Migration Assistant Update Problem

I have have an old G4 PowerBook running OS X 10.4.11 and want to migrate all the data to a new iMac running OS X 10.7.2. On the new machine it says to upgrade the migration assitant on the old machine. I have looked all over and anything I have found won't install b/c it says the machine does not qualify for the update. I also tried connecting the old machine to the new with a firewire but it does not appear on the new screen. I hate the idea of having to drag everything back to the store, any ideas how I can pull all the data off the old machine to the new, or how to upgrade the migration assistant on the old machine so the new machine recoginizes it?
Thanks

Did you use FireWire Target Disk Mode to start the PowerBook? Start the PowerBook while holdig teh t key, and keep holding until you seea display that looks something like this:
At that point, the hard drive of the PowerBook should be visible to the new Mac as an external hard drive. MA should work but, if it does not, you can still manually move items.
NOTE: by default, the Finder preferences may not allow external drive to show up on your new iMac. Go to Finder > Preferences and check the box for showing external hard drives:
When I upgraded to a 27-inch iMac (10.6.8) from a G4 MDD desktop Mac (10.4.11), I manually dragged the entire Documents folder from the G4 hard drive to the iMac. If you have already used the new Mac enough to have important files already in the new Documents folder. you may wish to do the dragging on a folder-by-folder basis, then file-by file. Takes longer but is very safe.
Note that OS 10.7 will not run older programs written for the PPC processors. If you have such programs, you need to upgrade them to versions with native Intel code. Example: Office 2004 will not run under Lion but Office 2008, that had both PPC and Intel code, will.
Due to the age and OS disparity between a PPC Mac running 10.4 and an Intel Mac running 10.7, you are better off to update programs than to use MA to migrate them.

Similar Messages

Migration assistant update for Mac OS X Snow Leopard

Hello -- I downloaded SNOW LEOPARD successfully that past week. I did a software update as well afterwards.
Now in preparation for upgrading to LION OS X, I read an article that mentions one must make sure to have the MIGRATION ASSISTANT UPDATE for Mac OS X Snow Leopard installed. I am unsure if this was included in the software updates I performed. One would assume it would be there. BUT there is not a detailed listing of what these combination updates include. HOW can I tell if I have the desired version required to continue on to LION?
Another suggestion was for one to perform FIRST AID on the start up disk. It only says to select your Mac HD and then to "verify" ..... do they mean to VERIFY DISK or VERIFY DISK PERMISSIONS. I have on occasion performed a REPAIR DISK PERMISSIONS but not the others mentioned. I do not know what the difference is?
THANK YOU

I have the same console mesages repeating ad-nasium as you do. What is interesting is I do have the StartuoItems directory but it is empty. The problem I have is that the log-in window comes up as normal, but I can not type in it for about 5-8 seconds. This has started after the latest updates which you mention. Don't know if this issue is related or not. Have deleted the loginwindows and loginitems preferences to no effect.

Migration Assistant Update

I am trying to install Migration Assistant Update for Mac OS X Lepard dated Aug 2011 on my MacBook Pro Ver. 10.6.8 in order to copy my files and folders over to my new MacBook Pro Lion. I downloaded the Migration assistant upgrade however when I try to install it I receive an installation error message: "Migration Assistant Update for Mac OS X Leopard can't be installed on this disk. This volume does not meet the requirements for the update" Why is this occuring?

steve626 wrote:
As a point of clarification, I believe this statement is incorrect. Migration Assistant (and Setup Assistant) are in fact designed to migrate from an older system to a newer one, and I would guess this is the most common use.
That's correct.
Setup Assistant and Migration Assistant will transfer from an older "major version" of OSX to the same or a newer one, such as Snow Leopard to Lion or Lion to Lion.
It will also transfer from any "minor" version to any other "minor" version within the same major version, such as 10.6.0 to 10.6.8, or 10.6.8 to 10.6.0 (although it's not recommended to go backwards, as in some cases file systems have been changed and some apps won't work properly).

Migration assistant restore problem with time capsule

Hi People,
I have the weirdest of all problems. Let me explain what happend and you will be as amazed as I am now.
======
I have been using a 2TB time capsule for about a year and a half now. Every day for 18 months everything was being backupt. Everything smooth no problem.
My 27" iMac needed a fresh install at home because I have been upgrading from SL to Lion and thing got a bit odd. So this is what I did in a nut shell.
1. Bought a new 27" iMac Quad core with 12 Gb ram etc. (I bought it for my office)
2. At home started up the new iMac and the migration assisant asked me what I wanted.
3. Did a full restore from the TC and all my user data was restore to the new iMac!
=== Hurray so far, evrything worked liked it should.===
This was my test, now I was confident to erase my "old" iMac and do a full Lion reinstall and then use migration assisant to restore all files.
It worked with the new iMac so nothing to loose.
So I erased the new iMac, boxed it again and took it to the office.
Now It was time for my old iMac to be reinstalled.
=====
4. So I erased my "old" iMac.
5. Did a clean Lion install from DvD.
6. Did all software updates (as I had done with the new iMac).
7. started Migration Assistant
8. Pointed to the time capsule and did everything like the day before
9. Got an error message.
=====
***?? I tested this it should work. Now ALL my data is gone. All my movies, honeymoon, kids growing up, etc etc etc etc.
Everything gone gone gone!
So now I can browse to the TC and see the sparsebundle file. It is 1.5TB. I can show package contents and see the files, I can go into the "Bands" dir. and see a bunch of files. But I can not repair, mount, use disk utils with the sparsebundle.
The data must be in the 1.5 Tb file but I have no way of accessing it.
I need some good advice / help from someone because my whole family history is gone at this moment .

Woxxxxxx wrote:
My 27" iMac needed a fresh install at home because I have been upgrading from SL to Lion and thing got a bit odd.
That's usually the last thing to try. Depending on what was wrong, simply installing a fresh version of OSX would be likely to fix it. If not, finding and addressing the actual problem would probably be much better than starting with the "nuclear" option.
5. Did a clean Lion install from DvD.
6. Did all software updates (as I had done with the new iMac).
7. started Migration Assistant
It's much better to use Setup Assistant when your Mac first starts up after installing OSX, to prevent Problems after using Migration Assistant.
9. Got an error message.
Was that the "some backups cannot be opened" message? If so, try to repair them, per #A5 in Time Machine - Troubleshooting.

Forms Migration Assistant installation problem

Hi,
I'm trying to install Forms Migration Assistant on linux to convert forms 6i apps to forms 9i. But when i try to install FMA downloaded from here the installer says that the Oracle Home does not have Oracle Forms 9i installed altough it was shown in installed products. The output of the log file is below. Please if anyone know the solution for this problem or have any idea it would be so helpful.
I need it for my thesis to be given this week.
Thanks for your help.
oraInstall2003-07-19_10-20-14AM.err
Exception java.lang.NullPointerException occurred..
java.lang.NullPointerException
at oracle.sysman.oii.oiic.OiicInstallSession.getLibLoader(OiicInstallSession.java:4614)
at oracle.sysman.oii.oiic.OiicInstallSession.getDialogLibLoader(OiicInstallSession.java:4447)
at oracle.sysman.oii.oiif.oiifb.OiifbWizChainDlgElem.loadDialog(OiifbWizChainDlgElem.java:1394)
at Components.ifplsqlconv90.v9_0_2_10_1.CompContext.initialize_Dialog2(Unknown Source)
at Components.ifplsqlconv90.v9_0_2_10_1.CompContext.initializeDialog(Unknown Source)
at oracle.sysman.oii.oiif.oiifb.OiifbCompWizChainDlgElem.initialize(OiifbCompWizChainDlgElem.java:40)
at oracle.sysman.oii.oiif.oiifb.OiifbCondIterator.iterate(OiifbCondIterator.java:129)
at oracle.sysman.oii.oiis.OiisCompContext.doOperation(OiisCompContext.java:1062)
at oracle.sysman.oii.oiif.oiifb.OiifbLinearIterator.iterate(OiifbLinearIterator.java:116)
at oracle.sysman.oii.oiic.OiicCompsWizEngine.doOperation(OiicCompsWizEngine.java:172)

Also in the installation log file it says the things below. I think it's because i cannot identify the FORMS_ORACLE_HOME variable. In the installation procedure of FMA it says that i should set FORMS90_PATH to $ORACLE_HOME/forms90 but it doesn't work either.
*** Component Locations Page***
ShowCompLocs = SHOW_COMPONENT_LOCATIONS_PAGE = true
Entering component: ifplsqlconv90 installation
Setting value of O_JDK_HOME to
Setting value of FORMS_ORACLE_HOME to
*** Warning Page***
TitleLabel = Warning
SubTitleLabel =
InfoLabel = It appears that you have selected an Oracle Home that does not have
Oracle9i Forms installed.
Please press the 'Previous' button and select an Oracle Home that does contain F
orms.
Setting value of SHOW_COMPONENT_LOCATIONS_PAGE to true
*** Install Page***
Starting install install phase 1 of component Oracle9i Forms Migration Assistant
Starting install link phase of component Oracle9i Forms Migration Assistant
Starting install install phase 2 of component Oracle9i Forms Migration Assistant
Initializing installer save inventory WCCE
Unable to read /opt/devsuite/oraInventory/Contents/LibsList.ser. Some inventory
information may be lost.

Migration Assistant/FireWire problems.... I'm not sure which

I've searched through many of the posts on this subject and I've not found anything similar so I thought that I'd try posting the question.
My lovely wife just bought me a new iMac for my birthday to replace my very old and very abused (also read... incredibly slow iBook G4). I didn't do MA when I first booted it up as I didn't own a FireWire then.
I just bought a FireWire yesterday, plugged it in to both computers and brought up the MA program. It seemed to recognize that that a computer was connected to the other end as it told me to reboot it into "FireWire" mode. I did that and then it never could hook up to the computer again. I've attempted it many different ways and times.
Frankly I'm at the end of my rope and I've been transferring files via BlueTooth just to get some of my old stuff on the new machine.
Hopefully, this is an easy problem for someone out there.

Also if you read in the back posts, Migration Assistant doesn't work well between PowerPC and Intel Macs:
http://discussions.apple.com/thread.jspa?threadID=435350&tstart=10
I would say one of the symptoms is just as you've said, it basically times out forever.
Please don't post any more "me toos". If you have a problem and it is not related to solving the original poster's thread, there is a way to post a new topic in this link:
http://discussions.apple.com/forum.jspa?forumID=1219&start=0
You'll get a wider audience, and won't confuse the original poster with solutions that don't apply to them.

Migration Assistant update not following through

I am trying to migrate the contents of my 10.4.11 Tiger to a new MacBook. It says I need to update the Migration Assistant on my Tiger. I have downloaded and installed this, http://support.apple.com/kb/DL713. IT seems to work smoothly, but the Migration Assistant on my Tiger is still 1.06, and I cannot get my two computers to connect to each other through the Assistant. What am I doing wrong?

Correct, the method that requires using MA on both Computers will not work with Tiger/10.4.x
If both of these have Firewire it can be done running only MA on the new Mac & the older one in Target mode...
http://support.apple.com/kb/HT1661
Then in MA choode from another Disk or such wording.

Migration Assistant Network Problem ?

I have been running Migration Assistant for about 2 days now using firewire from MacBook Pro to iMac Now it keeps coming up with "Might be problem with network" I have checked all passwords reset Router and Time Machine and both computers are able to communicate through them It now says about 12 hrs 33 min remaining and sticks at that but still "Might be problem with network" If I shutdown and reboot both computers will it start from where it left off or at the beginning again? Help please !!

RickAu wrote:
The iMac just stays saying "waiting for other Mac to restart". I have checked all connections re-set router and Time Capsule Made sure that all passwords are correct re-booted both computers.
This setup should just be using a Firewire cable connected between the two Macs, with the iMac running Migration Assistant & the other Mac in FireWire target disk mode. Networking connections & devices like Airport, Time Capsule, routers, etc. should have nothing to do with it.
For this setup, make sure you choose the Migration Assistant option to transfer data 'From a Time Machine backup or other disk' & not either of the options that mention a Mac on a network. Before you start Migration Assistant, put the other Mac in target mode & make sure it shows up in Finder.

Migration Assistant INSTALL Problem

Having not been able to run, on my Windows 98 machine, oa2owiz-
8_1_5_0_0.exe downloaded from this site, OTN sent me the free CD-
ROM version, along with Oracle8i disk set for Windows NT (sic!).
The later with just to give me the the Universal Installer.
1) I unzipped using oa2owiz-8_1_5_0_0.exe FROM THE CD (does
this make a difference).
I first unzipped to my Oracle install directory, so
everything installed in D:\orawin95\TEMP
When I ran into the problem described below, I unzipped
FROM THE CD into the suggested default: C:\WINDOWS\TEMP. Both
ways, I get the same problem:
2) When I put in the Oracle8i CD and executed setup.exe (thereby
launching the Universal Installer) and then
3) pointed the installer to (either of the above) directories
on my machine with the products.jar file that was just
unzipped. When I hit 'Next' I get:
"Invalid staging are. There are no top level components for
Windows 98 available to install from this staging area."
FWIW: The above message message would appear, after the install
thermometer appeared briefly, if I used the full path to
the .jar, for instance C:\WINDOWS\TEMP\products.jar.
If I omitted the file name, I wouldn't even get the thermometer,
and the (sooner appearing-no thermometer) message was:
"There was a problem opening the staging area.
Please make sure the 'Source' you have specified is valid."
Am I doing something wrong?
Thanks >>>>>> Robert
null

Hi Robert !
The Oracle Migration Assistant for MS Access is not supported and
thus not installable under Windows 98.
It is only installable under Windows NT and Windows 95.
Thanks
- Garry
Robert R. Wagner (guest) wrote:
: Having not been able to run, on my Windows 98 machine, oa2owiz-
: 8_1_5_0_0.exe downloaded from this site, OTN sent me the free
CD-
: ROM version, along with Oracle8i disk set for Windows NT
(sic!).
: The later with just to give me the the Universal Installer.
: 1) I unzipped using oa2owiz-8_1_5_0_0.exe FROM THE CD (does
: this make a difference).
: I first unzipped to my Oracle install directory, so
: everything installed in D:\orawin95\TEMP
: When I ran into the problem described below, I unzipped
: FROM THE CD into the suggested default: C:\WINDOWS\TEMP. Both
: ways, I get the same problem:
: 2) When I put in the Oracle8i CD and executed setup.exe
(thereby
: launching the Universal Installer) and then
: 3) pointed the installer to (either of the above) directories
: on my machine with the products.jar file that was just
: unzipped. When I hit 'Next' I get:
: "Invalid staging are. There are no top level components for
: Windows 98 available to install from this staging area."
: FWIW: The above message message would appear, after the install
: thermometer appeared briefly, if I used the full path to
: the .jar, for instance C:\WINDOWS\TEMP\products.jar.
: If I omitted the file name, I wouldn't even get the
thermometer,
: and the (sooner appearing-no thermometer) message was:
: "There was a problem opening the staging area.
: Please make sure the 'Source' you have specified is valid."
: Am I doing something wrong?
: Thanks >>>>>> Robert
null

Migration assistant unusual problem

Hey guys,
So I bought a refurb 2011 15' mbp recently and i was trying to transfer files from my 2008 aluminum macbook running lion (10.7.4). Because migration assistant told me it could not transfer files from my old computer (which was running newer software) to my new 15' pro I set up the new mbp, updated the software and then got my free download of mountain lion. After that was done I connected the two computers via ethernet and ran migration assistant. Everything went well, the files transferred (I moved every file including my user account) but at the very end it told me that there was a file that couldn't be transferred (it was something like Error: 2012 Firstname Lastname --> my user account 8-5-2012 - 00000011 was not compatible). On my old computer it did not display any error messages, according to it my files had transferred successfully. When I logged back into the admin account on my NEW computer, it looked like only the applications and some pictures made it through. No documents, media or settings. Migration assistant DID NOT create a separate account on my new computer but the odd thing is that when I looked up the disk space available on my NEW computer it showed that the HD had been filled with something but it was classifed as "other" (under about this mac --> available storage). What do you guys think went wrong and is there anything I can do to fix it without wiping the HD and starting over? Thanks!

RickAu wrote:
The iMac just stays saying "waiting for other Mac to restart". I have checked all connections re-set router and Time Capsule Made sure that all passwords are correct re-booted both computers.
This setup should just be using a Firewire cable connected between the two Macs, with the iMac running Migration Assistant & the other Mac in FireWire target disk mode. Networking connections & devices like Airport, Time Capsule, routers, etc. should have nothing to do with it.
For this setup, make sure you choose the Migration Assistant option to transfer data 'From a Time Machine backup or other disk' & not either of the options that mention a Mac on a network. Before you start Migration Assistant, put the other Mac in target mode & make sure it shows up in Finder.

Migration Assistant Filemaker problem

Hello, can anyone help,
Here at work I've just got a faster Mac, i transferred my user account from the old machine with Migration Assistant.
If i open a local file everything is fine, but if i open a remote file from our FMP server it starts to load then crashes FMP
If i log-on with the original account from the faster machine everything is fine, i deleted all the FMP prefs, keychains and re-installed FMP9, still crashes!!!
I also called FMP support but they don't know
Anybody got any ideas?
Thanks
Ian

What I'd try is, open a local file, save it remotely, quit FMP, restart, try loading the remote file you just saved, if that works, compare Permissions on one that does & one that doesn't.

Migration Assistant Connectivity Problem

My MBP(OSX 10.5.8) will not connect to my new iMac to complete the Migration Assistant. Any help would be greatly appreciated!

I have tried connecting them via ethernet cable. But I have yet to have any luck. I was contemplating buying a firewire and trying the whole "target disk" method. But I wanted to make sure I couldn't do it with my ethernet cable first!

Download Assistant update problem

The version I currently have on my computer is 1.0.6. It is not letting up update the download assistant and is saying that it has been mis-configured. How do I fix this problem?

You would suggest uninstall Adobe Download Assistant. You can follow the steps suggested in below link.
http://forums.adobe.com/message/3980244
Go to Adobe.com and start over again by clicking the "Download Now" button for the product trial.

Migration assistant -- causing problems on new iMac?

I got a new 20" iMac yesterday. Specs are 2.16Ghz, 1 gig RAM, 128 meg video memory. I transferred all my settings and data from my mini using the mini in target disk mode with the firewire connection. I've had to reinstall a couple of drivers but other than that everything seems to have transferred fine. However, the iMac seems sluggish at many tasks and is doing some quirky things. A good example is that right now, I just mapped a drive on my Windows PC and it mapped fine but the "Connecting to Server" status window is still up and won't go away. It also seems to be slow opening some apps, etc. Could transferring everything from my mini have caused this? Would it be better to just reinstall OSX clean and install everything from scratch? Could the problems be because I migrated from a PPC Mac to an Intel?
I have 2 gigs of RAM on order so I know that will help but this seems like a bigger problem than just a lack of memory...
Thanks
Todd

Thanks for the feedback. Glad you fixed the problem. Now, get a bootable, external HD, and make a bootable backup/clone, using Carbon Copy Cloner, SuperDuper!, etc. That will mitigate future problems when updating stuff.
See:
http://www.macattorney.com/ts.html
http://www.macmaps.com/upgradefaq.html and
http://www.thexlab.com/faqs/installswupdates.html
for more information.

Migration Assistant DL problem

Re: Access to Oracle
From: Robert R. Wagner (guest)
Email: [email protected]
Date: Thu Jul 15 17:04 CDT 1999
I downloaded oa2owiz-8_1_5_0_0.exe last, but it won't run
on my machine (Windows 98 Pentium II 400 MHz). The error message
is " ... oa2owiz-8_1_5_0_0.exe is not a valid Win32 application".
It took over two hours to download this file. PLEASE don't tell
me I need to download it again!!
Thanks >>>>>> Robert
null

Hi !
The Oracle Assistant for MS Access is not supported, and thus
cannot be installed, under Windows 98. It is supported and
installable under Windows NT and Windows 95 only.
Thanks !
Oracle Migration Workbench Team wrote:
: Yes,
: That is another alternative. The CDROM is free and
: does contain the MS Access wizard also.
: As an FYI, we have come up with a method of splitting
: up the download into small chunks and will be implementing
: this in the very near future to resolve these download
: problems.
: My apologies,
: Marie
: Robert R. Wagner (guest) wrote:
: : I asked a friend to try downloading the Migration Wizard. He
: did
: : it TWICE. Both times, he got the "...is not a valid Win32
: : application." message when he try to run the .exe.
: : This is on a different machine (not networked to mine),
: : different incompetencies, etc. Can this be just a
coincidence?
: : An earlier thread contained a MWT response that included:
: : "The Migration Companion CD-ROM, which can be ordered FREE
: : from any Oracle sales office, #Z24203, does contain the
: : MS Access wizard."
: : Does that CD-ROM contain the latest version of the wizard?
: : Thanks >>>>>> Robert
: : Oracle Migration Workbench Team wrote:
: : : The Migration Wizard is a completely free product and
: : : no licensing is required. However, it is not actually
: : : on the 8i CD. This is the first time that I have seen
: : : these types of problems with the web download however I
: : : will look into splitting up the product into smaller
: : : chunks for future downloads.
: : : Regards,
: : : Marie
: Oracle Technology Network
: http://technet.oracle.com
null

Migration Assistant Update Problem

Similar Messages

Maybe you are looking for