Migration to CUBE and SIP
Hi all,
I will be migrating from MGCP PRI over to SIP in the coming month and was trying to find out if I can use my 3945 to do both the CUBE and the PRI gateway functions at the same time while I'm doing the migration. I can always revert to an old 2811 if needed, but was wondering if it was possible.
CUCM version is 8.6 and router IOS is 15.0(1r)M16,
I will have the license before I start. Thanks muchly for the answer... there may be more questions coming!
Similar Messages
-
I have a H.323 gateway. I want to know if I can configure this existing h.323 gateway as a Cube to transport SIP.
If so do I need to bind a seperate interface to SIP and H.323 or the same interface can be used for both
Can the Gateway be registered as h.323 to CCM1 and Can I have a SIP trunk between the same Gateway to CCM2?
Thanks in advanceHi,
"I have a H.323 gateway. I want to know if I can configure this existing h.323 gateway as a Cube to transport SIP".
A CUBE gateway by definition is a voice gateway that connects ip-2-ip calls and plus some extra fancy features. The gateway can support both h.323 and sip at the same time.
"If so do I need to bind a separate interface to SIP and H.323 or the same interface can be used for both"
This is tricky question, the answer is I don't know but why limit yourself when you can bind them into different loopback interfaces.
"Can the Gateway be registered as h.323 to CCM1 and Can I have a SIP trunk between the same Gateway to CCM2?"
Absolutely. -
Unable to place call on calls on hold - SIP Trunk from CUCM to CUBE and from CUBE to ISTP
Hi Cisco Community,
I have a SIP Trunk setup between the CUCM and CUBE and another SIP Dial Peers from the CUBE to the ITSP. All incoming/outgoing calls, DTMF-Relay works well except one thing which is the ability to hold the call.
On the SIP Trunk from the CUCM to the CUBE, I did not select “MTP” because when I do so, I am forced to select my preferred MTP codec which when selected G.729/G.729a, all my outgoing calls goes out using G.729r8. This codec works well for most of the calls until the ITSP replies back with G.729br8. When this condition occur, my call simply fails (this is very intermittent and only some random numbers).
That said, I have some issues with DTMF Relay when I select MTP on the SIP Trunk. DTMF Relay only works if the call is G.729r8 all the way from the CUCM to the ITSP. If the ITSP replies back with G.729br8, the call might established but will simply be “voice-only”.
The current setup is no MTP is selected and everything is working perfectly. I am happy with that until I place a call on hold, which when I do so, the call immediately terminate. Could you please help me understand why?
I have all media resources configured such as G.729r8 MTP, G.729br8 MTP, G.711u MTP, Transcoding with all codecs, etc. All MRG and MRGL are configured on all devices and SIP Trunks.
Below is an example of a call that is connected with the current setup:
Note:
IP: 10.18.81.2 (CUBE)
IP: 10.18.81.11 (CUCM SUB)
IP: 10.111.111.254 (ITSP SBC)
PM-HO-VG-01#
PM-HO-VG-01#
Nov 30 11:44:29.938: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72063a5aba5d
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>
Date: Sun, 30 Nov 2014 11:44:29 GMT
Call-ID: [email protected]
Supported: timer,resource-priority,replaces
Min-SE: 1800
User-Agent: Cisco-CUCM9.1
Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
CSeq: 101 INVITE
Expires: 180
Allow-Events: presence, kpml
Supported: X-cisco-srtp-fallback,X-cisco-original-called
Call-Info: <sip:10.18.81.11:5060>;method="NOTIFY;Event=telephone-event;Duration=500"
Cisco-Guid: 1020645888-0000065536-0000124117-0189862410
Session-Expires: 1800
Contact: <sip:[email protected]:5060>
Max-Forwards: 70
Content-Length: 0
Nov 30 11:44:29.942: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72063a5aba5d
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>
Date: Sun, 30 Nov 2014 11:44:29 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-15.2.4.M5
Content-Length: 0
Nov 30 11:44:29.946: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>
Date: Sun, 30 Nov 2014 11:44:29 GMT
Call-ID: [email protected]
Supported: 100rel,timer,resource-priority,replaces,sdp-anat
Min-SE: 1800
Cisco-Guid: 1020645888-0000065536-0000124117-0189862410
User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
CSeq: 101 INVITE
Timestamp: 1417347869
Contact: <sip:[email protected]:5060>
Call-Info: <sip:10.18.81.2:5060>;method="NOTIFY;Event=telephone-event;Duration=2000"
Expires: 180
Allow-Events: telephone-event
Max-Forwards: 69
Session-Expires: 1800
Content-Type: application/sdp
Content-Disposition: session;handling=required
Content-Length: 301
v=0
o=CiscoSystemsSIP-GW-UserAgent 7676 6958 IN IP4 10.18.81.2
s=SIP Call
c=I
PM-HO-VG-01#N IP4 10.18.81.2
t=0 0
m=audio 22256 RTP/AVP 18 0 8 101
c=IN IP4 10.18.81.2
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=yes
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-16
Nov 30 11:44:29.950: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>
Call-ID: [email protected]
CSeq: 101 INVITE
Timestamp: 1417347869
Nov 30 11:44:30.658: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 180 Session Progress
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Call-ID: [email protected]
CSeq: 101 INVITE
Timestamp: 1417347869
Supported:
Contact: <sip:[email protected]:5060;transport=udp>
Session: Media
Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
X-BroadWorks-Correlation-Info: bbf94839-a234-4237-95e6-a7037322f0f4
Content-Type: application/sdp
Content-Length: 355
v=0
o=BroadWorks 316169737 1 IN IP4 10.111.111.254
s=-
c=IN IP4 10.111.111.254
t=0 0
m=audio 20074 RTP/AVP 18 101 100
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:100 X-NSE/8000
a=fmtp:100 200-202
a=X-sqn:0
a=X-cap: 1 audio RTP/AVP 100
a=X-cpar: a=rtpmap:100 X-NSE/8000
a=X-cpar: a=fmtp:100 200-202
a=X-cap: 2 image udptl t38
Nov 30 11:44:30.662: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 183 Session Progress
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72063a5aba5d
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:29 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Contact: <sip:[email protected]:5060>
Supported: sdp-anat
Server: Cisco-SIPGateway/IOS-15.2.4.M5
Content-Type: application/sdp
Content-Disposition: session;handling=required
Content-Length: 289
v=0
o=CiscoSystemsSIP-GW-UserAgent 7965 2747 IN IP4 10.18.81.2
s=SIP Call
c=IN IP4 10.18.81.2
t=0 0
m=audio 22350 RTP/AVP 18 101 19
c=IN IP4 10.18.81.2
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=yes
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:19 CN/8000
a=ptime:20
Nov 30 11:44:31.226: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 180 Session Progress
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Call-ID: [email protected]
CSeq: 101 INVITE
Timestamp: 1417347869
Supported:
Contact: <sip:[email protected]:5060;transport=udp>
Session: Media
Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
X-BroadWorks-Correlation-Info: bbf9
PM-HO-VG-01#4839-a234-4237-95e6-a7037322f0f4
Content-Type: application/sdp
Content-Length: 355
v=0
o=BroadWorks 316169737 1 IN IP4 10.111.111.254
s=-
c=IN IP4 10.111.111.254
t=0 0
m=audio 20074 RTP/AVP 18 101 100
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:100 X-NSE/8000
a=fmtp:100 200-202
a=X-sqn:0
a=X-cap: 1 audio RTP/AVP 100
a=X-cpar: a=rtpmap:100 X-NSE/8000
a=X-cpar: a=fmtp:100 200-202
a=X-cap: 2 image udptl t38
Nov 30 11:44:31.630: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC72218
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Call-ID: [email protected]
CSeq: 101 INVITE
Timestamp: 1417347869
Supported:
Contact: <sip:[email protected]:5060;transport=udp>
Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
Accept: application/media_control+xml,application/sdp,application/xml
X-BroadWorks-Correlation-Info: bbf94839-a234-4237-95e6-a7037322f0f4
Content-Type: application/sdp
Content-Length: 355
v=0
o=BroadWorks 316169737 1 IN IP4 10.111.111.254
s=-
c=IN IP4 10.111.111.254
t=0 0
m=audio 20074 RTP/AVP 18 101 100
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:100 X-NSE/8000
a=fmtp:100 200-202
a=X-sqn:0
a=X-cap: 1 audio RTP/AVP 100
a=X-cpar: a=rtpmap:100 X-NSE/8000
a=X-cpar: a=fmtp:100 200-202
a=X-cap: 2 image udptl t38
Nov 30 11:44:31.630: //64511/3CD5D2000001/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x0x3D7B1458
State of The Call : STATE_ACTIVE
TCP Sockets Used : NO
Calling Number : 27218091323
Called Number : 0862000000
Source IP Address (Sig ): 10.18.81.2
Destn SIP Req Addr:Port : 10.111.111.254:5060
Destn SIP Resp Addr:Port : 10.111.111.254:5060
Destination Name : 10.111.111.254
Nov 30 11:44:31.630: //64511/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : g729br8
Negotiated Codec Bytes : 20
Nego. Codec payload : 18 (tx), 18 (rx)
Negotiated Dtmf-relay : 6
Dtmf-relay Payload : 101 (tx), 101 (rx)
Source IP Address (Media): 10.18.81.2
Source IP Port (Media): 22256
Destn IP Address (Media): 10.111.111.254
Destn IP Port (Media): 20074
Orig Destn IP Address:Port (Media): [ - ]:0
Nov 30 11:44:31.630: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
ACK sip:[email protected]:5060;transport=udp SIP/2.0
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC81D00
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Date: Sun, 30 Nov 2014 11:44:29 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 101 ACK
Allow-Events: telephone-event
Content-Length: 0
Nov 30 11:44:31.634: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72063a5aba5d
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:29 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Contact: <sip:[email protected]:5060>
Supported: replaces
Supported: sdp-anat
Server: Cisco-SIPGateway/IOS-15.2.4.M5
Supported: timer
Content-Type: application/sdp
Content-Disposition: session;handling=required
Content-Length: 289
v=0
o=CiscoSystemsSIP-GW-UserAgent 7965 2747 IN IP4 10.18.81.2
s=SIP Call
c=IN IP4 10.18.81.2
t=0 0
m=audio 22350 RTP/AVP 18 101 19
c=IN IP4 10.18.81.2
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=yes
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:19 CN/8000
a=ptime:20
Nov 30 11:44:31.726: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
ACK sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72075e3a02c1
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:29 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 101 ACK
Allow-Events: presence, kpml
Content-Type: application/sdp
Content-Length: 236
v=0
o=CiscoSystemsCCM-SIP 9082578 1 IN IP4 10.18.81.11
s=SIP Call
c=IN IP4 10.18.80.40
b=TIAS:8000
b=AS:8
t=0 0
m=audio 21928 RTP/AVP 18 101
a=rtpmap:18 G729/8000
a=ptime:20
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
Nov 30 11:44:31.730: //64510/3CD5D2000001/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x0x3D816D70
State of The Call : STATE_ACTIVE
TCP Sockets Used : NO
Calling Number : 0218091323
Called Number : 0862000000
Source IP Address (Sig ): 10.18.81.2
Destn SIP Req Addr:Port : 10.18.81.11:5060
Destn SIP Resp Addr:Port : 10.18.81.11:5060
Destination Name : 10.18.81.11
Nov 30 11:44:31.730: //64510/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : g729br8
Negotiated Codec Bytes : 20
Nego. Codec payload : 18 (tx), 18 (rx)
Negotiated Dtmf-relay : 6
Dtmf-relay Payload : 101 (tx), 101 (rx)
Source IP Address (Media): 10.18.81.2
Source IP Port (Media): 22350
Destn IP Address (Media): 10.18.80.40
Destn IP Port (Media): 21928
Orig Destn IP Address:Port (Media): [ - ]:0
Nov 30 11:44:31.730: //64510/3CD5D2000001/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x0x3D816D70
State of The Call : STATE_ACTIVE
TCP Sockets Used : NO
Calling Number : 0218091323
Called Number : 0862000000
Source IP Address (Sig ): 10.18.81.2
Destn SIP Req Addr:Port : 10.18.81.11:5060
Destn SIP Resp Addr:Port : 10.18.81.11:5060
Destination Name : 10.18.81.11
PM-HO-VG-01#
Nov 30 11:44:31.730: //64510/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : g729br8
Negotiated Codec Bytes : 20
Nego. Codec payload : 18 (tx), 18 (rx)
Negotiated Dtmf-relay : 6
Dtmf-relay Payload : 101 (tx), 101 (rx)
Source IP Address (Media): 10.18.81.2
Source IP Port (Media): 22350
Destn IP Address (Media): 10.18.80.40
Destn IP Port (Media): 21928
Orig Destn IP Address:Port (Media): [ - ]:0
PM-HO-VG-01#sh sip
PM-HO-VG-01#sh sip-ua call
PM-HO-VG-01#sh sip-ua calls
Total SIP call legs:2, User Agent Client:1, User Agent Server:1
SIP UAC CALL INFO
Call 1
SIP Call ID : [email protected]
State of the call : STATE_ACTIVE (7)
Substate of the call : SUBSTATE_NONE (0)
Calling Number : 27218091323
Called Number : 0862000000
Bit Flags : 0xC04018 0x10000100 0x0
CC Call ID : 64511
Source IP Address (Sig ): 10.18.81.2
Destn SIP Req Addr:Port : [10.111.111.254]:5060
Destn SIP Resp Addr:Port: [10.111.111.254]:5060
Destination Name : 10.111.111.254
Number of Media Streams : 1
Number of Active Streams: 1
RTP Fork Object : 0x0
Media Mode : flow-through
Media Stream 1
State of the stream : STREAM_ACTIVE
Stream Call ID : 64511
Stream Type : voice+dtmf (0)
Stream Media Addr Type : 1
Negotiated Codec : g729br8 (20 bytes)
Codec Payload Type : 18
Negotiated Dtmf-relay : rtp-nte
Dtmf-relay Payload Type : 101
QoS ID : -1
Local QoS Strength : BestEffort
Negotiated QoS Strength : BestEffort
Negotiated QoS Direction : None
Local QoS Status : None
Media Source IP Addr:Port: [10.18.81.2]:22256
Media Dest IP Addr:Port : [10.111.111.254]:20074
Options-Ping ENABLED:NO ACTIVE:NO
Number of SIP User Agent Client(UAC) calls: 1
SIP UAS CALL INFO
Call 1
SIP Call ID : [email protected]
State of the call : STATE_ACTIVE (7)
Substate of the call : SUBSTATE_NONE (0)
Calling Number : 0218091323
Called Number : 0862000000
Bit Flags : 0xC0401E 0x10000100 0x80004
CC Call ID : 64510
Source IP Address (Sig ): 10.18.81.2
Destn SIP Req Addr:Port : [10.18.81.11]:5060
Destn SIP Resp Addr:Port: [10.18.81.11]:5060
Destination Name : 10.18.81.11
Number of Media Streams : 1
Number of Active Streams: 1
RTP Fork Object : 0x0
Media Mode : flow-through
Media Stream 1
State of the stream : STREAM_ACTIVE
Stream Call ID : 64510
Stream Type : voice+dtmf (1)
Stream Media Addr Type : 1
Negotiated Codec : g729br8 (20 bytes)
Codec Payload Type : 18
Negotiated Dtmf-relay : rtp-nte
Dtmf-relay Payload Type : 101
QoS ID : -1
Local QoS Strength : BestEffort
Negotiated QoS Strength : BestEffort
Negotiated QoS Direction : None
Local QoS Status : None
Media Source IP Addr:Port: [10.18.81.2]:22350
Media Dest IP Addr:Port : [10.18.80.40]:21928
Options-Ping ENABLED:NO ACTIVE:NO
Number of SIP User Agent Server(UAS) calls: 1
PM-HO-VG-01#
PM-HO-VG-01#
PM-HO-VG-01#
As you can see, the call is connected and everything is working perfectly. When I press the hold button, here is what I get:
NOTE: I have # debug ccsip messages and #debug ccsip calls (running)
PM-HO-VG-01#
PM-HO-VG-01#
Nov 30 11:44:49.210: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720852ab8b92
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
Supported: timer,resource-priority,replaces
Min-SE: 1800
User-Agent: Cisco-CUCM9.1
Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
CSeq: 102 INVITE
Max-Forwards: 70
Expires: 180
Allow-Events: presence
Supported: X-cisco-srtp-fallback
Supported: Geolocation
Contact: <sip:[email protected]:5060>
Content-Type: application/sdp
Content-Length: 244
v=0
o=CiscoSystemsCCM-SIP 9082578 2 IN IP4 10.18.81.11
s=SIP Call
c=IN IP4 0.0.0.0
b=TIAS:8000
b=AS:8
t=0 0
m=audio 21928 RTP/AVP 18 101
a=rtpmap:18 G729/8000
a=ptime:20
a=inactive
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
Nov 30 11:44:49.218: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720852ab8b92
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
CSeq: 102 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-15.2.4.M5
Content-Length: 0
Nov 30 11:44:49.218: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
INVITE sip:[email protected]:5060;transport=udp SIP/2.0
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC9241
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
Supported: 100rel,timer,resource-priority,replaces,sdp-anat
Min-SE: 1800
Cisco-Guid: 1020645888-0000065536-0000124117-0189862410
User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
CSeq: 102 INVITE
Max-Forwards: 70
Timestamp: 1417347889
Contact: <sip:[email protected]:5060>
Call-Info: <sip:10.18.81.2:5060>;method="NOTIFY;Event=telephone-event;Duration=2000"
Expires: 180
Allow-Events: telephone-event
Content-Type: application/sdp
Content-Length: 271
v=0
o=CiscoSystemsSIP-GW-UserAgent 7676 6959 IN IP4 10.18.81.2
s=SIP Call
c=IN IP4 0.0.0.0
t=0 0
m=audio 22256 RTP/AVP 18 101
c=IN IP4 0.0.0.0
a=inactive
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=yes
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=ptime:20
Nov 30 11:44:49.278: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3EC9241
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Call-ID: [email protected]
CSeq: 102 INVITE
Timestamp: 1417347889
Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
Supported:
Accept: application/media_control+xml,application/sdp,application/xml
Contact: <sip:[email protected]:5060;transport=udp>
X-BroadWorks-Correlation-Info: bbf94839-a234-4237-95e6-a7037322f0f4
Content-Type: application/sdp
Content-Length: 360
v=0
o=BroadWorks 316169737 2 IN IP4 10.111.111.254
s=-
c=IN IP4 0.0.0.0
t=0 0
m=audio 20074 RTP/AVP 18 101 100
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:100 X-NSE/8000
a=fmtp:100 200-202
a=X-sqn:0
a=X-cap: 1 audio RTP/AVP 100
a=X-cpar: a=rtpmap:100 X-NSE/8000
a=X-cpar: a=fmtp:100 200-202
a=X-cap: 2 image udptl t38
a=inactive
Nov 30 11:44:49.278: //64511/3CD5D2000001/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x0x3D7B1458
State of The Call : STATE_ACTIVE
TCP Sockets Used : NO
Calling Number : 27218091323
Called Number : 0862000000
Source IP Address (Sig ): 10.18.81.2
Destn SIP Req Addr:Port : 10.111.111.254:5060
Destn SIP Resp Addr:Port : 10.111.111.254:5060
Destination Name : 10.111.111.254
Nov 30 11:44:49.278: //64511/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : g729br8
Negotiated Codec Bytes : 20
Nego. Codec payload : 18 (tx), 18 (rx)
Negotiated Dtmf-relay : 6
Dtmf-relay Payload : 101 (tx), 101 (rx)
Source IP Address (Media): 10.18.81.2
Source IP Port (Media): 22256
Destn IP Address (Media): 0.0.0.0
Destn IP Port (Media): 20074
Orig Destn IP Address:Port (Media): [ - ]:0
Nov 30 11:44:49.282: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
ACK sip:[email protected]:5060;transport=udp SIP/2.0
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECA2633
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 102 ACK
Allow-Events: telephone-event
Content-Length: 0
Nov 30 11:44:49.282: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720852ab8b92
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
CSeq: 102 INVITE
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Contact: <sip:[email protected]:5060>
Supported: replaces
Supported: sdp-anat
Server: Cisco-SIPGateway/IOS-15.2.4.M5
Supported: timer
Content-Type: application/sdp
Content-Length: 271
v=0
o=CiscoSystemsSIP-GW-UserAgent 7965 2748 IN IP4 10.18.81.2
s=SIP Call
c=IN IP4 0.0.0.0
t=0 0
m=audio 22350 RTP/AVP 18 101
c=IN IP4 0.0.0.0
a=inactive
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=yes
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=ptime:20
Nov 30 11:44:49.282: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
ACK sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e72094953dfea
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 102 ACK
Allow-Events: presence
Content-Length: 0
Nov 30 11:44:49.290: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
INVITE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720a6918040f
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
Supported: timer,resource-priority,replaces
Min-SE: 1800
User-Agent: Cisco-CUCM9.1
Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
CSeq: 103 INVITE
Max-Forwards: 70
Expires: 180
Allow-Events: presence
Supported: X-cisco-srtp-fallback
Supported: Geolocation
Contact: <sip:[email protected]:5060>
Content-Length: 0
Nov 30 11:44:49.294: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720a6918040f
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
CSeq: 103 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-15.2.4.M5
Content-Length: 0
Nov 30 11:44:49.294: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
INVITE sip:[email protected]:5060;transport=udp SIP/2.0
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECB16F3
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
Supported: timer,resource-priority,replaces,sdp-anat
Min-SE: 1800
Cisco-Guid: 1020645888-0000065536-0000124117-0189862410
User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
CSeq: 103 INVITE
Max-Forwards: 70
Timestamp: 1417347889
Contact: <sip:[email protected]:5060>
Expires: 180
Allow-Events: telephone-event
Content-Length: 0
Nov 30 11:44:49.338: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECB16F3
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Call-ID: [email protected]
CSeq: 103 INVITE
Timestamp: 1417347889
Allow: ACK,BYE,CANCEL,INFO,INVITE,OPTIONS,PRACK,REFER,NOTIFY,UPDATE
Supported:
Accept: application/media_control+xml,application/sdp,application/xml
Contact: <sip:[email protected]:5060;transport=udp>
Content-Type: application/sdp
Content-Length: 306
v=0
o=BroadWorks 316169737 3 IN IP4 10.111.111.254
s=-
c=IN IP4 10.111.111.254
t=0 0
m=audio 20074 RTP/AVP 18 101
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=X-sqn:0
a=X-cap: 1 audio RTP/AVP 100
a=X-cpar: a=rtpmap:100 X-NSE/8000
a=X-cpar: a=fmtp:100 200-202
a=X-cap: 2 image udptl t38
Nov 30 11:44:49.342: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 2
PM-HO-VG-01#00 OK
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720a6918040f
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
CSeq: 103 INVITE
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Contact: <sip:[email protected]:5060>
Supported: replaces
Supported: sdp-anat
Server: Cisco-SIPGateway/IOS-15.2.4.M5
Supported: timer
Content-Type: application/sdp
Content-Length: 289
v=0
o=CiscoSystemsSIP-GW-UserAgent 7965 2749 IN IP4 10.18.81.2
s=SIP Call
c=IN IP4 10.18.81.2
t=0 0
m=audio 22350 RTP/AVP 18 101 19
c=IN IP4 10.18.81.2
a=rtpmap:18 G729/8000
a=fmtp:18 annexb=yes
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=rtpmap:19 CN/8000
a=ptime:20
Nov 30 11:44:49.350: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
ACK sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.18.81.11:5060;branch=z9hG4bK2e720b594cd517
From: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
To: <sip:[email protected]>;tag=3C365010-1E42
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
Max-Forwards: 70
CSeq: 103 ACK
Allow-Events: presence
Content-Type: application/sdp
Content-Length: 213
v=0
o=CiscoSystemsCCM-SIP 9082578 3 IN IP4 10.18.81.11
s=SIP Call
c=IN IP4 10.18.81.10
t=0 0
m=audio 4000 RTP/AVP 18
a=X-cisco-media:umoh
a=rtpmap:18 G729/8000
a=ptime:20
a=fmtp:18 annexb=no
a=sendonly
Nov 30 11:44:49.354: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
BYE sip:[email protected]:5060 SIP/2.0
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECC55
From: <sip:[email protected]>;tag=3C365010-1E42
To: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
Max-Forwards: 70
Timestamp: 1417347889
CSeq: 101 BYE
Reason: Q.850;cause=86
P-RTP-Stat: PS=874,OS=17480,PR=872,OR=17440,PL=0,JI=0,LA=0,DU=17
Content-Length: 0
Nov 30 11:44:49.354: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Sent:
BYE sip:[email protected]:5060;transport=udp SIP/2.0
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECD1ECD
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
User-Agent: Cisco-SIPGateway/IOS-15.2.4.M5
Max-Forwards: 70
Timestamp: 1417347889
CSeq: 104 BYE
Reason: Q.850;cause=65
P-RTP-Stat: PS=872,OS=17440,PR=952,OR=19040,PL=0,JI=0,LA=0,DU=17
Content-Length: 0
Nov 30 11:44:49.374: //64511/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 200 Race Condition
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECD1ECD
From: "Bianca Africa" <sip:[email protected]>;tag=3C364D44-9E2
To: <sip:[email protected]>;tag=71913148-1417348035284
Call-ID: [email protected]
Timestamp: 1417347889
CSeq: 104 BYE
Content-Length: 0
Nov 30 11:44:49.374: //64511/3CD5D2000001/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x0x3D7B1458
State of The Call : STATE_DEAD
TCP Sockets Used : NO
Calling Number : 27218091323
Called Number : 0862000000
Source IP Address (Sig ): 10.18.81.2
Destn SIP Req Addr:Port : 10.111.111.254:5060
Destn SIP Resp Addr:Port : 10.111.111.254:5060
Destination Name : 10.111.111.254
Nov 30 11:44:49.374: //64511/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : g729br8
Negotiated Codec Bytes : 20
Nego. Codec payload : 18 (tx), 18 (rx)
Negotiated Dtmf-relay : 6
Dtmf-relay Payload : 101 (tx), 101 (rx)
Source IP Address (Media): 10.18.81.2
Source IP Port (Media): 22256
Destn IP Address (Media): 10.111.111.254
Destn IP Port (Media): 20074
Orig Destn IP Address:Port (Media): [ - ]:0
Nov 30 11:44:49.374: //64511/3CD5D2000001/SIP/Call/sipSPICallInfo:
Disconnect Cause (CC) : 65
Disconnect Cause (SIP) : 200
Nov 30 11:44:49.406: //64510/3CD5D2000001/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 10.18.81.2:5060;branch=z9hG4bK3ECC55
From: <sip:[email protected]>;tag=3C365010-1E42
To: "Bianca Africa" <sip:[email protected]>;tag=9082578~cdf4c5a6-dd2b-4c71-bca0-b262ad997720-44517224
Date: Sun, 30 Nov 2014 11:44:49 GMT
Call-ID: [email protected]
CSeq: 101 BYE
Content-Length: 0
Nov 30 11:44:49.406: //64510/3CD5D2000001/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x0x3D816D70
State of The Call : STATE_DEAD
TCP Sockets Used : NO
Calling Number : 0218091323
Called Number : 0862000000
Source IP Address (Sig ): 10.18.81.2
Destn SIP Req Addr:Port : 10.18.81.11:5060
Destn SIP Resp Addr:Port : 10.18.81.11:5060
Destination Name : 10.18.81.11
Nov 30 11:44:49.406: //64510/3CD5D2000001/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : g729br8
Negotiated Codec Bytes : 20
Nego. Codec payload : 18 (tx), 18 (rx)
Negotiated Dtmf-relay : 6
Dtmf-relay Payload : 101 (tx), 101 (rx)
Source IP Address (Media): 10.18.81.2
Source IP Port (Media): 22350
Destn IP Address (Media): 0.0.0.0
Destn IP Port (Media): 21928
Orig Destn IP Address:Port (Media): [ - ]:0
Nov 30 11:44:49.406: //64510/3CD5D2000001/SIP/Call/sipSPICallInfo:
Disconnect Cause (CC) : 86
Disconnect Cause (SIP) : 200
PM-HO-VG-01#Hi Manish,
Again, excellent feedback. Much appreciated.
I will try the commands suggested above and see if I can get DTMF to work correctly while interworking H.323 and SIP.
But my ultimate goal is to have SIP all way from the CUCM to the CUBE and from the CUBE to the ITSP.
If I enable SIP Early Offer with MTP on the CUCM going to the CUBE, all SIP Invite sent from the CUCM to the CUBE uses G.729r8 as the codec and once the call is established using G.729r8 should the ITSP reply with that codec, the call succeed and I am able to see an active MTP session using G.729 when I issue the command # show sccp connections.
One thing that I saw is that my ITSP love so much sending G.729br8 most of the times, so even if using SIP EO with MTP on the SIP Trunk to the CUBE, when I sent my INVITE out from the CUCM to the CUBE using G.729r8, specially on call center numbers such as 0800 numbers, you will see that the call established but the codec being negotiated is G.729br8 which is voice only (missing DTMF).
I will be doing some intensive test again later on this week and will send the logs.
Here is my question to both of you:
Which is the best way of having a proper SIP to SIP setup all the way that will not pose any problem?
Do I have to enable Early Offer on the SIP Profile used by the CUBE SIP Trunk or should I use the normal Standard SIP Profile? Do I need to enable MTP on my CUBE SIP Trunk or not?
From the CUBE point of view, I have a voice class codec that support G.729r8 or G.729br8 and the DTMF Relay method supported by the ITSP is RFC 2833.
I will send more logs for each scenario. I think that we are getting close to the resolution of this problem.
Thanks again for your support fellows. -
ILBC calls via SIP Trunk with CUBE and CUCM7
hi there,
our SIP Provider offers the IBLC codec which promises to provide better quality compard to G.729.
I'm using this scenario:
IP-Phone(G711) --- CUCM7 --- (SIP-Trunk1) --- CUBE --- (SIP-Trunk2) --- Provider
Everything workes unless I'm configuring IBLC at the provider and on trunk2.
I have the CUBE router acting as a trancoding device and also specified IBLC as codec to be handled.
SIP trunk 2 was placed in a region with IBLC as codec.
On the trunk configuration in CUCM the media ressource group with XCODE capability is configured
Transcoding workes between two IP Phones in different regions with different codecs within the intranet.
Unfortunately the CUBE router doesn't seem to use the transcoder to change internal G711u calls into IBLC codec
so calls are blocked by the CUBE device:
deb ccsip calls
for incoming call:
.Mar 13 17:43:17.231: //145/BDB403DD8134/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x4AE7AC98
State of The Call : STATE_DEAD
TCP Sockets Used : NO
Calling Number : 0237892992
Called Number : 036677725231
Source IP Address (Sig ): 10.100.100.50
Destn SIP Req Addr:Port : <IP SIP Provicer>
Destn SIP Resp Addr:Port : <IP SIP Provicer>:5060
Destination Name : <IP SIP Provicer>
.Mar 13 17:43:17.231: //145/BDB403DD8134/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream : 1
Negotiated Codec : ilbc
Negotiated Codec Bytes : 0
Nego. Codec payload : 255 (tx), 255 (rx)
Negotiated Dtmf-relay : 6
Dtmf-relay Payload : 101 (tx), 101 (rx)
Source IP Address (Media): <IP CUBE>
Source IP Port (Media): 0
Destn IP Address (Media): <IP SIP Provicer>
Destn IP Port (Media): 22022
Orig Destn IP Address:Port (Media): [ - ]:0
.Mar 13 17:43:17.231: //145/BDB403DD8134/SIP/Call/sipSPICallInfo:
Disconnect Cause (CC) : 65
Disconnect Cause (SIP) : 488
(Output lookes similar to outgoing calls)
I set up ccm on cube and assigned dsp ressources without success:
Here are the relevant configuration parts:
voice class codec 1
codec preference 1 iblc
voice service voip
address-hiding
allow-connections sip to sip
allow-connections h323 to sip
allow-connections sip to h323
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
h323
sip
header-passing error-passthru
no update-callerid
midcall-signaling passthru
privacy-policy passthru
voice-card 0
dspfarm
dsp services dspfarm
dial-peer voice 40991 voip
description *** Incoming from SIP-Provider
destination-pattern 03667772523.%
session protocol sipv2
session target ipv4:<IP_of_CUCM>
voice-class codec 1
voice-class sip asserted-id pai
voice-class sip privacy-policy passthru
dtmf-relay rtp-nte
fax-relay sg3-to-g3
fax rate 14400
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
ip qos dscp cs5 media
ip qos dscp cs5 signaling
sccp local GigabitEthernet0/0
sccp ccm 10.100.100.50 identifier 11 version 4.1
sccp
sccp ccm group 11
description *** lokaler CCM fuer Codec-Konvertierung von SIP/DUS.NET
associate ccm 11 priority 1
associate profile 21 register DE_WGT_MTP02
dspfarm profile 21 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec ilbc
maximum sessions 10
associate application SCCP
telephony-service
sdspfarm units 1
sdspfarm transcode sessions 10
sdspfarm tag 1 DE_WGT_MTP02
max-ephones 30
max-dn 30
ip source-address 10.100.100.50 port 2000
max-conferences 8 gain -6
transfer-system full-consult
create cnf-files version-stamp 7960 Mar 14 2010 02:10:34
sh sccp
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
IPv4 Address: 10.100.100.50
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 10.100.100.50, Port Number: 2000
Priority: N/A, Version: 4.1, Identifier: 11
Trustpoint: N/A
Call Manager: 10.1.1.55, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 10
Trustpoint: N/A
Transcoding Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 10.100.100.50, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 21
Reported Max Streams: 20, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: ilbc, Maximum Packetization Period: 120
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
sh dspfarm dsp all
SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED
0 1 26.3.4 UP N/A FREE xcode 1 - - -
0 1 26.3.4 UP N/A FREE xcode 1 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
0 2 26.3.4 UP N/A FREE xcode 2 - - -
1 1 26.3.4 UP N/A FREE xcode 1 - - -
1 1 26.3.4 UP N/A FREE xcode 1 - - -
1 1 26.3.4 UP N/A FREE xcode 2 - - -
1 1 26.3.4 UP N/A FREE xcode 2 - - -
1 1 26.3.4 UP N/A FREE xcode 2 - - -
1 1 26.3.4 UP N/A FREE xcode 2 - - -
Thanks in advance,
DavidHi there,
Just wondering whether you ever got this resolved? I seem to have a very similiar problem.
Regards
Karen -
Creation of cube and dso in sap bi 7.0
This topic has ben discussed here often. Kindly search the forums before posting a new thread. Unfortunately I would have to lock this thread.
Hi
Can any body tell me the how to create the cube as well an dso in bi 7.0 version thougt i how to create cube and ods in sap bi 3.5 version but i want to update my knowledge more what are main diif b/w 3.5 and 7.0 i had ask this question further also but i will be very greate full if any give me own hand made Answer rather than the for diff b/w 3.5 and biw 7.0
regards
gurkiran
Edited by: Dinesh Lalchand on Feb 12, 2009 12:53 PM
Edited by: Dinesh Lalchand on Feb 12, 2009 12:55 PMHi ,
I am trying to migrate the Transaction data sources before moving into the DEV from Sandbox.
So i have to delete the existing TR/UR's and trying to create the transformation, but while creating transformation fields mapping is not happend automatically. (For manul field mapping the transaction data is the time taking process)
We are using the spk 8 . Please let me know any one has faced the above problem .
Regards
Jose -
Sip 503 service unavailable and sip 500 internal server error
Hi guys,could any one help me in the following.
ITSP-->Voice gateway configured as CUBE-->CUCM-->UCCX
I am moving a system from cme and aa enviroment to cucm and uccx
The VGW is configured as CUBE and also is added as h323 gateway on cucm.
When i tested the debug ccsip messages shows
Sip 503 service unavailable or
sip 500 internal server error.
I can't now provide any debugs cause i am not on site,only on Saturday.
As i read in previous discussion that could be the bind source address problem but i had this configured.
Also i tried to configure the gateway instead of h232 to use sip trunk from cucm,but after this the incoming calls didn't even reach the router,the debug ccsip messages showed nothing.
For now can any one advice me to what these 2 errors related to.
What could be missing?
Thanks in advance.Hi there : can some one explain the reason that i am getting this sip error with itsp:
here is the debug of ccsip messages:
Received:
INVITE sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/UDP 188.254.68.66:9298;branch=z9hG4bK-6110d60075a24c0f-a3c000c-1
Call-ID: isbc6994325518768294927-1385194135-11717
From: [email protected];user=phone>;tag=sbc09106994325518768294927
To:
CSeq: 1 INVITE
Min-SE: 90
Session-Expires: 3600;refresher=uac
Contact:
Allow: INVITE,CANCEL,BYE,ACK,REFER,UPDATE,INFO,PRACK
Supported: timer,100rel
Diversion: [email protected]>;privacy=off;screen=no;reason=unknown,[email protected]>;privacy=off;screen=no;reason=unknown
Max-Forwards: 70
User-Agent: VCS 5.8.2.56-03
Content-Length: 394
Content-Type: application/sdp
v=0
o=- 87852 198805 IN IP4 188.254.68.67
s=SBC call
c=IN IP4 188.254.68.67
t=0 0
m=audio 23682 RTP/AVP 8 0 18 98 96 97 101
a=rtpmap:98 G.729a/8000
a=rtpmap:96 G.729ab/8000
a=rtpmap:97 G.729b/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=fmtp:18 annexb=no
a=ptime:10
a=X-vrzcap:vbd Ver=1 Mode=FaxPr ModemRtpRed=0
a=X-vrzcap:identification bin=DSR2866 Prot=mgcp App=MG
00:43:23: //11/FDB448CE8020/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP 188.254.68.66:9298;branch=z9hG4bK-6110d60075a24c0f-a3c000c-1
From: [email protected];user=phone>;tag=sbc09106994325518768294927
To:
Date: Sat, 23 Nov 2013 08:06:29 GMT
Call-ID: isbc6994325518768294927-1385194135-11717
CSeq: 1 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-12.x
Content-Length: 0
00:43:23: //11/FDB448CE8020/SIP/Msg/ccsipDisplayMsg:
Sent:
SIP/2.0 503 Service Unavailable
Via: SIP/2.0/UDP 188.254.68.66:9298;branch=z9hG4bK-6110d60075a24c0f-a3c000c-1
From: [email protected];user=phone>;tag=sbc09106994325518768294927
To:
c2801#er=phone>;tag=27BA64-1DAE
Date: Sat, 23 Nov 2013 08:06:29 GMT
Call-ID: isbc6994325518768294927-1385194135-11717
CSeq: 1 INVITE
Allow-Events: telephone-event
Server: Cisco-SIPGateway/IOS-12.x
Reason: Q.850;cause=38
Content-Length: 0
00:43:23: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Received:
ACK sip:[email protected];user=phone SIP/2.0
Via: SIP/2.0/UDP 188.254.68.66:9298;branch=z9hG4bK-6110d60075a24c0f-a3c000c-1
Call-ID: isbc6994325518768294927-1385194135-11717
From: [email protected];user=phone>;tag=sbc09106994325518768294927
To: ;tag=27BA64-1DAE
CSeq: 1 ACK
Max-Forwards: 70
Content-Length: 0
show run:
voice service voip
ip address trusted list
ipv4 87.226.136.164 255.255.255.255
ipv4 172.16.24.0 255.255.255.0
ipv4 188.254.68.66 255.255.255.255
ipv4 188.254.68.67 255.255.255.255
ipv4 188.254.69.66 255.255.255.255
ipv4 188.254.69.67 255.255.255.255
ipv4 46.38.52.68 255.255.255.255
address-hiding
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
redirect ip2ip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback cisco
sip
voice class codec 1
codec preference 1 g729br8
codec preference 2 g729r8
codec preference 3 g711alaw
codec preference 4 g711ulaw
voice class codec 2
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
codec preference 4 g729br8
voice translation-rule 1
rule 1 /XXX5397962/ /1999/
voice translation-rule 2
rule 1 /XXX55317577/ /1999/
voice translation-rule 3
rule 1 /5555317884/ /1999/
voice translation-profile ROS
translate called 1
voice translation-profile ROS2
translate called 2
voice translation-profile ROS3
translate called 3
interface FastEthernet0/0
ip address 178.208.129.221 255.255.255.248
ip access-group INBOUND in
no ip unreachables
ip verify unicast reverse-path
ip nat outside
ip inspect IPFW in
ip inspect IPFW out
ip virtual-reassembly in
duplex auto
speed auto
no cdp enable
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1.1
encapsulation dot1Q 1 native
ip address 10.110.0.200 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.2
encapsulation dot1Q 2
ip address 172.16.24.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
h323-gateway voip interface
h323-gateway voip bind srcaddr 172.16.24.254
ip dns server
ip nat inside source list NAT interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 178.208.X.X
ip route 192.168.0.0 255.255.0.0 Null0 254
sccp local FastEthernet0/1.2
sccp ccm 172.16.24.101 identifier 1 version 7.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register XCODE123456
keepalive retries 1
keepalive timeout 10
switchover method immediate
switchback method immediate
dspfarm profile 1 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 6
associate application SCCP
dial-peer voice 10000 voip
tone ringback alert-no-PI
description ROSTELECOM Incoming
translation-profile incoming ROS
destination-pattern 74955397962
session protocol sipv2
session target ipv4:87.226.136.164
session transport udp
incoming called-number XXXX5397962
dtmf-relay rtp-nte
codec g711ulaw
dial-peer voice 10010 voip
tone ringback alert-no-PI
description ROSTELECOM Incoming
translation-profile incoming ROS2
destination-pattern XXX55317577
session protocol sipv2
session target ipv4:87.226.136.164
session transport udp
incoming called-number 75555317577
dtmf-relay rtp-nte
codec g711ulaw
dial-peer voice 10020 voip
tone ringback alert-no-PI
description ROSTELECOM Incoming
translation-profile incoming ROS3
preference 1
destination-pattern 5555317884
session protocol sipv2
session target ipv4:188.254.68.66
session transport udp
incoming called-number 5555317884
dtmf-relay rtp-nte
codec g711ulaw
dial-peer voice 10021 voip
tone ringback alert-no-PI
description ROSTELECOM Incoming
translation-profile incoming ROS
preference 2
destination-pattern 5555317884
session protocol sipv2
session target ipv4:188.254.69.66
session transport udp
incoming called-number 5555317884
dtmf-relay rtp-nte
codec g711ulaw
dial-peer voice 2 voip
tone ringback alert-no-PI
description to CUCM_PUB
destination-pattern 1...
session target ipv4:172.16.24.101
voice-class codec 2
dtmf-relay rtp-nte
I see in the debug that the itsp over g729 family codecs but not g711 at all
This system was working with this dialpeers before with same provider ,just i have added the dial-peer 2 .
I have changed the codec to match what is offered by itsp but no difference,still getting the same message.
PLZ help ASAP. -
Migrate cognos cubes to essbase
Hi,
Does anyone know the steps to migrate Cognos cubes to Essbase 11? I've no idea where to start from other than doing it manually from scratch, like building the outline & loading data.
Can we export metadata & data from Cognos in a format which can be loaded to Essbase w/o much tedious manual task?
Any suggestions?
ThanksHi Srinivas,
Thank you for quick reply.
could you explain me process little bit clearly.
can you explain how to extract the data from cognos cubes to the relational layer?are there any third party tools for doing the same?
How do you compute complex calculation in cognos.can we do scripting in cognos as we do it is essbase using calculation scripts.
for eg :do you incorparate if else st in cognos(thinking in terms of reusability).
How can a security be migrated from cognos to essbase.
Have you used any third party tools for migration.
What is "report matrix " I don't have idea about cognos.
and some more things you followed
Thanks! -
Migrating Essbase cube across versions via file system
A large BSO cube has been taking much longer to complete a 'calc all' in Essbase 11.1.2.2 than on Essbase 9.3.1 despite all Essbase.cfg, app and db settings being same (https://forums.oracle.com/thread/2599658).
As a last resort, I've tried the following-
1. Calc the cube on the 9.3.1 server.
2. Use EAS Migration Wizard to migrate the cube from the 9.3.1 server to the 11.1.2.2 server.
3. File system transfer of all ess*.ind and ess*.pag from 9.3.1\app\db folder to 11.1.2.2\app\db folder (at this point a retrieval from the 11.1.2.2 server does not yet return any data).
4. File system transfer of the dbname.esm file from 9.3.1\app\db folder to 11.1.2.2\app\db folder (at this point a retrieval from the 11.1.2.2 server returns an "unable to load database dbname" error and an "Invalid transaction status for block -- Please use the IBH Locate/Fix utilities to find/fix the problem" error).
5. File system transfer of the dbname.tct file from 9.3.1\app\db folder to 11.1.2.2\app\db folder (and voila! Essbase returns data from the 11.1.2.2 server and numbers match with the 9.3.1 sever).
This almost seems too good to be true. Can anyone think of any dangers of migrating apps this way? Has nothing changed in file formats between Essbase 9.x and 11.x? Won't not transferring the dbname.ind and dbname.db files cause any issues down the road? Thankfully we are soon moving to ASO for this large BSO cube, so this isn't a long term worry.Freshly install the Essbase 11.1.2.2 on Window server 2008 r-2 with the recommended hardware specification. After Installation configure 11.1.2.2 with the DB/Schema
Take the all data back up of the essbase applications using script export or directly exporting from the cube.
Use the EAS Migration wizard to migrate the essbase applications
After the Migrating the applications successfully,reLoad all the data into cube.
For the 4th Point
IBH error generally caused when there is a mismatch in the index file and the PAG file while e executing the calculation script .Possible solutions are available
The recommended procedure is:
a)Disable all logins.
alter application sample disable connects;
b)Forcibly log off all users.
alter system logout session on database sample.basic;
c)Run the MaxL statement to get invalid block header information.
alter database sample.basic validate data to local logfile 'invalid_blocks';
d)Repair invalid block headers
alter database sample.basic repair invalid_block_headers;
Thanks,
Sreekumar Hariharan -
CCM v5.0 with ip phones running SCCP and SIP
Planning to migrate to CCM v5.0. Just would like to confirm CCM v5.0 can support to run SCCP and SIP phones simultaneously without any major issues. Does anyone has any experenice to setup this environment? Currently we are running 7960G and 7912G. Thanks.
Yes, it works. 100% guaranteed!
Linksys, Sipura, Grandstream IP phones work pretty fine with Cisco CCM 5 -
Can't view my Cube and Dimension Data with the Cube Viewer
I'm new in using OWB, i'm using Oracle 10g release1 with OWB R2 also Oracle WorkFlow 2.6.3.
When studying with the steps from the OTN pages (start01, flat-file02, relational-wh-03, etl-mappings, deployingobjects, loading-warehouse and bi-modeling)
the loading was success, i guess...
But when I want to see the data in the cube and dimension, an error occurs.
It says
" CubeDV_OLAPSchemaConnectionException_ENT_06952??
CubeDV_OLAPSchemaConnectionException_ENT_06952??
at oracle.wh.ui.owbcommon.dataviewer.dimensional.DataViewerConnection.connect(DataViewerConnection.java:115)
at oracle.wh.ui.owbcommon.dataviewer.dimensional.DimDataViewerMain.BIBeansConnect(DimDataViewerMain.java:433)
at oracle.wh.ui.owbcommon.dataviewer.dimensional.DimDataViewerMain.init(DimDataViewerMain.java:202)
at oracle.wh.ui.owbcommon.dataviewer.dimensional.DimDataViewerEditor._init(DimDataViewerEditor.java:68)
at oracle.wh.ui.editor.Editor.init(Editor.java:1115)
at oracle.wh.ui.editor.Editor.showEditor(Editor.java:1431)
at oracle.wh.ui.owbcommon.IdeUtils._tryLaunchEditorByClass(IdeUtils.java:1431)
at oracle.wh.ui.owbcommon.IdeUtils._doLaunchEditor(IdeUtils.java:1344)
at oracle.wh.ui.owbcommon.IdeUtils._doLaunchEditor(IdeUtils.java:1362)
at oracle.wh.ui.owbcommon.IdeUtils.showDataViewer(IdeUtils.java:864)
at oracle.wh.ui.owbcommon.IdeUtils.showDataViewer(IdeUtils.java:851)
at oracle.wh.ui.console.commands.DataViewerCmd.performAction(DataViewerCmd.java:19)
at oracle.wh.ui.console.commands.TreeMenuHandler$1.run(TreeMenuHandler.java:188)
at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:178)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:454)
at java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.java:201)
at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:151)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:145)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:137)
at java.awt.EventDispatchThread.run(EventDispatchThread.java:100) "
Can somebody explain what is happening, I really don't understand, when the cube viewer window appears, there's no data in it....
I realy need help with this...I'm new in using OWB, i'm using Oracle 10g release1 with OWB R2 also Oracle WorkFlow 2.6.3.
When studying with the steps from the OTN pages (start01, flat-file02, relational-wh-03, etl-mappings, deployingobjects, loading-warehouse and bi-modeling)
the loading was success, i guess...
But when I want to see the data in the cube and dimension, an error occurs.
It says
" CubeDV_OLAPSchemaConnectionException_ENT_06952??
CubeDV_OLAPSchemaConnectionException_ENT_06952??
at oracle.wh.ui.owbcommon.dataviewer.dimensional.DataViewerConnection.connect(DataViewerConnection.java:115)
at oracle.wh.ui.owbcommon.dataviewer.dimensional.DimDataViewerMain.BIBeansConnect(DimDataViewerMain.java:433)
at oracle.wh.ui.owbcommon.dataviewer.dimensional.DimDataViewerMain.init(DimDataViewerMain.java:202)
at oracle.wh.ui.owbcommon.dataviewer.dimensional.DimDataViewerEditor._init(DimDataViewerEditor.java:68)
at oracle.wh.ui.editor.Editor.init(Editor.java:1115)
at oracle.wh.ui.editor.Editor.showEditor(Editor.java:1431)
at oracle.wh.ui.owbcommon.IdeUtils._tryLaunchEditorByClass(IdeUtils.java:1431)
at oracle.wh.ui.owbcommon.IdeUtils._doLaunchEditor(IdeUtils.java:1344)
at oracle.wh.ui.owbcommon.IdeUtils._doLaunchEditor(IdeUtils.java:1362)
at oracle.wh.ui.owbcommon.IdeUtils.showDataViewer(IdeUtils.java:864)
at oracle.wh.ui.owbcommon.IdeUtils.showDataViewer(IdeUtils.java:851)
at oracle.wh.ui.console.commands.DataViewerCmd.performAction(DataViewerCmd.java:19)
at oracle.wh.ui.console.commands.TreeMenuHandler$1.run(TreeMenuHandler.java:188)
at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:178)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:454)
at java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.java:201)
at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:151)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:145)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:137)
at java.awt.EventDispatchThread.run(EventDispatchThread.java:100) "
Can somebody explain what is happening, I really don't understand, when the cube viewer window appears, there's no data in it....
I realy need help with this... -
What is the diff b/w transactional cube and std cube
What is the diff b/w transactional cube and std cube
Hi Main differences,
1) Trasactional infocube are optimized for writing data that is multiple user can simultaneously write data into it without much effect on the performance where as the std infocube are optimized to read the data ie.e through queries.
2) transactional inofcubes can be loaded through SEM process as well normal laoding process.Std can be loaded only thorugh normal loading process.
3) the way data is stored is same but the indexing and partionong aspects are different since one is optimized for writing and another one for reading.
Thanks
Message was edited by:
Ajeet Singh -
Doughts on Infoset Joins with Cube and DSO in BI 7
Dear All,
I have a droughts on Infoset Joints.
I am working on a BI Query where I need to take 0Employee from Cube and Employee position time he holds in an Organization is coming form DSO, Apart for this I also have other requirement such as Address fields , Visa Status , are all coming from DSO.
I have created a Infoset for this where
1st is Cube and its 0Employee is linked to all DSO Employee and also Employee position I have linked with DSO and all are inner joints.
1>My doughty is that will this work with inner joins or I have to use other joints.
2>Is sequence of Data Target is correct
which is
1> Cube and in 2> all DSO in Parallel.
Please guide me on joints and sequence.
Thanks V V much in Advance,
Regards,Hi,
Check these links.
http://help.sap.com/saphelp_nw04s/helpdata/en/ed/084e3ce0f9fe3fe10000000a114084/frameset.htm
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/2f5aa43f-0c01-0010-a990-9641d3d4eef7
http://help.sap.com/saphelp_nw04/helpdata/en/9c/6b7538c9a8ee45e10000009b38f8cf/frameset.htm
if this helpa assign points.
Thanks.....
Vasu..... -
BI 7.0 can we build a INFOSET on a Multi Cube and Infoobject
Hi
In BI 7.0 can we build a INFOSET on a Multi Cube and Infoobject
ThanksHi,
No not possible.
You can include any DataStore object, InfoCube or InfoObject of type Characteristic with Master Data in a join. A join can contain objects of the same object type, or objects of different object types. You can include individual objects in a join as many times as you want. Join conditions (equal join condition) connect the objects in a join to one another . A join condition specifies the combination of individual object records included in the results set.
For more info go through the link below
http://help.sap.com/saphelp_nw2004s/helpdata/EN/ed/084e3ce0f9fe3fe10000000a114084/content.htm
Regards,
Marasa. -
Hi,
Generally reporting will be done on Info Cube rather than DSO.
Suppose If we assign the same data source to Info Cube and DSO then both contains the same data.
Info cube have additive and aggregated functionality where DSO have the overwrite functionality .
Are we using cube for this functionality only ?
What about the Dimensions in Cube how they differ from data fields and key fields in DSO when we are developing same Bex Report on both ?
Please advice me .
Thanks in advance.
Thanks & Regards,
Ramnaresh.pIt is hard to compare Cube and DSO.
Both thier own usage.
1. InfoCube is always additive, while DSO supports overwrite functionality.
2. In InfoCube, combination of all the characteristic value is a Key in the Fact Table, while in ODS, you can specify your own Key Fields based on which you want to generate unique record in the DSO.
3. DSO supports many delta modes like D, R, N, X, after image, before image, while cube does not support all the modes. You can not delete the record based on the key from the cube by just loading the data. While DSO automaitcally deletes the record from active table and generates the reverse entry for Cube.
4. DSO is a flat structure and therefore, it is used to store information at detail level, while cube is used to store information at aggregated level.
So both the structures are very much different from each other. One can replace other at some places, but both the objects have thier own functionality.
- Danny -
CME 7.1 with SCCP 7940G phones and SIP connection to a VOIP provider - inbound outbound fails
Here's a quick and dirty diagram of a CME 7.1 configuration. The phone can all call each other but something is not quite right with the SIP provider. The registrar and SIP registration pieces are working but most of the configuration examples that I've seen make me think that the CME router was being used as the edge device to the internet. From my drawing, you can see that is not the case here. My edge device is a Cisco ASA5505 with 9.2.x software running. I might be missing something in the SIP gateway knowledge department. Without diving into the configuration, I'm wondering if SIP messages are failing for calls because of NAT'ing? Trying to do searches has been tricky because I keep running into information that is more about setting up CME for SIP phones or just getting SIP to work between CME and a SIP provider. I have that part working. I'm just a bit unsure about how an SCCP 7940G gets an outbound call or even gets one to come in.
When I dial from my cell phone to the pilot number, there are no rings, it just goes to the VOIP provider's voice mail. When I try to dial out, I get a fast busy.
So, is NAT a consideration? Will the SIP gateway set up a call (forward) via the pre-established SIP connection? Yeah, I do sound like a newb.
If anyone has good information about, let's say, an inbound call and how that traffic flow works.
Thanks!Have you configured your ASA to either NAT the IP address of the CME router or to do port forwarding for port 5060?
Maybe you are looking for
-
I get a memory stacking kernel panic when I startup Mac osx
Can only boot into safe mode... When booted normally a black and white screen comes up with the aPple logo and a bunch of kernel code errors. I saw a pic online of someone else getting the same error message and the problem was referred to as a memor
-
Bank details of the Vendor are not picked up from Vendor Master in APP Run
Hai SAP Gurus, When the Automatic Payment Programme(F110) was run it is not giving bank details of the vendor in the payment file. These details are sent to bank in the file form. It should give account holder name in the payment file where as it is
-
Table of Contents Issue for ePub
I am trying to create a TOC for an ePub that looks like I want it to: Chapter One: The Name of Chapter One Chapter Two: The Name of Chapter Two etc. To do this: I imported the ePub styles from the ePub sample document On a page which begins a chapter
-
Hi All Does anyone know if KM is to be bandled with new release Hypeiron 11.1.1.0.0 and the timing? Thank you in advance. Regards, Yumi
-
Firefox Icon does not appear in the top left corner of the Browser on a Mac Desktop
I have an Intel iMac with OSX version 10.6.7. I downloaded Firefox 4.0 and do not have the Firefox icon in the upper left hand corner of the browser. It appears on my Windows 7 machine but not my Mac.