MGCP Gateways and Cisco Fax
We are considering adding a fax solution to our IPT infrastructure using Cisco Fax (Captaris RightFax). Ideally we would like the same voice gateways to terminate the fax calls (internal voice calls use QSIG and external calls use Q.931). Can this be achieved with MGCP-controlled Voice gateways? Can T.38 fax be configured with an MGCP gateway. I have seen examples where H.323 dial-peers are required to talk SIP to the Fax Server.
If not, is an alternative to use a back-to-back PRI connection between a voice gateway port and the Fax Server ISDN card, with appropriate route patterns in CallManager to route the fax calls to Fax Server, using Cisco Fax Relay?
with cm 4.2.3 there is mgcp t.38 support implemented.
see release notes cm 4.2.3
http://www.cisco.com/application/pdf/en/us/guest/products/ps6729/c1178/ccmigration_09186a0080724724.pdf
regards
mehmet
Similar Messages
-
Cisco Fax Server (Captaris) and Cisco Fax Relay
Hello all!
i know that Captaris Cisco Fax Server works well with T.38 Fax Relay...and what about Cisco Fax Relay? Is it compatible?
thanks,
metHi!
Please check the following link, specially Pg. 9 "ISDN/MGCP Cisco Fax Relay Mode" . You'll see the deployment models of the Cisco Fax server: IP T.38 Fax Relay, ISDN E1/T1 Direct Connection and ISDN/MGCP Cisco Fax Relay Mode:
*** Installation Guide Supplement for Cisco Fax Server ***
www.cisco.com/en/US/docs/voice_ip_comm/fax_server/90/faxigsup.pdf
Hope this helps!
Regards,
Teresa.
If it helps, please rate! :) -
Cisco Call Manager 5.1 and Cisco VoIP Gateways
Hi,
I have Cisco Call Manager 5.1 with Cisco 2800 series routers as a ISDN gateways and Cisco VG224/ATA 186 as POTS gateways. While Cisco Call Manager collects call statistics from 7900 series SCCP handsets managed by the Call Manager (number of VoIP packets, dropped frames etc.), it shows only one side of the call as it does not collect statistics from the Cisco routers (configured as H.323 gateways), the Cisco VG224 (with ports configured as H.323 gateways and as a SCCP devices) and Cisco ATA 186 (configured for SCCP).
Is the collection of these statistics possible? What needs to be done?
Thanks,
PaulUpdate: Logging of QoS/Call Management Records (CMR) to Call Manager CDR database is not possible with H.323 gateways; only MGCP gateways:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_qanda_item09186a008020650a.shtml#qa4
Anyone know how to get the Cisco router gateway to log these statistics anyway using standard router logging mechanisms (e.g. syslog)?
Anyone know about calls to SCCP ports on Cisco VG224 or ATA 186?
Thanks,
Paul -
FAX Detection Application for a MGCP Gateway
Hi,
I have an MGCP Gateway and a Right Fax Solution along with CUCM. Was wondering if FAX detection application can be configured for this setup or is FAX detection only for H323 gateways.
Thanks
PrakashIt uses TCL script, so it is not available with MGCP.
Chris -
Hello - we are trying to configure SRST on our T1 CAS MGCP gateway. We have been informed by a Cisco engineer that we cannot use SRST on a T1 CAS MGCP gateway and that the gateway must first be reconfigured as an H.323 gateway in order to implement SRST. Router is version 12.2(15)T14 and CCM 4.1 Any comments would be truly appreciated...thank you.
SRST doesn't support MGCP but does support MGCP to H.323 failback. You can still configure your router/CCM with MGCP then use the fallback commands for MGCP.
Looking at the SRST 4.0 system guide, page 42, T1 CAS is supported. With your version of IOS you would be running SRST 2.1, this is also supported.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/srst21/srstv21.pdf
http://www.cisco.com/univercd/cc/td/doc/product/voice/srst/srst40/srst40ad/s40sa.pdf
The ccm-manager fallback-mgcp command was added in IOS 12.2(11)T so it should be in your version. This is what you would need to do MGCP fallback to your H323 along with the call application alternate default.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123tcr/123tvr/vrht_c4.htm#wp1061367
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123tcr/123tvr/vrht_c1.htm#wp1670149
I would say it might be possible as I don't see anything saying no. Though remember MGCP fallback to H323 over SRST doesn't have call preservation.
Lastly here is a document on the SRST MGCP/H323 fallback.
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a008012ecc6.shtml
Please rate any helpful posts
Thanks
Fred -
Hello, I trying to intergate Cisco Fax 9.4 with CCM7,
Schema is E1--> GW2921 -->H323 --> CCM7 --> H323 --> FAX.
FAX --> H323 --> CCM
GW config:
HQ#sh run | s dial-peer
dial-peer voice 1 pots
description ---Incoming_Calls_From_PSTN---
incoming called-number .T
direct-inward-dial
port 0/0/0:15
forward-digits all
dial-peer voice 3 voip
description ---To_CCM---
destination-pattern ^222222$
session target ipv4:10.52.205.2
dtmf-relay h245-alphanumeric
codec g711ulaw
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
dial-peer voice 2 pots
description ---v_Gorod---
destination-pattern 9......
port 0/0/0:15
forward-digits 6
dial-peer voice 6 pots
destination-pattern 98..........
port 0/0/0:15
forward-digits 11
Cisco Fax Server - is H323 Gateway on CCM 7
Fax Server is pointing to CCM this way:
Brooktrout Conf Tools -> H.323 -> Primary Gateway (CCM IP)
I have 1 dialing rule:
Pattern: +
Number Adjustments
Prepend this: @CCM IP
And I have two Users created in Right Fax Enterprise Fax Manager:
First - route code 7000
Second - route code 7001
I trying to sent fax from FaxUtil of first user to FaxUtil of thw second user.
First user (route code 7000) push New Document button in the FaxUtil and fill rows:
Name: "First"
Fax Number: 7001
push "Send" button
and status of fax message is stucked in "Sheduled to be Sent" status.
I see that user 7001 have 1 Faxes, but that is no actions more.
Please, if some one know what is a problem, help,
Thanks.You, also, have the dreaded and EVEEL MacKeeper installed. Git rid of eeeet!!!
Here is the way to properly uninstall MacKeeper.
http://applehelpwriter.com/2011/09/21/how-to-uninstall-mackeeper-malware/
Here is some more pertinent info about MacKeeper and its ilk.
Apps like MacKeeper or any other maintenance apps like CleanMyMac 1 or 2, TuneUpMyMac, MacCleanse or anything like these apps, installed on your Mac, while they appear to be helpful, can do too good a job of data "cleanup" causing the potential to do serious data corruption or data deletion and render a perfectly running OS completely dead and useless leaving you with a frozen, non-functional Mac.
Plus, these type of apps aren't really necessary OR needed. They really aren't.
There are manual methods to clear off unnecessary data off of your Mac that are safer and you have complete control over your Mac and not just leave a piece of auto cleaning software in charge of clearing off data off of your Mac. Their potential of causing OS X issues outweighs the implied good and benefits these types of hard drive or memory "cleaning" apps are written to do.
These types of system 'cleaning" apps are very poorly written and are really a scam to rob newbie and novice Mac users of their hard earned cash for a poorly written maintenance program that will do much more harm to a perfectly normal running OS X system than the good that the app developers purport these types of apps will do.
Plus, the software companies that write these apps make it hard to easily uninstall these apps if something DOES go wrong and these apps work in a way where you have no recovery or revert function to return your Mac back to its former, working state in the event something does go wrong.
It is best to never, EVER download and install these types of apps.
The risk to your system and important data is too great a risk! -
I want to integrate SMS gateway to Cisco ISE 1.2 and my question is
SMS notifications are supported for Guest self−registration Services ? or it should be done by SponsorI'm not sure I understand the question. Do you want to log in to the Sponsor Portal using AD credentials?
Create an Identity Source Sequence using AD as an Authentication Source. Go to Administration > Identity Management > Identity Source Sequences. Either Edit or +Add a Sequence and choose from the Authentication Sources shown.
Then choose that Identity Source Sequence by going to Administration > Web Portal Management > Settings. Double-click Sponsor from the Left Menu and click Authentication Source. Choose the Identity Source Sequence. Click Save.
I hope this helps.
Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.
Charles Moreton -
Dears,
Greetings , i asked if can deploy H.323 protocol and MGCP protocol in the same gateway using AS5350XM or AS5400XM Voice gateways and 1 TFTP server and 5 call managers 7.1 .
Regards.Thanks Paolo , the customer request to deploye H.323 for PSTN Line and MGCP for FXO "tellular" connection , i dont know order new VGateway or if it available to reduce tender cost deploye both protocols in the same gateway .
thank you for your response -
CUCM 9.1.1 - MGCP gateway won't register to my 2811
Hello
I am trying to add a MGCP gateway on a 2811.
I have configured as per the book, but it is not registering,
here is my Router config:
2811 uptime is 2 hours, 4 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-11.XJ4.bin"
Cisco 2811 (revision 53.50) with 509952K/14336K bytes of memory.
Processor board ID FHK1302F0YV
3 FastEthernet interfaces
24 Serial interfaces
1 Channelized T1/PRI port
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
125440K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
2811#sh run
Building configuration...
Current configuration : 7125 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 2811
boot-start-marker
boot-end-marker
card type t1 0 2
enable secret 5 $1$ax07$1yOFpGS1rHGYm873l9n9q/
no aaa new-model
clock timezone PCLAIRE -5
clock summer-time PCLAIRE recurring
network-clock-participate wic 2
network-clock-select 1 T1 0/2/0
ip cef
no ip dhcp use vrf connected
ip domain name homelab.local
multilink bundle-name authenticated
isdn switch-type primary-ni
voice-card 0
dspfarm
dsp services dspfarm
controller T1 0/2/0
framing esf
linecode b8zs
pri-group timeslots 1-24
description Home_PBX
vlan internal allocation policy ascending
interface FastEthernet0/0/0
description To Home Network$ETH-LAN$
ip address 192.168.15.50 255.255.255.0
duplex auto
speed auto
interface Serial0/2/0:23
description Home_PBX
no ip address
encapsulation ppp
isdn switch-type primary-ni
isdn incoming-voice voice
control-plane
voice-port 0/2/0:23
description Home_PBX
ccm-manager mgcp
ccm-manager config server 192.168.15.11 - THIS IS THE SUBSCRIBER , SHOULD IT BE THE PUBLISHER ?
ccm-manager config
mgcp
gateway
timer receive-rtp 1200
Here is what I get:
2811(config)#do sh ccm-manager
MGCP Domain Name: 2811.homelab.local
Priority Status Host
============================================================
Primary None
First Backup None
Second Backup None
Current active Call Manager: None
Backhaul/Redundant link port: 2428
Failover Interval: 30 seconds
Keepalive Interval: 15 seconds
Last keepalive sent: 09:55:04 PCLAIRE Jan 16 2014 (elapsed time: 02:00:24)
Last MGCP traffic time: 11:34:19 PCLAIRE Jan 16 2014 (elapsed time: 00:21:08)
Last failover time: None
Last switchback time: None
Switchback mode: Graceful
MGCP Fallback mode: Not Selected
Last MGCP Fallback start time: None
Last MGCP Fallback end time: None
MGCP Download Tones: Disabled
Backhaul/Redundant link is down
Configuration Auto-Download Information
=======================================
No configurations downloaded
Current state: Downloading XML file
Configuration Download statistics:
Download Attempted : 1
Download Successful : 1
Download Failed : 0
Configuration Attempted : 0
Configuration Successful : 0
Configuration Failed(Parsing): 0
Configuration Failed(config) : 0
Last config download command:
FAX mode: cisco
Configuration Error History:
2811(config)#
Any help greatly appreciated
John BachmanStill same problem, I have erased all that related to mgcp on my router, to start from scratch
2811(config)#controller T1 0/2/0
2811(config-controller)#pri-group timeslots 1-24 service mgcp
Cannot overwrite no serv type with one. Unconfigure existing configuration and reconfigure
2811(config-controller)#
Where is this error coming from ??
Here is what I want to try:
192.168.15.10 - pub
192.168.15.11 - sub
controller T1 0/2/0
pri-group timeslots 1-24 service mgcp
interface Serial0/0/0:23
isdn bind-l3 ccm-manager
ccm-manager config server 192.168.15.10 192.168.15.11
ccm-manager config
ccm-manager redundant-host 192.168.15.11
ccm-manager mgcp
mgcp
mgcp call-agent 192.168.15.10 service-type mgcp version 0.1 -
Configuring BRI interface for Voice ( MGCP gateway
hi there,
i have a Call Manager which is connect to Cisco 2800 series acting as MGCP getway. ISDN connection between the 2800 and the carrier ( telestra sydney ). the call manager is seeing the gateway and i have configured a numbering plan on the call manager for the phones. the phones can call internally but externally i dont what configuration i should configure under the BRI interface for the carrier ( telestra ) to recongnise my number plan. please if you have any demo configuration or configuration that has perviously used post to me.this is a basic MGCP config on the Gateway on your area
BRI Switchtype Information
BRIs in Australia require no service profile identifiers (SPIDs).
There are two ISDN switch-types that can be used:
basic-net3?Currently the most commonly used.
basic-ts013?For older ISDN switches such as MicroLink.
isdn switch-type basic-net3 or 5
voice-card 2
dspfarm
dsp services dspfarm
controller T1 2/0
description T1 link to SRST
framing esf !--- Automatic method automatically adds
clock source internal
linecode b8zs !--- Automatic method automatically adds
cablelength short 133
pri-group timeslots 1-2,24 service mgcp !--- Automatic method
!--- automatically adds 24 channels.
!---You can manually edit channels.
description T1 link to SRST
interface Serial2/0:23
no ip address
isdn switch-type primary-ni !--- Automatic method automatically adds
isdn protocol-emulate network !--- Simulated Lab ISDN
isdn bind-l3 ccm-manager !--- Allows all Q931 to be backhauled over TCP to
!--- CallManager; automatic method automatically adds
no cdp enable !--- Automatic method automatically adds
ccm-manager mgcp
ccm-manager music-on-hold
ccm-manager config server 171.69.103.225
ccm-manager config !--- Enables automatic config download from CallManager
!--- Automatic method automatically adds these commands
mgcp
mgcp call-agent 171.69.103.225 2427 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
no mgcp package-capability fxr-package
mgcp package-capability pre-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
mgcp rtp payload-type g726r16 static
mgcp profile default -
CUCM 9 & AS5850, Using MGCP Gateways not found in "Gateway Type" list...
I have an application where I need to control a large, AS5850 gateway using MGCP. CUCM version is 9.1, soon to be 10.0. The gateway is populated with CT3 cards.
We have confirmed that the AS5850 does in fact support MGCP, however it is not listed as an option in the list of gateway product choices when adding a new gateway in CUCM. So my first question:
1) How do you add an MGCP gateway in CUCM when it is not listed in the "gateway type" drop-down list? It seems there must be a way to do this. Other well known gateways such as the AS5300, AS5400 etc.. are also notably absent from the list of gateway choices. Perhaps there is a template that can be edited?
If anyone has experience utilizing an AS5850 gateway with CUCM & MGCP, it would be very useful to see sample configuration programming from your gateway.
Many thanksHi,
As per the datasheet, the Cisco AS5850 Universal Gateway supports H.323, SIP, and MGCP call-control protocols with extensive SNMP management and debugging capabilities. It works with the Cisco PGW 2200 Softswitch, the Cisco BTS 10200 Softswitch, and many partner softswitches as well.
http://www.cisco.com/en/US/prod/collateral/iad/ps509/ps512/product_data_sheet09186a008007cc48.html
It looks like that its not supported with CUCM.
HTH
Manish -
Hi All;
I am actually keep asking with my self, why to use gatekeeper or SIP proxy when deploying the CVP solution, why not to use the Call Manager? Is it because that the concept built on SIP and H323 so call manager can not handle these kind of operations as call manager is supporting MGCP?
From the other side, what kind of trunk or protocol of communication method is used between the ingress gateway and the VXML browser?
Any advise?
Regards
BilalThe main reason is not all who deployed ISN/CVP in the past use Call Manager as the PBX.
CVP is a powerful solution that covers many deployment scenarios. Its ability to integrate with legacy switches has been very important in the past, and although as we move forward, these types of deployments will probably become fewer, the independence of CVP on Call Manager remains a cornerstone of the design.
I'm glad it was built that way. Look at some of the other deployment models (like Call Director) in the CVP Guide.
It's not because Call Manager supports MGCP - you don't need to have any MGCP gateways in your Call Manager deployment. You could have all H.323 gateways and manage the dial plan on the gateways with a gatekeeper. Or use SIP.
The ingress gateway does not talk to the VXML server - the VXML gateway does.
In a branch office design, these are one and the same; but that's not the fundamental architecture. The IOS on the VXML gateway runs a voice browser (I guess you could call this a VXML browser). It uses HTTP to send and receive information (VXML documents) from the VXML server - whether this be the CVP Call Server or an external VXML server (like what was brought in-house with the Audium acqusition - the Cisco CVP VXML Server).
Regards,
Geoff -
Cannot register MGCP gateway to CCM 4.1
Hello,
I am running an application which simulates a MGCP gateway vs. a real CCM 4.1. I am not able to register the endpoints as you can see from the snapshot attached. I guess the problems lies in the 200 response to the following AUEP:
AUEP 89 AALN/S0/SU0/[email protected] MGCP 0.1
F: X+SRTP/A
200 89 OK
X: 2
L: p:20, a:PCMU, b:64, e:ON, s:ON
I have also attached the trace file and CCM logs.
I have 2 questions on this matter:
what is the correct format of the 200 message which needs to be sent to AUEP with SRTP?
how can I configure CCM not to sent this AUEP with SRTP(I have a similar one in my setup which is not sending this AUEP)?
Thanks in advanced for you support,
IonutRestrictions for Cisco Multiservice IP-to-IP Gateway Configuration:
Restrictions for SIP-to-SIP Call Signaling:
Transcoding is not supported.
SIP-to-H.323 Call-Signaling Features:
Codec transcoding (G.711-G.729) - supported
other:Transcoding is not supported on the Cisco 7200 and the Cisco 7301
copied from:cisco Multiservice IP-to-IP Gateway
http://www.cisco.com/en/US/products/sw/voicesw/ps5640/products_configuration_guide_book09186a0080409b6d.html
I have not found a solution, but i'd be interested in what you find though. -
MGCP Gateway With ISDN BRI interface
Hi Guys,
I have a voice gateway with a BRI card on slot 0/3/0 (port 0/1) and I wanted to terminate both WAN and PSNT connection to the same gateway with MGCP protocol, and as I'm new to voice over IP world can anyone suggest/recommand me a proper guide which includes the stepts and proper explanations to acheive this task.
Thank you
Regards,
SuthakarHi Aman,
As discussed please find the attached output as follows,
#sh isdn status
Global ISDN Switchtype = basic-net3
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply
ISDN BRI0/0/0 interface
dsl 0, interface ISDN Switchtype = basic-net3
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 1. Layer 3 output may not apply
ISDN BRI0/0/1 interface
dsl 1, interface ISDN Switchtype = basic-net3
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 1 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI0/3/0 interface
dsl 12, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 12 CCBs = 0
The Free Channel Mask: 0x80000003
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 13. Layer 3 output may not apply
ISDN BRI0/3/1 interface
dsl 13, interface ISDN Switchtype = basic-net3
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
ACTIVE
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
--More-- Active dsl 13 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
#sh ccm-manager
MGCP Domain Name: xxxxx.com
Priority Status Host
============================================================
Primary Registered x.x.x.x
First Backup None
Second Backup None
Current active Call Manager: x.x.x.x
Backhaul/Redundant link port: 2428
Failover Interval: 30 seconds
Keepalive Interval: 15 seconds
Last keepalive sent: 11:10:43 AEDST Nov 21 2013 (elapsed time: 00:00:11)
Last MGCP traffic time: 11:10:43 AEDST Nov 21 2013 (elapsed time: 00:00:11)
Last failover time: None
Last switchback time: None
Switchback mode: Graceful
MGCP Fallback mode: Enabled/OFF
Last MGCP Fallback start time: 05:28:32 AEDST Nov 18 2013
Last MGCP Fallback end time: 11:57:01 AEDST Nov 20 2013
MGCP Download Tones: Disabled
TFTP retry count to shut Ports: 2
Backhaul Link info:
Link Protocol: TCP
Remote Port Number: 2428
Remote IP Address: x.x.x.x
Current Link State: OPEN
Statistics:
Packets recvd: 3
Recv failures: 0
Packets xmitted: 5
Xmit failures: 0
BRI Ports being backhauled:
Slot 0, VIC 0, port 1
Slot 0, VIC 0, port 0
Slot 0, VIC 3, port 1
Configuration Auto-Download Information
=======================================
Current version-id: 1384908973-2cefe363-d1ae-423b-a6ef-a85a0d4216af
Last config-downloaded:00:00:00
Current state: Waiting for commands
Configuration Download statistics:
Download Attempted : 6
Download Successful : 3
Download Failed : 1
TFTP Download Failed : 8428
Configuration Attempted : 3
Configuration Successful : 3
Configuration Failed(Parsing): 0
Configuration Failed(config) : 0
Last config download command: New Registration
FAX mode: disable
Configuration Error History:
Regards,
Suthakar -
Integration of Cisco Fax Server with CUCM
Need some help with regards to the setup of Cisco Fax Server. I have Cisco Fax Server 9.4 Enterprise Suite which will be installed on Cisco 7816 server. Now my concern is with the integration of Fax server with CUCM. I have CUCM Ver 7. Could anyone tell me what configuration is required on CUCM and I believe we need to have dial-peer on the Voice gateway as well pointing to the Fax server. If anyone has deployed then please let me know the configuration on CUCM & the voice gateway.
Hi..
Thank u so much guys. I was mostly looking out for the integration of Fax server with CUCM, so i think this document should help. I has this document with me but had few doubts. Hopefully it should be cleared now. I will be doing the implementation later next week so i will keep you updated. Anyway thank u so much once again.
Regards,
Joy
Maybe you are looking for
-
I'm on Mac OS 10.6.8 and on iPhoto 7.1.5. Quick Time no longer opens when I select a video to watch. Nothing happens. Anyone have a solution?
-
Hello SAP Gurus: I have a couple of questions that I came across. Could you please point to where I can get some information on these? How do you perform cash reconciliation? How do you do post processing of Cash Applications? (or what exactly do we
-
Pause key not working whilst recording a video demo.
Hello, The title says it all really. I've set the pause key to various different keys and have then pressed them whilst recording a video demo with narration. On video playback, it is clear that the video recording was not paused at any point. What i
-
Recovering web site from iDisk
I had my hard drive whiped out and long story short I had to buy a new MacBook. The only place I had my web page backed up was on iDisk. I downloaded it to my new macBook but I want to still work on it and get all the pictures back that I put on that
-
G5 crash, need help repairing
G5 that just crashed. Monitor is showing just lines across it. I swithched monitors and had same screen so not a monitor issue. What do I try next?