NVIDIA. browse to here and find and run the setup.exe to reinstall the software.
if its been working before, then its probably not a memory issue - it might also be worth making sure the latest nforce drivers (3.13) are installed too.
oh and customers usually WON'T admit to messing around to stuff they shouldn't - in my experience anyway!!

Will X1650XT 512MB AGP Video Card work with 865PE MS-6728?

Hi,
My video card is fried, so I'm thinking of upgrading to a HIS X1650XT AGP 512MB video card. I read somewhere that some motherboards have issues with 512MB video cards. Is this true? I can't find anymore info on whether this motherboard will support this video card.
http://www.hisdigital.com/html/product_ov.php?id=276&view=yes
Anyone have any input?
Thanks!

No need to get hostile, I didn't say you were an idiot. Though continuing to make uninformed statements might get you there....
Quote
The video cards need at least 30A to make the card run properly. That's pretty damn easy to understand how the last PSU was the problem.
Actually, it doesn't. The 30A figure cited by the manufacturer is a worse case scenario for +12V needs of the entire system + the graphics card. The X1650XT doesn't even need an auxillary PCI Express power connector and can be powered entirely through the PCI Express slot, which supports a maximum of 75W.
If you need further proof of this, for CrossFire setups the manufacturer cites a figure of 38A on the +12V rail. If one card requires 30A, how could two cards require only 8A (96W) more than one? The same requirements are stated for X1950XT (30A single and 38A Crossfire), so its a highly generic target that attempts to account for an entire range of power supply rating methods and total system power demands.
Here are total power consumption measurements of whole systems used in various X1650XT tests:
Intel Core 2 Duo Extreme X6800 @ 2.93 GHz
Corsair TWIN2X2048-8500C4
Western Digital 150GB 10K Raptor
Sound Blaster Audigy 2 Value
AMD ATI Radeon X1650 XT
Total system power under 3D load = 206 Watts MAX
AMD Athlon 64 X2 4800+
2GB Crucial PC-4000
Western Digital 74GB 10K Raptor
AMD ATI Radeon X1650 XT
Total system power under 3D load = 192 Watts MAX (only 66W higher for 2 x X1650XT in CrossFire)
Intel Core 2 Duo Extreme X6800 (2.93GHz/4MB)
Seagate 7200.7 160GB SATA
Corsair XMS2 DDR2-800 4-4-4-12 (1GB x 2)
AMD ATI Radeon X1650 XT
Total system power under 3D load = 182 Watts MAX
Those are figures for TOTAL system power needs, not the graphics card itself. Here are figures just for the X1650XT from X-bit Labs:
55.2 Watts @ full load
That's not more than 5A MAX from the +12V rail. Even assuming a 20% VRM loss, gets us to around 6A MAX.
As anyone can plainly see, the manufacturer's stated requirement of 30A is a hugely overinflated number to help people avoid purchasing a power supply like this because they are looking only at hugely inflated total power.
Given that your X1650XT could not possibly require more than 6A of 12V+ power, and high-end systems using overclocked Dual Core Extreme don't even consume more than around 250W TOTAL (all components combined, factoring VRM loss), the evidence is now overwhelming and beyond dispute that your previous power supply was more than adequate and that inadequate power was never the cause of your problem. It could have been defective, but that isn't the same as having inadequate power.
Questions?

ATI RADEON 9600 PRO 256 MB AGP Video Card

I just upgraded my G5's video card from 128 BIT to 256 BIT. I am using a Samsung 42" TV as my display and connecting it using the XtremeMac XtremeHD HDMI to DVI Cable.
I only get a resolution setting of: 1360 X 768
I have a few questions:
1. Why is the resolution so low? When I used my 128 Video Card, it was at that setting and I thought if I upgraded to the 256, my resolution would go higher.
2. When I used to play a .mkv 720 movie with my 128 BIT card with VLC player, during the movie at some points the movie would freeze and the audio would still play and then after a while the movie would continue. This still happens with the 256 BIT card, why?
I thought upgrading the card would improve my video abilities with VLC player and resolution. Anyone can help me out here?
Thanks!

You have upgraded from 128 Megs of VRAM to 256 Megs of VRAM. Sadly, it is still a memory bus of 128 bits, hence the poor performance.
Your resolution stayed the same because that is all the dots there are on your older TV. (Native Resolution)
The 9600 was never a speed demon.
You should check out Barefeats.com for speed comparisons.

Video Card install problems

I have been having problems getting past the video card setup. I have a ATI Rage Pro 8m/b, whenever I select it as an option and test it (or any other card in the family like xpert@play ) the xserver reports it could not find a mach64 controller. The only way I can get the install to complete is to use the generic 64x480 16 colors driver. Now that it is installed and semi-working, could someone let me know how I can change the driver after the O/S is installed. I have not patched the O/S yet.
-Chris

If "dtlogin" is running, stop it with "Options" ->
"Command line login". Login on the text console
as user "root", then run "kdmconfig" to configure
the video card.
When you logout from the text console, dtlogin is
restarted automatically with the new settings after
10-15 seconds.

Any video card driver problem referenced for MBP17" ?

Hi.
I have been spending hours trying to install XP on the bootcamp partition of my new MBP 17". Everything is fine except that Windows freezes after a while, and I get an error message stating that the graphic accelerator has been disabled.
I have all latest versions of Bootcamp, updates XP as well, tried re-installing different drivers for the ATI Radeon 1600 (Mac, ATI or third-party pilots). Nothing. I cannot use my XP install at all.
Any referenced problem on the video card of MPB 17" and XP ?
I am lost.
One information: I run XP on a FAT32 partition.
Many thanks in advance if someone can help me.
Regards,
Pierre

Changing the frequency of the video card with ATI Tools was the answer. Thanks to all for your help.

AGP Video card upgrade

I fear the answer will cost me $400, but here we go:
I have a dual processor Power Mac G5 tower.
There's an AGP 9800 128mb video card in there I want to upgrade.
I have an ATI X800 AGP 256mb card from a PC that's not being used anymore. I can install the card and use a Y connector off the optical drive to get power to the card, but when I boot the system I get no video.
Just as a test, I removed the card and booted the mac with no video card, it acted the same as when the X800 was in: System appears to be booting, no error beeps or anything, I just don't see anything on the screen.
I fear the answer is "Buy a Mac Edition card" but really, the only feasible option is the X800XT MacEd which is a ~$400 card after shipping costs.
Now, is there a bios upgrade that I need to make the card work? Do I need to reset the PRAM to make it be recognized? Does anyone know a card with 256mb RAM that will outperform the 9800 I have now, but not cost me an arm and a leg?
I only run two applications on this computer: Firefox and World of Warcraft. I guess if this card won't work, I'll just ebay it and spend $100 on another gig of ram and wait for the X800 video cards price to drop.
Any help the can be offered, I greatly appreciate it. Thank you in advance.
G5 Power Mac Mac OS X (10.4.6)

Check with Mike over at Accelerate Your Mac, he should know how to flash that card to get it to work with a Mac.
It' probably best to sell it and buy a Mac card, than take a chance.
The X800xt is your best choice and I would choose soon because AMD bought ATI and the future is a little uncertain. Certainly AGP cards will be running out and getting more powerful ones even harder.
You should also run the latest ATI updater before installing the new card.
also
http://www.barefeats.com/radx850.html

Mega 651 AGP Video Card Init Problem

Similar Messages

Maybe you are looking for