MICR printer configuration

Hi All,
I am trying to configure my check printer to print MICR characters.
Thr printer which we are using is HP Laser Jet P2015 printer.
The configurations are done as per Note: 94233.
Following are the inputs which are given by me in SPAD transaction.
DEvice Type: ZTROYMIC : TROY MIC Printer
Access Method: G
Host Printer :
<Network Pah of Printer>
Please do help me and let me know if there is anything else that is pending from my end.
Regards,
Nitin

Nitin,
SAP does not support printer P2015 for printing MICR characters.Following are the only printer models you can use with the device type TROYMICR.
Printer model:      TROY MICR printer   TROY MICR fonts+toner
HP LaserJet 4P                          X
HP LaserJet 4        TROY 508            X
HP LaserJet 4 Plus   TROY 512            X
HP LaserJet 4 V                          X
HP LaserJet 4 SI                        X
HP LaserJet 5P                          X
HP LaserJet 5        TROY 512 Plus       X
HP LaserJet 5 SI                        X
HP LaserJet 5SI (mopier)                X
HP LaserJet 6P                          X
HP LaserJet 1000                        X
HP LaserJet 1100     TROY 1100          X
HP LaserJet 1200     TROY 1200          X
HP LaserJet 2100     TROY 2100          X
HP LaserJet 2200     TROY 2200          X
HP LaserJet 4000     TROY 617            X
HP LaserJet 4050     TROY 4050          X
HP LaserJet 4100     TROY 4100          X
HP LaserJet 4200     TROY 4200          X
Hope this is clear to you now.

Similar Messages

How to avoid print configuration screen

Hi everybody,
I'm executing a program which has to print two smartforms, one followed by the other, but I don't want the printing configuration screen before printing each one, I want it only to appear in the first one and then inherit printing parameters in the next smartform and avoid the screen.
How can I do this? I think that is by using output_options parameter but I don't know exactly how.
Many thanks,
Cristina.

hi,
I understand that you have your own program that triggers both Smartforms, one after the other, right?
Try this:
In your program trigger the first smartform (and have the print config screen popup)
WITHIN that smartform you trigger the second Smartform and suppress the the config screen.
Since the output options are know at this point you can pass them to the second smartform.
I hope it helps,
regards,
Joris Bots

ORARRP doesn't print to a printer configured through TCP/IP.

Could any one using ORARRP pls. help ? I am pasting the TAR contents I opened with Oracle Support.
Oracle Support doesn't support ORARRP. They referred me back to discussion forum.
Thanks,
RK
Resolution History
22-MAY-02 19:25:05 GMT
Can you easily recover from, bypass or work around the problem? = NO
Does your system or application continue normally after the problem occurs? =
YES
Are the standard features of the system or application still available; is the
loss of service minor? = YES
### Problem Description: ###
I am using windows 2000. I found an article which said there is a new release
of ORARRP for windows 2000. Can I obtain the latest release of ORARRP.exe ?.
I am having trouble printing with ORARRP. I select the output file from the web
by clicking it. and it opens the printer dialog.. I hit O.K and nothing is sent
to the printer.
Need help.
### Upgrade or New Install?:###
Neither
### Error numbers/messages:###
no error messages.
###Log files faxed/emailed or uploaded ###
Uploaded
###Any workarounds ###
none
###Name & Version Details ###
none
### Were you able to complete this process previously? When? ###
no
### Can you duplicate the issue? What is the navigation path? ###
yes
###Is the problem in all environments? If not what's the difference?:###
Not Sure. Need to check with some one else who uses windows 2000.
###Any patches applied recently?:###
none
Contact me via : E-mail -> [email protected]
23-MAY-02 00:09:27 GMT
Issue needs to be addressed with Oracle Reports Developer. XFR->TOOLSREP
23-MAY-02 01:06:04 GMT
New info : Hi Oracle Support,
I found that the ORARRP works fine and submits report to the Printer if the
printer is defined through Novell Netware Network.
But if the same printer is defined through I.P address directly as a local
Printer it doesn't work. ( Add new port , Standard TCP/IP port method in
Windows 2000).
Does it give us any clue to solve this issue ?.
Pls. Help.
Thanks,
RK
23-MAY-02 13:19:58 GMT
Investigating this issue...
23-MAY-02 13:32:25 GMT
Hi,
My understanding is that you where trying to print using ORARRP utility on the web
Since you are trying on an muti-tiered server(that is web is 3-tier)
by default this report will be printed out to the default printer assigned to
the application server machine , NOT to the client machines default
printer.
For example,
Machine 1 - the application server machine
Machine 2 - the client machine
Machine 2 submits a request to run a report to the multi-tier server with
DESTYPE set to PRINTER; DESNAME is left blank.
Printing will be on the default printer of Machine 1(Application server)
and not on Machine 2(Client PC)
If I am wrong inmy understanding, please eloborate
Best rehards
Chandru
23-MAY-02 13:32:44 GMT
Email Update button has been pressed -- Sending email.
23-MAY-02 15:08:03 GMT
New info : A Big No. We are running the 10.7 version of Oracle applications and
there is no middle tier per se.
All we have done is to define a new printer called "LOCAL_PRINTER" and when
users select this printer the initiaization string which the Print command
sends to the printer before sending the file gets added to the output file and
the output file is stored in a directory which is accessible through a web
server.
Users invoke the browser and point to the website where the output files are
avaiable. and then click on their request ids. Since the extension of the file
is .rrpt the ORARRP utility brings the Printer dialog where we have select the
printer.
This setup was working sucessfully till so far. ( Past 1 year).
Now it suddenly didn't work for a user's printer which was connected to her PC.
Since I had windows 2000 on my laptop and I tried the same and found that the I
select a PC which is defined through I.P Address then it is not working. But
if I select the same printer defined through Novell Netware it is working.
Please let me know if you are getting the picture. if not may be we can do a
webex session or something like that.
Thanks,
RK
916-630-3508
23-MAY-02 15:51:40 GMT
Hi,
Sorry, I do not find any related notes on this issue
Possibly the PDF by name orarrp1.3.4.pdf in the ZIP file [downloadale at http://otn.oracle.com/sample_code/products/reports/files/Orarrp_1_3_4.zip] could show some pointers on this issue.
This PDF about this utility and is the only document I could find on this issue
ORARRP is a sample supllied "AS IS" to customers and is currently not supported by Oracle Support
Users facing any issues with this utility are encouraged to share their experiences in OTN forum at http://otn.oracle.com
This forum is being monitored by Product Management who can help customers as well as provide fixes for this utility
Please close the tar and post in OTN forum
Thanks
Chandru
23-MAY-02 15:51:51 GMT
Email Update button has been pressed -- Sending email.
23-MAY-02 10:24:13 : CHANGES MADE VIA MetaLink
NOT YET FORWARDED TO OUR INTERNAL SYSTEMS :
Closed by customer
Closing the TAR

Hi Radhakrishnan,
ORARRP doesn't actually do any printing itself. Via COM/Active-X, it calls the appropriate program that corresponds to the type of output, and then this program does the actual printing. For PDF, it calls Acrobat Reader to print the document. Acrobat Reader displays the printer dialog to let you choose which printer to use, and then when you click OK, Acrobat Reader prints the document and sends it to the printer.
I expect that you'll find that when you use Acrobat Reader yourself on this machine it has exactly the same problems with this particular printer configuration. If so, you'll need to contact Adobe for further assistance.
regards,
Stewart

MICR printing problem using the Crystal ReportDocument object in C# app

We developed a small C# windows program 6 months ago that reads a bank draft record and uses a Crystal Report form to print the draft (using ReportDocument() object and the PrintToPrinter() method). This has been working fine for 6 months. (using .Net 2.0 Framework and Crystal Reports .Net plugin included with VS 2005 on client machine - CRRedist2005_X64.msi)
Now the requirements have changed to put a MICR line at the bottom ot the draft check and print. We have updated a similar Crystal draft report form and printed from Crystal Viewer - this works fine. But when we update the Crystal report form used in the C# application, with the same MICR commands, using the same MICR printer, and the same user trying the print, it does not work. The MICR commands are printed on the draft just like regular text, instead of being interpreted by the printer as MICR commands. Must be something within the Crystal Reports .Net redistributable that is causing it to work incorrectly because it works correctly from the same users PC using Report Viewer.
Note: The MICR field on the Crystal Report contains the following chars:
&%STHPASSWORD$&%SMD' MICR '$&%STQ$
When we print, the above chars just print out like text
Can anybody help with any suggestions ?
Are they any hotfixes that address this issue of PCL commands not recognized on printer?

The app that is working is a C++ vendor app, however the Crystal piece is seperate piece that uses the Crystal Report Viewer to pull up the draft report. The print button is then hit within Crystal Report Viewer and the draft prints correctly.
- so the above app is using the Report Designer Component (craxdrt.dll) and as such it is not using the .NET assemblies...
For the app that is not working, we are not using Crystal Report Viewer, but are using the ReportDocument object, from the Crystal .Net Redistributable (referenced above), embeded into our C# app. The app executes a PrintToPrint command against the identical Crystal report, however, running it this way, the MICR command that is embeded into the report is not recognized by the MICR printer. The output seems to jumble the MICR command that I posted earlier in the thread and does not keep the command in a readable format for the MICR printer.
- the above is not using the Report Designer Component (craxdrt.dll). It is using the .NET assemblies and thus the .NET framework.
Have you been able to get .NET to recognize / see the fonts in that label I mentioned on 6/27/08?
Ludek

MICR Printing for Cheques

Hi all,
    IIam having Problem printing the MICR font on the Cheques . I searched many responses , but cudnt    get the solution yet.
We have installed   MICR font on the Cheque printer.
I have created character format MI which has family MICR_E and font 10.0 pt , coz only 10 or blank is available.
In the Script the code i have written is
      <MI>"C"&REGUD-CHECT&"C"</>   -----> For 1st one
     For the 2nd one
      <MI>"A"&REGUH-UBNKL&"A"</>
     For the 3 rd one
      <MI>&REGUH-UBKNT&"C"</>
The Output what iam getting in Normal printer is
"C"00069207    "A"000123456 0002220005678
Why is   "C"   and "A" getting printed , it must get converted to MICR font right?
             or
When i check it in MICR printer   does this come properly. The Problem is The MICR printer is at client place and i cant check it each and every time.
Please do let me know    the " " what iam using is right or wrong?
the MICR_E what i have taken is right ?
Please do let me know.
Regards,
Shuja

Dear Friend,
Please Try this...
For 1st one
<MI>&REGUD-CHECT&"C"</>
For the 2nd one
<MI>&REGUH-UBNKL&"A"</>
For the 3 rd one
<MI>&REGUH-UBKNT&"C"</>

Is there any best practice for printer configuration for test environment?

My Oracle ebs test environment has a scheduled refresh period where it will be refreshed with production test data and configuration time to time for BA, Dev to work on their enhancement.
However, all the printer configurations are still pointing to production ones after refreshed, which means whenever there is a testing on-going, the doc / label / invoices will be printed to production printer.
May I know if there is a way to globally change all the printer setup for the test environment, so that nothing will be directly to production?... Please assist.
(currently, the only way is to change one by one and only if you are aware of it...)
In case your organization has any other strategy on this matter, pls share also... Thanks a lot.

user6775047 wrote:
My Oracle ebs test environment has a scheduled refresh period where it will be refreshed with production test data and configuration time to time for BA, Dev to work on their enhancement.
However, all the printer configurations are still pointing to production ones after refreshed, which means whenever there is a testing on-going, the doc / label / invoices will be printed to production printer.
May I know if there is a way to globally change all the printer setup for the test environment, so that nothing will be directly to production?... Please assist.
(currently, the only way is to change one by one and only if you are aware of it...)
In case your organization has any other strategy on this matter, pls share also... Thanks a lot.If you do not want to use same printers then you have to it to point to the (TEST/BA Printers) after you are done with Rapid Clone. Any new printers need to be added manually (just the same way you defined you PROD printers) -- Rapid Clone Documentation Resources For Release 11i and 12 [ID 799735.1]
If you want to edit the configuration, you could use FNDLOAD to download printers definition from the source instance, update the ldt file and use FNDLOAD to upload printers definitions.
Is It Possible To Download/Upload Printer Definitions Using Fndload [ID 432616.1]
Tips About FNDLOAD [ID 735338.1]
Thanks,
Hussein

Printing character dash on MICR printer

Hi,
C&REGUD-CHECT&C A&REGUH-UBNKL&A &REGUH-UBKNT&C
I am Using the above code to print the check number and... On MICR printer.
Above the value of REGUH-UBNKL is 60020-002 on printer it is printing
60020 002 but I want to print this 60020002
I mean in between 60020 and 002 I want to print the character dash on printer.
For this what code changes I need to do in C&REGUD-CHECT&C A&REGUH-UBNKL&A &REGUH-UBKNT&C.
Thanks a lot.

Unfortunately, the zebra printer I have cannot print beyond 4 Inch width. I used to get this error initially but when I have created a custom device type which was copied from lb_zeb2 and included the page format ZBGLBL which is the page size of 2 1/2 X 4 1/2 I started getting this new error.
I am not sure, if this is the right way to handle this. Also do we need do some special coding using ZPL4 if yes where and what are those commands
Thanks
Venkat

How to save the print configuration

Hello, in my business, employees need to print multiple documents per day.
But for these specific documents, they need to print with a size of 105%.
My question is how to save the print configuration because they need to remplace the size by 105% every time ...
Please help me
(Sorry for my bad english, i'm french)

it was here : http://www.hostingpics.net/viewer.php?id=684187301.jpg
this screen appear after i press File -> print
and i need to put 105% every time i want to print document, how to save this ?
edit : this is not in the printer configuration

Error when I generate a PDF file - Can't parse printer configuration file:

I am receiving an error "Can't parse printer configuration file: uiprint.txt" when try generate to PDF file. The pdf file is generated but when I open the forms builder and show canvas the same error appears and canvas is shown in crazy way.
My uiprint.txt has the follows:
REPORTS_TMP=/tmp; export REPORTS_TMP
REPORTS_NO_DUMMY_PRINTER=TRUE; export REPORTS_NO_DUMMY_PRINTER
REPORTS_TAGLIB_URI=/WEB-INF/lib/reports_tld.jar; export REPORTS_TAGLIB_URI
REPORTS_CLASSPATH=$ORACLE_HOME/reports/jlib/rwbuilder.jar:$ORACLE_HOME/reports/jlib/rwrun.jar:$ORACLE_HOME/jlib/zrclient.jar:$ORACLE_HOME/j2ee/home/oc4j.jar:$ORACLE_HOME/j2ee/home/lib/ojsp.jar;export REPORTS_CLASSPATH
TK60_UNKNOWN=$ORACLE_HOME/guicommon6/tk60/admin; export TK60_UNKNOWN
TK60_PPD=$ORACLE_HOME/guicommon6/tk60/admin/PPD; export TK60_PPD
LE_HOME/guicommon9/tk90/admin/AFM; export TK90_AFM
TK60_FONTALIAS=$ORACLE_HOME/guicommon6/tk60/admin; export TK60_FONTALIAS
PRINTER=testprint;export PRINTER
TK2_PRINTER=echo;export TK2_PRINTER
testprint:PostScript:2:HP printer:hp4si3_1.ppd
Can someone help me?
Thanks

Hello,
The file uiprint.txt must not contain environment variables definitions.
Put the lines :
REPORTS_TMP=/tmp; export REPORTS_TMP
REPORTS_NO_DUMMY_PRINTER=TRUE; export REPORTS_NO_DUMMY_PRINTER
REPORTS_TAGLIB_URI=/WEB-INF/lib/reports_tld.jar; export REPORTS_TAGLIB_URI
REPORTS_CLASSPATH=$ORACLE_HOME/reports/jlib/rwbuilder.jar:$ORACLE_HOME/reports/jlib/rwrun.jar:$ORACLE_HOME/jlib/zrclient.jar:$ORACLE_HOME/j2ee/home/oc4j.jar:$ORACLE_HOME/j2ee/home/lib/ojsp.jar;export REPORTS_CLASSPATH
TK60_UNKNOWN=$ORACLE_HOME/guicommon6/tk60/admin; export TK60_UNKNOWN
TK60_PPD=$ORACLE_HOME/guicommon6/tk60/admin/PPD; export TK60_PPD
LE_HOME/guicommon9/tk90/admin/AFM; export TK90_AFM
TK60_FONTALIAS=$ORACLE_HOME/guicommon6/tk60/admin; export TK60_FONTALIAS
PRINTER=testprint;export PRINTER
TK2_PRINTER=echo;export TK2_PRINTER
in the file reports.sh
and keep only
testprint:PostScript:2:HP printer:hp4si3_1.ppd
in uiprint.txt
Regards

Print Configuration Dialog Box

Hello all,
I want to enable the print configuration dialog box pop up when a button is clicked in vi.
This is standard windows printer configuration dialog box which pops up when any file (xls,txt etc.)
is tried printing.Any suggestions please ?
Also i have attached the standard windows print dialog box, just incase.
Thanks in advance,
Nalin
Attachments:
print.JPG ‏33 KB

In general use a property node with nothing attached to it in LabVIEW with the property Printing >> Default Printer or Printing >> Avalaible Printers to return the printers configured with Windows. One of these string items can be wired into the printer input of the report generation Print Report VI to select a printer.
In regards to the Microsoft Common Dialog 6.0 ActiveX controls, the printer selection from the dialog seems to be determined by the hDC output, which stands for hardware device context. If you modify the demo posted above to send in the appropriate flag value, either an informational or a direct hardware device context handle is returned in the ICommon property hDC. Input the flag value 512 to the ICommonDialog property Flags to return an hardware device context handle from the hDC property, or 1024 to return an informational device context.
More information about how to extract any meaningful information from this I32 number can doubtlessly be found at msdn.com, but I'm not sure personally how to do it. Specifically, here are a few posts to start your search at:
Using the Print Dialog Box
http://msdn.microsoft.com/library/default.asp?url=/library/en-us/vbcon98/html/vbconusingprintdialogb...
Common DialogControl Constants
http://msdn.microsoft.com/library/default.asp?url=/library/en-us/cmdlg98/html/vbidxCommonDialogContr...
Alternatively, consider avoiding the Common Dialog Control calling a dll that will directly return the selected printer name from a dialog:
http://support.microsoft.com/default.aspx?scid=kb;en-us;322710
Hope this helps!
Jarrod S.
National Instruments

Printer Configuration for PDF Display in New NWBC Window

please am implementing SAP Note 1069540 -Printer Configuration for PDF Display in New NWBC Window
and when i finished the configuration i the pdf tab was still not created..
i decided to trace the error and i noticed that in service /sap/bc/webdynpro/sap/WDK_SPOOL_TO_PDF
when i right click and test service i get an error
Client error
Host name lookup for 'dv1sap.mis.com' failed
guess thats why my pdf tab was not created in my NWBC..
can any one help..please...ASAP

do you have maintained the host and ip adress in the hosts file of your system
It seems it is not able to recognize the host
just define an entry and then try
Rohit

Transfer Printer configuration between Macs

Hi all,
I had to configure a computer with 32 printers.
Now I have to the same with another 200 computers running 10.3 and 10.4.
I was wondering if anyone knows if is there any other way rather than going computer by computer configuring all the 32 printers. That would take ages and it is not an option.
Print server option would not work for me either.
Basically I was thinking on taking the relevant printer configuration files from the computer that has already been configured and transfer them to each of the other new computers. By doing that I hope to get the new computers configured upon restart. Now I just need to find out which ones are the right files. Does anyone know?
Thanks in advance
John

Never mind.(and I was wrong. Since Tiger came out and Apple changed the structure of the forums it has moved.)
It appears that Greg has answered your question on the Tiger forum in the printing and faxing section.
I still think that there may be an issue with the addressing of the printers but try it on a few computers to find out.
The folder that you need to access is invisible and will not show up in the finder. If you use the search function (not the little window in a finder window) and add "search visibility both visible and invisible" and enter the folder name "/cups/printers.config" it will show you the folder that you need to get to.
Good luck. I wouldn't want to map out 32 printers for 200 macs either.

[Solution][KDE] KCmodule problem in Printer Configuration

In file "/usr/lib/python2.7/posixpath.py" I removed "or path.endswith('/')" from line 67
and the Printer Configuration works for me again, but i have concern that it might cause for issues in another places on KDE, can someone help me to find an any issues that caused by this solution?
Tnx,
soomsoom
PS: Sorry for my bad English.
https://bugs.archlinux.org/task/21341?p … rinter-kde
Last edited by soomsoom (2010-10-22 10:41:03)

Hi!
We are facing the same problem.
http://xxxxxxxxxxxxx::8000/webdynpro/dispatcher/sap.com/tcsmdnavigation/StandaloneApp?APP_ID=ADMIN_INTROSCOPE_AGENT
500 Internal Server Error
SAP NetWeaver Application Server 7.00/Java AS 7.00
Failed to process request. Please contact your system administrator.
Did you find any solution to the issue? The note 1276263 is not availible.
/Anton Renberg

Zebra printer configuration in SAP 4.6C

Hi,
I am trying to print in Zebra printer (Model Zebra 200Dpi), but output is not coming in printer. However the spool/output requests are having status as 'completed'. Still the output is not coming in the printer.
Printer Configuration Details:
1. Device type 'LB_ZEB -Zebra Label Printer IBM850
2. Host spool access method - F
Any advice on this is highly appreciated.
Regards,

Check this, might be helpful
[Any Idea on ZEBRA Printer Configuration in SAP]

Printer configuration for enterprise release 5.6.2 on windows platform.

Hi All,
Database configuration
=======================
XML publisher 5.6.2 installed on host "aranagir-pc1"
Then i configured scheduler and the database as:-
<url>jdbc:oracle:thin:@127.0.0.1:1521:XE</url>
I could run view the outut for the report Employee Salary Report but while
printing it gives me error.
PRINTER CONFIGURATION
=====================
Printer to be configured is "HydCampus-P1-2FL-1" which has the IP address as 10.176.112.99
and port as 515.
I wwas able to browser using url
http://10.176.112.99, so its a ipp enabled printer.
My server name :- HydCampus-P1-2FL-1
Host :- 10.176.112.99
port:- 515
uri:- ipp://10.176.112.99:515/
Help me to configure printer(ipp) on the windows platform and guide me how to define
printer configuration parameter.
But it is failling with the error as
[101906_091928332][][EXCEPTION] oracle.apps.xdo.servlet.scheduler.ProcessingExce
ption: oracle.xdo.server.delivery.DeliveryException: oracle.apps.xdo.delivery.De
liveryException: Software caused connection abort: socket write error
at oracle.apps.xdo.servlet.scheduler.XDOJob.deliver(XDOJob.java:1034)
at oracle.apps.xdo.servlet.scheduler.XDOJob.execute(XDOJob.java:317)
at org.quartz.core.JobRunShell.run(JobRunShell.java:195)
at org.quartz.simpl.SimpleThreadPool$WorkerThread.run(SimpleThreadPool.j
ava:520)
Caused by: oracle.xdo.server.delivery.DeliveryException: oracle.apps.xdo.deliver
y.DeliveryException: Software caused connection abort: socket write error
at oracle.xdo.server.delivery.impl.DeliveryServiceImpl.deliverToPrinter(
DeliveryServiceImpl.java:349)
at oracle.apps.xdo.servlet.scheduler.XDOJob.deliver(XDOJob.java:910)
... 3 more
Caused by: oracle.apps.xdo.delivery.DeliveryException: Software caused connectio
n abort: socket write error
at oracle.apps.xdo.delivery.ipp.IPPDeliveryRequestHandler.submitRequest(
IPPDeliveryRequestHandler.java:476)
at oracle.apps.xdo.delivery.AbstractDeliveryRequest.submit(AbstractDeliv
eryRequest.java:1267)
at oracle.xdo.server.delivery.impl.DeliveryServiceImpl.deliverToPrinter(
DeliveryServiceImpl.java:343)
... 4 more
Caused by: java.net.SocketException: Software caused connection abort: socket wr
ite error
at java.net.SocketOutputStream.socketWrite0(Native Method)
at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92)
at java.net.SocketOutputStream.write(SocketOutputStream.java:136)
at oracle.apps.xdo.delivery.ipp.IPPMessageHandler.writeAsciiValue(IPPMes
sageHandler.java:721)
at oracle.apps.xdo.delivery.ipp.IPPMessageHandler.writeAttribute(IPPMess
ageHandler.java:657)
at oracle.apps.xdo.delivery.ipp.IPPMessageHandler.writeMessage(IPPMessag
eHandler.java:821)
at oracle.apps.xdo.delivery.ipp.IPPDeliveryRequestHandler.submitRequest(
IPPDeliveryRequestHandler.java:342)
... 6 more
Regards,
Ajay
Message was edited by:
user501772

Hi All,
Database configuration
=======================
XML publisher 5.6.2 installed on host "aranagir-pc1"
Then i configured scheduler and the database as:-
<url>jdbc:oracle:thin:@127.0.0.1:1521:XE</url>
I could run view the outut for the report Employee Salary Report but while
printing it gives me error.
PRINTER CONFIGURATION
=====================
Printer to be configured is "HydCampus-P1-2FL-1" which has the IP address as 10.176.112.99
and port as 515.
I wwas able to browser using url
http://10.176.112.99, so its a ipp enabled printer.
My server name :- HydCampus-P1-2FL-1
Host :- 10.176.112.99
port:- 515
uri:- ipp://10.176.112.99:515/
Help me to configure printer(ipp) on the windows platform and guide me how to define
printer configuration parameter.
But it is failling with the error as
[101906_091928332][][EXCEPTION] oracle.apps.xdo.servlet.scheduler.ProcessingExce
ption: oracle.xdo.server.delivery.DeliveryException: oracle.apps.xdo.delivery.De
liveryException: Software caused connection abort: socket write error
at oracle.apps.xdo.servlet.scheduler.XDOJob.deliver(XDOJob.java:1034)
at oracle.apps.xdo.servlet.scheduler.XDOJob.execute(XDOJob.java:317)
at org.quartz.core.JobRunShell.run(JobRunShell.java:195)
at org.quartz.simpl.SimpleThreadPool$WorkerThread.run(SimpleThreadPool.j
ava:520)
Caused by: oracle.xdo.server.delivery.DeliveryException: oracle.apps.xdo.deliver
y.DeliveryException: Software caused connection abort: socket write error
at oracle.xdo.server.delivery.impl.DeliveryServiceImpl.deliverToPrinter(
DeliveryServiceImpl.java:349)
at oracle.apps.xdo.servlet.scheduler.XDOJob.deliver(XDOJob.java:910)
... 3 more
Caused by: oracle.apps.xdo.delivery.DeliveryException: Software caused connectio
n abort: socket write error
at oracle.apps.xdo.delivery.ipp.IPPDeliveryRequestHandler.submitRequest(
IPPDeliveryRequestHandler.java:476)
at oracle.apps.xdo.delivery.AbstractDeliveryRequest.submit(AbstractDeliv
eryRequest.java:1267)
at oracle.xdo.server.delivery.impl.DeliveryServiceImpl.deliverToPrinter(
DeliveryServiceImpl.java:343)
... 4 more
Caused by: java.net.SocketException: Software caused connection abort: socket wr
ite error
at java.net.SocketOutputStream.socketWrite0(Native Method)
at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92)
at java.net.SocketOutputStream.write(SocketOutputStream.java:136)
at oracle.apps.xdo.delivery.ipp.IPPMessageHandler.writeAsciiValue(IPPMes
sageHandler.java:721)
at oracle.apps.xdo.delivery.ipp.IPPMessageHandler.writeAttribute(IPPMess
ageHandler.java:657)
at oracle.apps.xdo.delivery.ipp.IPPMessageHandler.writeMessage(IPPMessag
eHandler.java:821)
at oracle.apps.xdo.delivery.ipp.IPPDeliveryRequestHandler.submitRequest(
IPPDeliveryRequestHandler.java:342)
... 6 more
Regards,
Ajay
Message was edited by:
user501772

MICR printer configuration

Similar Messages

Maybe you are looking for