Memory only runs at 2T

My Corsair 1GB (2x512) Value memory only runs at 2T. This is the setting that comes up in AUTO. I tried going manual and setting it to 1T but the system froze and wouldn't boot then, I had to clear the bios and start over. I don't have any experience with overclocking, but thought it should be running at 1T. Any suggestions? Thanks.

About 1T/2T:
Quote
Hello,
1T and 2T Command Rate, also known as CPC or Command Per Clock, is a motherboard timing not a memory timing. 1T/2T commands indicate how the system clocks are allocating the timings of a command to the system. 1T = 1 clock cycle and 2T = 2 clock cycles.
On average there may be a performance difference in between 7-10% (depending on who you talk to, platform being run, benchmark used, etc)
1T/2T Command Rates can be setup differently based on manufacture, motherboard, processor type (Intel Vs. AMD) etc. At higher speeds, drivers, board layouts, chipset requirements all can add up to the system performance overall. Changing the 1T to a 2T command rate can stabilize the system if issues arise.
Since 1T-2T command rates are not a memory specification, Crucial does not list this as part of our overall module specification.
THOMAS THOR
Technical Support Analyst
Tel: (800) 336-8896
Tel: (208) 363-5790 (outside US & Canada)
Fax: (208) 363-5501
mailto:[email protected]
EDIT: Winnie og Venice CPU?

Similar Messages

  • 2 GB memory stick run with 1 GB memory stick?

    I'm looking into the possibility of maxing out the memory on my 2nd gen Macbook from 2 gb to 3gb, and have one question left.
    Would the fact that I'd have a 2gb Crucial memory stick running next to a 1 gb Apple memory stick throw off the optimization of the system so much that it would just be better to stick with the two apple issued 2gb memory sticks?

    First Magus wrote:
    It will not hurt anything as long as they are the same speed. I did it when I first got my MacBook. I installed a Crucial stick next to an apple supplied stick and it worked like charm. I wanted to add I used it for over a year like this with no noticeable problems while using programs such as Photoshop CS3.
    You know - after I read the Santa Rosa chipset datasheet, I'm starting to wonder even about this. Intel claims that the GMA965 is capable of controlling either "533 or 667 MHz" memories - meaning PC2-4200 or PC2-5300. A cursory reading said that a full dual channel setup is achieved by simply matching the sizes, and that if the speeds were not the same, it would revert to the lower speed on both channels. However - I haven't heard of anyone trying out a PC2-4200 module. My curiosity is now piqued, and maybe I can try that tonight with a Samsung PC2-4200 module I have lying around.
    Of course Apple could configure it such that only PC2-5300 is acceptable, but I didn't go so far into the datasheet to see what was in the configuration registers.
    Of course we've recently had the entertainment of someone claiming dire consequences from mixing and matching memory brands, but I think it's safe to say that shouldn't be an issue.

  • I got a Force Quit error box telling me to quit two applications because my startup disk was out of memory to run applications. What is this?

    I have a MacBook (mid-2007) with 2gb ram (max allowed) and recently upgraded to a 750 GB hard drive. And I have over 590 GB free Tonight I got a popup box requiring me to force quit my applications because I had run out of room on my startup disk. I was only running the finder, I-clean memory, Safari and mail at the time. I have been running that combination of programs forever and have never encountered this message. What is going on? 

    KKDani wrote:
    Do I delete things...?
    Yes. 
    Use this as a guide:
    http://pondini.org/OSX/DiskSpace.html
    Ciao.

  • HP 4510S laptop. has dual core processor but is only running one half of it.

    This system is running on Win 7 32bit.  If I upgraded to W7-64 bit would the system then use both halves of the processor?

    I use BELARC advisor which lists all hardware, SW on my system.  It also tells me what processors I have, memory, etc.  It will also tell me if I have a dual or single core processor and whether it is running both cores or only one.  My gateway NV50 is running Win 7-64 bit and BELARC tells me how it is working on both cores.  But my wifes LT which is an HP has win 7-32 bit for an OS and Belarc advises that it is only running one core.  That is why I asked the question.  I am upgrading the HD from 250 to 750 gb and maxing out her memory.  Maybe then she will quit complaining about how slow it works. 

  • Only runs with "optimized" settings

    Hi All,
       I have a 1GB kit of dual channel Mushkin Blue PC3200 installed on my K7N2 Delta2-LSR. Everything runs great except for when I attempt to change the memory settings to something other than "Optimized". The computer will then lock up while XP Home Edition is loading. Memtest shows no problems with the memory. I have a Athlon XP 3200+ and an Antec SL400 power supply. Right now the memory is set up in a standard configuration and NOT in dual channel. CPU voltage is set to 1.65v and the memory is set to 2.6v. Other than this small snafu the system runs great. Any ideas on how to troubleshoot this will be greatly appreciated. Thanks!
                                                                                                                                     John

    Wonka provided a link in a recent thread but it seems to have disappeared. The orinal thread is here:- https://forum-en.msi.com/index.php?topic=73527.0 Make sure that your hardware can handle the extra overclock if you want to use the B50 bios as it only runs stable with D.O.T. enabled.The "private" setting boosts FSB by 1% when the system is running under heavy load and 3% on "sergeant" setting etc.

  • 3gb ram only runs 333mhz

    I have at msi k8n neo 4 platinium,i use 2 run 2gb of ram(2x1gb)i just got another gb(2x512),so all ram slots are full,but now they only runs 333mhz,why's that i got the latest bios 1b

    Hi,
    I understand that you try to run 4 sticks of memory and it drops to DDR333?
    Well it's because of the CPU, AMD64's only support 4 banks of memory at full speed, but banks are not the same as slots.
    1 stick single sided = 1 bank
    1 stick double sided = 2 banks
    so 4 sticks double sided = 8 banks, ergo it drops.
    Some are lucky that it doesn't drop, but for most, yes it drops.

  • 4 dimms in Neo4 Plat. only runs at DDR333, but Venice should fix that?

    Now that I've added 2x256MB to my setup to get 1,5GB for Battlefield 2 and all 4 banks are filled, I can get neither the timings nor the frequency as high as I used to.
    Before with 2 banks: 2-2-2-5 1T @ 205MHz
    Now with 4 banks: well, all maxed out won't even get me past 193MHz.
    The manual says that with 4 dimms it can only run at DDR333, that much I know.
    But that was a processor limitation wasn'it? So with my Venice' suped up memory controller it should work, right?

    OK let's bust a big misconception. It is a limit that an A64 can run up to 4 banks of RAM at DDR400 and over 4 banks at DDR333.
    Sides do not equal banks. You can have a single sided DIMM that is 2 bank and even a Double sided DIMM that is one bank. You have to determine the number of Banks a Dimm has by the makers specs. Looking at how many sides a Dimm has is not always going to get the job done. Yes in some cases and maybe most you could be correct but you have to be sure and the only way to do this is to check with the makers to get their specs.

  • Is there a way to get a version of the Garage Band app that runs on version 5.1.1?  I have an iPad 1 and can't get any higher iOS.  The App store is telling me that Garage Band only runs on iOS 7.

    Is there a way to get a version of the Garage Band app that runs on version 5.1.1?  I have an iPad 1 and can't get any higher iOS.  The App store is telling me that Garage Band only runs on iOS 7.

    Unfortunately the answer is still no.

  • I am trying to run my registered CS6 Design Standard programs for the first time after install. InDesign runs OK, but Illustrator and Photoshop will only run in trail mode. How do I activate those two?

    I can't get my registered versions of CS6 Photoshop and Illustrator to run in full mode. I installed CS6 Design Standard online end of June (an upgrade from CS5.5), on my old MacBook Pro. I didn't run the programs then as I was waiting on arrival of new MacBook Pro. I migrated the programs from my old MacBook to the new, and today tried to run those programs for the first time. InDesign work OK (after an initial hiccup) but Illustrator and Photoshop will only run in trial mode, and won't let me save files. My CS6 Design Standard shows with it's registration in my Adobe Account. All seems in order, but Illustrator and Photoshop won't run in registered mode. Can you please help?

    Demons1 in the future please only migrate your documents and settings.
    Please use the uninstallers to remove your current installation.  They are located in the Applications/Utilities/Adobe Installers folder.  Once the uninstall is complete you will also want to run the CC Cleaner Tool.  You can find more details at Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6 - http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html.
    If you need to download a fresh copy of the installation files for Creative Suite 6 you can do so at Download CS6 products.

  • I uninstalled Firefox once, reinstalled it and it ran. I had a problem so I did it again. Now it will not run and I get an error message saying that firefox is running and you can only run one at a time. I can't figure out what is running.

    Because of a problem, I uninstalled Firefox once, reinstalled it and it ran. I had a problem so I uninstalled/reinstalled it again. Now it will not run. I get an error message saying that firefox is running and you can only run one at a time. I have uninstalled multiple times and can't figure out what is running. The is only one Firefox installed and it is not open. What does this mean and how do I fix it?

    If you use ZoneAlarm Extreme Security then try to disable Virtualization.
    *http://kb.mozillazine.org/Browser_will_not_start_up#XULRunner_error_after_an_update
    See also:
    *[[/questions/880050]]

  • I have a 3GS phone that can no longer be upgraded on my Powerbook because it is ancient and can only run 10.4.11, consequently itunes will only upgrade to 9.2.1(4). Is there any way i can upgrade the phone so hereafter i will not need a computer to do it.

    I have a 3GS phone that can no longer be upgraded on my Powerbook because it is ancient and the os will only run 10.4.11, consequently iTunes will only upgrade to 9.2.1(4). Please don't answer that i need to upgrade the computer os because that has been a past nightmare i have been through too many times.
    Is there any way i can upgrade the phone w/o going to an apple store so hereafter w/ the upgrade to the new os (whenever that gets squared away), i will not need a computer to do it?
    Thanks in advance,
    don

    Solved my issue by setting up a new account on my daughter's computer. Not 100% solved, but i was able to get the update on my 3GS.
    don

  • How do I set a Phase Listener to only run for a specific page?

    How do I set a Phase Listener to only run for a specific page?
    I understand that a Phase Listener runs for ever page in the application, however I want a phase listener to only run for one page at the beginning of the application.
    I discovered I can't use a Filter, because the JSF Application instance always returns null.
    Thus, I thought a Phase Listener would be a good approach.
    Thoughts?
    Thanks,
    --Todd                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                           

    I have moved forward with checking the requested URI...
    (shivers)
    Thanks,
    --Todd                                                                                                                                                                                   

  • Installed itunes 10.5.2 on my laptop and now it only runs in safe mode HELLLLP!!!

    I installed itunes 10.5.2 on my laptop and when it rebooted after it said that it could not connect to my ipod because of something to do with "apple mobile device" I tried unsuccessfully to find an answer and whilst trying to find an anwer my laptop froze and crashed and everything said it was not responding that was when it actually opened anything.
    I've found the solution to get it to connect to the mobile devices however my laptop will only run in safe mode and i cant fix the problem in safe mode!!
    My question is if I uninstall and reinstall itunes will i lose all my playlists? or does anyone have a solution to fix my itunes????????

    The Apple launch issues article suggests pulling 3rd-party plug-ins if the problem doesn't happen in Safe Mode.
    Here's the article that will walk you through the process -> iTunes: Troubleshooting issues with third-party iTunes plug-ins

  • I just installed Firefox on a new HP 600-1120 with Windows 7 and it is only running in "safe" mode. Why? How do I get it to run in "regular" mode? How does "safe" mode differ?

    I just installed Firefox on a new HP 600-1120 with Windows 7 and it is only running in "safe" mode. Why? How do I get it to run in "regular" mode? How does "safe" mode differ?

    > So now my question is, how can i fix this problem?
    Use the Toshiba recovery disk or the Toshiba HDD recovery option.
    If you dont have the Toshiba Recovery disk try the HDD recovery:
    http://aps2.toshiba-tro.de/kb0/HTD1303440001R01.htm
    This works only if the recovery image files from Toshiba are still on the HDD:
    If you installed the system using another disk as Toshiba recovery disk, this recovery option will not work.

  • DVD-drive only runs at 1x speed

    Hi
    Im having problem with my dvd-drive. It will only run at about 1x-speed. Not just when reading a DVD-movie but also when reading data DVDs.
    I have tried with two diffrent dvd-drives and they work fine in my other older computer but when I use them in my new computer they will only run at 1x speed.
    I have one SATA hard drive connected and the DVD-drive is connected to the primary IDE port.
    DMA is activated on the DVD-drive. I have also tried to turn that off but no difference.
    What can I do? Any help is appriciated!
    MSI P965 Platinum
    MSI GeForce 7900 GS
    Intel Core2Duo 6400
    RAM 1024MB

      Glad you got it solved. Yes, before posting, people should try the search feature, especially now with the new improved server. But, your post is still valuable and someone may find it in their search which would lead them to the solution.
    Again, glad it's working now.

Maybe you are looking for