Memory for Km266

Can I install PC2700 and PC2100 DDR modules on this board.I have 1 PC2100 128mb and found PC2700 256mb module to add to it can it be done?

they will both work at 266 if they will work at all
but only way to find out is to try

Similar Messages

Can i upgrade my memory for my hp dv7-6c60us laptop to 16G?

i was just wondering if i can upgrade my ramm to 8g-16g ... if its even possible..

Hi:
Below is the link to the service manual for your notebook.
http://h10032.www1.hp.com/ctg/Manual/c03099448.pdf
Chapter one page 5 gives the supported memory allowances.
Because you have an Intel based chipset and processor you can install 2 x 8 GB of memory for a total of 16 GB.
Had you had an AMD based chipset and processor, the maximum would have been limited to 8 GB.
Paul

Ive deleted contacts from my contacts list but they still pop up when i go to text and type in the name of a current contact. . How can i delete them off my phones memory for good?

Ive deleted contacts from my contacts list but they still pop up when i go to text and type in the name of a current contact. . How can i delete them off my phones memory for good? iPhone 4S

At the present time, the only way to clear that is to restore the phone as new. Perhaps a future iOS update will give us the option to clear that cache.

Memory full.Not enough memory for operation.

To the Report Design Team,
It has been suggested that I post this issue here based on another thread I started: Re: Memory full.Not enough memory for operation.
The template contains a single 24 bit PNG image as a background in the Page Header section, plus 9 image records from a SQL Server image field over 3 pages (3 images per page). The images are all JPG at 3000x2000 (digital camera).
To summarize, we are experiencing three problems.
1. CR2008SP2 Designer issues a Memory Full error when Exporting to PDF.
2. Using a 3rd party PDF Printer (Bullzip PDF) and CR2008SP2 Designer generates a PDF, however, the CR2008SP2 API throws a "Memory full" exception suggesting Designer and API are different (see stack trace in linked message above).
3. With only 3 images on 1 page, CR2008 Designer Export to PDF takes 110 seconds to generate a 24MB PDF while our third party PDF Printer generates the same report in 17 seconds and 580KB.
Edited by: Don Williams on Sep 30, 2009 6:43 AM

The .rpt file size is 14MB with the Data Save option enabled, 12MB without Data Save. Presumably the 12MB file size is because of the 24bit PNG we have as our background.
The Designer executes the report in less than a second and we can scroll through all pages and see the image fields perfectly.
When we Export to PDF, the Designer takes a long time, eventually gets to the 77%, the 7th record and returns "Export report failed" followed by "Memory full". If we export only page 1 of the 3 pages, it also returns a Memory full error. However, when the same report is run with only 1 page, that page exports to PDF but with a ridiculously large size and export time.
The machine has 2GB of physical memory with an 8GB pagefile with Windows 2003 (latest everything). The process runs up to about 1GB before reporting the memory full error.
We've also tried a variety of other suggestions posted in the other thread with no success.
We're happy to provide the RPT file to the Report Team to diagnose the problem. Ultimately, we need to be able to produce a 15 page report with approximately 45 images.
Our preferred scenario is fixing problem 2. The CR Designer seems quite capable of rendering our report and printing it to our third party PDF printer in a timely manner with small size. However, the API reports memory full.
The API resides in a dedicated reporting web service with NO other code except for loading the report, setting parameters and printing. When executing, it uses up to about 1.1GB before reporting the error.
Are there any other suggestions for fixing what we have? Are there known problems with large images in reports? Do we need to lodge a formal support request?
Regards, Grant.
PS. Grr and my message formatting is lost when I edited this message!!!
There is a 1500 character limit and then all formatting is removed to save space. Break you posts into separate entries.
Edited by: grantph on Sep 30, 2009 2:49 AM

How do I get more memory for my Macbook Pro Spring 2010 13-inch with 2.66GHz Intel Core 2 Duo?

How do I get more memory for my Macbook Pro spring 2010 13-inch with 2.66GHz Intel Core 2 Duo. Apple says no memory currently available for that model. I have 4 GB memory and 3.99 used. Help!

macette1976 wrote:
Now I'm confused. This is the one Crucial told me to get:
CT3309356 - 4GB DDR3 PC3-8500 Unbuffered NON-ECC 1.35V 512Meg x 64
$45.99
Also what do you mean that actual memory is 16GB but with Apple it's 8?
When I go to the "About this Mac" it says Memory 4G 1067 MHz DDR3, then when I go to System Report it says
Memory Slot
Bank 0/ DIMM0 2G DDR3 1067 MHZ OK
Bank 1/ DIMM0 2G DDR3 1067 MHZ OK
Sorry I'm clueless. Just don't want to buy something that messes up my machine more than it already is.
The Crucial site appears to have recommended the correct spec 4gB RAM stick for your model. Please note that you will need to remove the existing sticks of RAM to install new, so you will need 2x4gB to get to 8gB.
When your model of computer was designed/built, it was tested with readily available 2x4gB (8gB). After release RAM retailers have tested it with higher amounts, and Apple didn't update their quoted specs.

How to increase the memory for my weblogic server in Jdeveloper 12.1.2.0.0 ?

Hey everyone,
So as my title says, i'm trying to increase the memory for my weblogic server in my windows 7 64 bit machine, with 8GB ram.
The values appear to be: JAVA Memory arguments: -Xms256m -Xmx512m -XX:PermSize=128m -XX:MaxPermSize=512m
I've done some search from this forum and i've added this to my jdev.conf:
AddVMOption -XX:MaxPermSize=1536M (in this one i've only changed the value)
AddVMOption -Xmx1536M
AddVMOption -Xms1536M
And i've changed this: MEM_ARGS="-Xms1024m -Xmx1024m" in my startNodeManager.sh file
I'm still getting the same line in my server but i need to change the values since i'm not getting the server to run my application very well (it gets stucked in loading my databases and graphs) and i think it will continue untill i get a heap exception error.
Any ideas of how to change this?
Regards,
Frederico.

Thanks Alejandro .
I'm going to ask you another question and this one is quite important.
Whenever i run my project a couple of times, i'm not able to retrieve the page, it just gets stuck on loading.
It just stops the loading, like its a really really slow page. I'm not using a lot of rows in my database so i don't take to much memory but it doesn't load and i know everything is fine but i just added some graphs after testing it.
Do you know why?
In the console it says that everything is fine and shows the link for the page but it never loads completely until it gives a error because it does not respond in 600 seconds.
Strange right?

Hello, I have two questions on time capsule I can only have it on my external hd files and free up my internal memory to my mac I can use an external hard drive, in my case a lacie rugged as shared memory for my two computers

Hello, I have two questions on time capsule I can only have it on my external hd files and free up my internal memory to my mac I can use an external hard drive, in my case a lacie rugged as shared memory for my two computers

I have a mackbook pro and an iMac if I buy a time capsule 2tb airport, I can use it with time machine and what would be the best way to use it.
There is no particular setup required for TM.. both computers will create their own backup sparsebundle which is like a virtual disk.. Pondini explains the whole thing if you read the reference I gave you.
and how to use time capsule airport whit other external hd to use my old lacie airport with the new time capsule
Up to you.. you can plug the external drive into the TC and enjoy really slow file transfers or you can plug it into your computer and use it as external drive.. which is faster than the TC.. and TM can include it in the backup.
Again everything is explained in the reference.. you are not reading it.

What are the best UK sites for buying more memory for iMac?

Here is the info on my current imac:
Mac OS X version 10.5.8
Processor: 2.4 GHz Intel Core 2 Duo
Memory: 1 GB 667 MHz DDR2 SDRAM
Model Identifier: iMac7,1
I want to get myself more memory for my type of imac, like 6GB worth. I want to buy from a UK website so I only have to pay minimal postage fees. What are the best sites for this?

Crucial:
http://www.crucial.com/uk/
Lifetime warranty, very reliable, fast service and very helpful.
(No, I don't work for them!)

How do I find out the exact path of each and every file that LabVIEW finds and loads into memory for a given top level vi?

How do I find out the exact path of each and every file that LabVIEW finds and loads into memory for a given top level vi? There is probably a trivial, easy way to get this info, but I have not yet found it! Thanks..

Or if you want to grab all the paths programatically, try the attached VI.
Open the top level that you want all the paths from and close all others, then open the
attached and run it. It will return an array of all the VIs that the VI
in question uses, including vi.lib VIs. You can filter these as well if
you like.
Ed
Message Edited by Ed Dickens on 08-01-2005 07:01 PM
Ed Dickens - Certified LabVIEW Architect - DISTek Integration, Inc. - NI Certified Alliance Partner
Using the Abort button to stop your VI is like using a tree to stop your car. It works, but there may be consequences.
Attachments:
Get all paths.vi ‏29 KB

Scheduled report failure - Not enough memory for operation

Crystal Reports Server XI R2 SP4
SQL Server 2005
Hi,
I have a report that is scheduled. Most of the times it runs successfully, however for one parameter setting I continuously get the following error mesage:
Status: Failed
Printer: The instance is not printed.
External Destination: Copy the instance with default filename to the directory '//10.2.25.24/polling_in'.
Creation Time: 03/04/2009 05:00
Start Time: 03/04/2009 05:00
End Time: 03/04/2009 05:00
Server Used: BWAQTSREP-1.reportjobserver
Error Message: Not enough memory for operation.
Why would this happen, and how can I resolve? I can run the report successfully in Infoview.
Thanks!
Penny

Hi Penny,
do you run the report successfully in the infoview using the same parameter setting?
If it does please try to reschedule the report and monitor (using the task manager) the memory consumption on your windows server.
Please also make sure that there is enough disk space available on both your server and the destination directory ( '//10.2.25.24/polling_in'. )
Regards,
Stratos

Getting " Not enough memory for the operation error " in BOE

Hi,
We are using BOE 11.0.
we try to schedule a new report with multiple database logins for testing in BOE. When we run the report we are getting error like "Not enough memory for the operation error"
The same report has been executed successfully when we run using Crystal reports developer. The report is fectching less than 10K records from all the databases together.
Please let me know which is causing the issue and also let me know is there any limit in the number of databases connecting for a single report.
many thanks in advance for all your help.
Cheers,
Suri ;-)

Hi Sarthan,
Sorry. I'm new to BOE. We know only scheduling the reports creating folders etc. :-)
I've seen one parameter "Maximum Cache Size Allowed (KBytes)" and the value for this parameter is 5000.
If we change it to a big number whether we can solve the issue ? Please suggest.
Cheers,
Suri ;-)

Not enough memory for Data Provider-Error while creating Data Source

Hi,
I am loading data into Master Data_Attribute InfoObject I am getting following error message while creating Data Source under "Proposal" Tab
"Not enough memory for Data Provider"
My Master Data InfoObject having 65 attributes
My CSV file having 15,00000 records
I am using BI 7.0 version
If anybody faced this problem. Please share with me
Thanks.

Hi
Here the problem with the space so plz contact ur BASIS people to increase the spae for particular object.

The merge process could not allocate memory for an operation; your system may be running low on virtual memory. Restart the Merge Agent.

I encountered this problem on our SQL2012 and I have tried different scenarios (see below) to no avail. I have decided to give up and check if someone here has encountered this and resolved it.
One thing I know, it's not a memory issue. Both servers we're using has lots of memory to spare and we monitor the memory as the replication goes through it's steps.
I hope someone can help me on this. Thanks!
The Error:
The merge process could not allocate memory for an operation; your system may be running low on virtual memory. Restart the Merge Agent.
Our Scenario
We're using SQL Server 2012 SP1. All subscriptions are pull based.
We're using direct Merge Replication (not FTP or web sync)
We already have 10 active replications with larger databases. Only 1 has this issue.
Database size is less than 5 GB
Rebuilding the publisher is not an option.
What have I tried?
There is no memory problem --- we have lots to spare
I have tried re-initialization of the database. Same problem.
I tried deleting the database and reinitializing it. Same problem
New snapshot. Same problem.
I tried changing the subscriber server but still same issue.
MCP, MCSD, MCDBA (ANXA)

Here is the result for the sp_configure on our subscriber. We're doing a pull on the server with the issue.
name
minimum
maximum
config_value
run_value
max server memory (MB)
128
2147483647
2147483647
2147483647
In addition, I made a comparison between the working servers and the one with the issue -- there seems to be a difference in the service pack. Publisher has none but the subscriber is operating on SP1. But still strange as only 1 database is affected.
MCP, MCSD, MCDBA (ANXA)

I just downloaded IOS5 and I no longer have enough memory for my music?

I've just downloaded the IOS5 and now not eenough memory for my music? What do i do?

Thanks.The other is 11.5G it claims but I am not sure that is correct. My phone memory is 13.73. If I restore would i lose all my data

Can't use all memory for VM

Hi!
I have Microsoft Hyper-V Server 2012 R2 with 16 Gb RAM. I created two VM with 7162 Mb of fixed memory on each. But i can't start both of them. When i tried start second vm i got out of memory error. Why?
PS C:\Users\Administrator> ( Get-WMIObject Win32_OperatingSystem -ComputerName localhost ).FreePhysicalMemory
8184452
PS C:\Users\Administrator> start-vm oldBSD
start-vm : 'oldBSD' could not initialize. (Virtual machine ID 05EA5A45-601F-4CC0-8770-62B97571D8F8)
Not enough memory in the system to start the virtual machine oldBSD with ram
size 7168 megabytes. (Virtual machine ID 05EA5A45-601F-4CC0-8770-62B97571D8F8)
The server ran out of available memory.
Max memory value for second machine is 5740Mb, but with it i have
PS C:\Users\Administrator> ( Get-WMIObject Win32_OperatingSystem -ComputerName
localhost ).FreePhysicalMemory
2243312
How i can use all memory? My idea is use 7 Gb of memory for each machine and 1.5-2 Gb for host.

Hi maxx-ode,
As far as I know ,to get free memory you still need to subtract the "standby memroy" from the output of the command in your original post .
Please refer to the article "Memory Sizing Guidance for Windows 7" within the link below :
http://msdn.microsoft.com/en-US/library/windows/hardware/dn550976
" Standby List
The Standby list contains unmodified pages that have been removed from process working sets, which effectively makes the Standby list a cache. If a process needs a page that is on the Standby list, the memory manager immediately returns the page to its
working set.
All pages on the Standby list are available for memory allocation requests. If a process requests memory, the memory manager can take a page from the Standby list, initialize it, and allocate it to the calling process. This is called repurposing a page.
Pages on the Standby list are often from recently used files. By keeping these pages on the Standby list, the memory manager reduces the need to read information from the disk. Disk reads
can decrease system responsiveness. "
Please try to use this command to get the "real" free memory of host (in bytes):
(Get-WmiObject Win32_PerfFormattedData_PerfOS_Memory -ComputerName localhost).FreeAndZeroPageListBytes
"Free & Zero Page List Bytes is the amount of physical memory, in bytes, that is assigned to the free and zero page lists. This memory does not contain cached data. It is immediately available for allocation to a process or for system use.
Update: Actually we can allocate some standby RAM to VM , based on my test I can't allocate whole standby RAM .Then I used
RAMMap to check the usage and I found that Mapped file occupied most RAM .For mapped file please refer to following link:
http://blogs.msdn.com/b/khen1234/archive/2006/01/30/519483.aspx
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Memory for Km266

Similar Messages

Maybe you are looking for