Messages in Recording state in IEng

Hi All,
In RWB I see some messages are in recording state. I am unable to delete these messages. Can't we delete messages with record state.
In SMQ1 & SMQ2 all queues are clear.
If I am not wrong there are differrent queues for IE & AE. Can I ignore IE messages and only cancel the error messages
which are in AE.
If I don't cancel these messages from IE, in PRD can this cause messsge struck in future.
Regards,
Krishna Chauhan

Hi Krishna,
As far as i understand, these messages have been recorded in the DB for processing and since the resources are not free currently, these will be picked up for processing later. So, in short these messages will be processed later so there is nothing to worry unless the message size is huge or you don't have any custom module which processes the message before the standard "CallSAPAdapter" module or any such custom processing.
Regards, Gaurav

Similar Messages

Supplicant sent malformed PEAP message - bad record MAC

Hi all,
A specific kind of endpont, a device called Raspberry PI, is unable to connect or keep connected to our wireless network and the message generated by ISE is : Supplicant sent malformed PEAP message - bad record MAC
the WLAN accepts AES end TKIP and both have been tested.
I got some logs from WLC. Hope someone out there could help me.
*dot1xMsgTask: Aug 27 20:26:40.673: 00:e7:a6:56:86:8c dot1x - moving mobile 00:e7:a6:56:86:8c into Connecting state
*dot1xMsgTask: Aug 27 20:26:40.673: 00:e7:a6:56:86:8c Sending EAP-Request/Identity to mobile 00:e7:a6:56:86:8c (EAP Id 1)
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.699: 00:e7:a6:56:86:8c Received EAPOL EAPPKT from mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.699: 00:e7:a6:56:86:8c Received Identity Response (count=1) from mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.699: 00:e7:a6:56:86:8c EAP State update from Connecting to Authenticating for mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.699: 00:e7:a6:56:86:8c dot1x - moving mobile 00:e7:a6:56:86:8c into Authenticating state
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.699: 00:e7:a6:56:86:8c Entering Backend Auth Response state for mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.700: 00:e7:a6:56:86:8c Received EAPOL EAPPKT from mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.700: 00:e7:a6:56:86:8c Received Duplicate EAP Response Identity packet with eapid=1 from mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.702: 00:e7:a6:56:86:8c Received EAPOL EAPPKT from mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.702: 00:e7:a6:56:86:8c Received Duplicate EAP Response Identity packet with eapid=1 from mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.726: 00:e7:a6:56:86:8c Processing Access-Reject for mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.726: 00:e7:a6:56:86:8c Removing PMK cache due to EAP-Failure for mobile 00:e7:a6:56:86:8c (EAP Id -1)
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.726: 00:e7:a6:56:86:8c Sending EAP-Failure to mobile 00:e7:a6:56:86:8c (EAP Id -1)
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.726: 00:e7:a6:56:86:8c Entering Backend Auth Failure state (id=-1) for mobile 00:e7:a6:56:86:8c
*Dot1x_NW_MsgTask_4: Aug 27 20:26:40.726: 00:e7:a6:56:86:8c Setting quiet timer for 5 seconds for mobile 00:e7:a6:56:86:8c

Hi,
Thank you for your response!
Do you mean that there's something wrong with some version of the 'iaik_ssl.jar' ?
How do I determine which version we're running and what version is 'the older' version of the iaik_ssl.jar ?
Regards

When trying to download firefox 3.6.18 which is compatabile with my school I get a 403 message at that states mozilla is forbidden on this server, how do i correct e problem

when trying to download firefox 3.6.18 which is compatabile with my school I get a 403 message at that states mozilla is forbidden on this server, how do i correct the problem

Reload web page(s) and bypass the cache.
* Press and hold Shift and left-click the Reload button.
* Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
* Press "Cmd + Shift + R" (MAC)
Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
* Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove Cookies" from sites causing problems:
* Tools > Options > Privacy > Cookies: "Show Cookies"

Windows Server 2008: Sysprep Error: Error [0x0f0073] SYSPRP RunExternalDlls:Not running DLLs; either the machine is in an invalid state or we couldn't update the recorded state, dwRet = 32[gle=0x00000020]

I have a base template (which has never been sysprep'd) from which I create linked clones. After the linked clone comes up, I run the following command:
c:\windows\system32\sysprep\sysprep.exe /generalize /oobe /reboot /unattend:c:\windows\panther\unattend.xml
This works fine for the first few linked clones, but after about 3-4 linked clones are running, I start to hit "A fatal error occurred while trying to sysprep the machine."
****c:\windows\panther\setuperr.log****
2013-03-29 16:40:07, Error      [0x0f0073] SYSPRP RunExternalDlls:Not running DLLs; either the machine is in an invalid state or we couldn't update the recorded state, dwRet = 32[gle=0x00000020]
2013-03-29 16:40:07, Error      [0x0f00a8] SYSPRP WinMain:Hit failure while processing sysprep cleanup providers; hr = 0x80070020[gle=0x00000020]
****c:\windows\panther\unattend.xml****
<?xml version='1.0' encoding='utf-8'?>
<unattend xmlns="urn:schemas-microsoft-com:unattend">
    <settings pass="oobeSystem">
        <component name="Microsoft-Windows-International-Core" processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
            <InputLocale>en-US</InputLocale>
            <SystemLocale>en-US</SystemLocale>
            <UILanguage>en-US</UILanguage>
            <UILanguageFallback>en-US</UILanguageFallback>
            <UserLocale>en-US</UserLocale>
        </component>
        <component name="Microsoft-Windows-Shell-Setup" processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
            <AutoLogon>
                <Enabled>true</Enabled>
                <Username>Administrator</Username>
                <Password>
                    <Value>ca$hc0w</Value>
                    <PlainText>true</PlainText>
                </Password>
            </AutoLogon>
            <OOBE>
                <HideEULAPage>true</HideEULAPage>
                <NetworkLocation>Work</NetworkLocation>
                <ProtectYourPC>3</ProtectYourPC>
            </OOBE>
            <UserAccounts>
                <AdministratorPassword>
                    <Value>ca$hc0w</Value>
                    <PlainText>true</PlainText>
                </AdministratorPassword>
            </UserAccounts>
            <TimeZone>Pacific Standard Time</TimeZone>
        </component>
    </settings>
    <settings pass="specialize">
        <component name="Microsoft-Windows-Shell-Setup" processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
            <ProductKey>7M67G-PC374-GR742-YH8V4-TCBY3</ProductKey>
            <ComputerName>*</ComputerName>
        </component>
    </settings>
</unattend>
****c:\windows\panther\setupact.log****
2013-03-29 16:40:07, Info       [0x0f004d] SYSPRP The time is now 2013-03-29 16:40:07
2013-03-29 16:40:07, Info       [0x0f004e] SYSPRP Initialized SysPrep log at c:\windows\system32\sysprep\Panther
2013-03-29 16:40:07, Info       [0x0f0054] SYSPRP ValidateUser:User has required privileges to sysprep machine
2013-03-29 16:40:07, Info       [0x0f0056] SYSPRP ValidateVersion:OS version is okay
2013-03-29 16:40:07, Info       [0x0f005e] SYSPRP ScreenSaver:Screen saver was already disabled, no need to disable it for sysprep
2013-03-29 16:40:07, Info       [0x0f007e] SYSPRP FCreateTagFile:Tag file c:\windows\system32\sysprep\Sysprep_succeeded.tag does not already exist, no need to delete anything
2013-03-29 16:40:07, Info       [0x0f005f] SYSPRP ParseCommands:Found supported command line option 'GENERALIZE'
2013-03-29 16:40:07, Info       [0x0f005f] SYSPRP ParseCommands:Found supported command line option 'OOBE'
2013-03-29 16:40:07, Info       [0x0f005f] SYSPRP ParseCommands:Found supported command line option 'REBOOT'
2013-03-29 16:40:07, Info       [0x0f005f] SYSPRP ParseCommands:Found supported command line option 'UNATTEND'
2013-03-29 16:40:07, Info       [0x0f004a] SYSPRP WaitThread:Entering spawned waiting thread
2013-03-29 16:40:07, Info                         [sysprep.exe] UnattendFindAnswerFile: Looking at explicitly provided unattend file [c:\windows\panther\unattend.xml]...
2013-03-29 16:40:07, Info                         [sysprep.exe] UnattendFindAnswerFile: [c:\windows\panther\unattend.xml] meets criteria
for an explicitly provided unattend file.
2013-03-29 16:40:07, Info                  SYSPRP SysprepSearchForUnattend: Using unattend file at [c:\windows\panther\unattend.xml].
2013-03-29 16:40:07, Info                  SYSPRP SysprepSearchForUnattend: [generalize] pass in unattend file [c:\windows\panther\unattend.xml] either doesn't exist or passed
validation
2013-03-29 16:40:07, Info                  SYSPRP WinMain:Found unattend file at [c:\windows\panther\unattend.xml]; caching...
2013-03-29 16:40:07, Info                  SYSPRP WinMain:Processing unattend file's 'generalize' pass...
2013-03-29 16:40:07, Info                  SYSPRP Sysprep is running a generalize pass with the following unattend file: [%windir%\panther\unattend.xml]
2013-03-29 16:40:07, Info                  SYSPRP RunUnattendGeneralizePass: Sysprep unattend generalize pass exits; hr = 0x0, hrResult = 0x0, bRebootRequired = 0x0
2013-03-29 16:40:07, Info       [0x0f003f] SYSPRP WinMain:Processing 'cleanup' request.
2013-03-29 16:40:07, Error      [0x0f0073] SYSPRP RunExternalDlls:Not running DLLs; either the machine is in an invalid state or we couldn't update the recorded state, dwRet = 32[gle=0x00000020]
2013-03-29 16:40:07, Error      [0x0f00a8] SYSPRP WinMain:Hit failure while processing sysprep cleanup providers; hr = 0x80070020[gle=0x00000020]
2013-03-29 16:48:52, Info       [0x0f004c] SYSPRP WaitThread:Exiting spawned waiting thread
2013-03-29 16:48:52, Info       [0x0f0059] SYSPRP ScreenSaver:Screen saver was originally disabled, leaving it disabled
2013-03-29 16:48:52, Info       [0x0f0052] SYSPRP Shutting down SysPrep log
2013-03-29 16:48:52, Info       [0x0f004d] SYSPRP The time is now 2013-03-29 16:48:52

Hi,
This is typical of an OEM license issue.
To avoid this in the future you should look at site/volume licensing.
Anyway.
so, first check if you can re-arm by runing the
slmgr.vbs /dlv and check the re-arm counter, if it set to zero.. you need to do the following :
http://support.microsoft.com/kb/929828 (set the <SkipRearm>1</SkipRearm> like in the example, note: this option will make the product key window to appear in the setup process).
you can also try running : slmgr.vbs -rearm, to rearm Windows.
after that, let's come back to the sysprep process.. for syspreping already syspreped machine we have to change few keys in the registry :
HKEY_LOCAL_MACHINE\SYSTEM\Setup\Status\SysprepStatus\GeneralizationState\
CleanupState:2
HKEY_LOCAL_MACHINE\SYSTEM\Setup\Status\SysprepStatus\GeneralizationState\
GeneralizationState:7
After done with the registry, do the following :
Start -> Run : msdtc -uninstall (wait few seconds)
Start -> Run : msdtc -install (wait few seconds)
Restart the machine
Check the registry for the right registry keys values
sysprep with the new XML answerfile.
Source: Olegm
If you find my information useful, please rate it. :-)

T4i Rebel error message "movie recording has stopped automatically"

I was recording my client when suddenly I got a this error message "movie recording has stopped automatically" and I could not record video anymore. I am recording on a class 10 sandisk Ultra card. 720/60, EFS18-135mm lens. Never had any problems in the past. First I get a small veterical meter on the frame and then after 5 secs the recording stops with this error message. Please tell me it is opeartor error...I have had this camera for 2 years now and never had a problem. I tried multiple cards.
thanks for the help,
DM

Either you or the person you spoke to at Canon was confused.
What the camera requires for video purposes is a card which is "at least" Class 6 or faster. The class designation is an indicator of the cards data transfer speed. Class 6 actually means the card is capable of transfering data (either reading or writing) at "at least" 6 megabytes per second. A Class 10 card can transfer data at "at least" 10 megabytes per second.
The T4i is also compatible with "UHS-1" cards... which are significantly faster than eithe Class 6 or 10.
The reason for requiring "at least" Class 6 has to do with how fast the camera is attempting to capture and save frames of video to the card. The camera actually has an internal memory buffer which is very fast. When you start recording, the data is being saved to that buffer... and simultaneously the camera also starts taking the data from the buffer and saving it to the memory card (which is slower). If the camera is recording video only slightly faster than the card can record, then it will actually take a few minutes before the buffer is completely filled. But at that point the camera has no choice but to stop recording because it has absolutely no place to save data ... the internal buffer is full and it can't empty the buffer because the memory card can't save data as fast as new frames of video are coming in.
Faster is always better.
Memory cards do actually wear out and develop errors over time. This is normal. A good card will re-map the bad blocks so they aren't used anymore... and this is why you should do a low-level format IN CAMERA (not using the computer). Good cards also have a "memory leveling" technology to try to use all the blocks roughly an equal number amount. This extends the userful life of the card.
When replacing the card, do not skimp on quality! I cannot emphasize that point enough. Most times when someone brings up this issue... it's the card that is having problems and not the camera.
It's easy to produce forgery cards which look like a good brand but are not. Buy GOOD cards from REPUTABLE dealers. Do not shop for the cheapest website on the Internet with a questionable reputation in order to save a couple of bucks.
Lexar brand and SanDisk brand are good.
When buying memory cards, I only buy cards from Lexar and SanDisk. I also buy their highest end cards (by speed performance... not necessarily their biggest capactiy cards). I buy the cards from dealers with a solid reputation. This avoids the unpleasant error messages which always seem to happen at the worst possible time.
Tim Campbell
5D II, 5D III, 60Da

Getting Accessiblity Error Message before Recording Software Simulation...

In Captivate 7, I go to start a brand new software simulation (chrome screen) in OSX and I get the following error message:
Before recording application applications, select 'Enable Access for Assistive devices' in 'System Preferences' > 'Accessibility'.
The pics below show the red screen capture box and the error I get when I try to capture when trying to capture the screen. Also included is a pic showing accessibility is enabled.
I have no idea where this is coming from.

...and here's the answer:
http://captivatecrazy.blogspot.com/2014/01/record-new-software-simulation-in-adobe.html

I am having an installation failure issue with my itunes 11 software. File is corrupted and i don't know what to do. I've un-install and re-installed the software three times and continue to get the same error message. It states that "This copy of ITun

I am having an installation failure issue with my itunes 11 software. File is corrupted and i don't know what to do. I've un-install and re-installed the software three times and continue to get the same error message. It states that "This copy of ITunes is corrupted or is not installed correctly. Please reinstall Itunes"
iMac, iOS 6

HI,
If your old version of iTunes is still working - then I sugest you stick with that.
iTunes 11 is a lousy update - It will not retain your playlists, you can't find and delete duplicates... and a whole arry of oyher issues. (have a look around this forum to see how many issues IT11 gives people)
Just a friendly advise and warning :-)

Mass update for message condition records

Hello all,
with Transaction NACE we maintained thousands of message condition records.
Now we have to change for all this message condition records the "Number of Messages" (Table NACH Field ANZAL).
Is there a mass change Option available or is there a function module we could use?
Thank you
Best regards
Manfred

Dear Manfred
i think you want to change All condition records of some condition type In NACE , you want to change Date and Time ex:
Am i right ?
Yes it is possible in NACE T.code level only
So here Give What is Your application like V2
Now click on condition record and Just go to change mode And give application V2 Example
after this change Date here it will applicable to all condition type what ever in your V2 Application and all condition type
Apart from This i thing some Function Module May be there but i cant recall
Please let me know
Thanks a lot

I was forced to upgrade to latest version and when I try to burn a disc I receive the message "disc recording not found"

I was forced to download the lastest version, purchased music, and when I try to burn to disc I receive the following message " Disc recording not found" Please help very frustrated

Could you post your diagnostics for us please?
In iTunes, go "Help > Run Diagnostics". Uncheck the boxes other than DVD/CD tests, as per the following screenshot:
... and click "Next".
When you get through to the final screen:
... click the "Copy to Clipboard" button and paste the diagnostics into a reply here.

I have an iphone 4, how do I take stored voice messages and record them to a stick?

I have an iphone 4, how do I take stored voice messages and record them to a stick? A family member passed away and I want to keep their voice.

Hey there!
Sadly, there is no way to do this.
I'm sad to hear you've lost a familymember.
Try this: Move in a quiet-room. Play his/her voice over speaker of your iphone and record it with free recording-softwarefor windows or mac.
Hope this will help you keeping the memory.

When syncing I received a error message 1611 that state I need to restore my phone. How can I do this and not loose my contacts?

When Syncing my iphone I received a error message 1611 that states my phone needs to be restored and itunes needs newest version of updates. when I cked updates it states I DO have the newest version 10.5.3??? Can I restore my phone without loosing ALL my contacts?

If you've been syncing your contacts to a compatible address book or cloud service as intended, you can just re-sync them. If not, you're pretty much hosed. Contacts are not part of the iPhone backup.

Display message when record is save in table

Hello,
How can i display message as "Record Save" when record successfully save into table.
I have created a form and take one save button, when values fill up in the textboxes and SAVE button pressed record is successfully inserted in the table then
but how can i display popup window that "Record is save".
Thanks in advance.

Hi,
your page process can have a "success message" which will be displayed after this process has finished and the page is freshly displayed (if your branch doesn't filter the process success message).
This would be the easiest way to display "Record is save", if you want to do this in a Popup (which is oldskool...) then you can add some javascript code to your process success message.
brgds,
Peter
Blog: http://www.oracle-and-apex.com
ApexLib: http://apexlib.oracleapex.info
BuilderPlugin: http://builderplugin.oracleapex.info
Work: http://www.click-click.at

Getting error message "missing ; before statement 24"

Hello,
I'm getting the error message "missing ; before statement 24" in the following script:
//Create a variable to hold the document object
var StartDate = (xfa.form.form1.page1.signature.StartDate.rawValue);
var EndDate = (xfa.form.form1.page1.signature.EndDate.rawValue);
var assocName = (xfa.form.form1.page1.signature.assocName.rawValue);
var assocID = (xfa.form.form1.page1.subForm1.assocID.rawValue);
var assocEmail = (xfa.form.form1.page1.subForm1.assocEmail.rawValue);
var assocExt = (xfa.form.form1.page1.subForm1.assocExt.rawValue);
var assocDept = (xfa.form.form1.page1.subForm1.assocDept.rawValue);
var mgrName = (xfa.form.form1.page1.subForm1.mgrName.rawValue);
var mgrEmail = (xfa.form.form1.page1.subForm1.mgrEmail.rawValue);
var salariedHourly = (xfa.form.form1.page1.subForm1.salariedHourly.rawValue);
var directReports = (xfa.form.form1.page1.subForm1.directReports.rawValue);
var perfRating = (xfa.form.form1.page1.subForm1.perfRating.rawValue);
var howLongWorking = (xfa.form.form1.page1.request.howLongWorking.rawValue);
//SUBMIT DATE
if (StartDate == "") Then
xfa.host.messageBox( "Please enter a Submit Date" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.StartDate");
//HIRE DATE
elseif (EndDate == "") Then
xfa.host.messageBox( "Please enter a Hire Date" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.EndDate");
//NAME OF ASSOCIATE
elseif (assocName == "") Then
xfa.host.messageBox( "Please enter your Name" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.assocName");
//ASSOCIATE ID
elseif (assocID == "") Then
xfa.host.messageBox( "Please enter your ID" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.assocID");
//ASSOCIATE EMAIL
elseif (assocEmail == "") Then
xfa.host.messageBox( "Please enter your email address" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.assocEmail");
//ASSOCIATE EXTENSION
elseif (assocExt == "") Then
xfa.host.messageBox( "Please enter your telephone extension" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.assocExt");
//ASSOCIATE DEPARTMENT
elseif (assocDept == "") Then
xfa.host.messageBox( "Please enter your department" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.assocDept");
//MANAGER NAME
elseif (mgrName == "") Then
xfa.host.messageBox( "Please enter your manager's name" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.mgrName");
//MANAGER EMAIL
elseif (mgrEmail == "") Then
xfa.host.messageBox( "Please enter your manager's email address" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.mgrEmail");
//SALARIED HOURLY
elseif (salariedHourly == "") Then
xfa.host.messageBox( "Please enter whether your are salaried or hourly" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.salariedHourly");
//DIRECT REPORTS
elseif (directReports == "") Then
xfa.host.messageBox( "Please indicate whether you have any direct reports" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.directReports");
//PERFORMANCE RATING
elseif (perfRating == "") Then
xfa.host.messageBox( "Please certify your last performance rating" );
xfa.host.setFocus("xfa.form.form1.page1.subForm1.perfRating");
//HOW LONG WORK
elseif (howLongWorking == "") Then
xfa.host.messageBox( "Please indicate how long you anticipate working this arrangement" );
xfa.host.setFocus("xfa.form.form1.page1.questions.howLongWorking");
else
Button6.execEvent("click");
page2.presence = "visible";
EndIf
I've been hunting for several hours and can't seem to find or correct the problem. Can anyone help?
Thanks,
MDawn

I'm still having trouble. I tried to change the script to JavaScript. Now I'm getting "subForm1 not defined" error message. But it appears that subForm1 is set up properly.
Any thoughts?
Thanks,
MDawn

HT203175 i receive the message "disc recording not found" would not burn my cd

I can't burn my cd - I get the following message: "disc recording not found"?

I'd start with the following document, with one modification. At step 12 after typing GEARAspiWDM press the Enter/Return key once prior to clicking OK. (Pressing Return adds a carriage return in the field and is important.)
iTunes for Windows: "Registry settings" warning when opening iTunes

MM Message Condition Records

Hi,
We have migrated Message Condition Records to new Purchase Organisation. Now while creating new RFQ's or PO's with new Purchase organisation, the message condition is in green but print is not coming. If we check in the processing log, it says Processing log doesnt exist. It is not even going to Spool (SP02). Whereas while creating RFQ or PO with Old Purchase organisation print is coming and also visible in spool. All the settings for Message condition type and record are same. Even we are unable to print preview the PO with new Purchase Org. We have checked the Print Forms and Routines also. There also no check is there for new Purchase Org. Can anyone help us.
Regards/
Praneeth

Hi,
Did you try to o/p in me29n? what the response? Have you maintained the condition records in MN01/02 for the combination of new org enttities? Perhaps thats why spool isnt created since there might not be object data for the destination entities.
check the following thread might help
Output type PO - NEU spool request
Thanks
Shiva

Messages in Recording state in IEng

Similar Messages

Maybe you are looking for