Micro sd recognition problem

I have nokia 2700 classic and after firmware update the phone can't recognize the sd nokia card.
I tried with a diferrent card too and ocurres the same.
If someone knows about this issue , i will appreciate it.
thanks

try blowing into the slot where the card goes there maybe some dust or dirt trapped in there
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Similar Messages

MTP and recognition problems with Zen Mi

Ok here I go, I have a 5 gig Zen micro.and here are my issues. I updated my players firmware a few months ago because it was running oddly. This worked beautifully and fixed the running oddly part. This was great until I got a new computer. I went to plug my player in and realized I did not have the proper software/drivers so i go to creative's site and download the ones I need. I finish all instillation stuff. I have media player . And when i plug the player in suddenly i get infinite recognition messages for an MTP device from windows. It keeps popping up until i disconnect the player at which time it says device installed but may not perform correctly. Ok so I realize something is wrong and I go forum trolling. I find people that say you need to downgrade media player from try that is still no go. I try to install different drivers. I try to install different software none of these fix the issue. On other computers i can get it to recongnize the player as a MTP device and load up. But as one of the fixes I went to the recovery mode and did a firmware reload. This went fine and the player still comes up and I can get it recognized but when I try to use the firmware installer (this is on other computers mine still does not fully recognize my Zen Mirco) It says device not found yet i can see it in my computer and it shows up as connected media device. I would first like to get the firmware reinstalled on my player. I can still goto the recovery mode screen. Then I would like help trouble shooting my MTP recognition problem.

Ok well my I can load my player up with music with the old firmware. But for some reason I cannot use WMP because as soon as I update my current one I get the same error as before. So this is still an issue as I would like to be able to use WMP and I would also like to be able to use the new firmware but I think that will mess things up again also.

Zen Vision:M 30GB recognition problems...Big t

Hi, 2 days ago i ran into a problem with my Zen. I had to charge it, as the battery was low and had to put some new music on it.. I plugged it into the USB port on my Laptop, where all of it's software is installed. The Zen wasn't recognized. Instead of the charging screen it normally started up with, it started up with the play screen(the screen it shows when a song is playing). I looked at the battery icon in the top right corner, and it wasn't doing anything. I turned the Zen off and started it up again. Nothing changed. I restarted my computer. Nothing changed. I shut down my computer and started it back up again. Nothing changed.
I took it to my desktop computer, a Compaq, and tried it there. It worked, but not how i was expecting it to work. The battery icon started flashing with the little lightning bolt, acknowledging that it was charging. But the play screen was still there. The odd thing with this is, i left the player to charge for several hours. When i came back, the Zen was in some form of idle shut-down. The screen was black, except for the battery icon with the lightning bolt. Oddly enough, he battery bar hadn't filled up anymore than when i left it. Upon unplugging the player though, the Zen turned off. When i turned it back on, the bar had filled up more. It wasn't fully charged though.
I plugged the cable back into it, and this time, the battery icon WASN'T charging. It just had the play screen on. It wasn't doing ANYTHING this time. Frustrated, i went out and bought the wall charger, and now i have a full battery. But it doesn't solve why my computer won't recognize my player.
Today, i un-installed the software that came with the player and re-installed it. It didn't do anything. I installed the software on my desktop computer, and THAT didn't work either. So i came to the website here and used the trouble-shoot guide. That didn't help, and this is where my problem differs from the other posters here who have recognition problems:
Back to my laptop: I have Windows Service Pack 2. I installed Windows Media Player . I went to the Device Manger, like the trouble-shoot guide said to. The kicker: Windows Portable Devices is NOT, i repeat NOT in my Device Manager. Neither does the Creative player either. I clicked on "The player does not appear in Device manager". That link showed me a diagram of a desktop computer, so went back to my desktop computer. I did everything above mentioned, and Windows Portable Devices is not in the device manager of my desktop computer either. Further reading the trouble-shoot guide, i could NOT locate "Other Devices" or "Unknown Devices" in my Device Manger on either desktop or laptop. There's nothing "Creative" related or "Zen" related at all in any of the Device programs.
I don't know what to do. All of the trouble-shoot guides don't discuss my issue at all. Everything is "If an MP3 player is reported working properly in Device Manager, but it is not detected or listed in Windows Media Player or Creative Media Explorer..."
Mine isn't even detected in Device Manager. My Device Manager has nothing regarding my Zen or Windows Portable Devices.
I'm thinking about messing with it in Recovery mode, but i don't want to erase everything i have on here, just to have my player still not work. I'm going to try messing with this at my friend's house to check the cable and the player there too.
But any help regarding my situation would be greatly appreciated. This is driving me crazy.

I tried my uncle's Zen Vision: M 30GB on my laptop and strange things happened. My laptop recognized the player as an unknown device and said i needed to install the MTP driver. I did that, and upon doing so, my laptop recognized my Uncle's player as a Portable device, allowing me to transfer songs to his player. But it STILL doesn't recognize MY player. Email support says i have to send it in for repairs, but i don't know...
Any luck with you?

Debian Linux character recognition problem

Maybe this shouldn't be on this forum, but perhaps someone can help me...
I have Jrun 3.1, java 2 1.4 and Debian Linux.
On our test server everything was hunky dory, running perfectly.
But once everything was on the real server, we've had a character recognition problem. All of the higher characters are just replaced by a y or a ?.
I'm pretty sure that we can exclude java from the problem, the i18n.jar, which I believe holds all the international stuff is there and in the classpath (exactly as on the test server) and jrun is exactly as on the test server because we copied every folder as it was.
Therefore I think we can bring it down to Linux (Debian).
I cannot find where to look in Debian for any kind of keyboard or locale problem. Anyone know what to do?
kbdconfig command doesn't exist on our system.
Any help greatly appreciated.
We are in Italy, by the way.
Thanks.

If you check out the default file encoding you'll find that it's 7-bit ASCII; no characters > '\u007F' come out as they should. This applies as well to compiling as to running.
You can compile with another character encoding using the command line options, like: "javac -encoding ISO-8859-1 package/YourClass.java" (available at least in 1.4) and "java -Dfile.encoding=iso-8859-1 package.YourClass".

Touch ID recognition problems

I've been using Touch ID for over a week. I'm trying to figure out why it isn't working.
The problem is that after I "enroll" my fingers (thumbs and index fingers), it works for maybe 5 or 10 minutes. After that, the sensor becomes extremely flaky and starts to fail to recognize any of the enrolled fingers.
According to my best estimates, the phone only unlocks about 5% of the time. The rest of the time, it just says "try again" and forces me to eventually enter a passcode. I wipe off the sensor, dry my fingers, wash my hands to remove oils, etc. to no avail. A few times, it worked consistently (1 or 2 touches to unlock) for about an hour at a time before it became inaccurate again.
I've tried removing and re-enrolling my fingers, but the same thing happens. I've heard a lot of stories about people using it and finding that it works relatively well, so I'm stumped on why it isn't working for my fingers. I called Apple and they didn't know enough to figure out why the sensor isn't working properly. My best guess had to do with temperature variations, but recent testing has ruled that out (I enrolled after washing and drying my hands, waited a half an hour, washed and dried my hands again, and it failed to unlock, all while being in a temperature-controlled room).
If anyone else has had this poor performance and been able to determine the cause, I'd like to know. Please don't just post that "it works for you" unless you have some useful information.
Thanks.

I also had the touch ID recognition problem come up after the last update. I did find that scrubbing the screen with the same finger used to access your phone may help motivate the sensor and actually works more often for me then not. Try scrubbing the screen before placing the recognized finger on the sensor. See if that works for you...

5th Gen Recognition Problems

I'm one in a list of many on these pages who appear to be having the same problem. I have tried all the fixes suggested vy Apple without success and I'm about to return the useless piece of crap to Apple in the hope that a new one will be more useful than the £300 doorstop I have at present.
For anyone that has sent their iPod back to Apple and had a replacement sent, has this solved the problem? If not, has anyone been successful in having their money refunded?
I'm concerned that returning the iPod will serve only to replace one with 8000 songs on it which is no longer recognised by my PC, with one with no songs on it which is not recognised by my PC. I've already spent 30 hours or so trying every conceivable fix with the gadget, and I'm concerned that there appears to be a very real - but unidentifiable - flaw with the product which seems to sporadically appear and make it impossible to update.
Anyone had any good news when dealing with Apple on this front?

Well, I now am back to 9000 songs and a couple of movies! How did I manage this given the recognition problems I've been having with iPod and Windows?
Easy. Explained the problems to those nice people at PC World in Edinburgh and they gave me a Creative Zen Vision M as a replacement plus the £60 so of difference in price.
So, back up to speed with my portable music and movies, and an FM Radio on it too. I seriously thought I had thrown my money down the toilet with the iPod and I'm delighted that PC World showed the sort of customer service they are not generally renowned for.
Interestingly, they were saying that they have had a lot of problems with the iPod - particularly in recent weeks. I hope Creative don't go the same way!

Western Digitial external USB drive recognition problem

Hi
I recently bought a Western Digital USB 250gb external drive. I connected it to my G4 Powerbook running OSX10.2.8 and it had no problem recognising it. I then dumped across a load of data successfully.
A few days later I upgraded to Tiger and now the G4 won't recognise the external drive at all. I have scoured the forums for an answer but have found nothing to fix a drive problem where the drive just doesn't appear at all in disk utility (or on the desktop)!
I didn't partition the drive when it was first recognised in 10.2.8 (which i now realise was a mistake). The data on the external drive is unimportant to me - I just want to be able to use the drive - maybe there's a way or reformatting and starting again? (The Western Digital site doesn't provide any drivers for Tiger - cos it's just meant to recognise it automatically..)
Any information appreciated.
Many thanks,
Mark

Welcome to Apple Discussions!
Do you have any other USB devices connected to your Powerbook?
Is this a recognition problem right after the computer boots up? Or had the computer fallen to sleep prior to your connecting it? Sometimes I've seen USB ports fall into a low power mode causing problems recognizing USB devices until the machine is next rebooted.
If you have critical data on that drive, you may want to try Prosoft Data Rescue to see if it can see what is on that drive. You can also buy an external Firewire enclosure and try to move the drive to that, or find someone with a PowerMac G4 or G3 tower to see if it can be taken out of the case and put in the tower for recognition. If you do the latter, be sure that the jumper is set for the master/slave setting that matches the cable you are connecting in the drive.

ZEN MICRO detection problems / recognition problems 9

For the life of me I can't figure this out. My brother bought a Zen micro a few days ago and we tried to install it but the comp WILL detect the ZM but will not/can not find a driver. Thus "?!Creative Zen Micro" appears in the Device manager under "? Other Devices" but will not work. Have read and tried alot, but nothing. Using an old Celeron 900MHz with Windows 98SE. Did many fresh installs from install disk....but nothing. Even tried a diff USB cable (though longer) and diff USB port....but nothing. The comp detects the Zen Micro (as named above) but is unable to find the drivers eventhough when requested I direct the detection to the Install disk for any drivers it may contain. Any knowledge shared would be appreciated.Message Edited by microscan on 02-06-2006 06:40 AM

I tried those before but just for good measure I just now again tried them. Nothing has changed. Still detecting but not recognizing/no driver. I forgot to mention last time that even when I try to open the program "Creative System Information" (by clicking on "Start", "Programs", "Creative") I get "This program has performed an illegal operation and will be shut down." When I click on details of this Ctsi problem window I get this:
CTSI caused an invalid page fault inmodule CTSI.EXE at 067:0042d273.Registers:EAX=0c6804 CS=067 EIP=0042d273 EFLGS=000026EBX=7f832e2 SS=06f ESP=0e6fdd0 EBP=0e6fdd8ECX=00000005 DS=06f ESI=0c68000 FS=d7EDX=00000000 ES=06f EDI=0c67fa0 GS=0000Bytes at CS:EIP:f3 a5 ff 24 95 88 d3 42 00 8b c7 ba 03 00 00 00 Stack dump:0c67fd0 00000000 0e6fe4 0040fac5 0c67f70 0c67fd0 00000044 0040fa3a 0c67fd0 000000c 0c66d0 0e6fe40 0e6fe0 00000002 000000c 0c66d0
anyone have a clue?

Speech recognition problem with null pointer exception

im trying to run the simple hello program that came with IBM speech for java
i've put the speech.jar file in the right folder and it compiles all fine but when i run it i get this error:
locale is en_US
java.lang.NullPointerException
at Hello.main(Hello.java:171)
but i dont know enough about java speech to figure out what is null and what shouldn't be null...
thx
nate
P.S.
here is the program code
import java.io.*;
import java.util.Locale;
import java.util.ResourceBundle;
import java.util.StringTokenizer;
import javax.speech.*;
import javax.speech.recognition.*;
import javax.speech.synthesis.*;
public class Hello {
static RuleGrammar ruleGrammar;
static DictationGrammar dictationGrammar;
static Recognizer recognizer;
static Synthesizer synthesizer;
static ResourceBundle resources;
static ResultListener ruleListener = new ResultAdapter() {
public void resultAccepted(ResultEvent e) {
try {
FinalRuleResult result = (FinalRuleResult) e.getSource();
String tags[] = result.getTags();
if (tags[0].equals("name")) {
String s = resources.getString("hello");
for (int i=1; i<tags.length; i++)
s += " " + tags;
speak(s);
} else if (tags[0].equals("begin")) {
speak(resources.getString("listening"));
ruleGrammar.setEnabled(false);
ruleGrammar.setEnabled("<stop>", true);
dictationGrammar.setEnabled(true);
recognizer.commitChanges();
} else if (tags[0].equals("stop")) {
dictationGrammar.setEnabled(false);
ruleGrammar.setEnabled(true);
recognizer.commitChanges();
} else if (tags[0].equals("bye")) {
speak(resources.getString("bye"));
if (synthesizer!=null)
synthesizer.waitEngineState(Synthesizer.QUEUE_EMPTY);
Thread.sleep(1000);
System.exit(0);
} catch (Exception ex) {
ex.printStackTrace();
int i = 0;
String eh[] = null;
public void resultRejected(ResultEvent e) {
if (eh==null) {
String s = resources.getString("eh");
StringTokenizer t = new StringTokenizer(s);
int n = t.countTokens();
eh = new String[n];
for (int i=0; i<n; i++)
eh = t.nextToken();
if (((Result)(e.getSource())).numTokens() > 2)
speak(eh[(i++)%eh.length]);
static ResultListener dictationListener = new ResultAdapter() {
int n = 0; // number of tokens seen so far
public void resultUpdated(ResultEvent e) {
Result result = (Result) e.getSource();
for (int i=n; i<result.numTokens(); i++)
System.out.println(result.getBestToken(i).getSpokenText());
n = result.numTokens();
public void resultAccepted(ResultEvent e) {
Result result = (Result) e.getSource();
String s = "";
for (int i=0; i<n; i++)
s += result.getBestToken(i).getSpokenText() + " ";
speak(s);
n = 0;
static RecognizerAudioListener audioListener =new RecognizerAudioAdapter(){
public void audioLevel(RecognizerAudioEvent e) {
System.out.println("volume " + e.getAudioLevel());
static EngineListener engineListener = new EngineAdapter() {
public void engineError(EngineErrorEvent e) {
System.out.println
("Engine error: " + e.getEngineError().getMessage());
static void speak(String s) {
if (synthesizer!=null) {
try {
synthesizer.speak(s, null);
} catch (Exception e) {
e.printStackTrace();
} else
System.out.println(s);
public static void main(String args[]) {
try {
if (args.length>0) Locale.setDefault(new Locale(args[0], ""));
if (args.length>1) Locale.setDefault(new Locale(args[0], args[1]));
System.out.println("locale is " + Locale.getDefault());
resources = ResourceBundle.getBundle("res");
recognizer = Central.createRecognizer(null);
recognizer.allocate();
recognizer.getAudioManager().addAudioListener(audioListener);
recognizer.addEngineListener(engineListener);
dictationGrammar = recognizer.getDictationGrammar(null);
dictationGrammar.addResultListener(dictationListener);
String grammarName = resources.getString("grammar");
Reader reader = new FileReader(grammarName);
ruleGrammar = recognizer.loadJSGF(reader);
ruleGrammar.addResultListener(ruleListener);
ruleGrammar.setEnabled(true);
recognizer.commitChanges();
recognizer.requestFocus();
recognizer.resume();
synthesizer = Central.createSynthesizer(null);
if (synthesizer!=null) {
synthesizer.allocate();
synthesizer.addEngineListener(engineListener);
speak(resources.getString("greeting"));
} catch (Exception e) {
e.printStackTrace();
System.exit(-1);

yes, the problem seems to be with allocating the engine, but I don't know exactly why recognizer.allocate() returns null...I have already installed IBM ViaVoice and Speech for Java, and have set the supposedly correct paths...

Nokia 5700 512 mb bundled micro sd card problem.

hi,
i am getting "certifictae error.Contact application supplier" error after about 80% installation is complete on most of my .jar files on this nokia supplied micro sd card.i cud install some of these apps. earlier.( the phone is only 7 days old). the same apps. insatll without a hitch on the phone memory or on another Transcend sd card which i hv.i cannot format the card also as it has bundled songs on it.is there any particular file on it which can be deleted to remove the problem.
please help.

is there any other forum where i can get help for this?

Nokia c1-02 micro sd card problem

I have a 4GB kingston class-4 micro SD card
In my old samsung corbypro in mass storage(connected via cable) mode the transfer speed is 3.8MB/s
In my new nokia c1-02 in mass storage(connected via cable) mode the transfer speed is just 0.8 MB/s and windows says "this device can perform faster" and suggests me to connect it to Hi-speed usb 2.0 port(all ports in my biostar ta790gxb motherboard are usb 2.0).
Its the same cable, same usb port and same memory card. Only the phone is different. I didn't get the windows suggestion in samsung corbypro.
I think the problem is with the phone. Maybe some firmware update in future will fix it. Or do I have to do something else?

It's nice if you have successed to update software. I have same problem as you but I can't even update firmware. You are lucky man even
I've tried to upgrade firmqare via Nokia Ovi Suite and Nokia Software Updater but same problem, always show after ~2 minutes that PC lost connection with device. I've tried it in several computers and different Windows but same problem.
I would add one more interesting thing, at official site there's written that firmware update is possible also directly via phone by using "Select Menu > Settings > Phone > Phone Updates." but my phone doesn't have that option. Also doesn't have :
"Set auto-check on in 30 seconds
1. Select Menu > Applications > SW Update
2. Select Options > Settings > Auto-check for updates
3. Select On and OK."
By the way, I wanted to update firmware because I loose all sms messages from every folder when I restart device and restoring to factory default doesn't help. Also USB works slow "Device can perform faster" but I thought it's normal.
Be happy that you, at least, successed to upgrade firmware

E90 micro SD card problem

Hi.
I've got Apacer 1 Gb micro SD card. Everything was working fine. But after I renewed the software of my Nokia E90, the micro SD cannot be found by PC with USB adapter. I thought the card crashed or smthng. So I bought a SanDisk 4Gb card. Firstly everything OK. After that I put this card to E90 card slot. Made some copyings. Back to USB adapter and again not working. My PC shows no card present in the adaptor.
Does anybody face the same problem?
Any solution for that?
Thanks.
Elyga

Hi all;
I was facing the same issue
Got my card replaced several times and tried several times to hard-reset also but could not have this fixed until ... few hours ago
When I hardReset my phone, I setup the "remote lock by SMS feature" on the phone - which allows me to lock rapidly the phone if lost or whatever
Once done I test the feature (send myself an SMS and make sure it's properly setup)
Once locked, I just push the "unlock" button, enter my code and that's it
But did not pay attention to the message "Phone and Card locked"
So I went to "Memory" app on the phone and choosed "Option/remove password"
then entered the lockCode sent over SMS
And ... wouaaaahhhh I got my 8Gb back available via my standard diskReader
issue solved now
I hope this could be helpfull to some of you
-- DaWaBZ --

Zen Micro - two more problems...... oye

So last week I received my replacement Zen Micro (the headphone jack was faulty in the old one..... etc etc).
Since the new one arri'ved, I've had two problems:
)There is a constant ringing coming out of the player when it is switched on, like a buzzing noise.....
2)Today while flicking to a track, it crashed like a computer. The screen froze and I couldn't do anything with it, had to remove the battery.
Anyone have any clues wat I should do? Besides going back 4 months and buying an iRi'ver instead.....

I have had it alright with my player after I used clean up and reloaded the firmware, But last night, just got in, Took my player out of my pocket to turn it off. Switched the power button from hold to turn it off. But when I moved the button the player still said it was locked. I moved the button back to locked, and then back again, but still nothing. Once again I had to remove the battery.
Creative make the removable battery a selling point, but in fact its the only way to turn the bloody thing off sometimes. And the only reason I don't send it back is because I will never get a replacement by the time I go on holiday. But once again it seems fine, but I'm just waiting for the next crappy thing to happen.
oh, and I left it on pause today in my pocket, (only for a minute) then when I pressed play on my remote nothing happened. So I checked the player to find that top half of the screen was black and the bottom was white. And guess how you fix it's ....... that's right you have to take the battery out. Its random stuff like this I put I with day to day which I don't think I shouldn't be doing. I know everything has a bug or to in it, but this just getting out of hand. I don't like to go on, and At the start when I go my player I was fine, and I was happy with it. But now only after a week or two, its turned in to a player from hell. Once I'm back in the UK I might have to send it back. The thing is driving me mad.
I don't know, I just feel let down

Zen Micro Headphone Jack problems-are the new ones

Gonna buy a Zen Micro Photo 8GB player-had one of the 5gb ones a year and a half ago and the headphone jack went on that-have the problems with the headphone jack been sorted out in the new ones?

I have not seen any reports of problems with the Zen MicroPhoto's headphone jack.
Cat

Face Recognition Problem in PSE 12

I am having a problem with face recognition with PSE 12/Windows 8.1. It is a new install, at first all went well. I could enter names and they were immediately accepted. As faces repeated recognition was working and I could click the green arrow and it would accept or even click the red x and make another selection as it should be. Then I started having problems when it would come up with the correct face I would click the green arrow and instead of accepting the box would go to "Who is This" and it would take numerous attempts to get the program to accept the name. Next I started having problems just entering names, again instead of accepting it would loop me through the "Who is This" numerous times. Any suggestions?
Thanks in advance

Hi,
We sincerely apologize for the problem that you have been facing while using a trackpad with Photoshop Elements 11 & 12 on Mac OSX 10.10 (Yosemite).
We have been actively working with Apple to resolve this problem as quickly as possible. We're hopeful this will get completely resolved in an upcoming update of Yosemite(MAC 10.10).
In the meanwhile, you have two options to work around this problem:
1. Option1: Use a mouse instead of the trackpad
2. Option2: Install a plug-in which should workaround the problem
Plug-in installation instructions:
1. Close Photoshop Elements
2. Download this zip file to a location you can easily find (e.g. your desktop)
3. Unzip the file, WhiteWindowWorkaround.plugin, and move it to the Plug-In folder:
• For Elements 12 – //Applications/Adobe Photoshop Elements 12/Support Files/Plug-Ins/
• For Elements 11 - //Applications/Adobe Photoshop Elements 11/Support Files/Plug-Ins/
You can verify the plug-in is installed by launching the Photoshop Elements Editor and choosing Help > System Info... Scroll to the bottom of the text in the dialog and look for the plug-in name "WhiteWindowWorkaround.plugin".
Note: This plugin is a temporary workaround and should be used until this issue is addressed in Mac OSX 10.10 (Yosemite). Please remove this plugin once the issue is officially resolved by Apple.
If you are using a stylus in conjunction with a trackpad, you might see issues with your trackpad. Workaround in this particular case is to use mouse instead of the trackpad.
Hope this helps!
Regards,
vaishali

Micro sd recognition problem

Similar Messages

Maybe you are looking for