Minimum Req for XI

Hi All,
Could you please list out the minimum system requirments to install XI.
Regards,
Ashish

Hi Ashish,
You need to have a minimum of 2 GB RAM with 60 GB in inst drive. However, when starting with an XI project the question for hardware demand is often raised. To answer this question we have XI Quicksizer.
Sizing means determining the hardware requirements of an SAP System such as network bandwidth, physical memory, CPU power, and I/O capacity.
The Quick Sizer is a tool jointly developed by SAP and its hardware partners to help customers get an idea about initial sizing. It is free of cost. The Quick Sizer is a Web-based tool designed to make the sizing of mySAP Business Suite easier and faster. It has been developed by SAP in close cooperation with all platform partners and is free of cost.
You can use the sizing tool available in :-
http://service.sap.com/sizing
Regards.
Praveen

Similar Messages

PSU Req for GTX970 Gaming

I know that the minimum PSU req. for this card is 500W.
However, my system is a mATX MSI B85 motherboard with a i5 4570s, so it drains very little power as it is. I'm currently using ATI HD6850 and it never goes over 200W at the wall. (Idle's at 40W, 110W playback)
My PSU is a Silverstone SFX 450W 80 Bronze. (2x6 pin). Do you think my PSU will be able to power this card without problems? Will it be sensitive to the coil whine problems?
I'm waiting for the GTX970 "Lite" which is not overcloked" just to keep things under control power wise, but the GTX 970 Gaming edition seems appealing as soon as it comes back to the market.
Any thoughts? Thanks!

Quote from: badboy2k on 11-October-14, 07:44:08
+12V power needs for the 2 cards mentioned:
Radeon HD 6950 - 30A and a 500W PSU minimum
GeForce GTX 970 - 28A and a 500W PSU minimum
as for your PSU it has alot more Ripple on the +12v Rail then a more quality unit!
a Corsair CX450W PSU has around 20Mv ripple at full load
yours has around 140Mv ripple (7 Times more) which is high and I would suspect quite audible Whine would be induced!
Thanks for your reply.
My Silverstone PSU is "supposed" to be a quality PSU. I needed a SFX PSU for my case and there aren't many options anyway.
the +12V is 36A.
Where did you get those ripple measurements from?

How to set minimum size for the 'location' box in toolbars?

I reorganized my toolbars by merging the location and tabs bar. I have the location on the left hand side and the tabs *next* to it, like this:
[ (<)(>) [LOCATION] /tab\/tab\/tab\ ]
Unfortunately when the number of tabs increases, the location box becomes so small that I cannot even see the url of the site I'm in...
Is there a way to force a minimum width for the location box? I couldn't find a setting in about:config for it (I imagine that this would be a browser.urlbar setting)

You rock! The combination of fixed width tabs with the stylish Add-on, and the single line of script below just made my day!
#main-window[sizemode="maximized"] #TabsToolbar, #TabsToolbar > #urlbar-container { min-width: 350px; }
Many thanks!

What are the real minimum requirements for Mountain Lion?

What are the real minimum requirements for Mountain Lion. Currently running Snow Leopard. I have a late 2006 Model: iMac6,1. Specs: 2.33 GHz Core 2 Duo, 3 GB 667 MHz DDR2, and the optional nVidia GeForce 7600GT c/w 256MB GDDR2. The advertisement is stating a 2007 model as the minumum, however the fastest 2006 Gen Plastic iMac should be faster then the slowest 2007 Gen Aluminum iMac7,1?

From a previous posting from some else, I saw it was the 32bit versus 64bit video card driver being the issue. I was wondering if the optional video card I have installed also was limited to the 32bit issue. 64bit drivers exist for the 7600 GT GPU.

I'm trying to download the trial version of Adobe Illustrator. An error message says that the OS does not meet the minimum system requirements for the installer. 10.6.0 is the minimum required for installation. How do I get my mac to be a 10.6.0 ?

I'm trying to download the trial version of Adobe Illustrator. An error message says that the OS does not meet the minimum system requirements for the installer. 10.6.0 is the minimum required for installation. How do I get my mac to be a 10.6.0 ? Right now I have a 10.5.8 is there a way to upgrade or something?

Buy the Snow Leopard retail installer (http://store.apple.com/us/product/MC573Z/A?fnode=MTY1NDAzOA).
That will take you to 10.6.3.
If required you can then use the combo updater to get to the latest version, 10.6.8 (http://support.apple.com/kb/DL1399)
SL system reqmts;

Minimum Spec for FCE4: cheapest Mac Mini?

I'm looking to get a Mac Mini primarily to record endoscopic video (s-video) via a Canopus ADVC 55 using Final Cut Express. Looking at the minimum requirements for FCE4 it seems the cheapest model with 2GB RAM should be way more than adequate. The specs don't even mention hard drive speed.
However, by todays standards 2GB is fairly minimal, and the 5400 rpm 2.5" hard drives are quite slow. I have used FCE4 on an original white MacBook and frequently got dropped frames when recording (which lost the entire recording each time), a problem that disappeared when I upgraded to a MacBook Pro.
If used purely for recording, and if the hard drive is regularly cleared (video files moved to a Mac Pro for processing) will there be any problems with only 2GB of RAM, or the speed of the hard drive?
Because this is to go into an operating theatre where space is limited, I would prefer that I don't have the hassle or expense of an external Firewire hard drive (and I'm guessing the single Firewire port may be an issue).
Looking at the spec for the Mac Mini Server it looks much more suitable, 2 7400 rpm hard drives, 4GB RAM - but cost wise I think will be harder to persuade my employer!

I'm afraid I cannot really answer your question as I don't need / use the features of the snow leopard server software. Hardware wise the differences add more ram, 2 hard drives (and they're faster) but no optical drive (with the option of connecting one externally). Other than that it comes with snow leopard server which allows you to use it as a normal mac, but additionally can be set up as mail server, file server, and a bunch of utilities to help manage this (not sure how accurate my understanding of the differences between the software).
Incidentally the normal version of snow leopard has a certain amount of server functionality anyway, eg filesharing, web hosting etc. I think the server edition mainly provides lots of tools to take this further.
It definitely would require configuring, and you would need other stuff like a router to connect the computers together which would also need configuring. But not much different to linking a bunch of normal macs together (if you're usinng it as a file server). I might be wrong but I don't think the connected computers can run on it's OS like some of these dumb terminal systems can.
Message was edited by: bilbo_baggins

The installed version of SQL Server could not be verified or is not supported. Verify that the computer and the installed version of SQL Server meet the minimum requirements for installation

Hi Guys,
Currently i am trying to install SCOM2012R2 with SQL 2012 SP1. When i proceed with SCOM installation, getting an error
"The installed version of SQL Server could not be verified or is not supported. Verify that the computer and the installed version of SQL Server meet the minimum requirements for installation, and that the firewall settings are correct. See the Supported
Configurations document for further information.
SQL Collation i selected as per System Center2012 guide SQL_Latin1_General_CP1_CI_AS
Can some one please help me on this?
Regards
Kris
Kris

Hi,
Please check logs for further information. Let us know what the logs says:
http://www.systemcentercentral.com/opsmgr-2012-my-installation-failed-what-log-files-do-i-read-and-where-can-i-find-them/
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Minimum requirements for home server

I am looking to get a cheap iMac, Mini or iBook to use as a home server to run iTunes 24/7. I will be attaching an external HD for storage space for my media and will stream wirelessly to Apple TV over 802.11g using an Airport Express. What would be the minimum requirement for such a setup? Would the minimum requirement be what the latest version of iTunes require?
Message was edited by: Mac4lfe

Hi Mac4lfe: If you want to SYNCH between the Mac and the ATV, then any G3 will do, just expect the synching to be slow. If you want to STREAM from the Mac to ATV, then a G3 will do for music but not for video. If you want to stream video, a G4 will do, but you will get a lot of beachballs when you do anything on iTunes and sometimes the streaming will fail. I suggest you get the cheapest Intel Mac, you will have a much better experience when streaming. Lastly, remember you will need a screen for the Mini, there will always be warnings, error messages, updates, etc in iTunes that you need a screen, mouse and keyboard for. Very lastly, you can just get the ATV and buy music, TV shows, Movies and rent movies without a Mac. 160GP shall be enough. I have 40 movies, 20 full TV seasons and 6000 songs and am just over 400GB.

Minimum implementation for SMTP-ESMTP clients

Hi,
if I want to develop a Mail client I can use SMTP/ESMTP. I read already some of the RFC-Specs, but I cannot find an advice for the minimum implementation for a client - just for servers.
Is the minimum number of commands the same as for the servers (7 commands for SMTP and 9 commands for ESMTP) ?
Thanks for any help.
BR

Simple config...
rserver host EXCHANGE001
ip address 10.2.3.101
probe PING_EXCHANGE
inservice
rserver host EXCHANGE002
ip address 10.2.3.102
probe PING_EXCHANGE
rserver host EXCHANGE003
ip address 10.2.3.103
probe PING_EXCHANGE
rserver host EXCHANGE004
ip address 10.2.3.104
probe PING_EXCHANGE
serverfarm host EXCHANGE
description EXCHANGE SERVERS
predictor hash address
probe PR-EXCHANGE-HTTPS
rserver EXCHANGE001
    inservice
rserver EXCHANGE002
rserver EXCHANGE003
rserver EXCHANGE004
class-map match-all EXCHANGE-VIP
10 match virtual-address 10.2.3.100 tcp any
sticky ip-netmask 255.255.255.255 address both EXCHANGE-STICKY
timeout 20
replicate sticky
serverfarm EXCHANGE
policy-map type loadbalance first-match EXCHANGE-VIP
class class-default
    sticky-serverfarm EXCHANGE-STICKY
policy-map multi-match EXCHANGE_POL
class EXCHANGE-VIP
    loadbalance vip inservice
    loadbalance policy EXCHANGE-VIP
    loadbalance vip icmp-reply
NB: Only rsever EXCHANGE001 is active in the serverfarm.

Condition type PMIN Minimum Price for material

Hello
We have a requirement where we need to maintain minimum price of material in master.
Whenever in sales order price is entered and is lower than minium price for material maintained it should automatically add the difference as surcharge. If the price maintained is more than the minimum price maintained it should not do anything.
I guess we have to use Ctype PMIN for this. I amy using this condition type have created a condition record and maintained a minimum price for this material f09 as rs 1000
Now when i am creating sales order price picked up from pricing condition record for that customer is 500 . Now it should automatically add Rs 500 in condition line item for condition type PMIN.
What is happening is it is showing me my base price as 500 and it is adding PMIN as 1000 to the base price and showing total base price as 1500
If price maintained in pricing condition record is more than 1000 for ex 1200 even then too it is adding PMIN as 1000 and showing total base price as 2200.
Please let me know what am i missing...
Regards
SANJEEV

-T code VK11 - Maintain condition records - You can use the upper and lower limits functionality in the condition records for those specific materials.
-Also Make this condition type as mandatory then check it out.
Regards

After updating to lion installed graphics card does not meet minimum requirements for aperture

Hello,
I updated to OSX lion yesterday. and Apterture is given me this error message. "The installed graphics card does not meet the minimum requirements for Aperture.   I tried the Option Command Open app thing to try rebuild the database. But nothing happens when I try opeing the app using those combo key's So I removed the app using mackeeper and tried reinstalling it. still same issue.
I have following machine
Model Name:          MacBook Pro
Model Identifier:          MacBookPro8,2
Processor Name:          Intel Core i7
Processor Speed:          2.3 GHz
Number of Processors:          1
Total Number of Cores:          4
L2 Cache (per Core):          256 KB
L3 Cache:          8 MB
Memory:          8 GB
Boot ROM Version:          MBP81.0047.B0E
SMC Version (system):          1.69f1
Serial Number (system):          C02F94ETDMGG
Hardware UUID:          132AE53D-0766-5E17-9F54-ED935D6F7AB3
Sudden Motion Sensor:
State:          Enabled
Chipset Model:          AMD Radeon HD 6750M
Type:          GPU
Bus:          PCIe
PCIe Lane Width:          x8
VRAM (Total):          1024 MB
Vendor:          ATI (0x1002)
Device ID:          0x6741
Revision ID:          0x0000
ROM Revision:          113-C0170L-521
gMux Version:          1.9.23
EFI Driver Version:          01.00.521
Displays:
Color LCD:
Resolution:          1680 x 1050
Pixel Depth:          32-Bit Color (ARGB8888)
Main Display:          Yes
Mirror:          Off
Online:          Yes
Built-In:          Yes
VX2245wm:
Resolution:          1680 x 1050 @ 60 Hz
Pixel Depth:          32-Bit Color (ARGB8888)
Display Serial Number:          QD0064002266
Mirror:          Off
Online:          Yes
Rotation:          Supported
Adapter Type:          Apple Mini DisplayPort To VGA Adapter
Adapter Firmware Version:          1.03
Display Connector:
Status:          No Display Connected

HAve you tried disconnecting the external monitor rebooting and then runnig Aperture?

Set Minimum amount for non LVA Asset Class

Dear all,
Is it possible to set a minimum amount for asset classes other LVA asset class?
Thanks & regards.

Dear Jay,
I didn't see a configuration setting to set the minimum amount for asset class even for LVA asset class - in LVA asset class we will specify the maximum amount only not the minimum amount.
I think through SAP standard setting this is not possible and may require some enhancements for this.
Regards,
Kiran Yelamarthi

Setting a minimum height for a dyanmic subform

I am creating a form that is reading in a set of instructions from XML. I would like to limit the instructions to 2 per page. Is there a way I can set a minimum height for the subform, so it will at least be 1/2 the page?

Hi,
If that's the case, then you could size each field in the Design view so that each field takes up have a page. Then in the Layout tab select "expand to fit height" (should also have allowed multiple lines in the Object / Field tab).
Then when you import the XML, short instructions will appear two per page, while longer ones will flow onto following pages. If the fields are set to half a page then you should not get more than 2 on a page.
Hope that is of help,
Niall

Minimum Configuration for SDM.

Hi I would like to know what is the minimum configuration for access by sdm my router with volares manufactured, is a 877. Greetings

Your 877 device is sufficent . Make sure you are using IOS 12.3(8)YI or 12.4(2)T or later releases .
More info:Cisco Router and Security Device Manager Introduction
http://www.cisco.com/en/US/products/sw/secursw/ps5318/tsd_products_support_series_home.html

Unexpected minimum value for SHEAPTHRES_SHR

Hi Folks - We keep getting the following message every 30 seconds on our BI QA server.
2009-08-24-07.26.17.263989-240 E78429A607         LEVEL: Warning
PID     : 930014               TID : 15425       PROC : db2sysc 0
INSTANCE: db2bq1               NODE : 000         DB   : BQ1
APPHDL : 0-28423              APPID: *LOCAL.DB2.090808073504
AUTHID : DB2BQ1
EDUID   : 15425                EDUNAME: db2stmm (BQ1) 0
FUNCTION: DB2 UDB, Self tuning memory manager, stmmComputeMinSHEAPTHRES, probe:836
MESSAGE : Unexpected minimum value for SHEAPTHRES_SHR - value automatically
          corrected - 122423 - 2448 - 338887 - 9180 - 3 - 0 - 3.000000 -
           1 - 31 - 271110 - 630
I am pretty sure this will have performance impact on the database as the database manager has to keep changing the SHEAPTHRES_SHR value every 30 seconds back to the correct value. Has any one seen this before? Turning off STMM is not an option. We do not want to hard code SHEAPTHRES_SHR value as the loads on BI are not-predictable in the environment.
Pl advise.
Thanks.

The output of the SQL statement shows:
MAX_PARTITION_MEM: Maximum allowed "instance_memory" (this will correspond with the current setting of instance_memory in bytes)
CURRENT_PARTITION_MEM: Current total memory allocation (in bytes)
PEAK_PARTITION_MEM: HWM total memory allocation (in bytes)
The bug with the STMM memory calculation was first fixed with version 9.5 FP4 so you might have to upgrade your instances to FP4. In fact, if I am not mistaken, SAP withdrew FP3 due to a hiper apar which can potentially impact SAP systems.
Also as far as the values in the output of the query and db2pd are concerned, they are not different. The output of the query is expressed in bytes whereas the output of pd is expressed in KB.
$$ db2pd -dbptnmem
Memory Limit:         36000000 KB (which is 36864000000 bytes)
Current usage:        31746944 KB (which is 32508870656 bytes)
HWM usage:            35704320 KB (which is 36561223680 bytes)
Regards,
Sameer

Minimum Req for XI

Similar Messages

Maybe you are looking for