Microphone does not work after restarting computer
I just received the Creative Xmod soundcard yesterday after using an Icemat siberia usb headset sound card for a couple months. The sound is a lot better with the creative soundcard however, if I restart my computer and go back into ventrilo, my microphone does not work. It doesnt make any sound when I talk into it (almost as if it muted itself) but it hasnt. I check my sound settings and everything is the way it should be.....but the mic isnt producing any sound. It is not my headphones that is causing the problem because I have never had this problem with my old icemat soundcard. I am currently using :
Sennheiser PC350 headset
Windows XP Home Edition
The newest version of Ventrilo
http://picsend.net/images/240403ventsetup.JPG
That is how I have ventrilo setup. A friend of mine said I should Mux set to Record Control, but it only gives me the option for Wave In =/
Similar Messages
-
PCI wireless card does not work after restart - FM2-A55M-E33
Installed TP-LINK WN751ND wireless PCI card onto FM2-A55M-E33 motherboard. The card works fine after cold start, but does not work after restart. Windows recognises the card, but it gets code 10, cannot start.
BIOS is updated (v.11.1), as well as drivers and Windows 7 64.
I suspect that this might be the issue: Incorrect ASPM Transitions on the GPP Interface as found in ChipsetMotherboard_TechDocs/48671.pdf on AMD's official support site.
Does anyone know more about this issue?Great! I've done that and now my card shows up. Thing is, when I try to get an IP address, it won't work. Here is the command output:
ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
And then it times out and no IP is assigned. The thing is, wpa_supplicant stays alive after this time out, and I am unable to kill it (killall -9 wpa_supplicant won't kill it). At this point if I try to reboot the machine, it will stop at 'Rebooting' and won't go anywhere. If I turn off the wireless card in its switch Linux crashes. If I try to get an ip again (by running dhcpcd) the command will hang and not return to the shell anymore.
I am unable to find any useful information in the logs.
Got any more suggestions?
Thanks! (And sorry to disturb so much) -
[SOLVED] Microphone does not work after fresh install
Hello all,
I just installed arch a week or so ago, everything is great except from
the fact that my microphone does not seem to work (at least with
skype)..
This is the output of amixer:
[jorge@flamingo ~]$ amixer
Simple mixer control 'Master',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum
Playback channels: Mono
Limits: Playback 0 - 64
Mono: Playback 57 [89%] [-5.25dB] [on]
Simple mixer control 'Headphone',0
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'Headphone',1
Capabilities: pvolume pswitch penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 64
Mono:
Front Left: Playback 64 [100%] [0.00dB] [on]
Front Right: Playback 64 [100%] [0.00dB] [on]
Simple mixer control 'PCM',0
Capabilities: pvolume penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 255
Mono:
Front Left: Playback 183 [72%] [-14.40dB]
Front Right: Playback 183 [72%] [-14.40dB]
Simple mixer control 'Mic Jack Mode',0
Capabilities: enum
Items: 'Mic In' 'Line In'
Item0: 'Mic In'
Simple mixer control 'IEC958',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'IEC958 Default PCM',0
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [on]
Simple mixer control 'IEC958 Playback Source',0
Capabilities: enum
Items: 'Digital Playback' 'ADAT' 'Analog Mux 1' 'Analog Mux 2' 'Analog Mux 3'
Item0: 'Digital Playback'
Simple mixer control 'IEC958',1
Capabilities: pswitch pswitch-joined penum
Playback channels: Mono
Mono: Playback [off]
Simple mixer control 'Beep',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined penum
Playback channels: Mono
Limits: Playback 0 - 3
Mono: Playback 0 [0%] [-18.00dB] [off]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 14
Front Left: Capture 14 [100%] [21.00dB] [on]
Front Right: Capture 14 [100%] [21.00dB] [on]
Simple mixer control 'Capture',1
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 14
Front Left: Capture 14 [100%] [21.00dB] [off]
Front Right: Capture 14 [100%] [21.00dB] [off]
Simple mixer control 'Capture',2
Capabilities: cvolume cswitch penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 14
Front Left: Capture 14 [100%] [21.00dB] [off]
Front Right: Capture 14 [100%] [21.00dB] [off]
Simple mixer control 'Digital',0
Capabilities: cvolume penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 120
Front Left: Capture 115 [96%] [27.50dB]
Front Right: Capture 115 [96%] [27.50dB]
Simple mixer control 'Input Source',0
Capabilities: cenum
Items: 'Mic' 'Front Mic' 'Digital Mic'
Item0: 'Mic'
Simple mixer control 'Input Source',1
Capabilities: cenum
Items: 'Mic' 'Front Mic' 'Digital Mic'
Item0: 'Mic'
Simple mixer control 'Input Source',2
Capabilities: cenum
Items: 'Mic' 'Front Mic' 'Digital Mic'
Item0: 'Mic'
Simple mixer control 'Mux',0
Capabilities: cvolume penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 4
Front Left: Capture 4 [100%] [40.00dB]
Front Right: Capture 4 [100%] [40.00dB]
Simple mixer control 'Mux',1
Capabilities: cvolume penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 4
Front Left: Capture 4 [100%] [40.00dB]
Front Right: Capture 4 [100%] [40.00dB]
Simple mixer control 'Mux',2
Capabilities: cvolume penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 4
Front Left: Capture 4 [100%] [40.00dB]
Front Right: Capture 4 [100%] [40.00dB]
[jorge@flamingo ~]$
The capture section seems to be ok.. However when I am using skype,
the people I call only hear a noise and nothing else. I confirmed that with
skype call testing service..
Moreover, the levels of the mixer are ok and nothing is muted.
Finally, the mic itself works fine, I dual boot with XP and I didn't have
any problems with skype there..
Please let me know what other information you need..
Many thanks in advance.
Last edited by geo909 (2011-02-23 01:23:28)alterecco wrote:
If you are using alsa, then remember to go into alsamixer and turn up your microphone volumes and set a device as the capture device.
Basically, go to the capture pane (F4), navigate to the capture device you want to use, and press Space to toggle it on.
First of all, I'm so sorry for the late reply.. I didn't have access to a pc for a long time.
And actually your suggestion did the job! I don't believe it was something that simple,
I spent hours googling around and trying all sorts of stuff..
Thanks a lot!!! -
Printer does not working after restart
I have installed HP LaserJet m1120 using hplip and hplip-plugin from AUR.
Everything was fine (printer worked) but after rebooting, printer doesn't working at all - cups doesn't "see" it and hp-testpage shows this:
# hp-testpage -i
warning: hp-testpage should not be run as root/superuser.
HP Linux Imaging and Printing System (ver. 3.12.10a)
Testpage Print Utility ver. 6.0
Copyright (c) 2001-14 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
| SELECT PRINTER |
Num CUPS Printer
0 HP_LaserJet_M1120_MFP
1 PhotoPrint
Enter number 0...1 for printer (q=quit) ?0
error: Unable to communicate with device (code=12): hp:/usb/HP_LaserJet_M1120_MFP?serial=MF12D9K
error: Unable to print to printer. Please check device and try again.
note: If an error occured, or the test page failed to print, refer to the HPLIP website
note: at: http://hplip.sourceforge.net for troubleshooting and support.
PhotoPrint is my second printer and it works fine.
What should i do? I have been trying to configure it for long time...
Last edited by Extravert (2012-11-17 14:46:06)Maybe, I haven't understood something but it still does not working.
I found that journalctl outputs some errors
Nov 17 22:57:06 trash-serv hp[405]: io/hpmud/pp.c 627: unable to read device-id ret=-1
Nov 17 22:57:06 trash-serv python2[406]: io/hpmud/pp.c 627: unable to read device-id ret=-1
And lsusb does not shows this printer
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Last edited by Extravert (2012-11-17 15:17:13) -
Wireless LAN does not work after restart
Hey
My brand new laptop suddenly went blank earlier today and when I restarted it I noticed my wireless internet won't work. It is also asking me to install some new driver, the Network Controller? I am confused as everything was working fine and suddenly it's not. Anyone any ideas? :-/Hi,
maybe you should try to install the driver for your wireless lan card. I mean, if some application damaged the driver or installed something which interferes with the wireless lan card then you should try to fix it with an reinstallation of the driver.
Heres a [LINK|http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp] to the drivers download page from Toshiba. Pick your model and your operating system and download the driver which fits for your wireless lan card.
Greets -
Oracle not work after restart compute
Hello
Whenever i restart my compute i got the error
ORA-12528: TNS:listener: all appropriate instances are blocking new connections
untill i restart the service from the services.
is there any solution for this
thanksSir,
This is my init.ora file
i am new in dba track
# Copyright (c) 1991, 2001, 2002 by Oracle Corporation
# Cache and I/O
db_block_size=8192
db_cache_size=25165824
db_file_multiblock_read_count=16
# Cursors and Library Cache
open_cursors=300
# Database Identification
db_domain=""
db_name=orcl
# Diagnostics and Statistics
background_dump_dest=E:\oracle\product\10.1.0\admin\orcl\bdump
core_dump_dest=E:\oracle\product\10.1.0\admin\orcl\cdump
user_dump_dest=E:\oracle\product\10.1.0\admin\orcl\udump
# File Configuration
control_files=("E:\oracle\product\10.1.0\oradata\orcl\control01.ctl", "E:\oracle\product\10.1.0\oradata\orcl\control02.ctl", "E:\oracle\product\10.1.0\oradata\orcl\control03.ctl")
db_recovery_file_dest=E:\oracle\product\10.1.0\flash_recovery_area
db_recovery_file_dest_size=2147483648
# Job Queues
job_queue_processes=10
# Miscellaneous
compatible=10.1.0.2.0
# Pools
java_pool_size=50331648
large_pool_size=8388608
shared_pool_size=93886080
# Processes and Sessions
processes=150
# Security and Auditing
remote_login_passwordfile=EXCLUSIVE
# Shared Server
dispatchers="(PROTOCOL=TCP) (SERVICE=orclXDB)"
# Sort, Hash Joins, Bitmap Indexes
pga_aggregate_target=25165824
sort_area_size=65536
# System Managed Undo and Rollback Segments
undo_management=AUTO
undo_tablespace=UNDOTBS1
thanks
Message was edited by:
Umesh Sharma
Message was edited by:
Umesh Sharma -
Microphone does not work in Facetime
Hi
I read other posts and in Maverik I didn't find simmilar problem, for most people their microphone does not work after few minutes, but in my case, microphone does not work at all in Facetime, so I can hear the other end, but they can not hear me! This happened after updating Mavericks.
My Mac specs:
Macbook Pro 2013
OSx 10.9.1 (Mavericks)
things I already tested:
I tried to use headphone and without headphone, but it didn't make any difference
Microphone works fine in Skype and other softwares (Audacity, YahooMessenger, etc.)
Tried with WiFi and with Ethernet cable
Internet speed is 2.3MBps
Router's firewall does not have any restriction for certain ports
Tried turning facetime Off and On
Tried to call iPhone 5s, iPad2 and MacBook Pro each in different network and different countries!
... and finally searching internet for hours (which obviously came up with nothing)
I'll be thankful if somebody help me through, all suggestions are welcome, so please don't hesitate to post.Same issue here....
8-core Mac Pro, Lion, Original External iSight camera connected via FireWire 400 through the FireWire jack on the 23" Apple Cinema Display.
Audio and video work fine using iChat and making video clips through any/all apps.
However, using FaceTime.....incoming audio and video are fine, outgoing video is fine, but outgoing audio is missing. Nobady can hear me.
Sorry guys...you can't doll this one up or spin it in any other direction......it's a bug pure and simple.
Feel free to fix it whilst you're dealing with all the other problems that Lion has.
....sT -
After upgrading to ios8 my 4s text dictation microphone does not work and is "greyed" out
After upgrading to ios8 my 4s text dictation microphone does not work and is "greyed" out. There is no function at all.
Ok I fixed the issue, turns out a couple of weeks ago, I downloaded a program that was suppose to help shrink some of your stuff to use less data, it was called Onavo. It was suppose to show you how much data you use to help keep you within your limits. If you have downloaded this, go through your settings and delete it and it will fix the problem. At least it did for me. I can now send photo's to non Iphone users via text no problem.
-
Satellite L870-165 does not work after being repaired by their service
Laptop Toshiba warranty does not work after being repaired by their service twice.
Model: Satellite L870-165
Computer will not boot, stays with black screen stating: No bootable device-Please restart your system
After reboot still happening the same.
I called Toshiba phone incident and after trying several options I said take him to repair the service.
They first told me it was the hard drive, then phoned me to indicate that reinstalling and finally it was the motherboard, which supposedly changed. The day after being picked computer repair returned to give exactly the same error, only malfunctioned one evening.
After another call to 902 the Toshiba warranty service, I went back to take the service, this time I changed the hard drive. When I got home the computer did not start even once, again gives the same error.
I believe that this team comes with a factory default so that its solution is not easy because even the technical service told me that I did not know what else to do with it.>Computer will not boot, stays with black screen stating: No bootable device-Please restart your system
This message pops up because the notebook cannot find the Windows system.
There could be either an problem with the HDD or maybe the HDD is OK but the Windows system isnt preinstalled properly.
You said that the service agent changed the HDD. But did someone install the Windows system?
You can try to do it yourself take your recovery disk (hopefully you created such disk in the past) and boot from the recovery disk in order to install the system.
In case booting from the Disk would not be possible, go to BIOS (F2) and disable the secure boot and change from UEFI to CSM mode -
Card slot does not work after update (14/10/2011)
Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
MacBook Pro 13 OS ver. 10.6.8Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks
-
[XP64] Microphone does not work in WinXP 64
Hi,In Windows XP 64bit my microphone does not work, tried it in Ventrilo 2., Skype and even in the Windows Recorder. The computer don't detect any sound. Offcourse?I have selected the microphone in the recordering section in the Windows volume panel and the volume at maxium. Also in the volume panel under playback the microphone is not mute, set to max volume. I have also installed WinXP 32bits and here it works OK with exactly the same settings. Thats why I think it is because of my Soundcard driver, I have installed the latest driver from this site. I have a SoundBlaster X-Fi Fatality. Is there anyone with a X-Fi soundcard with the same problem or anyone where the microphone works in WinXP 64bit's Or is it a known problem?Please help me
Hi Theicewarrior,?Creative support has been aware of this issue for quite some time (6+ months, maybe even a year). The 4GB+?RAM driver/addressing issues are not a priority or they would have been addressed quite some time ago.
Presumably this is due to functional Vista drivers for the masses being a higher priority than the relati'vely few of us with 4GB+ RAM and an X-Fi.
While the X-Fi?is a great card, my only wish was that the vendor was forthright about this product not functioning with certain configurations. It is my feeling that?making an effort to help?customers choose?products that will work with their configurations would result in satisfied and repeat customers?and a better bottom line?as opposed to?eeking a few extra dollars out of a slightly larger customer base and?who are then left unsatisfied with a product and unwilling to buy a company's products in the future.Message Edited by Foddan on 07-9-20070:45 AM -
My microphone does not work on calls on my iPhone 4
Don't ask me what has happened and I have been through all of the troubleshooting that I can on my own.
I have no clue how to get a hold of a LIVE AT&T person or APPLE person.
The problem is my microphone does not work when I use the telephone, whether I make the call or someone calls me. It is NOT the MUTE button. And yes, I have already rebooted my iPhone about 5 times now. Has not fixed it either.
But the microphone DOES work as I was able to record a new voicemail greeting to let people know my phone isn't working.
So, they could call me all day long but they won't hear me, so who do I call using my landline (thankfully I kept it).
It is the day after Thanksgiving and I would be a fool to head over to the Apple Store or the AT&T Store....
Thank-you,
MarciaTry disconnecting the headphones and then adjusting the volume, does it say headphones?
There might be something in the headphone jack, maybe lint, dirt, or something else in there.
Take a look at this Apple document for more information -> iPhone: Can't hear through the receiver or speakers -
"F11 System Recovery" during boot does not work after Cloning hard drive.
Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
Startup Menu (F11 System Menu works properly) only on original hard drive.
Following obtained from Disk Management & diskpart in Command Prompt.
GPT Disk <700GB>
Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
Partition 7 NTFS Primary 26MB/350MB [Recovery]
Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
Acronis True Image 2015
Acronis Backup for PC
AOMEI Backupper Professional
Macrium Reflect
Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
“Recovery
Your PC needs to be repaired
A required device isn’t connected or can’t be accessed.
Error code: 0xc0000225
You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
Thank you in advanced.Hi,
How did you clone the HDD ? One-for-one or different method ?
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
Recently installed Windows 7 on Pavilion dv6748us - internal microphone does not work
Hi,
sojo972 wrote:
I have been searching the web extensively, without success, to find how to resolve this issue.
I recently installed Windows 7, 32 bit, on my wife's HP Pavilion dv6748us laptop. Now her internal microphone does not work.
Have gotten some "roadside" advice to use a Windows Vista driver; Have no idea what the driver is or how to get it.
Have found some information about uninstalling realtek audio driver and reinstalling an older version; Have no idea on this one either.
Would really appreciate a definitive answer with a positive result.
Thanks for all help.
The drivers for the laptop are located here. select Vista and Driver-audio. The Vista driver should work. You can uninstall the driver from within the Device manager. Start --> type devmgmt.msc and the device manager will open. Locate the HD audio device and right-click it and update the driver.
After that is done go to Control Panel and Sound and the recording tab up top. Check to see if the microphone is grayed out. (not grayed out means driver is properly installed). The microphone should also have a green checkmark next to it. It is now a matter of selecting the microphone then selecting Properties to enable the microphone and then test and adjust the input level. Look at the tabs (listen,levels and advanced).
Had you considered trying Windows update or the Realtec website as a drivers source?
regards,
erico
regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience ConsumerHi:
Looking at your system information you could have one of two possible audio cards:
Conexant HD audio or the RealTek HD Audio
The fact that you couldn't install the RealTek HD audio driver indicates to me that you don't have a RealTek audio card. Check your device manager and look at your sound card and check to make sure which audio card you have.
Here is the Vista 32 bit driver for the Conexant audio card:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...
Here is the Vista 32 bit driver for the Realtek audio card:
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...
If you in fact have the Realtek audio card, I would download and install the latest, greatest HD driver directly from the RealTek site:
Accept the agreement, download and install the first one on the list. Maybe it has been updated to fix the issue you are experiencing.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=24&PFid=24&Level=4&Conn=3&DownT...
Paul -
RDP does not work after disabling TLS 1.0
RDP does not work after disabling TLS 1.0
Had to re-enable it .... what can i do to make it work with TLS 1.2 ??Hi,
Disabling TLS 1.0 will break RDP under default settings. Did the security scan say specifically to disable TLS 1.0? Normally you should be able to disable use of certain ciphers or prioritize ciphers. You may want to try IISCrypto, on
it you click the PCI button, then Apply button, then restart your server.
Additionally there are still a substantial number of web browsers in use that do not support TLS 1.1/1.2.
If you would like to continue with TLS 1.0 disabled you may change the RDP Security Layer. To do this please open Terminal Services Configuration (tsconfig.msc), double-click RDP-Tcp, change Security Layer to RDP Security Layer.
IMPORTANT: You are vulnerable to MITM attack when using RDP Security Layer because there is no Server Authentication. If you are running RDP over a VPN connection and there is no risk for interception then this may be okay. I recommend
you re-enable TLS 1.0 and have a ssl certificate from a public authority set on your RDP-Tcp listener.
Quoted from this thread answered
by TP, for more information you can go through that thread.
Hope it helps!
Thanks.
Dharmesh Solanki
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Maybe you are looking for
-
The only way I can carry on a search, is to click on Google, and that takes me to another screen, with a panel to type into, and that works fine.
-
Configuration Steps for Decentralized Adapter Engine
Hi all, What all configuration steps are required to make Adapter Engine as Decentralized AE. I have made required changes in SLD DataSupplier in Visual Administrator. what more configurations have to be done? On SAP XI Server and Decentralized Adapt
-
I am running Acrobat 9 and Word 2003. I want to export the .pdf file as a .doc file. This has worked in the past, but currently doesn't. I open the <file.pdf> file and then click export --> word. The document initialized but the OCR doesn't run.
-
Best practice recommendation for locale-specific text/labels
What is the recommended best practice approach to supporting locale-specific text for labels, messages when using Jdeveloper to create applets and applications. I am familiar with resource bundles, but wonder if there is a better approach within JDev
-
Unable to map a disk drive connected to the Airport Extreme
I just bought an Airport Extreme and connected a disk (Iomega Minimax) though the USB. I can see that the disk is connected (in the AirPort tool, and I can manually map it on my laptop (XP) using the IP-adress. Unfortunately I also have a PC (also an