Merged FX5200 Voltage and Linux Questions

Hello
I am about to change my motherboard, I intent to buy a Asrock 939DUAL SATA2. The voltage for the AGP grafic card is 1,5 V. Can I use my old personal cinema FX5200?

Hello
I know MSI says there are no support for linux for the Personal Cinema FX5200. But the Nvidia chip is supported with Linux drivers. Is there anyone who has experiance with linux and Personal Cinema FX5200

Similar Messages

MOVED: K8T Neo-FIS2R SATA and Linux Question

This topic has been moved to Operating Systems.
K8T Neo-FIS2R SATA and Linux Question

Quote
Originally posted by chasmon
Hi all,
I have just setup up a brand new system but am having probelms getting it working. I want to install XP on a single Maxtor 160Gb drive.
I have my HD on Promise Ser1 and all SATA stuff in BIOS enabled. When I get to the screen I press F6 and then when promted I insert the floppy with the promise drivers on. I then get this message:
"File txtsetup.oem caused an unexpected error (4096) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c"
I can't get past this screen I have tried:
1.Drivers from the CD supplied.
2.Drivers from the MSI website.
Please help me this lot cost lots of hard earned I'm pretty gutted at the moment. I have also tried the Via chipset with no joy.
System:
Antec 380W PSU and Sonata Case
LG DVDROM 8163B
NEC DVDR/RW 2500B
Panasonic Floppy
Neo FIS2R mobo
Maxtor Diamondmax Plus 9 160Gb SATA150
Benq RF K/B & Mouse
Don't spam man! I posted something to this same question in another thread.. from you no less! Make a new thread! lol
Hijacking = bad!
Ian

CPU VDD Control over Voltage and Temps questions

Hi Im running a msi890gxm-g65 with 1055t and g skill ddr3 ram at 1667 and am sitting overclocked at 3.5 Ghz with voltage at 1.375. I was trying to push it further so i know i had to increase my voltage but whenever i increased the option CPU Voltage in bios to any number it would always show as 1.375 in any program such as cpuz or coretemp. So i noticed i had to increase the CPU VDD Voltage option also to be able to obtain the voltage i wanted. So my question is how do those two work together? to obtain whatever voltage i want should i change both of these to the same number ?
Also in bios which i know is not idle I am noticing my temps at around 46C which is around what my full load will be with prime ( with a max of 50C after 12 hours for a short period) as reported by coretemp and hwmonitor. I know there is many reports that Thuban 1055t temps are not reported accurately in software programs so that it would be a good bet to add 10-15C to whatever the software temp is shown. So does anyone know how much load is put on system when bios is showing temperature, i just want to make sure im not running it to hot as i know they should not exceed 62C, and i expect to overclock it more then it currently is.

thanks im getting kind of confused though i noticed if i change CPU VDD Voltage and CPU Voltage to the same number it will change what is reported in cpuz VID. I changed it down to 1.35 instead of default 1.375.
So basically for CPU VDD VOLTAGE and CPU VOLTAGE do i need to change both of these to the same number to get required voltage needed for my overclock ?
Also i had to raise my CPU NB Voltage to be able to boot into windows past 3.8ghz and few minutes of prime seems fine.
My current settings are
CPU VDD VOLTAGE AND CPU VOLTAGE are at 1.387 and CPU NB VOLTAGE AND CPU NB VDD VOLTAGE are at 1.3
Running 272x 14 = 3.8 ghz and ddr3 memory running at 1450mhz.
I cant seem to get it past this ghz even when raising cpu to 1.475, should i raise cpu nb voltage more to achieve ? had same problem at 3.5ghz and cpu nb set to auto.
Are the voltages i posted safe ?? are CPU VDD VOLTAGE AND CPU VOLTAGE the same thing and cpu nb vdd and cpu nb vdd the same thing as well ?

I have forgotten my appleID password and the email it is linked to is deactivated, security questions aren't working. This is on my iPhone and iTunes acs so I can't sync with my new computer. How do I merge AppleID accounts and shut down the old one?

I have forgotten my appleID password and the email it is linked to is deactivated, security questions aren't working. This is on my iPhone and iTunes acs so I can't sync with my new computer. How do I merge AppleID accounts and shut down the old one (when I have no password and the security questions aren't working?)

You cannot merge Apple ID accounts, that has never been supported.
You can contact the Apple ID Security folks per the listing in http://support.apple.com/kb/HT5699 and they can help reset security questions and get the account working.

[SOLVED]Questions about openbsd ffs and linux ext2fs

Hello everyone.
First of all, forgive me if the post is not on the correct section.
I'm going to install arch linux to my thinkpad and i have some questions:
I have two external hard disks (once) formatted to openbsd ffs. (now i'm making efforts to turn it to ext2fs )
1) Does Arch have by default read support for openbsd ffs filesystems or i have to build a custom kernel?
2)I would mostly like to have read and write access from both OSs. I know that ext2fs should work for read and write from Openbsd and Linux so this could be a good option. My problem starts when i try it for example to format the disks under Openbsd; i successfully created a working ext2 partition, but when i try it
with an Ubuntu live cd to see if it works, i see no partitions and i have to reformat it. On the other hand, if i create it under Linux, then it's not working under Openbsd.
So now that i'm migrating to arch, which are the good practices to make partitions work/cooperate under both OSs?
notes: On Linux, i tried with both gparted and disk utility with no luck.( It works for linux but not for OpenBSD).
Has anyone managed to work with both ext2fs and both Linux Openbsd?
What are the best practices in such cases?
Last edited by lambda (2012-09-26 12:07:26)

well fstype is one thing , bsd labels vs mbr is another. In case with linux and bsd dualboot best practice is vfat (aka fat32) but with all its limitations ( i can be wrong here 'cos i never tested dual zfs for instance ).

Question regarding Oracle and Linux on VMware

Hello,
I carefuly read the paper on Oracle and Linux on Your Own VMware and I'm missing a point.
The paper explains how to start a cluster on a single host in a single Linux VM on VMware.
So, there are 2 instances of Oracle 10g DB on the same Linux VM inside VMware. What does allow that?
Is it possible to run 2 instances on any (single) Linux box, or is VMware required? If VMware is not required, why this complication in that paper? If VMware is required, what does it bring that make running 2 cluster instances on the same host possible?
Many thanks for your help.

userLynx wrote:
I have an oracle database (10.2) and I have a query that needs to compare data on the Oracle database to data on a MS SQL server DB. I'm using a DB Link between the two databases.
How would I compare the date fields?
I have a table that has a date as one of the fields and I need to restrict the records where the date is equal to the date on SQL, however the formats are different:
My query is as follows:
SELECT mkt_css_name,
pmv_rqst_corp_id,
pmv_rqst_source,
'G',
pmv_css_acct_no,
eq.start_date
FROM power_move@cmdt,
enroll_que@tcis eq,
marketer@cmdt
WHERE eq.css_account_number = pmv_css_acct_no
AND eq.requestor_type = 'P'
AND eq.status IN ('A','P','G','S')
AND eq.marketer_id = mkt_seq_no
AND pmv_service_type IN ('G','D')
And Pmv_Gas_Mktr_No = Eq.Marketer_Id
AND pmv_received_timestamp= eq.enroll_date ;
The problem is that the date is stored in Oracle in the following format: DD-MON-YYYY and in SQL as 'YYYY-DD-MM HH:MI:SSSSSS'
for example: Data in Oracle would be 27-JAN-2012 and in SQL as 2012-01-27 00:00:00.000
I get an error when I compile.
How do you reconcile the formats when the syntax is different between databases?
Thanks, SeanDATE datatypes do NOT have any "format"
DATE datatype is stored in internal binary notation.
use TO_CHAR to display, present & compare the DATE datatypes

[BASIC question] what is the component I should use to fix an AC voltage and its current (in the same component)

I need urgently to know how use a component which allows me to fix an AC voltage and its current.
I can't use a resistance and an AC current in parallele for my application..
Thanks a lot you will be very helpful !

In general the way to fix both voltage and current requires a source and an impedance, but you say you do not want that solution.
Please tell us exactly what your application is and why a current source in parallel with a resistance is unacceptable.
Lynn

DUAL BOOT windows 7 and linux HELP

MASTERS
im planing to have windows 7 and linux at the same time (DUAL BOOT)
but i dont know if one key recovery still works after installation
ihave lenovo g560
i3 @ 2.53
4gb ram
any advice guys?

hi botards01,
If you're planning to use linux occasionally (Ubuntu for example) and you don't want to risk losing the One Key Recovery functionality, try to install Ubuntu via Wubi as this doesn't repartition your HDD but creates a virtual disk on your current OS.
Check it out - Install Ubuntu in Windows With Wubi
Hope this helps
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Creating network between Mac and Linux

Hello guys! I need to set up network between my iMac and Ubuntu linux. iMac is connected in internet by Airport and Fon Wifi Router witch is connected in router which is connected to adsl -modem. My pc is connected directly to router. Both computers have access to internet. Is there any easy solutions to share files with mac and linux? I don't need any webservers etc, I just want to share files.
Other question related to this, why is my mac's ip address like 192.168... and linux ip addrress is 84.250...?
Thanks allready!

Though I'm not newbie with computers, I'm really confused becouse I haven't set up network like this never before.
Not a problem, no worry... we all know something somebody else doesn't and vice versa.
My linux says that my DHCP -IP is 193.210.18.18, is that related to this in any way?
Yes, if the Mac had an IP of 193.210.18.x, (but not 18 for x), then connection would be simple, but I think we must have two devices passing out IPs. What is the Mac's IP again?
http://www.helpdesk.umd.edu/topics/communication/ethernet/office/winxp/2882/
Do you have any advice where I could start looking from the right IP of my linux?
http://www.webmasterforums.com/networks-clusters/1804-find-ip-address-my-linux-b ox.html
I'm not sure if its even configurable.
http://tinyurl.com/2gug9s

Merge multiple cells and rows

Hello,
I am trying to merge multiple cells and have found that I can do thi easily by selecting the adjancent row cells and using the TABLE - MERGE CELLS command. However, If I want to apply the same merge to multiple rows, I can find noquick way to do this other than selecting each set of cells and using the TABLE - MERGE CELLS command each time. Here is an example of what I want to do:
Here is the Numbers spreadsheet as normal:
Here is cell B2 and C2 merged:
Now what I want to do is the same process for rows 3 to 10. However, when I try to select the section and use the TABLE - MERGE CELLS command, I get on large cell rather than split rows of merged cells as seen below:
Any idea how I can or if I can accomplish this task?
Thanks in advance,
OriginalGumshoe

You may also use this script :
--{code}
--[SCRIPT merge_row_by_row]
Enregistrer le script en tant que Script : merge_row_by_row.scpt
déplacer le fichier ainsi créé dans le dossier
<VolumeDeDémarrage>:Utilisateurs:<votreCompte>:Bibliothèque:Scripts:Applications :Numbers:
Il vous faudra peut-être créer le dossier Numbers et peut-être même le dossier Applications.
Sélectionner le bloc de cellules à traiter.
Aller au menu Scripts , choisir Numbers puis choisir “merge_row_by_row”
Le script fusionne les cellules de chaque ligne appartenant à la sélection.
--=====
L’aide du Finder explique:
L’Utilitaire AppleScript permet d’activer le Menu des scripts :
Ouvrez l’Utilitaire AppleScript situé dans le dossier Applications/AppleScript.
Cochez la case “Afficher le menu des scripts dans la barre de menus”.
Sous 10.6.x,
aller dans le panneau “Général” du dialogue Préférences de l’Éditeur Applescript
puis cocher la case “Afficher le menu des scripts dans la barre des menus”.
--=====
Save the script as a Script: merge_row_by_row.scpt
Move the newly created file into the folder:
<startup Volume>:Users:<yourAccount>:Library:Scripts:Applications:Numbers:
Maybe you would have to create the folder Numbers and even the folder Applications by yourself.
Select the range of cells to treat
Go to the Scripts Menu, choose Numbers, then choose “merge_row_by_row”
The script merge the cells of every row included in the selection.
--=====
The Finder’s Help explains:
To make the Script menu appear:
Open the AppleScript utility located in Applications/AppleScript.
Select the “Show Script Menu in menu bar” checkbox.
Under 10.6.x,
go to the General panel of AppleScript Editor’s Preferences dialog box
and check the “Show Script menu in menu bar” option.
--=====
Yvan KOENIG (VALLAURIS, France)
2011/12/18
--=====
on run
          local dName, sName, tName, rowNum1, colNum1, rowNum2, colNum2, r
          my activateGUIscripting()
          set {dName, sName, tName, rowNum1, colNum1, rowNum2, colNum2} to my get_SelParams()
          tell application "Numbers" to tell document dName to tell sheet sName to tell table tName
                    repeat with r from rowNum1 to rowNum2
                              set selection range to range (name of cell colNum1 of row r & " : " & name of cell colNum2 of row r)
                              my selectmenu("Numbers", 6, 23) -- Merge cells
                    end repeat
          end tell
end run
--=====
set { dName, sName, tName, rowNum1, colNum1, rowNum2, colNum2} to my get_SelParams()
tell application "Numbers" to tell document dName to tell sheet sName to tell table tName
on get_SelParams()
          local d_Name, s_Name, t_Name, row_Num1, col_Num1, row_Num2, col_Num2
          tell application "Numbers" to tell document 1
                    set d_Name to its name
                    set s_Name to ""
                    repeat with i from 1 to the count of sheets
                              tell sheet i to set maybe to the count of (tables whose selection range is not missing value)
                              if maybe is not 0 then
                                        set s_Name to name of sheet i
                                        exit repeat
                              end if -- maybe is not 0
                    end repeat
                    if s_Name is "" then
                              if my parleAnglais() then
                                        error "No sheet has a selected table embedding at least one selected cell !"
                              else
                                        error "Aucune feuille ne contient une table ayant au moins une cellule sélectionnée !"
                              end if
                    end if
                    tell sheet s_Name to tell (first table where selection range is not missing value)
                              tell selection range
                                        set {top_left, bottom_right} to {name of first cell, name of last cell}
                              end tell
                              set t_Name to its name
                              tell cell top_left to set {row_Num1, col_Num1} to {address of its row, address of its column}
                              if top_left is bottom_right then
                                        set {row_Num2, col_Num2} to {row_Num1, col_Num1}
                              else
                                        tell cell bottom_right to set {row_Num2, col_Num2} to {address of its row, address of its column}
                              end if
                    end tell -- sheet…
                    return {d_Name, s_Name, t_Name, row_Num1, col_Num1, row_Num2, col_Num2}
          end tell -- Numbers
end get_SelParams
--=====
on parleAnglais()
          local z
          try
                    tell application "Numbers" to set z to localized string "Cancel"
          on error
                    set z to "Cancel"
          end try
          return (z is not "Annuler")
end parleAnglais
--=====
on decoupe(t, d)
          local oTIDs, l
          set oTIDs to AppleScript's text item delimiters
          set AppleScript's text item delimiters to d
          set l to text items of t
          set AppleScript's text item delimiters to oTIDs
          return l
end decoupe
--=====
on activateGUIscripting()
(* to be sure than GUI scripting will be active *)
          tell application "System Events"
                    if not (UI elements enabled) then set (UI elements enabled) to true
          end tell
end activateGUIscripting
--=====
my selectMenu("Pages",5, 12)
==== Uses GUIscripting ====
on selectmenu(theApp, mt, mi)
activate application theApp
          tell application "System Events" to tell application process theApp to tell menu bar 1 to ¬
                    tell menu bar item mt to tell menu 1 to click menu item mi
end selectmenu
--=====
--[/SCRIPT]
--{code}
Yvan KOENIG (VALLAURIS, France) dimanche 18 décembre 2011 22:21:24
iMac 21”5, i7, 2.8 GHz, 12 Gbytes, 1 Tbytes, mac OS X 10.6.8 and 10.7.2
My iDisk is : <http://public.me.com/koenigyvan>
Please : Search for questions similar to your own before submitting them to the community

Acquiring multiple voltage and current sine waveforms, and log them along with the respective time stamp in a file."

"I am doing a data acquisition project using a 16 channel N.I. series 6020E card where I want to capture respective current and voltage sinusoidal signals. I am planning on capturing four pairs of matching current and voltage signals. I planned on taking one reading across the channels every fifteen minutes. This reading will need to be 60 data points per period or 3600 readings per second per channel in order for me to recreate the sine signal to determine the phase angle difference between the voltage and current. I was able to get one channel to capture a signal but could not get more than one working at a time. I am also trying to sycronize the data collection so all samples are with respect to each other. Thanks for any help."
-posted by cappy on 2/11/2002
John N on 2/12/2002 answered:
"Hi Cappy,
Could you post this question to the Hardware > Counter/Timer or Hardware > Multifunction I/O forums? I think you will get more responses there. Here is a link.
The hardware is usually a better differentiation since software can support such a huge range of functionality.
The data rates you are talking about sound reasonable. Are you using the USB or the AT interface?
One other thing to be aware of is that the samples taken will not be simultaneous due to the multiplexed nature of the MIO board measurements. However if you know the channel clock rate(output from one of the VI's), then you can calculate the time difference between each measurement and correct your phase measurements by that amount.
If you have more questions, please post this to the other forum and copy all of our discussion to let everyone know what we have talked about already.
Best Regards,
John Nieri
Applications Engineer
National Instruments"
I am using the USB connection. If anyone can help with or has a similar VI for this, it owuld be appreciated so I can work on the larger aspect of the total project.

The easiest VI to use for this acquisition is AI Acquire Waveforms in the data acquisition palette in LabVIEW. This VI allows you to perform a finite acquisition from multiple channels on your DAQ board. As John mentioned the acquisition from individual channels will not be truly simultaneous. There will be a slight time shift from one channel to the next on the order of the maximum acquisition speed of the card, 100kHz or 10 microseconds in your case. By accounting for this 10 microsecond delay between consecutive channels you can properly calculate the phase shift between voltage and current.
Christian L
NI Consulting Services
Christian Loew, CLA
Principal Systems Engineer, National Instruments
Please tip your answer providers with kudos.
Any attached Code is provided As Is. It has not been tested or validated as a product, for use in a deployed application or system,
or for use in hazardous environments. You assume all risks for use of the Code and use of the Code is subject
to the Sample Code License Terms which can be found at: http://ni.com/samplecodelicense

6140 and Linux woes

Hi,
I have a 6140 array attached to 2 McData 4400 (4 connections - each controller connects to each 4400).
Attached to the the 4400s i have several boxes, namelly some x4100s. the 4100s have each a dual port QLogic QLA2462 (sun branded).
Those boxes are intended to be xen Dom0s (64b) and connect to the 6140 thru the 4400s.
If i let one of those servers just to see one of the paths to one of the 6140 controllers (there are four, two coming from each 4400), it will see all 6140 Luns but on those that belong to the other controller it will bomb errors - (of the kind "Buffer I/O error on device sdf, logical block 7")
But it boots. Mess, is that i want to use multipath (SUN's provided rdac driver doesn 't seem to compile nicely with a pristine xen kernel) so i must use device-mapper-multipath, which kinda of works. It can see (with all paths exposed) all devices and so on... what it cannot see is that, for each path, only the volumes owned by the controller that terminates that path are actually useable, which makes fail-over actually a mess.
Question is - anyone actually uses dm-multipath with the 6140 and linux ? Am i doing anything blatantly wrong ? if so, which is the politically correct setup ? if rdac is the only way to go, where can i find a package that actually cooks with pristine upstream linux kernels ?
Thanxs in Advance
Ant�nio

hey,
only mpp will provide any useful multipathing under linux with 6140 arrays; dm-multipath doesnt work
(perhabs sometimes a special driver for dm-mp will exist?)
-- randy

What are the differences between HP-UX and linux?

Hi,
Could u please send me the differences between HP-UX and LINUX.
Thanks.

This is a forum about Oracle SQL and PL/SQL.
It is not about Unix or Linux.
Your question is inappropriate here and demonstrates inability to do any research on your own.
Sybrand Bakker
Senior Oracle DBA

Print services and linux clients

Hi,
I'm installing a Windows Server 2012R2 as a printer server. It must give support to all kind of clients (windows, os x and linux).
Then, I must use event id 307 and 805 to count printed pages.
My question is related with event 307 and linux clients. I'm asking linux users to configure their CUPS to connect using samba printer, for example, \\server\printer001 but when I check event id, I get no file name (Remote Downlevel Document), and most important,
I get 0 printed pages in param8. I did some testing using IPP, but I were not able to configure a printer in linux (couldn't manage to make linux clients to validate with their domain user account when using IPP). I tried configuring printer on server to render
jobs in server with no luck. Tried PS drivers just in case it was easier to CUPS to send info to server, but no luck either.
So, basically, is there any way to configure server (or linux client) so I get page count in event 307 in printservice? If I must configure IPP printing, how may clients configure their printers to validate using domain accounts?
Thanks!

Hi,
Sorry for delaying in reply.
Linux clients see page count. I've paused printing and checked some documents. Property page from a linux client document shows as this:
Documents sent from windows clients show same but they've document name and page count.
SPL archive copied from spooler printer on Windows server shows that info is present too:
%!PS-Adobe-3.0
%%Creator: cairo 1.9.5 (http://cairographics.org)
%%CreationDate: Thu Jun 19 14:15:48 2014
%%DocumentData: Clean7Bit
%%LanguageLevel: 2
%%DocumentMedia: Letter 612 792 0 () ()
%%Orientation: Portrait
%%For: (testuser)
%%Title: (Phaser 5500 Descarga del archivo)
%RBINumCopies: 1
%%Pages: (atend)
%%BoundingBox: (atend)
%%EndComments
%%BeginProlog
%%BeginFeature: *JobPatchFile 1
% Default Definitions
userdict /xerox$pagedevice <<
/MediaClass null
/MediaPosition null
/PageSize [612 792]
/TraySwitch true
/ManualFeed false
/ImagingBBox null
/ProcessColorModel /DeviceGray
/DeviceRenderingInfo currentpagedevice 1 index get 1 dict copy
/PostRenderingEnhance false
/Install {
xerox$old_install xerox$flip {
currentpagedevice /PageSize get aload pop translate 180 rotate
} if
>> put
<--- snip snip REMOVED FOR SIMPLICITY snip snip ------>
showpage
%%Trailer
%%Pages: 1
%%BoundingBox: 0 0 612 792
%%EOF
Linux client used official PPD file downloaded from xerox webpage for linux
cups. Windows server uses Xerox Global Print Driver PS 5347.600.0.0 type 3 with
Render print jobs on client computers as suggested by Alan before.
Any other idea?

Dual booting in Windows and Linux, but only Linux has calendar, TB 31.0

I'm dual booting using Linux Mint and Windows 7. I have TB 31.0 installed in each OS. TB in Linux has calendar capability; in Windows, there's nothing (by nothing, I mean no calendars - I can't see their properties, for instance, nor access them in any way).
I should add that both Windows and Linux TB programs are sharing the same profile folder (located on a separate partition), hence, all the same add-ons, passwords, etc.
The error console logs the following:
Timestamp: 14/08/2014 6:41:33 PM
Error: Components.classes[cid] is undefined
Source File: resource://calendar/modules/calUtils.jsm -> file:///P:/PortableApps/ThunderbirdPortable/Data/profile/extensions/%7Be2fda1a4-762b-4020-b5ad-a41df1933103%7D/calendar-js/calUtils.js
Line: 17
There are a variety of flow on errors, related to this.
My apologies for posting this in this way; I had intended to submit this via the crashreporter, but I'm having trouble getting the program to crash with this error just now.

A reply to my own question: it turns out that while sharing a profile works pretty well for most purposes, with Lightning it does not, as the extension has different Linux and Windows versions. The problem is solved quite simply: by not using the same profile for each version.
Glad to see that no one wasted time on this one (except me, of course).

Merged FX5200 Voltage and Linux Questions

Similar Messages

Maybe you are looking for