Memory ID, CP1518ni

Greetings all, What sort of SODIMM modules does my printer take? I believe it has 144 pin card slots, taken from what I have gathered. I am looking for specifics such as voltage, chip type, etc. NFO I would need to identify it characteristically. Much appreciated, and thanks in advance, ~Michael

Hi ,
There are two types of memory .
1 .ABAP Memory - Export /Import - session dependent
2 .SAP memory - set/get - This is not
Check out this example ot ABAP memory .
http://help.sap.com/saphelp_nw04/helpdata/en/fc/eb3bde358411d1829f0000e829fbfe/content.htm
Please reward if useful.

Similar Messages

"Out of Memory" message from hp color laserjet cp1518ni

While printing an 8.5x11 sheet of bookmarkers (5 on a sheet), the first page prints, the second page comes out blank with a message in the top left hand corner: Out of memory. Turn machine off and then. And It stops printing all together. HELP!!!!!! I have had problem after problem with this machine. I want to get rid of it, but it cost me #$384 and I haven't gotten 1/4 of usage or production.

Answering your questions... MS Pub is the most graphics rich program I use, however I do print quite a bit of full color 8x10 .jpg/.bmp/.tiff/et.al. photos from programs such as Word without any issue. Most of the graphics printed with Pub are Raster graphics if that makes any difference. Notepad/Wordpad, obviously being text based, never create an issue. They always print. In fact whenever I want to conduct a printer test, I send it a notepad text file. When I get the "Low Memory" message, it will NOT print. Period~! Restarting, rebooting, nothing will get it to print a file if the file shows up as too large. Knowing all this, any problematic file which will not print on the CP1518ni, will ALWAYS print fine if I switch the job to our Office Jet Pro L7555~! Back to the memory... if it really is memory, WHY? In light the L7555 works fine. If I need memory, could you provide specifics about the memory? Thanks again, ~Michael

CP1518ni can't print documents bigger than 1 MB

My color laserjet printer (CP1518ni) gives up printing big (> ~1 MB) graphic documents. I see in print spooler (Win XP) computer sends something about 750 KB to the printer, then it stops spooling. AFter a minute or so there is an error message saying document failed to print. THis printer supposed to have 96 MB of RAM so it is not memory issue. I tried different softwares to send printout, but the same problem is there with any software. ANy suggestions, thoughts?

There is no duplex option in the print dialog. From what I've read online the document prints as simplex or duplex depending on what the document properties are and they can't be set in the print dialog.
If this is wrong and there is a way to select duplex from print dialog then I'd be happy to know about it - but all the information out there says even on versions where it is possible to set duplex in the print dialog the document properties override the printer settings.
Like I said I haven't tried it because there is no option there. The only duplex setting I can find is in the document properties which I can't change.

Insufficeint Memory

Hi - using an HP Color LaserJet CP1518ni. Many simply Publisher projects are outputting an error message: Insufficient Memory . Any quick workarounds? This is a recent development -- have been able to print Publisher projects without difficulty in the past. Any help is appreciated! Thanks....

Hi @Micktax,
Welcome to the HP Forums!
I am sorry, but to get your issue more exposure I would suggest posting it, in the commercial forums since this is a commercial product. You can do this at HP Enterprise Business Community.
Hope this helps!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Blank spot in printed page - CP1518ni

My CP1518ni has always worked well, except for one new problem. About one page in five includes a small (c. 1" long, 1/4" wide) blank space on the left side. And a small amount of nearby type is slightly smudged. The appearance is as though a single piece of shredded paper covered that part of the page. But I've searched thoroughly and found nothing in the printer. Is there anything to be done?

Hello, I see that you are getting a blank space on the left side of the page. I will certainly do my best to help you. Make sure the printer is connected directly to a wall outlet. (don't use a power hub or a surge protector) This ensures the printer is receiving full power and may help this situation. Inspect the toner cartridge for damage:
1. Remove the toner cartridge from the product and verify that the sealing tape has been removed.
2. Check the memory chip for damage.
3. Examine the surface of the imaging drum on the bottom of the toner cartridge.
CAUTION: Do not touch the roller (imaging drum) on the bottom of the cartridge. Fingerprints on the imaging drum can cause print-quality problems.
4. If you see any scratches, fingerprints, toner or other damage on the imaging drum, replace the toner.
5. If the imaging drum does not appear to be damaged, rock the toner cartridge gently several times and reinstall it. Print a few pages to see if the problem has resolved. You can calibrate and run a cleaning right from the printer's control panel. Calibrate the printer.
On the printer select the OK button/arrow to main menu system setup/print quality/calibrate color/calibrate now.
Run a cleaning.
On the printer select the OK button/service/cleaning mode/OK.
Print a Diags page.
On the printer select the OK button/main menu report/diagnostics page.
Check the alignment. Please try the steps in this document if you are still having issue. Resolving Print Quality Issues. Are you using Genuine HP Toner?
What are the toner levels?Let me know the results of the Diagnostics page. If you appreciate my efforts, please click the 'Thumbs up' button below.If there is anything else I can help you with, just let me know. Thank You.

I have a cp1518ni laserjet printer that prints fine black evenly spaced vertical lines on Photo's

The printer prints fine on Documents. I have changed out low toner cartridges, realigned the printer, and have installed additional memory and still the lines persist. I use the universal print driver for PCL 5. Any ideas?

Hello,
You should try upgrading to PCL6 UPD.
Here are a few links that might help:
Software and Driver Download page for CP1518ni:
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?cc=us&dlc=en&lc=en&os=2093&product=3422472&sw_la...=&
Information regarding thin lines:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01487425&tmp_task=solveCategory&cc=us&dlc=en&lc...=
Good luck,
Lagun
I work for HP, but my posts and replies are my own.
I am an HP employee
Say Thanks by clicking the Kudos Star if the post helped you.
Please mark the post that solves your problem as Accepted Solution.

Problem with threads and/or memory

I'm developing an application where there are 3 threads. One of them sends a request to the other, and if the 2nd can't answer it, it sends it to the 3rd (similar to CPU -> CACHE -> MEMORY). When i run the program with 1000-10.000 requests, no problem occurs. When i run it with 300.000-1.000.000 requests, it sometimes hangs. Is this a problem with the garbage collector, or should it be related to the threads mecanism.
(note: eache thread is in execution using a finite state machine)

i had been running the program inside Netbeans.
Running the jar using the command line outside
Netbeans i have no more problems... Does Netbeans use
it's own JVM?Depends how you set it up, but look under the options. There are settings for the compiler and jvm that it uses.

Mixing memory modules on Westmere

Dear Hardware gurus,
I have a 12-Cores Westmere. Do you know is it possible to mix different memory modules on it, namely:
6x1 Gb 1330Mhz
+
2x4 Gb 1066Mhz
and if yes, in which configuration?
Thanks a lot for any comment!

Kappy, thanks for the note.
I am actually going to order some more 1333 modules, but just for the short time I have to work with what I have currently (see my original post).
As I posted above, I tried a bit already to combine the modules and Mac doesn't boot
Can you suggest a configuration, which will work?

Lock ups and dumping psyical memory!!!

Hi i have just installed a new pc most of the stuff im useing is from my old computer so i know they work fine im running a:
P4 3GHZ Prescot 800MHz, HT-Enabled
865PE Neo2-P
512 DDR-400 Twin moss
ATI Radeon 9000 pro
PSU-400
XP Pro
My computer locks up alot when running intense games (games have worked before no problem) i also get a error saying dumping pysical memory, i have looked about and tried to solve this myself, i found that someone was haveing the exact same problem as me and he fixed it by turning the FSB down as his memory wasnt compatable with his motherboard if doing that works how do i do it ?
Many thanks Jonathan

Flappa, Your memory " clock" is fine and there is no need to "underclock it" as long as you did not mess with the Bios.
I had the same problems. I could not even get thru a Clean install of windows as it would Blue Screen
1- are you running in " Dual Channel Mode"?
2- If so is your memory a " match Set"?
some times memory even thought it has the same markings is not matched . Dual channel sets are matched and made to run together in "Dual Channel Mode"{
( Even though I had the same manufacturer memory my set would not run in Dual Channel without " Blue Screening" I bought a Matched Set of Kingston Valueram and have not had a problem since
3- If it is not a matched set, pull one stick out and run it for a while , if it still bluescreens try the other stick
4- raise your memory voltage to 2.7 or 2.8 ( which ever is the lowest that it runs stable)
5- If all this does not work , run MEMTEST to see if there is a problem with both sticks
6- you are running a Bios Version that supports the " Prescott Microcode" right?
Let us know what your findings are
Good Luck
Dave

Podcast client downloads to wrong memory

The podcast client on my N95 8GB have begun the annoying habit of saving downloaded podcasts the the phone memory, and not to the 8GB mass storage unit, where it used to put them.
Any ideas on how to rectify this problem?

The podcast client on my N95 8GB have begun the annoying habit of saving downloaded podcasts the the phone memory, and not to the 8GB mass storage unit, where it used to put them.
Any ideas on how to rectify this problem?

Memory upgrade on Satellite M30-344

Hi,
i have upgraded my memory from 2 x 256 mb to 2 x 512 mb, but nothing works. i bought the ram modules compatible to pa3312u-1m151.
this system doesn't boot, nothing happens. after reinstalling the old module, system starts normally.
what can i do?

Hi
This case is very clear. You have used not compatible memory modules.
As in the previous posting suggested, you should use the other compatible ram module.
If you dont know where to buy this part so please contact the Toshiba service partner in your country. There you will be able to order the right part.
By the way; I can confirm that the PC2100 512MB (PA3164U-1M51) is a right module

Memory upgrade on a Satellite A100-912

I own a Satellite a100-912 and I want to upgrade its memory!
As it seems, this model supports only PC2-4200 DDR2 SODIMM modules (533 Mhz). Before bying a memory module that might regret, I want to know if there will be any compatibility issues if I use to this laptop PC2-6400 DDR2 SODIMM module (800 Mhz).
Is it going to work even at lower clock speed (533 Mhz) or is it going to be a total waste of money?

As far as I know the FSB is able to handle 667Mhz modules.
You can use lower modules (533Mhz) without any problems but modules with higher Mhz will not run with full speed due to the limited FSB.
So I dont recommend buying 800Mhz modules. Firstly they are not supported and secondly its waste of money!

Memory slots on Lenovo G560

How many RAM memory slots has G560? I have 3GB of ram, 2 modules,first of 2GB and second 1GB. But when I run CPU-Z program it shows me 2 more free slots for ram. I couldnt find in user manual any information about memory slots and my laptop is under warranty yet so I dont want to open it to check,but I want to know how many slots are really there. Does anybody know?
Solved!
Go to Solution.

standard memory: 2 gb (removable) or 4 gb (removable)
maximum memory: 4 gb using a 32-bit operating system / 8 gb using a 64-bit operating system
expansion: 2 sockets
cpu & chipset: intel core i3 intel hm55
mfgr's system p/n's: 0679-xxx

Memory failures on Ex000 servers with 256 DIMMS and OBP_3.2.30,POST_3.9

Hi,
In the past 6 months I have had problems with systems that have had memory upgrades using 256MB modules, although initially the upgrades have gone OK when a module goes faulty you get random CPU panics and the system will crash to the OK prompt or a system reset, at no point does any useful information get posted in the messages file nor does the bank get deconfigured, also if you run extend post diags the memory passes all tests OK.
Any suggestions welcome.
Eddie

Eddie,
Please run the following two Solaris commands and paste the results back here.
# cat /etc/release
# uname -a
If there is a lack of information in MESSAGES, then there's a chance you may not
have a sufficient Solaris patch level.
The output of the two commands will guide us all a little bit better.

Memory problem on Msi x48c platinum

Hi every body,
I have a MSI x48c platinum mainboard,
Recently i bought a ddr3 memory module (corsair CMX4GX3M2A1600C9) trying to upgrade my system,
after replacing old memories with new ones, system didn't boot. Even bios setting page did not apear. So i installed old rams and by decreasing Dram frequensy at 1066MHz and then replacing old and new memories i managed to boot the system up and use the new modules.
Now the question is that how i can use the maximum of ram frequency? Which setting do you recomend?
I set everything else on auto at bios settings.
If you should know, i use an intel q9400 cpu.
Here is an image of my bios setting page where all settings are shown:
minus.com/lM5jHYAgmAwfI

Quote from: badboy2k on 07-September-12, 22:58:03
highest you will be able to use with your setup on the dimms will be 1333mhz with 2 dimms at timings of 9-9-9-24 command rate 2T at the most even if it boots at that frequency it may not be stable!
With a frequency higher than 1066 MHz system can't boot,
Quote from: xmad on 07-September-12, 22:59:26
Try doing a full cmos clear >>Clear CMOS Guide<< after installing the new memory in the proper channel.
By default that memory will operate at 1333 9-9-9-24 1t, see if it will boot after the cmos clear.
There have also been allot of bios updates that provided for better memory support, i suggest seeing what version you have and flashing to the newest. (with your old ram installed to ensure stability.)
I updated bios to last version (7.4), clearing cmos would default setting on bios thus system can't boot again.
Quote from: flobelix on 07-September-12, 22:59:54
Also try setting memory voltage to 1.65v and see if that works.
Have been trying memory voltage up to 1.83v, but it didn't work with memory frequency higher than 1066...

Memory ID, CP1518ni

Similar Messages

Maybe you are looking for