Message overflow on /dev/log minor #6 -- is syslogd (1M) running?

Hi, the console for sun v880 is giving the message as shown below:
message overflow on /dev/log minor #6 -- is syslogd (1M) running?
Note: The operating system is solaris 9. This same message is repeated and is full on console screen. Here we are having 2 nodes configured with sun clusters using sun cluster 3.1 software. And we are running oracle 9i RAC database. The message is repeating on one node, the other node is ok.
Kindly help me to solve this problem.
thanks,

What type of DVD are you using ?
could it be ODD-DVD SD-C2732 ? If so you should have its FIRMWARE version to 1055. Patch 120364-03

Similar Messages

  • Help troubleshoot this message: message overflow on /dev/log minor #5

    During boot with LOTS of disk LUNs I get this message:
    message overflow on /dev/log minor #5 -- is syslogd(1M) running?
    What is the cause of it?
    My system is Solaris 10 with up to date patches as of Jan 10/06.

    As supporting info that may be helpful, I have a V880 running Solaris 9 (not 10) that is seeing the same issue. This would appear to be a problem that is not limited to just Solaris 10.
    Sun Fire 880, No Keyboard
    Copyright 1998-2004 Sun Microsystems, Inc. All rights reserved.
    OpenBoot 4.13.0, 4096 MB memory installed, Serial #xxxxxxxxxxxx.
    Ethernet address 0:3:ba:86:3b:dd, Host ID: xxxxxxxx.
    Rebooting with command: boot
    Boot device: /pci@8,600000/SUNW,qlc@2/fp@0,0/disk@w2100000c5085aead,0:a File and args:
    SunOS Release 5.9 Version Generic_118558-19 64-bit
    Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
    Use is subject to license terms.
    message overflow on /dev/log minor #5 -- is syslogd(1M) running?
    My box essentially crashed over the weekend. Not really crashed but I was getting so many of these:
    message overflow on /dev/log minor #6 -- is syslogd(1M) running?
    syslogd: malloc failed: dropping message: Not enough space
    syslogd: malloc failed: dropping message: Not enough space
    syslogd: malloc failed: dropping message: Not enough space
    syslogd: malloc failed: dropping message: Not enough space
    that the box was essentially dead. 10-20 minutes between command outputs.

  • SetupApi.dev.log error message on driver install, but driver runs fine anyway... why?

    Hello,
    I am trying to run down the cause of the following warning/error message I see in my SetupApi.Dev.log file after I install a commercially signed driver.
    !    sig:           Verifying file against specific (valid) catalog failed! (0x800b0109)
    !    sig:           Error 0x800b0109: A certificate chain processed, but terminated in a root certificate which is not trusted by the trust provider.
    I see this error against all the files in the driver package, but the driver operation has so far been just fine.
    I have checked the certificate chain for the driver (there are 3 certificates in the chain: a root, an intermediate, and the code signing certificate I purchased, all from Verisign/Symantec), and compared the root and intermediate certificates against ones
    that are already installed on the machine where I installed the driver.
    Using the MMC, I can see:
     - the root certificate is located at:         Console Root->Certificates-Current User->Trusted Root Certification Authorities->Certificate
     - the intermediate certificate is located at: Console Root->Certificates-Current User->Intermediate Certification Authorities->Certificate
     - the code signing certificate is located at: Console Root->Certificates-Current User->Trusted Publishers->Certificates
    This all seems to make sense to me for as much as I've been able to research from the MSDN, so would there be some reason why this message shows up, yet the driver seems to install and operate correctly anyway?
    I am using VS 2012 Pro on top of Windows 7 (x64) Pro SP1 to perform the driver build and code signing.
    Thanks much in advance for reading this, and for any insight/advice you might have about this.
    Geoff

    Hi Pavel, Jason, and Bryan,
    I apologize for not getting back to this sooner, I got side tracked with a different task for a few days...
    I really appreciate your looking at my problem.
    I did some more digging and contacted VeriSign/Symantec for some assistance and learned
    I had a few things set up improperly with respect to my code signing certificate.
    VeriSign pointed me to a few links to straighten out my code signing certificate's chain of trust on
    my code-signing machine, and then they also pointed me to a couple links similar to the one
    Bryan provided here for the cross-signing certificate I needed.
    The links are provided below for reference (in case somebody else can make some use of them too)
    1. Disable root cert, so my certificate's signing chain of trust shows up:
     https://knowledge.verisign.com/support/code-signing-support/index?page=content&id=SO16958&actp=search&viewlocale=en_US
    2. Get the correct intermediate certs insalled:
     https://knowledge.verisign.com/support/code-signing-support/index?page=content&id=AR1739&actp=search&viewlocale=en_US
    3. Get the correct X-signing cert from MSFT (same dert as the one Bryan provided in his link):
     https://knowledge.verisign.com/support/code-signing-support/index?page=content&id=SO16763&actp=search&viewlocale=en_US
     https://knowledge.verisign.com/support/code-signing-support/index?page=content&id=SO5820&actp=search&viewlocale=en_US
    I'm building/signing this for Release, on a Windows 7 x64 platform. I am doing this using the
    Windows 8 WDK and VS 2012 Professional. It's a nice combination, as it automates the driver
    signing process.
    My driver is a package of files, and is signed with a CAT file.
    I wanted to be sure the files were signed correctly, so I ran "signtool" over each file in the package
    to verify the signing is correct. I've included the output from one of the files here. Save the filename,
    the output is identical for each file in the package.
    The signing certificate chain shown below matches my code-signing certificate chain when I examine it
    using the MMC-certificate snap-in.
    The cross certificate chain shown below is identical to the output from the VS 2012 IDE. Note the MFST X-signing
    certificate is in this chain from step 3 above, it's the second one from the top in the chain.
    ============================================
    output from signtool verification of package
    ============================================
    C:\Users\Me\Desktop\Driver\Package>signtool verify /v /kp /c mydriver.cat fileA.bin
    Verifying: fileA.bin
    File is signed in catalog: mydriver.cat
    Hash of file (sha1): nnnnnnnnnnnnnnnnnnnnnnnnnnnn
    Signing Certificate Chain:
        Issued to: Class 3 Public Primary Certification Authority
        Issued by: Class 3 Public Primary Certification Authority
        Expires:   Wed Aug 02 17:59:59 2028
        SHA1 hash: A1DB6393916F17E4185509400415C70240B0AE6B
            Issued to: VeriSign Class 3 Public Primary Certification Authority - G5
            Issued by: Class 3 Public Primary Certification Authority
            Expires:   Sun Nov 07 17:59:59 2021
            SHA1 hash: 32F30882622B87CF8856C63DB873DF0853B4DD27
                Issued to: VeriSign Class 3 Code Signing 2010 CA
                Issued by: VeriSign Class 3 Public Primary Certification Authority - G5
                Expires:   Fri Feb 07 17:59:59 2020
                SHA1 hash: 495847A93187CFB8C71F840CB7B41497AD95C64F
                    Issued to: My Company
                    Issued by: VeriSign Class 3 Code Signing 2010 CA
                    Expires:   Thu Jan 15 17:59:59 2015
                    SHA1 hash: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
    The signature is timestamped: Tue Mar 05 15:25:53 2013
    Timestamp Verified by:
        Issued to: Thawte Timestamping CA
        Issued by: Thawte Timestamping CA
        Expires:   Thu Dec 31 17:59:59 2020
        SHA1 hash: BE36A4562FB2EE05DBB3D32323ADF445084ED656
            Issued to: Symantec Time Stamping Services CA - G2
            Issued by: Thawte Timestamping CA
            Expires:   Wed Dec 30 17:59:59 2020
            SHA1 hash: 6C07453FFDDA08B83707C09B82FB3D15F35336B1
                Issued to: Symantec Time Stamping Services Signer - G4
                Issued by: Symantec Time Stamping Services CA - G2
                Expires:   Tue Dec 29 17:59:59 2020
                SHA1 hash: 65439929B67973EB192D6FF243E6767ADF0834E4
    Cross Certificate Chain:
        Issued to: Microsoft Code Verification Root
        Issued by: Microsoft Code Verification Root
        Expires:   Sat Nov 01 07:54:03 2025
        SHA1 hash: 8FBE4D070EF8AB1BCCAF2A9D5CCAE7282A2C66B3
            Issued to: VeriSign Class 3 Public Primary Certification Authority - G5
            Issued by: Microsoft Code Verification Root
            Expires:   Mon Feb 22 13:35:17 2021
            SHA1 hash: 57534CCC33914C41F70E2CBB2103A1DB18817D8B
                Issued to: VeriSign Class 3 Code Signing 2010 CA
                Issued by: VeriSign Class 3 Public Primary Certification Authority - G5
                Expires:   Fri Feb 07 17:59:59 2020
                SHA1 hash: 495847A93187CFB8C71F840CB7B41497AD95C64F
                    Issued to: MyCompany
                    Issued by: VeriSign Class 3 Code Signing 2010 CA
                    Expires:   Thu Jan 15 17:59:59 2015
                    SHA1 hash: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
    Successfully verified: fileA.bin
    Number of files successfully Verified: 1
    Number of warnings: 0
    Number of errors: 0
    =========================================
    As best as I can tell, this follows the kernel mode signing walkthrough doc, and assuming
    VS 2012 is doing the signing correctly, the driver package should have been signed correctly.
    The problem is, I still see the same error on the target machine.
    I've tried manually installing the code signing certificate in the target's Trusted Publisher Store,
    prior to installing the driver, but this does not keep the error from showing up.
    I honestly have no clue why. If the driver package files check out OK with the signtool on the signing
    machine, I'm at a loss for why the error shows up on the machine where I'm installing the driver.
    One other thing that is different is the code signing certificate's certification path When I insepct
    it on the target machine. It appears to have a different Root and (only one) intermediate certificate.
    The Verisign folks said this is "OK" because different machines have different certificates. I'm not
    sure I'm buying this statement. Does it make sense to you guys?
    The folks at VeriSign also told me I do not need ANY of the certificates used in signing the driver to
    be installed on the target machine. Does this make sense to you guys? I'm a little skeptical about
    that assumption too, but I haven't found any information on line to confirm or negate it.
    I'm really no further along in determining why I'm getting this error on my target machines.
    Does anything here look out of place to you?
    I'm half tempted to manually sign the driver package to is there's something going on inside the VS 2012
    IDE that could be causing this.
    Again, thanks for taking your time to read this.
    Geoff

  • Overflow message when retreiving formula log from DM

    The Data manager debug_logic.log file is about 5 Mb. When trying to retreive the log through the DM "view status" > formula log, we get the message "Overflow". So I assume that the file is too big. But after this message there is no other option than to close BPC and restart.
    Anyone experienced this before?

    Hi Bernard,
    This sounds to me like a known issue on 5.x versions: Overflow error occurs if logic debug log size is larger than 5Mo and Excel crashes. Under this circumstance, the only workaround is to open the log file from the file server.
    This issue has been fixed on SAP BPC 7.0 for the Microsoft platform: log file size display limitation has been enhanced to 30Mo.
    Hope it helps,
    Julien

  • When I try to open an image by double clicking on it in Bridge, I get a message telling me to log in to Creative Cloud.  I am running CS6, and the default should be to open files in Photoshop 6 or in Adobe Raw (if it's a Raw file).  I don't want to log in

    When I try to open an image by double clicking on it in Bridge, I get a message telling me to log in to Creative Cloud.  I am running CS6, and the default should be to open files in Photoshop 6 or in Adobe Raw (if it's a Raw file).  I don't want to log into CC since I am not a subscriber, and this means that I have to work around, and go  back to Bridge, and tell it to open the file in Adobe RAW.  However, this does not work for older psd files which for some reason cannot be opened in RAW.  How do I return to the process of simply allowing RAW files to open automatically in Adobe RAW, and simply right clicking on the image in Bridge to bring up the option of opening it in Photoshop?

    <moved from Adobe Creative Cloud to Bridge General Discussion>

  • With the error message in my sqlnet.log,what can I do?

    I am installing Oracle IAS Today in my win2000 server system.When I restart my computer,I fond these message in the sqlnet.log file :
    Fatal NI connect error 12515, connecting to:
    (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=yfz)(PORT=1521))(CONNECT_DATA=(SERVER=SHARED)(SERVICE_NAME=mouse)(PRESENTATION=http://admin)(CID=(PROGRAM=D:\Program Files\Oracle\jre\1.1.7\bin\jrew.exe)(HOST=YFZ)(USER=Administrator))))
    VERSION INFORMATION:
         TNS for 32-bit Windows: Version 8.1.7.0.0 - Production
         Windows NT TCP/IP NT Protocol Adapter for 32-bit Windows: Version 8.1.7.0.0 - Production
    Time: 25-1TB -2002 16:02:39
    Tracing not turned on.
    Tns error struct:
    nr err code: 0
    ns main err code: 12564
    TNS-12564: TNS#:>\>xA,=S(refuse connect)
    ns secondary err code: 0
    nt main err code: 0
    nt secondary err code: 0
    nt OS err code: 0
    What the problem is ?
    Any help appreciate!

    The Basic Troubleshooting Steps are:
    Restart..  Reset..  Restore from Backup..  Restore as New...
    Try a Reset of the Phone... You will Not Lose Any Data...
    Turn the Phone Off...
    Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
    The Apple logo will Appear and then Disappear...
    Usually takes about 10 - 15 Seconds...
    Turn the Phone On...
    If that does not help... See Here:
    Backing up, Updating and Restoring
    http://support.apple.com/kb/HT1414

  • Display error message in batch job log

    Hello
    I have a batch job running and I have an error coming during some validation logic.
    The problem is I need to continue the batch job when this error message comes and it should not cancel the batch job as it is doing currently but display that error message in batch job log, there are more similar error messages coming in job log and job gets finished, but when my error message comes job gets cancelled.
    I cannot give it as info message as it will give wrong idea about message type.
    Is there any FM by which we can add message in job log?

    Sanjeev I have done that but problem is I do not want to give that as Information message but Error message only and continue processing.
    If you see in screenshot 3rd message is given by me as information and you can see error messages also 6th and 7th and job continued till it is finished
    Basically I want that 'I' to be displayed as 'E'.
    Display error message in batch job log 

  • I keep getting an error message when trying to log on to FaceTime and iMessage on my iPad mini with wifi...could not sign in. Please check your network connection and try again. Help!

    I keep getting an error message when trying to log on to FaceTime and iMessage on my iPad mini with wifi...Could not sign in. Please check your network connection and try again. Help!

    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
    http://tinyurl.com/a7odey8
    Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/TS4268
    Using FaceTime and iMessage behind a firewall
    http://support.apple.com/kb/HT4245
    iOS: About Messages
    http://support.apple.com/kb/HT3529
    Set up iMessage
    http://www.apple.com/ca/ios/messages/
    Troubleshooting Messages
    http://support.apple.com/kb/TS2755
    Setting Up Multiple iOS Devices for iMessage and Facetime
    http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
    FaceTime and iMessage not accepting Apple ID password
    http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
    Unable to use FaceTime and iMessage with my apple ID
    https://discussions.apple.com/thread/4649373?tstart=90
    For non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
     Cheers, Tom

  • I am unable to update my apps... in my purchases page it appears as "update", then a message tells me to log on with the Apple ID I purchased the app with... Well I have tried my two different accounts and neither one will work, can someone help ??

    I am unable to update my apps... in my purchases page it appears as "update", then a message tells me to log on with the Apple ID I purchased the app with... Well I have tried my two different accounts and neither one will work, can someone help ??
    And is there any way to sync all my purchases and accounts to just have one... It is a bit stupid that you dont even get a list of something of what account you may of used, or some kind of hint, so you could log on to the right account. I am really stuck ...
    Please Advise......

    You can't merge accounts. But you can check your purchase history:
    iTunes Store & Mac App Store: Seeing your purchase history and order numbers
              http://support.apple.com/kb/HT2727
    Also, what may seem stupid to you... may be a protection of privacy to others.

  • Every time I boot up I receive the message that "iCal cannot log in to your iCloud account because you password is incorrect-" I do enter it correctly but the same error message comes up the next time the computer boots up.  How do I correct this issue?

    How do I correct the problem that every timeI boot up I receive the message that “iCal cannot log in to your iCloud accountbecause you password is incorrect…” I do enter it correctly but the same errormessage comes up the next time the computer boots up?  Thanks.

    Hello jwpg,
    Thank you for the details of the issue you are experiencing after restoring an iCloud backup.  I recommend the following articles for an issue like this:
    iCloud: "Incorrect Apple ID or Password" alert when setting up iCloud after upgrading to iOS 7
    http://support.apple.com/kb/TS5207
    iOS 7: If you're asked for the password to your previous Apple ID when signing out of iCloud
    http://support.apple.com/kb/TS5223
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • Can I reduce the message in the alert log ?

    Hi All,
    I receive lot of message in my alert log. Can I reduce the message in the alert log ? please help me
    Tue Sep 12 13:53:45 2006
    ARC0: received prod
    Tue Sep 12 13:56:13 2006
    LGWR: prodding the archiver
    Thread 1 advanced to log sequence 2105494
    Tue Sep 12 13:56:13 2006
    Current log# 4 seq# 2105494 mem# 0: E:\ORACLE\MMP\LOG\REDO04.LOG
    Current log# 4 seq# 2105494 mem# 1: C:\ORACLE\MMP\LOG\REDO04.LOG
    Tue Sep 12 13:56:14 2006
    ARC1: received prod
    Tue Sep 12 13:56:14 2006
    ARC1: Beginning to archive log# 3 seq# 2105493
    ARC1: Completed archiving log# 3 seq# 2105493
    ARC1: re-scanning for new log files
    ARC1: prodding the archiver
    Tue Sep 12 13:56:18 2006
    ARC0: received prod
    Tue Sep 12 13:58:26 2006
    LGWR: prodding the archiver
    Thread 1 advanced to log sequence 2105495
    Tue Sep 12 13:58:26 2006
    Current log# 1 seq# 2105495 mem# 0: C:\ORACLE\MMP\LOG\REDO01.LOG
    Current log# 1 seq# 2105495 mem# 1: E:\ORACLE\MMP\LOG\REDO01.LOG
    Tue Sep 12 13:58:27 2006
    ARC1: received prod
    Tue Sep 12 13:58:27 2006
    ARC1: Beginning to archive log# 4 seq# 2105494
    ARC1: Completed archiving log# 4 seq# 2105494
    ARC1: re-scanning for new log files
    ARC1: prodding the archiver
    Tue Sep 12 13:58:31 2006
    ARC0: received prod

    Hi,
    The Oracle database writes an audit trail of the archived redo log files received from the primary database into a trace file. This parameter specifies the level of trace that should be generated when redo logs are archived. The value of the parameter indicates the level of trace to be generated.
    Level      Description
    0      Disabled (default)
    1      Track archival of redo log file
    2      Track status of each archivelog destination
    4      Track archival operational phase
    8      Track archivelog destination activity
    16      Track detailed archivelog destination activity
    32      Track archivelog destination parameter changes
    64      Track ARCn process state activity
    128      Track FAL server related activities
    It can be used in a Primary Database or Standby Database
    for more details see:
    http://docs.nojabrsk.ru/sol10/B12037_01/server.101/b10823/trace.htm
    Cheers

  • Messages in the OS logs of Oracle Solaris on SPARC (64-bit)

    One of my Customer is getting following messages in the OS logs of the Oracle Solaris on SPARC (64-bit) machine.
    Feb 2 01:07:33 ndc-m9k-2-r1 Invalid ioctl opcode = 0x403
    Feb 2 03:07:43 ndc-m9k-2-r1 scsi: [ID 243001 kern.warning] WARNING: /pseudo/fcp@0 (fcp0):
    Feb 2 03:07:43 ndc-m9k-2-r1 Invalid ioctl opcode = 0x403
    Feb 2 04:07:34 ndc-m9k-2-r1 oracle[7332]: [ID 566193 user.error] n2a get_local_info: ioctl (get interface flags): Interrupted system call
    Feb 2 05:07:52 ndc-m9k-2-r1 scsi: [ID 243001 kern.warning] WARNING: /pseudo/fcp@0 (fcp0):
    Feb 2 05:07:52 ndc-m9k-2-r1 Invalid ioctl opcode = 0x403
    Feb 2 07:08:08 ndc-m9k-2-r1 scsi: [ID! 243001 kern.warning] WARNING: /pseudo/fcp@0 (fcp0):
    Feb 2 07:08:08 ndc-m9k-2-r1 Invalid ioctl opcode = 0x403
    Feb 2 09:08:25 ndc-m9k-2-r1 scsi: [ID 243001 kern.warning] WARNING: /pseudo/fcp@0 (fcp0):
    Feb 2 09:08:25 ndc-m9k-2-r1 Invalid ioctl opcode = 0x403
    There is a note # 833665.1 on this which states "The issue is caused by the Host Storage metrics collected by the agent" and also a Patch 8477122 has been created for this issue.
    However, there is nothing mention in the Note # 833665.1 about the following one message.
    Feb 2 04:07:34 ndc-m9k-2-r1 oracle[7332]: [ID 566193 user.error] n2a get_local_info: ioctl (get interface flags): Interrupted system call
    Can anyone please tell me
    1. whats the significance of the "oracle[7332]: [ID 566193 user.error] n2a get_local_info: ioctl (get interface flags): Interrupted system call" message in the OS log?
    2. Does this message get stops on applying of patch # 8477122 ?
    Thank you,
    Bhavin

    There are a number of known issues with the 10g agent on Solaris and patches are available. I assume you are running the 10.2.0.5 agent since you reference patch 8477122. If this is a brand new agent installation i would start with applying the latest PSU update which contains many related fixes. If you are still getting the error after this, open an SR with Oracle Support with your specific error message.

  • Getting an error message when trying to log on to imessage

    Getting an error message when trying to log on to imessage... how do I fix this

    Whart does the message say?
    Maybe:
    iOS: Troubleshooting FaceTime and iMessage activation
    iOS: Troubleshooting Messages

  • I once created an account and changed meanwhile my Apple ID. Now, when trying to log in to iCloud, I get the message: "You are already logged in". I cannot get access to the account in the way, that, for example, the options appear on the right hand side.

    I once created an account and changed meanwhile my Apple ID. Now, when trying to log in to iCloud, I get the message: "You are already logged in". I cannot get access to the account in the way, that, for example, the options appear on the right hand side.
    What can I do?

    Thank you, pvonk, but:
    To be more precise: I am talking about the logging-in within the System Preferences on my iMac.
    When trying to log in with the old ID, I get no access, i.e. it says "Try again"...-Trying the same with the new one gives me the result I mentioned in my first question...
    Now I found out how to do it: I had to erase all accounts-then I could sign in with my Apple-ID. Thanks again.

  • Can text messages in the incompletion log be found in any table?

    We need to store and review the text messages found in the online incompletion log.  Does anyone know if these are stored in a table?  Or if they are always redetermined upon VA01 or VA02 transactions, does anyone know at what point in what program this happens if we need to build our own custom table to capture the messages?

    The incompletion log table is VBUV - Sales Document: Incompletion Log
    I think the table is filled in one of the following:
    > Function module - RV_CHECK_DOCUMENT_INPUT
    > Include - LV45FFUV: FORM FEHLER_BESTIMMEN
    I hope this helps.
    Gerard
    P.s. Also look for structure VBUV_TAB as I think XVBUV comes for here.
    Edited by: Gerard Magorrian on Oct 1, 2010 9:04 PM

Maybe you are looking for

  • ITunes won't work, please help

    Hello Apple Discussions. I've been having trouble with my iTunes account. Every time I try to open the program it tells me that an error has occurred and has to close. I've been reading through what other people have tried to get around this problem,

  • After updating my iPhone 5 to iOS 8.0.2 my safari, mail and calendar won't open. How do I rectify this issue?

    I recently updated my iPhone 5 to the iOS8.0.2 version and since then I cannot access my safari, my mail and my calendar icon is blank.  Every time I touch the icon it just blinks, the phone screen goes white and then it reverts back to the main scre

  • How to "fix" RV180/180W Certificate Errors

    When I access setup on a RV180 or RV180W with Internet Explorer the following message always displays: "There is a problem with this website's security certificate. The security certificate presented by this website was not issued by a trusted certif

  • How to get rid of section headers?

    The "Mailboxes" "On my Mac" etc are taking up unnecessary space... anyone know a way to get rid of those headers and just have the folder icons? Think I can tell the difference between a smart mailbox and my inbox from the icons thank you

  • Need information related to oracle 10g standard / enterprise edition (diff)

    Hi, I had developed my application using oracle 10g enterprise edition and now i wanna to shift the entire thing to oracle 10g standard edition. i Ha ve query on thiis point. 1) Is it safe to do so. 2) what are the difference between both the edition