Memory upgrade on Equium M70

I currently have 512KB of memory in my laptop, i want to increase this to 1GB.
Do i have to install another 512KB or replace this with 1GB.
Also do you have any information on where to purchase additional memory.

Hi
As Ivan already said, you can use the 512MB module if you want to upgrade the memory to 1024MB. The notebook should handle the max 2048MB memory.
So possibly you will upgrade the memory in the future to the higher value. In such case I would recommend buying the 1024 module immediately.
However, its your choice
The modules you can purchase from every notebook or computer dealer but I would recommend searching in the net for the best offer.

Similar Messages

Memory Upgrade on Equium A60

Hello,
I am looking to upgrade my memory on an Equium A60-155 C 335 by adding a 512mb component.
I know part: PA3312U-1m51 is compatable but does anyone know if Part: PA3312U-2m51 is also OK ?
Thanks.

Hi
I think that this memory module will work.
I have investigated a little bit in the internet and it seems that the PA3312U-2M51 module is a following memory module.

Memory upgrade on Equium A60 155

I have an Equium EA60-155 Notebook and the problem is it running very, very slow.
I would like to upgrade the memory. This laptop has only 1 slot and 256 non-removeable memory installed. My question is: what type of memory should I buy (can it be 512mb)

Hi
According to this page you can use also this memory module:
200-Pin PC2700 (333Mhz) DDR SODIMM
http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=13321&ft=m&st=3

Memory upgrade on Equium L20

I recieved an Equium L20 as a gift last year. Pretty much a month after getting it going, it has been very, very sluggish. It turns out it was sold to me with only 256Meg RAM - not even enough for XP to perform!!
I'm based out in the states now, and have been sent THREE different upgrades by a 'reputable on line memorystore' none of which have fit correctly..
The L20 forum claims that I need:
PC 4200 DDR2 - 533 SO DIMM
Is that correct?! I'm pretty sure the existing memory reads PC2700..
The problem seems to be that although the memory card lines up OK, the lateral grooves on each side that hold it in place do not line up with the arms in the memory slot.
Can anyone help? Please!!
Thanks
Dave

Hello
According the specification you can upgrade RAM with max 2GB. One slot is empty and there you can put additional RAM module. Maybe the better solution is to put module with more capacity in slot A and 256 MB RAM into slot B. Compatible modules are:
DDR2-400/533 256MB (PA3389U-1M25)
DDR2-400/533 512MB (PA3412U-1M51)
Bye

How do I physically fit memory into Equium M70-337?

Hello,
I am in the process of buying a memory upgrade for my Equium M70-337.
However I am unsure how to actually fit it.
I have unscrewed the memory panel and stared at it not really knowing what to do.
Any advice, any links to diagrams would also be highly useful.
Thanks for any help.

Hi
First of all before you install or remove a module, turn off the computer with the shut down option in the windows. The notebook shouldnt be in the standby or hibernation mode because you would lose the data.
Some memory modules can be physically installed but are not fully compatible with the notebook. In this case the machine will issue a warning like 3 short beeps.
Here a short instruction how to fin the modules;
- Turn the notebook upside down (dont forget to disconnect all cables) and remove the battery.
- Remove one screw securing the memory modules socket cover
- Slide your fingernail or a thin object under the cover and lift it off
- Fit the modules connectors into the computer connectors at about a 45degree angle and press the modules careful to ensure a firm connection.
- Push the module down so it lies flat. Latches on either side will lick into place to secure the modules.
But note; do this carefully and dont use any force!
Bye

Equium M70: Question about graphic card upgrade

Is it possible to upgrade this machine (spec's below) for better graphics preformance? Reading past postings left me with little hope. Any and all sound advice word be very appreciated. Many Thanks, Scott
Operating System: Windows XP Home Edition (5.1, Build 2600) Service Pack 2 (2600.xpsp_sp2_gdr.050301-1519)
Language: English (Regional Setting: English)
System Manufacturer: TOSHIBA
System Model: EQUIUM M70
BIOS: Ver 1.00PARTTBL
Processor: Intel(R) Pentium(R) M processor 1.73GHz
Memory: 502MB RAM
Page File: 456MB used, 772MB available
Windows Dir: C:\WINDOWS
DirectX Version: DirectX 9.0c (4.09.0000.0904)
DX Setup Parameters: Not found
DxDiag Version: 5.03.2600.2180 32bit Unicode
DxDiag Notes
DirectX Files Tab: No problems found.
Display Tab 1: No problems found.
Sound Tab 1: No problems found.
Music Tab: No problems found.
Input Tab: No problems found.
Network Tab: No problems found.
DirectX Debug Levels
Direct3D: 0/4 (n/a)
DirectDraw: 0/4 (retail)
DirectInput: 0/5 (n/a)
DirectMusic: 0/5 (n/a)
DirectPlay: 0/9 (retail)
DirectSound: 0/5 (retail)
DirectShow: 0/6 (retail)
Display Devices
Card name: Mobile Intel(R) 915GM/GMS,910GML Express Chipset Family
Manufacturer: Intel Corporation
Chip type: Intel(R) 915GM/GMS,910GML Express Chipset
DAC type: Internal
Device Key: Enum\PCI\VEN_8086&DEV_2592&SUBSYS_FF041179&REV_03
Display Memory: 128.0 MB
Current Mode: 1280 x 800 (32 bit) (60Hz)
Monitor: Plug and Play Monitor
Monitor Max Res: 1600,1200
Driver Name: ialmrnt5.dll
Driver Version: 6.14.0010.4497 (English)
DDI Version: 9 (or higher)
Driver Attributes: Final Retail
Driver Date/Size: 2/7/2006 08:56:16, 45697 bytes
WHQL Logo'd: Yes
WHQL Date Stamp: n/a
VDD: n/a
Mini VDD: ialmnt5.sys
Mini VDD Date: 2/7/2006 09:04:34, 1399615 bytes
Device Identifier: {D7B78E66-66D2-11CF-5863-0EDFA2C2CB35}
Vendor ID: 0x8086
Device ID: 0x2592
SubSys ID: 0xFF041179
Revision ID: 0x0003
Revision ID: 0x0003
Video Accel:
Deinterlace Caps: n/a
Registry: OK
DDraw Status: Enabled
D3D Status: Enabled
AGP Status: Not Available
DDraw Test Result: Not run
D3D7 Test Result: Not run
D3D8 Test Result: Not run
D3D9 Test Result: Not run

I have Satellite Pro M70. Generally the graphic card upgrade on notebooks is not possible. CPU maybe but graphic card . I really dont believe it.
Can you imagine what happen inside of notebook if the exchange could be possible?

Excessively High CPU usage on my Equium M70

HI,
Recently in the last month my CPU usage as been hitting 100% when Im not running any taxing software (just internet explorer and windows media player).
This is slowing down loading times and the area near the fan is pretty hot.
I have an Equium M70-337, with a 1.7 centrino processor, and now 2 gigs of RAM (formerly 512 megabytes). I upgraded the ram in December and had no problem like this, now it's just started happening recently, I haven't installed anything that would do it, there are no unnecessary programs running and this was after I restored my comp to factory settings with the startup disc (about a month after) so it seems to have come from nowhere. On the task manager list it shows my web browser and media player using up the majority of CPU but I could have sworn that they didn't use up this much before.
I don't know if the RAM would have been a factor but it was the correct ram for it and windows acknowledged to 2 gigs.
Why would this have happened suddenly, any ideas guys?

Hi
I have the same notebook model and at the moment I do not have such problems. To be honest I have made clean OS installation 3 months ago and after Microsoft update installation I have noticed that notebook does not run like before. Just for example: if I use IE7 intensively with several different tabs in task manager I can see that IE need over 300.000 k of memory and somehow blocks. After closing IE and ending the IE process sin task manager I can work normally again.
I really do not know how is your OS configured but in task manager you should see which running process is responsible for high CPU usage. Maybe some antivir application? Sorry but on this way it is really not easy to sayt why this happen. Play little bit with running processes.

Equium M70 - Bios UPDATE under Linux

Hi,
I will update my BIOS(Equium M70 psm78e) but the only file i can use is a .exe application which try to flash the bios while the system is working and, of course, under linux don't work!
Anyone knows another method?
Thanks a lot
CiaoCiao
Dex

… which is foolish on Toshiba's part, IMO.
Failing something Linux-specific, I'd settle for a BIOS upgrader which works in FreeDOS. That's doable, if it's provided as a complete CD image or (for some of us) can be added to an existing FreeDOS CD image.
This BIOS upgradability issue is something of an anti-recommendation, though it does have to be weighed against Linux-friendly hardware and a resident BIOS which causes no problems for Linux. (My Equium scores well on the latter two but unfortunately also on the first due to my having removed a certain commercial OS from its HD, despite which it +did+ get one BIOS upgrade.)

Equium M70-PSM77E: Garmin GPSMAP 60CS connection issue

I use Memory Map and have a Garmin GPSMAP 60CS, for some reason over the last few weeks, I cannot transfer routes and marks etc from the laptop to the GPS.
A message comes up saying unknown Garmin.
I have tried set-up and have downloaded the Garmin drivers, but when trying set-up again, none of the COM ports seem to be active.
Looking in Device Manager, none of the ports are shown and neither are they shown on the Control Panel listing.
My laptop is a Equium M70-PSM77E.
How do I get all the ports shown. I connect the Garmin via USB port.

Hi
You have connected this 3rd party device to the USB ports hmmm I have noticed a similar issue with my external USB HDD. For some reasons the external HDD stopped working.
This happened because I did not use the safely remove function.
I have spent a lot of times to get this HDD working. After a long investigation I have removed the USB ports from the device manager, cleaned the registry by using the cleaning software like CCleaner or Registry cleaner and rebooted the OS.
After this procedure the OS recognized the ports again and I was able to use the HDD.
So maybe this hint helps you

Equium M70: What is a max possible HDD size

Hi..
Does anyone know what is the maximum size hard drive this laptop can take.
It currently has a 40GB hard drive and i would like a larger one but am unsure what size i should get.

Hi
Ive found this forum thread;
http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=93195&#93195
the guy have an Sat M70. Its very similar to the Equium M70 series.
He was able to upgrade the M70 with the 160GB HDD. So it looks like its possible to use such big HDDs on the M70 notebooks.

Memory upgrade on iMac G3 700, help with system crashes

I tried to do a memory upgrade on my iMac, so I bought two kingston 256 MB PC133 modules, but none will work, the system starts, but hangs in about two minutes after loading the desktop. I went back to use the older memory module wich is an spectek, but I need the upgrade, any ideas?
Thanks!
FedericoMG.
Ps: Sorry about my english... I'm from Argentina... :-P

Hi Federicomg
The iMac 700 G3 should have been supplied with 1 stick of 256mb ram. However which is the correct type i am not sure as the Apple specifications for this model state PC100 whereas my iMac G3 700 graphite was supplied with 256 MB PC133-333 SDRAM
http://support.apple.com/specs/imac/iMacSummer2001.html
Apple profiler from my iMac this is the original supplied RAM from Apple:-
DIMM0/J13: Size: 256 MB
Type: SDRAM
Speed: PC133-333
1) I would re-instal the original ram and open system profiler to see what type the ram is.
2) Keeping the original stick in place add another stick of the new ram and look again in profiler to see if its recognised and again try the second stick to see if there's a problem with one of the sticks.
I am currently running my iMac with a small upgrade of RAM and the additional RAM is 128MB of PC100 and i have noticed the performance improvement since adding the PC100 so it's working and i have suffered no ill effects doing this..
paul..

MS-6195 memory upgrade

Hi,
My system is based on Ms-6195 K7 pro and Athlon 700 mhz. 192 Mb Ram (128Mb module + 64Mb module)
Problem:
when I try to upgrade memory with a sdram 256Mb PC100 module, the memory test can't finish and my system don't boot.
Please can you tell me how configure coreectly the BIOS or tell how to do.

MS-6195 memory upgrade.
I have also tried using new PC100 256Mb memory and am getting nowhere.
The ones that I have bought are single sided, [8 chips on only one side]
and do not work with my motherboard, however, if I put them into another,
older PC, it shows up as 128Mb.
So I assume that the DIMM is working OK, and that the 'old' PC has a memory size limitation??
I have tried the same things as wbs and Grommit and got the same results.
So I assume that the answer is in getting older DIMMs, double sided with 8 chips on either side.
Does this seem to be about right???

Memory upgrade fail - Kernel panic after put old memories back

I People, this is my first post here and unfortunately is to report a problem, not to help friends.
I did an memory upgrade last weekend. After this, he will not boot normally, only in safe mode.
I discovered that they sent me 1333Mhz memories, and my mac (mid 2009) supports only 1066Mhz.
I put the old memories again, however I believe that the system did not recognize.
As you can see below, the system recognizes two modules:
Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142353237334448302D4348392020
Memory Module: BANK 1/DIMM0, 4 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142353637334648302D4346382020
It is not true, I' using now 2 x 2GB, DDR3, 1067 Mhz (stock)
I tried to reinstall the system, but when I try, I got crash again.
how can I solve this issue?
Interval Since Last Panic Report: 5298 sec
Panics Since Last Report:          6
Anonymous UUID:                    EAEB74C4-4B23-BCC2-1A48-B6FEB255C9FF
Mon Apr 1 16:37:33 2013
panic(cpu 1 caller 0xffffff800e0876ab): "Spinlock acquisition timed out: lock=0xffffff8011bff270, lock owner thread=0x10d9fb0aa, current_thread: 0xffffff801f873000, lock owner active on CPU 0xffffffff, current owner: 0x10d9fb0aa"@/SourceCache/xnu/xnu-2050.7.9/osfmk/i386/locks_i386.c:363
Backtrace (CPU 1), Frame : Return Address
0xffffff80f54fbd10 : 0xffffff800e01d5f6
0xffffff80f54fbd80 : 0xffffff800e0876ab
0xffffff80f54fbdb0 : 0xffffff800e06256b
0xffffff80f54fbf40 : 0xffffff800e0b7f69
0xffffff80f54fbfb0 : 0xffffff800e0ce3d1
BSD process name corresponding to current thread: diskarbitrationd
Boot args: config="\OS X Install Data\com.apple.Boot" root-dmg=file:///OS%20X%20Install%20Data/BaseSystem.dmg
Mac OS version:
12A269
Kernel version:
Darwin Kernel Version 12.0.0: Sun Jun 24 23:00:16 PDT 2012; root:xnu-2050.7.9~1/RELEASE_X86_64
Kernel UUID: 8D5F8EF3-9D12-384B-8070-EF2A49C45D24
Kernel slide:     0x000000000de00000
Kernel text base: 0xffffff800e000000
System model name: MacBookPro7,1 (Mac-F222BEC8)
System uptime in nanoseconds: 8887270925
last loaded kext at 1689458563: com.apple.driver.AppleUSBTCButtons     235.4 (addr 0xffffff7f8f6c7000, size 20480)
loaded kexts:
com.apple.driver.AppleUSBTCButtons     235.4
com.apple.driver.AppleIRController     320.15
com.apple.driver.AppleUSBTCKeyEventDriver     235.4
com.apple.driver.AppleUSBTCKeyboard     235.4
com.apple.driver.DiskImages.ReadWriteDiskImage     344
com.apple.driver.DiskImages.SparseDiskImage     344
com.apple.driver.DiskImages.UDIFDiskImage     344
com.apple.driver.DiskImages.FileBackingStore     344
com.apple.driver.DiskImages.HTTPBackingStore     344
com.apple.driver.DiskImages.RAMBackingStore     344
com.apple.driver.AppleFileSystemDriver     3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless     1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib     1.0.0d1
com.apple.BootCache     34
com.apple.driver.AppleUSBCardReader     3.1.0
com.apple.iokit.SCSITaskUserClient     3.5.1
com.apple.driver.XsanFilter     404
com.apple.iokit.IOAHCIBlockStorage     2.2.0
com.apple.driver.AppleSmartBatteryManager     161.0.0
com.apple.driver.AppleUSBHub     5.1.6
com.apple.iokit.AppleBCM5701Ethernet     3.2.5b3
com.apple.driver.AirPort.Brcm4331     600.15.20
com.apple.driver.AppleFWOHCI     4.9.5
com.apple.driver.AppleAHCIPort     2.4.0
com.apple.driver.AppleUSBEHCI     5.1.5
com.apple.driver.AppleUSBOHCI     5.1.5
com.apple.driver.AppleEFINVRAM     1.6.1
com.apple.driver.AppleRTC     1.5
com.apple.driver.AppleHPET     1.7
com.apple.driver.AppleACPIButtons     1.6
com.apple.driver.AppleSMBIOS     1.9
com.apple.driver.AppleACPIEC     1.6
com.apple.driver.AppleAPIC     1.6
com.apple.driver.AppleIntelCPUPowerManagementClient     196.0.0
com.apple.nke.applicationfirewall     4.0.39
com.apple.security.quarantine     2
com.apple.driver.AppleIntelCPUPowerManagement     196.0.0
com.apple.driver.AppleUSBMultitouch     235.7
com.apple.iokit.IOUSBHIDDriver     5.0.0
com.apple.driver.DiskImages.KernelBacked     344
com.apple.iokit.IOSCSIBlockCommandsDevice     3.5.1
com.apple.iokit.IOUSBMassStorageClass     3.5.0
com.apple.driver.AppleUSBMergeNub     5.1.5
com.apple.driver.AppleUSBComposite     5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice     3.5.1
com.apple.iokit.IOBDStorageFamily     1.7
com.apple.iokit.IODVDStorageFamily     1.7.1
com.apple.iokit.IOCDStorageFamily     1.7.1
com.apple.iokit.IOAHCISerialATAPI     2.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily     3.5.1
com.apple.iokit.IOUSBUserClient     5.0.0
com.apple.iokit.IOEthernetAVBController     1.0.2b1
com.apple.iokit.IO80211Family     500.15
com.apple.iokit.IONetworkingFamily     3.0
com.apple.iokit.IOFireWireFamily     4.5.5
com.apple.driver.AppleMCP89RootPortPM     1.11
com.apple.iokit.IOAHCIFamily     2.2.0
com.apple.iokit.IOUSBFamily     5.1.6
com.apple.driver.NVSMU     2.2.9
com.apple.driver.AppleEFIRuntime     1.6.1
com.apple.iokit.IOHIDFamily     1.8.0
com.apple.iokit.IOSMBusFamily     1.1
com.apple.security.sandbox     220
com.apple.kext.AppleMatch     1.0.0d1
com.apple.security.TMSafetyNet     7
com.apple.driver.DiskImages     344
com.apple.iokit.IOStorageFamily     1.8
com.apple.driver.AppleKeyStore     28.18
com.apple.driver.AppleACPIPlatform     1.6
com.apple.iokit.IOPCIFamily     2.7
com.apple.iokit.IOACPIFamily     1.4
com.apple.kec.corecrypto     1.0
Model: MacBookPro7,1, BootROM MBP71.0039.B0E, 2 processors, Intel Core 2 Duo, 2.4 GHz, 8 GB, SMC 1.62f7
Graphics: NVIDIA GeForce 320M, NVIDIA GeForce 320M, PCI, 256 MB
Memory Module: BANK 0/DIMM0, 4 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142353237334448302D4348392020
Memory Module: BANK 1/DIMM0, 4 GB, DDR3, 1067 MHz, 0x80CE, 0x4D34373142353637334648302D4346382020
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.106.98.100.16)
Bluetooth: Version 4.1.3f3 11349, 2 service, 11 devices, 0 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: ST9500420AS, 500.11 GB
Serial ATA Device: MATSHITADVD-R   UJ-898
USB Device: Built-in iSight, apple_vendor_id, 0x8507, 0x24600000 / 2
USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0x26100000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x06600000 / 4
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8213, 0x06610000 / 7
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x06500000 / 3
USB Device: Apple Internal Keyboard / Trackpad, apple_vendor_id, 0x0236, 0x06300000 / 2

Hi BGreg,
I already reset the PRAM as you said.
I've cleaned the memory modules as indicated by Linc above.
Today I formatted my harddrive to try a clean install, but system crashs after 5%, 10%.
There is something making me worried:
In one of my tries, I opened the system view to check my actual hardware configuration, and to my surprise, the system shows me 8GB installed. Cannot be. I have 2 x 2GB.
Where my system stores this information? There is a way to reset it? I tried last hour install the snow leopard, that cames with my mac, by DVD, but does not worked too.
Thank you all so far.
Giuliano

Memory upgrade

Hi,
Can I install 2 x Crucial 4GB DDR3 - 1333 SODIMM 1.35V 204 PIN - CT51264BF1339J on a Macbook Pro 13 inch late 2011?
Currently, I have 4 GB (2 x 2 GB) and I want to upgrade to 8 GB. There is a controversial info regarding this particular memory module, some people say it is not compatible.
When I look to the specs I find:
204 PIN form factor = OK
1,35 V = OK
DDR3 = OK
1333 = OK
SODIMM = OK
Max 8GB = OK (2 x 4GB)
Latency= 9 cicles (same that stock modules supplied with the laptop) OK
The thing is Crucial, sell an identical specs module that costs quite more. They claim it to be compatible with Mac. The also sell this one I mentioned as being not compatible. The funny thing is that specs for both are identical. I only find a difference on the pricing. So I am really confused.
Do they one to sell me a more expensive one like being specific for Mac or there is a hiden specification that makes the two modules to differ from each other?
Can somebody confirm this info to me, please?
Many thanks in advance
Best Regards

News on this subject:
A Crucial support representative replied saying:
"Mac compatible memory is guaranteed to work in your specific system. There may be subtle differences in non specific memory that will cause it not to work for you such as chip solution and the configurations of chips..."
Well, I find it very ambiguous technically speaking. If they sell good quality memory as they claim, I do not see which subtle differences will affect the functionality. The chip configuration is standard and chip solution is about quality. So Crucial should be all right as everyone claims (even if manufactured in China)
So I went a head and both 2 x CT51264BF1339J for a very reasonable Belgian price and installed it into my system just two minutes ago. I am writing this using the mentioned system.
I was on Google after 30 seconds of taping the On button. Although it did not changed a lot as this startup timing is more related to the Hybrid 750GB HDD (SSD + Conventional Drive) I upgraded few months ago.
I upgraded the memory to run Virtual Box and Parallel desktop more easily though it worked quite good with 4GB. I did not upgraded to 16GB because it is not necessary on my usage. Only one virtual machine at once + E-mail + Browser + some PDF opened. Some technical stuff and nothing like Photoshop or similar. Thus the huge money difference would have gone for nothing if I buy the specific Mac modules of 8GB each as "Crucial Memory Upgrade Tool" subjected me.

Memory upgrade not working

I ordered 8GB memory for my imac mid-2011 model.
I then tried to install and all I'm getting is three beeps telling me there's something wrong with my memory.
I've tried all configurations but can't get the 2x4gb modules to work.
I've had to stay with only the original 2x2gb ones it came with.
Can anyone please help.
The only difference, besides the size, between the two modules is that on the 4gb ones is says PC3-10600S-9-10-F2 and the 2gb ones say all the same except instead of F2 at the end it's F1.
Cheers.

Which would seem to suggest that you may (unusually) have a doubtful memory module. Less unusually, you would have paid over the top for it.
Many people on these forums speak well of the following suppliers.
In North America contact OWC … Upgrade Apple iMac Memory
In Europe contact Crucial.com … RAM Memory Upgrade
Both companies have facilities to guide you and will recommend the correct memory package to meet whatever needs you describe to them.
There may be benefits buying from your own geographical location insofar as Shipping charges, Local sales taxes and Exchange rates. Check out the basic memory costs and do your sums next time you buy.

Memory upgrade on Equium M70

Similar Messages

Maybe you are looking for