Mib for reading/setting RF channel on standalone Access Points

Hei Everybody. Does anybody know if there is a SNMP mib sfor reading/setting RF channel and other RF-parameters on 1131AG standalone Accesspoints. In my network we are using the "least congested frequency" choice for Channel selection and wants to se what the result for this is.
Regards, Roy

"Least Congested Frequency" does not work.... either set your AP's to a specific channel or only highlight channels 1, 6, or 11. You can use a mib browser to seethe mib listing... this link migh help... son't know if its different from the 1131AG:
http://www.oidview.com/mibs/9/CISCO-DOT11-IF-MIB.html

Similar Messages

Setting wireless router as an access point

I'm trying to set up a wireless router as an access point for a wired router. The wired portion of the network is fine and the internet connection is working. The laptop sees the wireless router and can log in to it. However, the wireless router does not receive an internet connection and cannot "see" the wired portion of the network. I cannot log into the wireless router from one of the wired computers.
Below are the settings I'm using:
Wired router--Linksys BEFSR41v3
Obtain ID Automatically
192.168.0.1
255.255.255.0
Local DHCP enabled
Start # 192.168.0.100
RIP Disabled
UPnP off
Wirless router--Linksys WRT54GS
Automatic Conifguration DHCP
192.168.0.2
255.255.255.0
DHCP Server off
Firewall/NAT off
UPnP off
Set to Router function (rather than Gateway)
I have had to set the laptop to a static IP, since it keeps revereting to a default IP. It is set to 192.168.0.102, 255.255.255.0, Gateway=192.168.0.1, DNS=192.168.0.1
Any suggestions would be welcome.
Thanks
Solved!
Go to Solution.

As you have Disabled the DHCP Server on the Router and the Changed the IP on the Router to 192.168.0.2. the only thing remaining is the Connection part that is you need the Connect the BEFSR41 router from the Number one port to the Number one of WRT54GS that should Work. Please remove the Static IP Address from the Computers.

Setting time on 1130AG series Access Point

I noticed on one of my clients AP's which is an 1130AG series that it had a setting for SNTP. I was a little surprised that it did not have the capability to use regular NTP.
The SNTP servers configured for the AP were two Cisco routers.
Is this a common configuration? Is there a way to upgrade so that the AP's can use NTP?
The current code on the AP is 12.3(8)JA.
Thanks
Kevin

Hi Kevin,
The commands for this changed from NTP to SNTP somewhere in the 12.2.x releases, so "older" AP IOS's did support NTP. Here is some info for 12.3.(4)JA;
Managing the System Time and Date
You can manage the system time and date on the wireless device automatically, using the Simple Network Time Protocol (SNTP), or manually, by setting the time and date on the wireless device.
Simple Network Time Protocol (SNTP) is a simplified, client-only version of NTP. SNTP can only receive the time from NTP servers; it cannot be used to provide time services to other systems. SNTP typically provides time within 100 milliseconds of the accurate time, but it does not provide the complex filtering and statistical mechanisms of NTP.
You can configure SNTP to request and accept packets from configured servers or to accept NTP broadcast packets from any source. When multiple sources are sending NTP packets, the server with the best stratum is selected.
If multiple servers are at the same stratum, a configured server is preferred over a broadcast server. If multiple servers pass both tests, the first one to send a time packet is selected. SNTP will only choose a new server if it stops receiving packets from the currently selected server, or if a better server (according to the above criteria) is discovered.
Configuring SNTP
SNTP is disabled by default. To enable SNTP on the access point, use one or both of these commands in global configuration mode:
sntp server {address | hostname}
[version number]
Configures SNTP to request NTP packets from an NTP server.
sntp broadcast client
Configures SNTP to accept NTP packets from any NTP broadcast server
Enter the sntp server command once for each NTP server. The NTP servers must be configured to respond to the SNTP messages from the access point.
If you enter both the sntp server command and the sntp broadcast client command, the access point will accept time from a broadcast server but prefers time from a configured server, assuming the strata are equal. To display information about SNTP, use the show sntp EXEC command.
Hope this helps!
Rob

Setting up Time Capsule as "Access Point" and not using router feature

I would like to use my Time Capsule as a wireless access point for a laptop. What settings in Airport Utility do I need to make?
Here's my setup:
Internet -> DSL Modem -> Linksys (wired) router -> Ethernet Switch -> Time Capsule.
Connect Using: Ethernet
Configure IPv4: Manually
IP address: 192.168.1.20
Subnet: 255.255.255.0
Router: 192.168.8.1
Connection Sharing: Off - Bridge Mode

Follow up to my question.
Got my laptop to access the internet via the Time Capsule. How? By having my ethernet switch connected to the WAN port of the Time Capsule - not the LAN port.
Internet ->DSL Modem -> Ethernet Switch -> Time Capsule (WAN port)
I noticed that makes it so computers on my wired LAN can't use 'Airport Utility' to access the Time Capsule. I have to move the ethernet cable from the ethernet switch to a Time Capsule LAN port, in order for my wired LAN computers to see my Time Capsule.
Is there a way, so I don't have to unplug from the Time Capsule WAN - to LAN port?

Accept client according to their RSSI power in standalone access point

I want to only allow users that are near access point with high RSSI power and force other users with low RSSI power to connect to other nearest AP to them
I am using standalone AP 1130g

You can changed the data rates but that's global. You can disable the lower data rates on a given access point that only allows devices that can associate at 48mbps or 54mbps. If you want.
Here is a link that explains the data rates in an autonomous AP.
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b-chap6-radio.html#wp1101903
Sent from Cisco Technical Support iPhone App

Standalone access points(FAT) as mesh APs -1602

Hi,
We have a group of fat access-points in the network. Do you know whether 1602 series access-points can act as mesh access-points without a controller?
thanks,
Ramesh

I don't know if they can or not since its not shown in this v7.6 guide:
http://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/7-6/design/guide/mesh76/mesh76_preface_00.html
Here is a guide regarding indoor mesh, so you get a good understanding of what it can and can't do.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-mesh/111451-indoor-mesh-deploy-guide-00.html
Thanks,
Scott
*****Help out other by using the rating system and marking answered questions as "Answered"*****

Export using Compressor for DTV setting (7 channel audio)

I am trying to export a FCP project using Compressor - I have 8 channels of audio - to make up L, R, C, FLE, Ls, Rs,Lt, Rt. I am exporting ProRes 422 HQ with the SMTP DTV Audio setting. At the end of the export, I have been dragging the file into soundtrack to check the audio output, and there is only info on the first two channels of the 8-channel audio track.
The sequence settings are set as discrete channels. What am I missing?

And then, you feel like an eejit when you realize that you forgot to assign the channels in the timeline....

Specific OID for A radio modules on 1200 series access points

Is there a specific OID for A radio module cards of the following type:
Flap - AIR-RM21A-A-K9
Dipoles - AIR-RM22A-A-K9

No switches in Cisco's current product line provide enough power to support both radio modules in the 1200 series. The (now optional) power injector for the 1200 will provide enough inline power for both radios, if that is an acceptible option.
Cisco has plans for several switches that will be able to provide inline power to both radios, but I am not aware of ETA's on these.

Open file for reading and allow access by others

How can I open a file for reading and still allow others to access (read and write) the file? I plan to keep this file open for the duration of my program and close it at the end. However while my program is running another program will need access to the file so it can write to it. I may be wrong, but I dont think that setting the appropriate permission will solve the problem... Thank you for your time.
Cheers!
CLA, CLED, CTD,CPI, LabVIEW Champion
Platinum Alliance Partner
Senior Engineer
Using LV 2013, 2012
Don't forget Kudos for Good Answers, and Mark a solution if your problem is solved.

hi jmcbee,
I think as long as "readers" open a file as "ReadOnly", then the OS (at least Windows) will allow another process to open and write to the same file without a problem. It's been a while since I've done this - maybe 7 years - and I may have opened the "writer" first, though doubt it makes a difference.
Have you tried?
Cheers!
"Inside every large program is a small program struggling to get out." (attributed to Tony Hoare)

Mail for Exchange - Access Point question

Hello,
When setting up Mail for Exchange, you need to input the Access Point. I cannot find an option to select "Ask for Access Point" or something along that line.
I use wireless access points and when I go from one spot to another I have to change my settings just to sync.
Does anyone know of an option, if not how could I file for a feature request?

The specific problem can be resolved. How did you hard reset your phone? You should hard reset your phone (some key combination which I cannot remember, press four keys simultaneously). Then format mass memory. Reinstall the firmware. Otherwise let Nokia Care reflash your phone. I had issues with freezes when I hung up a call, but that was resolved when Nokia Care reflashed my phone.
My phone is currently broken, so I cannot help you further.
Erik

Mac-adress list of manufacturers only for access points

hello,
i'm going to look for forbidden access points at the ports of huge network. is there any document that can show me whether a mac adress is an access point or not ?

If you want to do rogue access point detection then you have a few options:
1. Scan suspected ranges for port 80 servers as almost every access point has web-based configuration.
2. Cisco has provided a list of vendor mac address who make Access Points.
This list is found in their
"SAFE: Wireless LAN Security in Depth - version 2"
whitepaper
Check the link
"http://www.cisco.com/en/US/products/hw/wireless/ps430/products_white_paper09186a008009c8b3.shtml"
The list is at the very bottom of the whitepaper
"Table C-7 MAC OUIs Used by Access Point Vendors"
"Table C-7 provides a partial list of MAC OUIs used by access point vendors. This table was obtained from the aptools site at aptools.sourceforge.net."

Open data set for reading excel file on application server in back ground

open data set for reading excel file on application server in back ground

hi Vijay,
I am afraid you won't be able to read from Excel file on Appl. Server.
ec

I updated Itunes today to the latest version. Windows 7 64bit. None of my drivers work and get an error when itunes starts, about registry setting for reading and writing dvds and cds missing. Anyone else have the same issue. I downloaded itunes again, re

I updated Itunes today to the latest version. Windows 7 64bit. None of my drivers work and get an error when itunes starts, about registry setting for reading and writing dvds and cds missing. Anyone else have the same issue. I downloaded itunes again, reinstalled still have same issue.

I'd start with the following document, with one modification. At step 12 after typing GEARAspiWDM press the Enter/Return key once prior to clicking OK. (Pressing Return adds a carriage return in the field and is important.)
iTunes for Windows: "Registry settings" warning when opening iTunes

Workaround for Reader 10.1.2 print "Duplex setting/Printer Blinking/Paper Tray" issue

Dear users,
We have been receiving feedbacks from our users related to the recent "Duplex setting/Printer Blinking/Paper Tray" problems faced.
A lot of these issues have been faced due to introduction of "Print on Both sides" setting right on the Print Dialog in order to help our users set this option without having to go to the printer properties dialog. However, we have made this option as default ON and hence users have reported problems described above.
Thus, we request you to please try unchecking this setting to OFF state and then print to see if that resolves the problem faced.
Thanks,
Atul Agarwal
Adobe Systems

You can easyly solve this with the following procedure:
Open your Windows Group Policy Editor, chose "New Group Policy", go to UserConfiguration->Settings->Windows Settings->Registry. Right click "Registry", chose "new-> registry assistent", local computer, go to
[HKEY_CURRENT_USER\Software\Adobe\Acrobat Reader\10.0\AVGeneral]
"iDuplexMode"=dword:00000002
(mark only "iDuplexMode" !)
and click "finish".
Doubleclick that new entry down till you see "iDuplexMode", double click it too, and change the REG_DWORD value into "1" (decimal). At the very top I also chose "replace" under "action" (not sure if really needed)
Close the GPO editor and link that newly create group policy to you domain or OU or whatever.
You can make a "gpupdate /force"at a client to see the reg entry changing from "2" (= dublex) to "1" (=non duplex).
Reboot your clients or just wait your personal "gpupdate time period".
Thanks Adobe for that setting!
BTW: You can also config that with the "Adobe Customization Wizard X" and save it in a .mst file to roll out your installation with Active Directory software distribution or your favorite tool. Unfortunatly - as it is an entry in HKEY_CURRENT_USER - this hive is only load after log in and it is not present during bootup installation, so your setting gets lost.
You can do the same for Adobe Acrobat X, if you need. The Key is:
HKEY_CURRENT_USER\Software\Adobe\Acrobat\10.0\AVGeneral]
"iDuplexMode"=dword:00000002

Tips for dealing with large channel count on cRio

Hello, I have a very simple application that takes an analog input using an AI module (9205) from a thermistor and based on the value of the input it sends out a true/false signal using a digital out module (9477). Each cRio chassis will have close to 128 channels, the code being exactly the same for each channel.
I wonder if anyone has any tips for how I can do this so that I don't have to copy and paste each section of code 128 times. Obviously this would be a nightmare if the code ever had to be changed. I'm sure there is a way to make a function or a class but being new to graphical programming I can't think of a good way to do this. I looked for a way to dynamically select a channel but can't seem to find anything, if I could select the channel dynamically I'm guessing I can create a subvi and do it that way. Any tips or help would be greatly appreciated.

There isn't a way to dynamically choose a channel at runtime. In order
for the VI to compile successfully, the compiler must be able to statically
determine which channel is being read or written in the I/O Node at
compile time. However, that doesn't mean you can't write a reusable
subvi. If you right click on the FPGA I/O In terminal of the I/O Node and create a constant or control, you should be able to reuse the same logic for all of your channels. The attached screen shot should illustrate the basics of what this might look like. If you right click the I/O control/constant and select "Configure I/O Type...", you can configure the interface the I/O Item must support in order for it to be selectable from the control. While this helps single source some of the logic, you will still eventually need 128 I/O constants somewhere in your FPGA VI hierarchy.
I should also mention that if each channel being read from the 9205 is contained in a separate subVI or I/O Node, you will also incur some execution time overhead due to the scanning nature of the module. You mentioned you are reading temperature signals so the additional execution time may not be that important to you. If it is, you may want to look at the IO Sample Method. You can find more information and examples on how to use this method in the LV help. Using the IO Sample Method does allow you to dynamically choose a channel at runtime and is generally more efficient for high channel counts. However, it's also a lot more complicated to use than the I/O Node.
You also mentioned concerns about the size of arrays and the performance implications of using a single for loop to iterate across your data set. That's the classic design trade off when dealing with FPGAs. If you want to perform as much in parallel as possible, you'll need to store all 128 data points from the 9205 modules at once, process the data in parallel using 128 instances of the same circuit, and then output a digital value based on the result. If you're using fixed point data types, that's 182 x 26 bits for just the I/O data from the 9205. While this will yield the fastest execution times, the resulting VI may be too large to fit on your target. Conversely, you could use the IO Sample Method to read each channel one at a time, process the data using the same circuit, and then output a digital value. This strategy will use the least amount of logic on the FPGA but will also take the longest to execute. Of course, there are all sorts of options you could create in between these two extremes. Without knowing more about your requirements, it's hard to advise which end of the spectrum you should shoot for. Anyway, hopefully this will give you some ideas on where to get started.
Attachments:
IO Constant.JPG ‏31 KB

Mib for reading/setting RF channel on standalone Access Points

Similar Messages

Maybe you are looking for