Mgt interface stuck in init state

I can not connect to my mgt minterface on my mds 9509.
The only thing that looks odd is the mgt interface status. Is this normal?
Interface Status IP Address Speed MTU
mgmt0 init 10.1.1.24/24 100 Mbps 1500
MDS-switch-A# sh int mgmt 0
mgmt0 is down (Initializing)
Hardware is GigabitEthernet
Address is 001a.e203.8af8
Internet address is 10.1.1.26/24
MTU 1500 bytes
0 packets input, 0 bytes
0 multicast frames, 0 compressed
0 input errors, 0 frame, 0 overrun 0 fifo
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 fifo
0 carrier errors

hmm not sure where they 4 came from..but here is the status now..still in init..and here is the config..etc..
Interface Status IP Address Speed MTU
mgmt0 init 10.1.1.26/24 100 Mbps 1500
XP-24000-MDS-switch-A# sh run int mgmt 0
version 3.2(2c)
interface mgmt0
ip address 10.1.1.26 255.255.255.0
XP-24000-MDS-switch-A# sh int mgmt 0
mgmt0 is down (Initializing)
Hardware is GigabitEthernet
Address is 001a.e203.8af8
Internet address is 10.1.1.26/24
MTU 1500 bytes
0 packets input, 0 bytes
0 multicast frames, 0 compressed
0 input errors, 0 frame, 0 overrun 0 fifo
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 fifo
0 carrier errors

Similar Messages

GigE port stuck in init state on SSN-16

I have a Cisco MDS 9222i running NX-OS 6.2(3) with a SSN-16 module in slot 2. One of the GigE ports with an active connection to a FEX remains in the "init" state. Shutting and no shutting the port doesn't change the state. When I move the SFP and cable from the problematic port to another port it comes up immediately. Has anybody heard of this problem?

Hi,
Are you seeing hellos across the link (debug ip ospf hello)? If so, please check the MTU settings on both interfaces and set the OSPF link type (point-to-point).
If there are no OSPF hellos received you have to ask your provider to troubleshoot the problem with you. In principle it should work.
Hope this helps!
Regards, Martin

Lost L3 to 5508 mgt interface ???

I'm sort of stumped.
ETA: I've had a couple other sets of eyes looking at this too. Added L3 & Po config at the bottom.
I've lost L3 to/from the management interface of one of my 5508 WLCs.
Neighbor is a 6509 doing the routing. Connection via port-channel, native vlan is the untagged mgt vlan. Native vlan is HSRP. I have tried setting mgt gateway to real IP rather than standby, no help. I even brought in another 5508 with the same code and loaded this config on it, no help. Console & service port are working fine. I can't ping the default gateway, but I can ping the default gateways of all the dynamic interfaces, which are all on the same 6509. I have to keep 7.0 code until I get rid of all the 1231 APs on this WLC.
All the APs have failed over to a WiSM2 for now, but they keep trying to phone home.
Any ideas?
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.240.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 7.0.112.21
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... WLC9-CT5508-50
System Location.................................. Server Rm Rack2
System Contact................................... 0117
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.17.121.9
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 49 mins 46 secs
Interface Name................................... management
MAC Address...................................... e8:b7:48:9b:27:ef
IP Address....................................... 10.17.121.9
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 10.17.121.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. LAG (13)
Primary Physical Port............................ LAG (13)
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 10.192.146.38
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Disabled
CDP neigh
Device ID: 2ND-6509-SW1.@@@.@@@.@@@
Entry address(es): 10.17.121.2
Platform: cisco WS-C6509-V-E, Capabilities: Router Switch IGMP
Interface: GigabitEthernet0/0/1, Port ID (outgoing port): GigabitEthernet8/47
Holdtime : 138 sec
Version :
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9-M), Version 15.1(1)SY1, RELEASE SOFTWARE (fc5) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc. Compiled Wed 01-May-13 13:16 by prod_rel_te
Advertisement version: 2
Duplex: Full
Device ID: 2ND-6509-SW1.@@@.@@@.@@@
Entry address(es): 10.17.121.2
Platform: cisco WS-C6509-V-E, Capabilities: Router Switch IGMP
Interface: GigabitEthernet0/0/2, Port ID (outgoing port): GigabitEthernet3/47
Holdtime : 159 sec
Version :
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9-M), Version 15.1(1)SY1, RELEASE SOFTWARE (fc5) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2013 by Cisco Systems, Inc. Compiled Wed 01-May-13 13:16 by prod_rel_te
--More-- or (q)uit
Advertisement version: 2
Duplex: Full
interface Vlan2
description Management Segment
ip address 10.17.121.2 255.255.255.0
ip helper-address 10.192.146.38
ip helper-address 10.96.40.38
no ip redirects
no ip proxy-arp
ip flow ingress
ip flow egress
standby version 2
standby 2 ip 10.17.121.1
standby 2 timers 1 4
standby 2 priority 150
standby 2 preempt delay minimum 600 reload 1800
standby 2 authentication md5 key-string 7 046D070701736A4F00150A011719
standby 2 track 1 decrement 10
load-interval 30
interface Port-channel2
description Po2 to OLDWLC-CT5508-50 via g3/47 & g8/47
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 2
switchport trunk allowed vlan 2,113,115,190
switchport trunk pruning vlan none
switchport mode trunk
switchport nonegotiate
load-interval 30
spanning-tree portfast edge trunk
spanning-tree bpduguard disable
end interface Vlan2
description Management Segment
ip address 10.17.121.2 255.255.255.0
ip helper-address 10.192.146.38
ip helper-address 10.96.40.38
no ip redirects
no ip proxy-arp
ip flow ingress
ip flow egress
standby version 2
standby 2 ip 10.17.121.1
standby 2 timers 1 4
standby 2 priority 150
standby 2 preempt delay minimum 600 reload 1800
standby 2 authentication md5 key-string 7 046D070701736A4F00150A011719
standby 2 track 1 decrement 10
load-interval 30
interface Port-channel2
description Po2 to OLDWLC-CT5508-50 via g3/47 & g8/47
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 2
switchport trunk allowed vlan 2,113,115,190
switchport trunk pruning vlan none
switchport mode trunk
switchport nonegotiate
load-interval 30
spanning-tree portfast edge trunk
spanning-tree bpduguard disable
end

I'll tag the mgt interface and remove native from the vlan. I just have to drive across town to do it.
Controller should still be in LAG mode. I'll verify when I get there.
Doesn't look like "vlan dot1q tag native" command is enabled. That would be contrary to our standards.
2ND-6509-SW1#sh run | i tag native
2ND-6509-SW1#sh run | i vlan dot1q
2ND-6509-SW1#
2ND-6509-SW1#sh int po2
Port-channel2 is up, line protocol is up (connected)
Hardware is EtherChannel, address is d0d0.fd18.b8de (bia d0d0.fd18.b8de)
Description: Po2 to OLDFED-CT5508-50 via g3/47 & g8/47
MTU 1500 bytes, BW 2000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is unknown
input flow-control is off, output flow-control is off
Members in this channel: Gi3/47 Gi8/47
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 2000 bits/sec, 3 packets/sec
30 second output rate 4000 bits/sec, 4 packets/sec
     123176 packets input, 36255790 bytes, 0 no buffer
     Received 46791 broadcasts (3427 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     297242 packets output, 31071016 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
2ND-6509-SW1#sh int g3/47
GigabitEthernet3/47 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is d0d0.fd19.7c8e (bia d0d0.fd19.7c8e)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseT
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:02, output 00:00:26, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 0 bits/sec, 0 packets/sec
30 second output rate 1000 bits/sec, 2 packets/sec
     25220 packets input, 2359978 bytes, 0 no buffer
     Received 2286 broadcasts (2284 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 3 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     141556 packets output, 11328907 bytes, 0 underruns
     0 output errors, 0 collisions, 5 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
2ND-6509-SW1#sh int g8/47
GigabitEthernet8/47 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is d0d0.fd18.b8de (bia d0d0.fd18.b8de)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseT
input flow-control is off, output flow-control is off
Clock mode is auto
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:05, output 00:00:06, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 1000 bits/sec, 2 packets/sec
30 second output rate 1000 bits/sec, 2 packets/sec
     97934 packets input, 33893620 bytes, 0 no buffer
     Received 44504 broadcasts (1142 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 3 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     0 input packets with dribble condition detected
     155643 packets output, 19736281 bytes, 0 underruns
     0 output errors, 0 collisions, 5 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out
2ND-6509-SW1#

Workflow stuck in starting state after applying SharePoint 2010 CU December 2012

I have custom visual studio workflow which are associated with Custom content type. workflow gets triggered automatically when a file is uploaded to SharePoint. Everything was working fine till when i apply the following CU
http://blogs.msdn.com/b/joerg_sinemus/archive/2012/12/27/sharepoint-2010-and-december-2012-cu.aspx
After applying this my workflow get stuck in "Starting" state.
No error were logged in 14 hive logs.
Thanks in Advance!

It took me a while but I came up with a work around. There is a PowerShell script below that can be used to trigger the workflow. Hopefully this will hold all of us over until the official fix arrives.
First remove the auto start on change or new from the affected workflow
Edit the script below to match your environment
Add the script to Windows task scheduler with the PowerShell.exe in the command line
This assumes PowerShell.exe is in the path
Then add the full path and script name in the add arguements text box
Script:
#The purpose of this script is to start the SPD workflow with the windows task scheduler for a trigger
#This should avoid the check in-out issue caused by the December 2012 SP CU patch
#This needs to be run on an account with membership in the farm administration group for SharePoint and Shell in SQL
#You can use a find and replace to replace the server and other names with your actual names
#There are no status messages being used since this will be a scheduled task in the Windows task scheduler
#Add SharePoint modules and create variable space
add-pssnapin microsoft.sharepoint.powershell
start-spassignment -global
#Open the web site, list and the workflow
$site=get-spsite %site url%"
$web=get-spweb %Web url%
#Open the %affected% library or list and workflow association
$%affected%=$web.getlist("%affected%")
$manager=$site.workflowmanager
$culture=[system.globalization.cultureinfo]::currentculture
$wfname="%affected workflow name"
$association=$%affected%.workflowassociations.getassociationbyname($wfname,$culture)
$data=$association.associationdata
$wfrunoption=[microsoft.sharepoint.workflow.spworkflowrunoptions]::synchronous
#Start workflow
foreach ($item in $%affected%.items) {
$site.workflowmanager.startworkflow($item,$association,$data,$wfrunoption)
stop-spassignment -global

Agent get stucked in Reserved State

HI CUCCE gurus,
Need assistance on this issue. In our remote office, our Sales Team has a linegroup setup, the Sales extensions are part of the linegroup and at the same time its their ACD line when they logged in to Cisco Agent Desktop.
The issue is, when they got a call from the linegroup their CAD state change to "Reserved" and it stuck from that state and nothing they can do to change the state but to logoff, close the apps and log back in.
I enabled debug on once of the Sales CAD (see attached output).
Any troubleshooting tips that you can advise or detailed steps to check from our system.
Our CAD is 7.X
Our CUCCE is 7.X
Our CUCM 7.X
Thank you.

Hi Jhun,
Agent stuck in reserved state it means, the ICM has reserved the agent, but the call is not getting delivered to the agent extension.
If you are using SIP trunk, you would probably need to check the CSS and Partitions over the trunk. Also, any recent changes made on the CSS of the SIP trunk you would need to reset the SIP trunk.
The CSS on the SIP trunk should contain the partition of the phone.
Also, you would need to check on the Agent targetting rule in the config manager of the ICM. The agent extensions should be added to the Agent targetting rule
Hope this helps!!!
Cheers,
Dass
Please rate useful posts

I have a set of 3 USB disk connected to my TC via a USB hud. I usually swithc the TC at night. When I restart the next day it stucks in amber state. when I disconnect the USB hub where my discs connects and restart, it start properly. Any hints?

I have a set of 3 USB disks connected to my Time capsule (TC) via a USB hub. I usually switch the TC at night. When I restart the next day it stucks in amber state. When I disconnect the USB hub where my discs connects and restart, the TC will start properly. Any hints?

LOL.. don't switch off the TC.. this is fairly typical behaviour..
Or try a different usb hub.. but you could well and truly run out of hubs before you fix the problem.
Are you running latest firmware for your TC?
What error message is coming up in the airport utility.. amber led is a fault indicator.. look up what the actual fault is and see if it is for instance overloading the usb. You are using a powered hub??
Get one bigger USB hard disk instead of 3 smaller ones.

Content Switching Module (CSM): Sessions stuck in closing state

Hi guys,
I'm troubleshooting a CSM with 4.3(1).
We migrated a real server from windows to linux, since then lot's of sessions stuck in closing state until the idle timer expires.
I traced the traffic from the client to the csm and from the csm to the real server what I saw is the following behaviour at the end of a session:
windows real server: client sends FIN -> real server acks the FIN -> real server sends FIN -> client sends RST -> real server sends RST -> CSM deletes session from session table
The linux real server mostly behaves like the windows real server but sometimes behaves as follows:
client sends FIN -> real server sends FIN, but does not ack the FIN sequence number of the client -> real server sends RST -> client sends RST -> CSM does not delete session from session table, it stucks in closing state
Does anybody know how I can solve this problem of half-closed sessions other than decreasing the idle timeout?
Is it possible to configure CSM to close and delete sessions not only on FIN-ACK packets but also on RST packets?
Or to use a different fast idle timeout when sessions are half-closed?
Many thanks in advance,
Thorsten

Hi Fabrizio,
CSM_FAST_FIN_TIMEOUT is already set to 10 seconds.
What I found out while testing is that CSM_FAST_FIN_TIMEOUT works with configurations where idle timeout is configured > 0.
But when idle timeout is configured to 0 (what meas no idle timeout) the csm seems not to use CSM_FAST_FIN_TIMEOUT: Half closed sessions will stuck in closing state.
Any idea why cms behaves this way?
Regards,
Thorsten

Workflows stuck in "Starting" state.

Workflows have been running fine for awhile. All workflows are currently stuck in a "Starting" state. Was finally able to capture this in ULS
03/20/2014 11:58:23.46 w3wp.exe (0x15AC)                       0x2A98 SharePoint Foundation
Workflow Infrastructure       72fv Unexpected AutoStart Workflow: System.ArgumentException: Value does not fall within the expected range.     at Microsoft.SharePoint.Workflow.SPWorkflowActivationProperties..ctor(SPWorkflow
workflow, String initiationData, Object context)     at Microsoft.SharePoint.Workflow.SPWorkflowManager.StartWorkflowElev(Object context, SPWorkflowAssociation association, DateTime elevationTimeUtc, SPWorkflowEvent startEvent, SPWorkflowRunOptions
runOptions)     at Microsoft.SharePoint.Workflow.SPWorkflowAutostartEventReceiver.<>c__DisplayClass1.<AutoStartWorkflow>b__0(SPSite superUserSite, SPWeb superUserWeb)
Any ideas?
TIA

Hi Milo,
Please check whether you have installed any CUs for SharePoint 2010.
Please install June 2013 CU or higher for SharePoint 2010, compare the result.
Here are some similar posts for you to take a look at:
http://blogs.msdn.com/b/chaun/archive/2013/05/16/if-your-sp2010-workflows-are-stuck-in-the-starting-state.aspx
http://social.technet.microsoft.com/Forums/sharepoint/en-US/5a6e6e83-b59f-4099-a86f-a07723ff2b98/workflow-stuck-in-starting-state-after-applying-sharepoint-2010-cu-december-2012?forum=sharepointadminprevious
I hope this helps.
Thanks,
Wendy
Wendy Li
TechNet Community Support

Inbound Interface for Accepting Bank Statement Through EDI

Hi All ,
Pls Help me out to complete this Scenerio with u r Ideas and Inputs .
Inbound Interface for Accepting Bank Statement Through EDI.
Rgds
Rafi .

Hi,
INBOUND:
Step 1. EDI Subsystem creates an IDoc file from EDI Messages
2. Subsystem calls Functional Module EDI_DATA_INCOMING from startRFC program.
3. Data in Control Record is validate against the Partner Profile.
4. IDoc is generated in Database and syntax check is carried out.
5. IDoc file is deleted once file read.
6. Event PROCESSSTATE REACHED is triggered in Idoc Object Workflow.
7. Check for Process Immediately.
If NO
Execute RBDAPP01 Program
Else
Read Process Code from Partner Profile
Process Code Points to Function Module
Application Document Posted.
further help:
check url
http://www.sappoint.com/abap/ale.pdf
http://www.sappoint.com/abap/ale2.pdf
http://www.sapgenie.com/ale/configuration.htm
http://www.sappoint.com/abap/ale.pdf
http://www.sappoint.com/abap/ale2.pdf
http://www.sapdevelopment.co.uk/training

[SOLVED] Mailbox import requests stuck in 'queued' state

We have a small Exchange 2013 environment with one server having all roles. I try to import archive mailboxes from an Exchange 2010 environment. It has worked quite well for a while. However, all import requests are now 'stuck' in 'queued' state. Restart
of Replication service, transport service and even server reboot didn't help.
When I run
get-mailboximportrequest | Get-MailboxImportRequestStatistics -Includereport | fl
I observe that PositionInQueue value tells me that there are 85 import requests waiting :
ItemsTransferred                       :
PercentComplete                        : 0
CompletedRequestAgeLimit               : 30.00:00:00
PositionInQueue                        : 85/90 (Position/Queue Length)
InternalFlags                          : None
FailureCode                            :
There should be no requests waiting as I removed all requests in advance before I issued new import requests:
get-mailboximportrequest | Remove-MailboxImportRequest
How can I really reset an import queue by zeroing PositionInQueue ?
Any suggestions/tips?

Hi,
Glade to hear the good news. Thanks for your update.
Best regards,
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Belinda Ma
TechNet Community Support

Ciscoworks daemon manager stuck at Stopping state

I am working on LMS 3.2 . Tried to stop the daemon service with " net stop crmdmgtd ". It stuck on stopping state since few hours now. I can still open the application. Need a suggestion to terminate the previous command and restart the
daemon service.

You should have dmgtd.exe process in Task Manager stuck.
Although you can kill it directly and then try the stop command once again before starting. But to be sure if any process in not stuck, best way would be to reboot the server once.

VM got stuck in "stopping" state, and cannot be stopped

Dear all,
I am using Oracle VM 3.2.2.
One of my VM got stuck in "stopping" state, and cannot be stopped.
How can I troubleshoot this problem...

Q: Is the VM still running, i.e. can you ssh to the VM?
Q: Find the server where the VM is running, and restart the ovs-agent, i.e. "service ovs-agent restart". Did this help, or is the agent crashed, any zombies?
Possible root cause: These type of errors are typically ovs-agent bugs. First update oracle vm manager to the 3.2.4 release, not 3.2.6. Next update the dom0s to 3.2.4, not 3.2.6. You may need to setup a ULN 3.2.4 yum repo to update the dom0s. As you can see in these forms, 3.2.6 is may not ready for prime time, stick with 3.2.4, is stable.

Azure Cloud Service Stuck in "Stopping" state for a long time (12 hours)

Does anyone have suggestions what to do with the issue I have. I tried to stop my Cloud Service the service is now basically stuck in "Stopping" State and been there over 12 hours. In my Cloud service there is 16 Virtual Machines I am using in
testing.
I tried to start Cloud Service but it also failed with error "Could not start the virtual machine deployment.".
Is there something I could do or some way to get Microsoft Support (without paying extra)? I have "Visual Studio Premium with MSDN" so i have no other support but billing from Microsoft :(

Managed to find the solution. I stopped and deallocated all the Virtual Machines. After that the Cloud Service status changed to stopped state. After that it was possible to start the Cloud Service again.

SQL Azure Data Sync stuck in Processing State since 5 Sep 2014

Hi,
I've a sync group stuck in "processing" state since 5 Sep 2014, have tried to restart the client PC, restarted the sync service and also tried to regenerate the sync agent key, but still in vain. Would anyone please help me to figure it out what's
the problem? As I have many sync groups running without any problem for more than a year and encountered this problem recently (in this 3 months).
Here's the sync group details:
Sync Group Name
ew_sync_a054
Status
Processing
LAST SYNC
9/5/2014 5:57:35 PM
Sync Group ID
94f34eaa-cf1c-4af0-950e-7aa565ccc781_East Asia
Location
East Asia
Subscription Name
Solo Customer Batch 2
Subscription ID
cda925fa-16c4-44b6-b3dc-8fc0cb82ad07
Conflict Resolution
Client Wins
Thanks for your help.
Best regards,
Michael Yung

Hi Bowen,
I've checked the local agent has been offline at 2014/09/05 18:00:00 UTC+8, as the shop close every night and they will shut down the computer, but they've turned on the computer in next day morning, and they keep turning that off at night, turn
back on at next morning.
I've checked the agent was online during that "stuck" period when the computer was turned on, as I could click the "PING SYNC SERVICE" and it reported it could reach the sync server, and I could also view from the portal that the agent
was online, just the sync group stuck in the "processing" status.
Best regards,
Michael Yung

SQL Azure Data Sync stuck in Processing State since 14 Sep 2014

Hi,
I've a sync group stuck in "processing" state since 14 Sep 2014, have tried to restart the client PC, restarted the sync service and also tried to regenerate the sync agent key, but still in vain. Would anyone please help me to figure it out what's
the problem? This problem happened across my sync group very frequent recently (they're located in different physical locations), but still no workaround or the root cause :(
Here's the sync group details:
Sync group name: ew_sync_a069
Status
Processing
LAST SYNC
9/14/2014 11:11:22 PM
Sync Group ID
4a604aad-e318-469d-adde-9ed4e1d52ead_East Asia
Location
East Asia
Subscription Name
Solo Customer Batch 3
Subscription ID
a68811f9-f82a-4e7c-b93c-d1bee226f84b
Conflict Resolution
Client Wins
Thanks
for your help.
Best regards,
Michael Yung

As the client need the sync to be fixed ASAP, cannot wait for the answer / help, I've removed the sync agent, compare the data (what data need to download from Azure to client, what data need to upload from client to Azure) and recreate back the sync group.
Hi Micheal,
Is this the workaround in your scenario? Since the Azure SQL Data Sync failed, the Microsoft support engineer will help to solve the problem from backend based on your subscription ID and Sync Group ID. Sometime delay might be expected. Your patience is
greatly appreciated. Thank you for your understanding and support.
Regards,
Charlie Liao
TechNet Community Support

Mgt interface stuck in init state

Similar Messages

Maybe you are looking for