Mini DVi to DVI D

Which is the best route to go from my MacBook to my LCD TV (DVI D)
I bought a mini Dvi to VGA Adaptor from Apple as I thought the TV was VGA (the Ebay ad said so anyway) but it turns out its a Dvi D.
Is there a way to use my MiniDVi-VGA Adaptor or will I need a new one? What about the extension cable?
Cheers!

Why not return that mini-DVI to VGA adapter and get the mini-DVI to DVI adapter?

Similar Messages

  • 27: iMac Apple Mini DisplayPort to DVI adapter quits working post-firmware

    I iMac Apple Mini DisplayPort to DVI adapter suddenly quit working after I installed Apple's latest iMac display firmware update. This is an Intel Core i5; the monitor is an LG Flatron 24" Wide, and when it powers up it says "no video input" and goes into power-saving mode. No amount of replugging cables helps, but the monitor works fine on other computers.
    The Displays control panel just shows one monitor, and clicking Detect Displays does nothing.
    I suspect Apple's Display Firmware Update. My installer log shows the following, but the problem only happened today after the latest update:
    6/1/10 9:45 AM 27-inch iMac EFI Firmware Update 1.0
    6/1/10 9:45 AM 27-inch iMac Display Update 1.0
    6/4/10 11:47 AM 27-inch iMac SMC Firmware Update 1.0
    6/4/10 11:47 AM 27-inch iMac Display Update 1.0
    6/5/10 7:29 AM 27-inch iMac Display Update 1.0
    I have automatic updates disabled, but after each update I would see more firmware updates ready, but caution leads me to never install more than one of these at a time, and then to wait a while to see if anything bad happens. The odd thing is that the Display Update 1.0 seems to have been installed three times in this course of events. Alas, there appears to be no way to uninstall a firmware update.
    Here is the System Profiler Graphics/Displays output:
    Chipset Model: ATI Radeon HD 4850
    Type: GPU
    Bus: PCIe
    PCIe Lane Width: x16
    VRAM (Total): 512 MB
    Vendor: ATI (0x1002)
    Device ID: 0x944a
    Revision ID: 0x0000
    ROM Revision: 113-B9110C-425
    EFI Driver Version: 01.00.383
    Displays:
    iMac:
    Resolution: 2560 x 1440
    Pixel Depth: 32-Bit Color (ARGB8888)
    Main Display: Yes
    Mirror: Off
    Online: Yes
    Built-In: Yes
    Connection Type: DisplayPort
    Display Connector:
    Status: No Display Connected
    It says the Mac sees no display connected, and the display gets no video signal. Since the adapter is an active device (it has powered electronics to convert DisplayPort signals to DVI signals) I suppose it could have just coincidentally died. But that seems unlikely given that the thing worked perfectly just before the last firmware update.
    Does anybody have similar experience, or better yet, a fix?

    Unfortunately the Apple Knowledge Base does not give much information about this update. Such has how to tell if it has been successfully installed. I suspect that because it keeps recurring in the install log that it has not been installed successfully as yet. Are you receiving this update through Software Update? Can you locate the installer for this update? It maybe located in Apps/Utilities.
    Some firmware update installations can be interrupted/corrupted by attached devices. If you find the update's installer on your iMac, I suggest that you detach all external devices from the iMac, use an Apple USB keyboard & mouse if available, follow the instructions carefully and install the update manually. If you do not locate the installer I suggest downloading manually from the link below and installing it.
    The Knowledge Base article mentions that your iMac should also have a Graphics Firmware Update. I suggest that you download and install that as well.
    27-inch iMac Display Firmware Update 1.0
    http://support.apple.com/kb/DL998
    27-inch iMac Graphics Firmware Update 1.0
    http://support.apple.com/kb/DL984
    Dah•veed

  • Why Apple Mini-DVI to DVI Adapter couldn't be connected?

    i purchased Apple Mini-DVI To DVI adapter but it couldn't be connected to any port of my macbookpro 13" without retina
    if you 've solution please advise.

    What is the model identifier of your MBP? Also what oSX are you using?
    You can find this info by clicking on the Apple in the menu bar About this Mac, in the first window it should should show the OSX Version.
    Then click on More info, and the next page (Hardware overview) second line should be Model Identifier: x,x
    What are you connecting to and what type of input(s) does it have. If you do not know how to idendify the inputs, post the make, model of the device. 

  • Apple Mini-DVI to DVI Adapter

    Ok I have this adaptor and the RCA out one to. My question is do they sell a extension to connect to the Mini-DVI end that will make it longer so I can connect my 20in Cinema Display to my 20in Intel IMAC I can do it now, but this is the way I have it set up now, I have a shelve with the PC up on top off to my Right and the Cinema Display is also on the Right side of my L Shaped Desk and If I want to hook my Display up to the IMAC which is off to the Left I have to Disconect it from the PC up top then bring down the cord all the way over to the IMAC and then Unplug the Display its a very big Task to do. I would just like to get either a DVI extension to plug into the Display or a Extension for the MINI-DVI part to connect to the Apple Mini-DVI to DVI Adapter to make that longer so I can reach it up to the Top shelve so I can just swap them when I want to. If anyone knows if they sell that. That would be cool, I have not been able to find anything yet.

    I actually think I found what I need now. Found a Male To Female 3 foot Exetension, So Thanks to anyone Who was going to Answer to this or was thinking about it

  • Mini-DVI to HDMI adapter or Mini-DVI to DVI cable?

    I know Apple has a couple different Mini-DVI adapters for their Powerbook and MacBook computers. I don't especially like adapters and was wondering if anyone knows of a Mini-DVI to DVI cable.
    Also, with the gaining popularity of HDMI, do you think we will ever see a Mini-DVI to HDMI adapter or cable?

    Hi,
    I know it is changing the subject, but I've been long frustrated by Apple's penchant for odd connectors, especially video connectors. Remember old quadras with 13 pin D connectors, powerbooks with square connectors, 7100s with I-don't-know-what connectors? All the while, ye olde VGA 15-pin D-sub connector was on just about everything else - even gas chromatographs.
    We also got that funny mini-dix (Digital-Intel-Xerox) Ethernet connector on powerbooks when PCs were outfitted with familiar RJ-45 jacks. I did see one other machine that had the mini-dix: a government spec Zenith notebook.
    I'm surprised Apple didn't use a VGA connector on the Macbook, given its above average exposure in the educational environment and greater than average odds of being hooked up to a lectern in a distance learning room. Pretty much to a tee, every distance learning setup I've seen has a VGA cable at the presenter's lectern. I worked in a university IT department, and it was pretty common for our loaner laptops to come back missing just about any ancillary goodie that could be misplaced. It isn't so bad to have to routinely stuff a new $2.00 cat-5 cable in the bag, but a $20.00 video dongle - not so good!
    If Apple just couldn't countenance the idea of a VGA connector, I wonder how hard it would have been to have a normal size DVI connector? At least DVI-to-VGA connectors are easier to find, and better, aren't so expensive.
    Bill
    Message was edited by: impulse_telecom

  • Mini- DVI to VGA adapter Or is that, DVI to DVI?

    I am having difficulty figuring out which adapter to purchase if I want to use my MacBook to make a Keynote or PowerPoint Presentation with an LCD projector.
    Do I need the Mini- DVI to VGA adapter, or is it DVI to Video adapter, or DVI to DVI adapter? Good grief! I've made fabulous-looking slides and just want to take my computer to the lecture hall, connect it to their projector, and give my talk. How does one decide which cable to get, if I don't know for certain what kind of projector they are using?
    Aren't all LCD projectors standardized this way?
    Thanks for the clarification.
    ~ john

    As mentioned, VGA is much more common than DVI is on projectors, so the mini-DVI to VGA will certainly work more often than the mini-DVI to DVI will.
    It costs $19USD, so I would get both and use the best option available to you when you get to the location and see what kind of projector they have.
    You also may want to pack the VGA and a DVI cable just in case. You never know if the location will have one on hand, or if it gets misplaced just in time for your arrival.

  • Apple Mini DVI to DVI Adapter to connect Win7 tower to iMac / Target Display Mode

    I currently run Windows on bootcamp on the iMac (Mid-2011), although the tasks I perform (3D modelling, rendering and such) cause the Mac to get very hot, and as a result hae a slight burn mark on the LED LCD screen.
    I am buying a Windows machine, and am to uninstall bootcamp and use the Mac purely for OSX, but use the iMac screen as a monitor for the tower using Target Display Mode. My issue is - the Windows 7 tower only has DVI output. And as I understand, the Mid-2011 iMac only supports Target Display Mode via a thunderbolt cable.
    My question is - Will the Apple Mini DVI to DVI adapter allow me to connect the DVI-only tower to the iMac? Thanks in advance x

    Oh, I should mention also that the iMac is the 27" model. Mid-2011 3.4Ghz Intel Core i7 with 4GB RAM and 1TB Harddrive. And ATI HD5450 1GB Graphics.

  • Apple Mini DVI to DVI Adapter - Too short?

    I want to connect my iMac 2.8 ghz, 24" screen to an external Philips 190B LCD monitor and use the Extended Desktop function.
    The Philips Monitor model is the 190B6CG/00 and it is a single link monitor (Philips tell me it is DVI-D Receptacle Connector 24 pin = single link).
    I'm looking at the Apple Mini DVI to DVI adapter here on the Apple Store. It looks like it should plug into my iMac one end then the other end into my Philips. However it looks like it is too short to reach my Philips Monitor. They are not a fantastic distance apart. In fact they are sat side by side - but I somehow can't see the Apple Adapter being long enough (unless it crosses a 3-sphere).
    Presumably then, some sort of extension is required between the DVI end of the Apple adapter and the Philips Monitor's DVI input.
    Does anyone know what this extension could be and where is may be purchased?
    Regards

    Hello to everyone who has replied to my cry for help.
    Thank you all. I will apply points to everyone who has responded (so quickly too).
    Scorpie
    I totally agree. I have been thinking along these lines too. However, searching on the internet whilst researching, I found it difficult to decide what I needed because of the 'photos' supplied. They were ok as such but most didn't show very well the pin outs. Further research into the matter (and one website in particular - i.e. Maplin) made me realise that GENDER was involved. Also, with DVI, females look like males in web photos until you find a photo from the right angle. Same goes for VGA I reckon.
    I'm certain most people looking at DVI (and VGA) cable/connectors can't tell the difference when the devices are only viewed from 'above' . In my opinion they need to be viewed more or less end-on to show where they have pins or holes. I mean full end-on, not at an angle where (as I found above) detail as to pin or hole is lost in digital or compression noise. This is what I have experienced in all but one of the web sites I have visited. Another thing, most websites have an 'enlarged version' button which, if selected, shows the same photo exactly the same size. No help whatsoever. But then there's no doubt you must already be well aware of this.
    MyHighway
    You are correct. The Philips did come with a VGA cable. However I want to connect to my iMac digitally (if I can) using DVI (it looks like a 'female' connector on inspection of the back of the Monitor). I have found it almost impossible to tell the difference from most photos on the web even with my new huge screen iMac. One of the reasons I'm am a little nonplussed I think.
    mrtotes
    Good point. If I take a photo of the back of my Philips and take the Apple connector down to Maplin perhaps I can compare and contrast with real specimens. Yo!!
    I think I will give that a go.
    You have all been very helpful indeed. Opened my eyes somewhat.
    I wish a Merry Christmas to all my new Mac friends

  • Apple Mini DVI to DVI Adapter - Gender Question

    The Apple Mini DVI to DVI Adapter photograph in the Apple Store looks like the DVI end is female.
    Is this correct?
    The Overview photo is good because it made me aware that I needed more than just the adapter itself to use it, but I think it would help if an "end-on" view could also accompany the view of this product - just for old fogeys like me.
    I'm sure that some sort of industry 'convention' must exist so that I could use to determine this for myself. Be jiggered if I could find one though.

    Yes, the end is female. That makes it the same as if the connector were built-in. For example, the connector on the MacBook Pro is a female DVI. So you would need the same, and very common, DVI male-to-male connector to hook up a monitor. You don't need any extra adapters. Just the cable. Or if you have an Apple Cinema Display, the correct cable is already attached to the monitor.

  • Does Thunderbolt work with the Mini Displayport to DVI adapter?

    I just ordered a new 13" MacBook Pro with Retina Display to replace my Mid-2010 15" MacBook Pro.  I've been using the Mini Displayport to DVI adapter to extend my screen to an older 20" Cinema Display.  From what I can find online, and I'm here asking for confirmation, I should still be able to use the Mini Displayport to DVI adapter with the new MacBook Pro's Thunderbolt port.  Correct? 

    still be able to use the Mini Displayport to DVI adapter with the new MacBook Pro's Thunderbolt port.  Correct?
    Yes.

  • HT3153 Can the early 2006 MAC mini support a DVI to hdmi adapter for TV monitor support?

    Can the early 2006 MAC Mini support a DVI to HDMI adapter for a TV Monitor?

    Hi, I can't see why not...
    Supports digital resolutions up to 1920x1200 and analog resolutions as high as 1920x1080.
    http://www.everymac.com/systems/apple/mac_mini/specs/mac_mini_cd_1.66.html

  • Apple DVI to Video adapter + Mini DVI to DVI adapter pins not same

    I just purchased an Apple DVI to Video adaptor so I could plug in a Mac mini to an older tv, however the pin arrangement on the Apple DVI to Video adapter is not the same as the pin arrangement on the Mini DVI to DVI adapter that came with the Mac mini.
    Anyone have any idea what adapter I can use to make this connection?

    Joseph Kriz wrote:
    James,
    I'm confused here.
    Which Mini do you have?
    I know you posted this in the 2009 Mac Mini section so your Mini should have 2 video out ports.
    1. Mini DVI
    2. Mini DisplayPort
    If that is true, then there is no way you could have connected the DVI to Video adapter in your first post as the new Mini does not have a DVI port.
    The new Mini's come with 1 adapter.
    Mini DVI to DVI adapter.
    I don't know of any Apple adapters that will output to S Video, component or composite connections on the new Mini's.
    The one that osxdude shows above will not work on a new Mini. It say nothing about a Mini in their description:
    *The Mini-DVI to Video adapter is designed for the iMac (Intel Core Duo), MacBook*, and 12-inch PowerBook G4, allowing you to connect to most S-video or Composite enabled devices.*
    Good Luck and let us know what you find.
    Yes, I have a late 2009 Mac mini. It came with the mini DVI to DVI adapter as you stated. I need to hook up to an older tv with yellow component video port. Not knowing any better, and looking online, it looked like the male DVI end of the “Apple DVI to video” adapter would connect to the female DVI end of the “Mini DVI to DVI” adapter that came with the Mac mini. I figured that since they were both DVI plugs, male and female, they would connect, but the “Apple DVI to video” adapter has 4 extra pins, so they won’t.
    Then, following osxdude’s lead, I went to a local independent Apple store, and they told me that the same adapter that osxdude suggested would work, so I bought that (at an inflated price), but as you stated, it does not work. Also, as you stated, the Apple site does not list the Mac mini as being used with this adapter, which is why I did not originally purchase it online. It was only at the insistence of the independent Apple store that it would work that I purchased it. Unfortunately, once the package is opened
    the store were I purchased it will not take it back. Boy... this is getting expensive, and confusing! Why so many adapters?
    After much searching I found this info: http://forums.macrumors.com/showthread.php?t=706736&highlight=monoprice so I’m going to try that.
    Once it’s all said and done, I guess I’ll be listing a few adapters on ebay!

  • Macbook not recognizing mini dvi to dvi adapter

    Hi,
    I have a 2011 macbook pro, i have been using the mini dvi to dvi adapter to connect to a dvi to hdmi cable into my tv. It has worked for the past 6 months since i have owned my mac but just recently nothing happens when i plug the adapter into my mac. My friend has the same setup and nothing happened either when i plugged his into my mac so im thinking it is something to do with the computer thunderbolt port? any suggestions? thanks.

    Here is an Apple article on the subject of having no video on an external monitor. It's written about the Mac mini, but it applies equally to any other Mac.
    http://docs.info.apple.com/article.html?artnum=301345
    And here is another Apple article that is more generalized and with fewer suggestions, though it might be a good place to start from. Good luck.
    http://support.apple.com/kb/HT1573

  • Mini-DVI to DVI, DVI to VGA and No video on Samsung SyncMaster LCD

    External monitor works fine on a PC with same adapter (minus the Mini-DVI to DVI). OSX recognizes the external monitor and even gives display options in system preferences, and the mouse moves off the main display into the extended display but external LCD sits in sleep mode, but must detect some sort of video signal because when i pull the cable i get the "No Video Detected" warning on the external monitor. Could OSX be sending a sleep signal to the external display? I checked all the Energy Saver prefs? Any other thoughts?
    Late 2006 20" iMac
    OSX 10.5
    250 GB HD
    1 GB Ram

    Malcolm Rayfield wrote:
    The mini-DVI to DVI adapter may not be passing the analog video needed for VGA.
    Apple's mini-DVI to DVI adapter DOES NOT pass analog VGA signals.
    For some inexplicable reason, Apple chose to use a digital-only DVI-D
    connector. The analog video signals (pins C1 thru C4 in the drawing
    below) are not connected.
    http://en.wikipedia.org/wiki/DVI
    The DDC channel and 'hot plug detect' signals are connected, so
    the IMac and monitor can "see" each other -- but there's no path
    for the analog video.
    ...nuthin' in TheRuleBook sez it has to make sense,
    Looby

  • Monitor won't work via mini-dvi to dvi adapter

    It's a brand spanking new mac mini. I attached a 5 year old lcd monitor (always used before as VGA) using the mini-dvi to dvi adapter. I am using the monitor's dvi connector. The monitor resolution is 1280x1024.
    The monitor does not work when using the mini-dvi to dvi adapter. If I remove the mini-dvi adapter and use a mini displayport to dvi adapter, it works just fine. I can keep both adapters plugged in and plug the cable into one or the other. It always works instantly when attached to the minidisplay port and doesn't work if I switch to the mini-dvi port.
    I've tried the display with mini-dvi adapter on my macbook too. On the laptop, it acts like there are two screens attached, but there is no action on the external display.
    As a further test, I attached the mac mini to the TV via a mini-dvi to hdmi adapter. The mini-dvi port on the mini works fine, as does the port on the laptop. The monitor works fine via minidisplay, but not mini-dvi.
    Naturally, I concluded that the mini-dvi adapter was faulty. A second adapter came today, and nothing has changed. Could I have received two Apple mini-dvi adapters in a row with problems? Is there something about the monitor that doesn't like the mini-dvi port? It seems like it wouldn't like the minidisplay port either, but that one is fine.

    • Went to Best Buy
    • Paid for a DYNEX Mini DisplayPort to HDMI Adapter ($25)
    • Came home and plugged in the adapter then the HDMI to DVI cable to the monitor. (Note: Monitor is a LG Flatron L22WTG) - DID NOT WORK
    • iMac knows monitor is plugged in and I can change the resolution on both monitors and mirror. (Note: Changed to every resolutions with/without mirror image.) - DID NOT WORK
    • Restarted computer - DID NOT WORK
    • Turned off/on LG monitor many times - DID NOT WORK
    • Unplugged/plugged back in many different ways - DID NOT WORK
    • Changed the HDMI to DVI cable with a better cable - DID NOT WORK
    • Installed BootCamp with Windows 7 - *BOTH WORK 100%*
    • Rebooted to OS X 10.6.7 (Snow Leopard) - DID NOT WORK
    • Installed Windows XP - *BOTH WORKED 100%*
    • Reinstalled OS X 10.6.4 (Snow Leopard) - *BOTH WORKED 100%*
    • Updated OS X from 10.6.4 to 10.6.7 - DID NOT WORK
    Seems to be a driver problem with the new update (10.6.7). I will not update again till drivers are fixed.

  • Mini Display port DVI adapter not working on Thunderbolt Port

    For some time I've been using a mini display port to DVI adapter on an slightly older MBP to connect to my HD TV.  I recently purchased a MBP with a Thunderbolt port and when I try to connect it to my TV via my mini-display-port-DVI adapter things are not working properly.  The MBP is seeing the Philips TV but it isn't listing all the display modes and I'm not able to send any video to it.  Does the Thunderbolt port require a new display port to DVI adapter?

    Let me be clearer; I've got the MDP-DVI adapter connected to a cable that is DVI on one end and HDMI on the other.  I've got both laptops so I can compare side by side.  I plug in the MDP-DVI adapter to the old laptop and all works well; I plug it into the new laptop and while the laptop does see the TV, the display modes for it are all 1080p which is wrong I don't see any desktop image on the TV unlike when I plug it into the older laptop.  This is very disappointing as I expect things to just work with Apple products.

Maybe you are looking for