MiniSap WAS 6.40 - Services Setup
After using the transation SICK i've activated all the services in the instance profile NSP_DVEBMGS00_01P as follow:
rdisp/wp_no_dia = 2
rdisp/wp_no_btc = 1
rdisp/wp_no_vb = 1
rdisp/wp_no_vb2 = 1
rdisp/wp_no_enq = 1
rdisp/wp_no_spo = 1
However this requests a lot of memory resources.
I wonder if anyone could let me know which are of these services are mandatory.
Best Regards,
José Antã
The only 2 that are required on any SAP CI instance are
rdisp/wp_no_dia = 2
rdisp/wp_no_vb = 1
rdisp/wp_no_enq = 1
all others are optional depending on the use of the instance.
Regards,
Paul McCrimmon
Similar Messages
-
Pre-check for cluster services setup was unsuccessful on all the nodes.
hi
when i am running the fixup script getting:
if i run cluvfy again i am getting another fixup script.what exactly to do?
[root@rac-1 grid1]# sh /tmp/CVU_11.2.0.1.0_grid1/runfixup.sh
Response file being used is :/tmp/CVU_11.2.0.1.0_grid1/fixup.response
Enable file being used is :/tmp/CVU_11.2.0.1.0_grid1/fixup.enable
Log file location: /tmp/CVU_11.2.0.1.0_grid1/orarun.log
uid=1100(grid1) gid=1000(oinstall) groups=1000(oinstall),1100(dba),1200(asmdba),1300(asmadmin),1202(asmoper)
grid1 hard nproc 16384
Value of MAX PROCESSES HARDLIMIT in response file is not greater than value in/etc/security/limits.conf. Hence not changing it.
grid1 hard nofile 65536
Value of FILE OPEN MAX HARDLIMIT in response file is not greater than value in /etc/security/limits.conf.Hence not changing it.
uid=1100(grid1) gid=1000(oinstall) groups=1000(oinstall),1100(dba),1200(asmdba),1300(asmadmin),1202(asmoper)
[root@rac-1 grid1]#
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "rac-1"
Destination Node Reachable?
rac-2 yes
rac-1 yes
Result: Node reachability check passed from node "rac-1"
Checking user equivalence...
Check: User equivalence for user "grid1"
Node Name Comment
rac-2 passed
rac-1 passed
Result: User equivalence check passed for user "grid1"
Checking node connectivity...
Checking hosts config file...
Node Name Status Comment
rac-2 passed
rac-1 passed
Verification of the hosts config file successful
Interface information for node "rac-2"
Name IP Address Subnet Gateway Def. Gateway HW Address MTU
eth0 192.168.1.3 192.168.1.0 0.0.0.0 192.168.1.1 00:1D:72:39:3A:E4 1500
virbr0 192.168.122.1 192.168.122.0 0.0.0.0 192.168.1.1 00:00:00:00:00:00 1500
eth1 192.168.181.20 192.168.181.0 0.0.0.0 192.168.1.1 00:00:00:00:00:00 1500
Interface information for node "rac-1"
Name IP Address Subnet Gateway Def. Gateway HW Address MTU
eth0 192.168.1.2 192.168.1.0 0.0.0.0 192.168.1.1 00:00:E8:F7:02:B0 1500
eth1 192.168.181.10 192.168.181.0 0.0.0.0 192.168.1.1 00:26:18:59:EE:49 1500
virbr0 192.168.122.1 192.168.122.0 0.0.0.0 192.168.1.1 00:00:00:00:00:00 1500
Check: Node connectivity of subnet "192.168.1.0"
Source Destination Connected?
rac-2:eth0 rac-1:eth0 yes
Result: Node connectivity passed for subnet "192.168.1.0" with node(s) rac-2,rac-1
Check: TCP connectivity of subnet "192.168.1.0"
Source Destination Connected?
rac-1:192.168.1.2 rac-2:192.168.1.3 passed
Result: TCP connectivity check passed for subnet "192.168.1.0"
Check: Node connectivity of subnet "192.168.122.0"
Source Destination Connected?
rac-2:virbr0 rac-1:virbr0 yes
Result: Node connectivity passed for subnet "192.168.122.0" with node(s) rac-2,rac-1
Check: TCP connectivity of subnet "192.168.122.0"
Result: TCP connectivity check failed for subnet "192.168.122.0"
Check: Node connectivity of subnet "192.168.181.0"
Source Destination Connected?
rac-2:eth1 rac-1:eth1 yes
Result: Node connectivity passed for subnet "192.168.181.0" with node(s) rac-2,rac-1
Check: TCP connectivity of subnet "192.168.181.0"
Source Destination Connected?
rac-1:192.168.181.10 rac-2:192.168.181.20 passed
Result: TCP connectivity check passed for subnet "192.168.181.0"
Interfaces found on subnet "192.168.1.0" that are likely candidates for VIP are:
rac-2 eth0:192.168.1.3
rac-1 eth0:192.168.1.2
Interfaces found on subnet "192.168.122.0" that are likely candidates for a private interconnect are:
rac-2 virbr0:192.168.122.1
rac-1 virbr0:192.168.122.1
Interfaces found on subnet "192.168.181.0" that are likely candidates for a private interconnect are:
rac-2 eth1:192.168.181.20
rac-1 eth1:192.168.181.10
Result: Node connectivity check passed
Check: Total memory
Node Name Available Required Comment
rac-2 1.96GB (2050416.0KB) 1.5GB (1572864.0KB) passed
rac-1 1.96GB (2058984.0KB) 1.5GB (1572864.0KB) passed
Result: Total memory check passed
Check: Available memory
Node Name Available Required Comment
rac-2 1.7GB (1780600.0KB) 50MB (51200.0KB) passed
rac-1 1.56GB (1636896.0KB) 50MB (51200.0KB) passed
Result: Available memory check passed
Check: Swap space
Node Name Available Required Comment
rac-2 4GB (4194296.0KB) 2.93GB (3075624.0KB) passed
rac-1 4GB (4192956.0KB) 2.95GB (3088476.0KB) passed
Result: Swap space check passed
Check: Free disk space for "rac-2:/tmp"
Path Node Name Mount point Available Required Comment
/tmp rac-2 / 24.03GB 1GB passed
Result: Free disk space check passed for "rac-2:/tmp"
Check: Free disk space for "rac-1:/tmp"
Path Node Name Mount point Available Required Comment
/tmp rac-1 / 16.54GB 1GB passed
Result: Free disk space check passed for "rac-1:/tmp"
Check: User existence for "grid1"
Node Name Status Comment
rac-2 exists passed
rac-1 exists passed
Result: User existence check passed for "grid1"
Check: Group existence for "oinstall"
Node Name Status Comment
rac-2 exists passed
rac-1 exists passed
Result: Group existence check passed for "oinstall"
Check: Group existence for "dba"
Node Name Status Comment
rac-2 exists passed
rac-1 exists passed
Result: Group existence check passed for "dba"
Check: Membership of user "grid1" in group "oinstall" [as Primary]
Node Name User Exists Group Exists User in Group Primary Comment
rac-2 yes yes yes yes passed
rac-1 yes yes yes yes passed
Result: Membership check for user "grid1" in group "oinstall" [as Primary] passed
Check: Membership of user "grid1" in group "dba"
Node Name User Exists Group Exists User in Group Comment
rac-2 yes yes no failed
rac-1 yes yes yes passed
Result: Membership check for user "grid1" in group "dba" failed
Check: Run level
Node Name run level Required Comment
rac-2 5 3,5 passed
rac-1 5 3,5 passed
Result: Run level check passed
Check: Hard limits for "maximum open file descriptors"
Node Name Type Available Required Comment
rac-2 hard 65536 65536 passed
rac-1 hard 65536 65536 passed
Result: Hard limits check passed for "maximum open file descriptors"
Check: Soft limits for "maximum open file descriptors"
Node Name Type Available Required Comment
rac-2 soft 1024 1024 passed
rac-1 soft 65536 1024 passed
Result: Soft limits check passed for "maximum open file descriptors"
Check: Hard limits for "maximum user processes"
Node Name Type Available Required Comment
rac-2 hard 16384 16384 passed
rac-1 hard 16384 16384 passed
Result: Hard limits check passed for "maximum user processes"
Check: Soft limits for "maximum user processes"
Node Name Type Available Required Comment
rac-2 soft 2047 2047 passed
rac-1 soft 16384 2047 passed
Result: Soft limits check passed for "maximum user processes"
Check: System architecture
Node Name Available Required Comment
rac-2 x86_64 x86_64 passed
rac-1 x86_64 x86_64 passed
Result: System architecture check passed
Check: Kernel version
Node Name Available Required Comment
rac-2 2.6.18-92.el5 2.6.18 passed
rac-1 2.6.18-164.el5 2.6.18 passed
WARNING:
PRVF-7524 : Kernel version is not consistent across all the nodes.
Kernel version = "2.6.18-164.el5" found on nodes: rac-1.
Kernel version = "2.6.18-92.el5" found on nodes: rac-2.
Result: Kernel version check passed
Check: Kernel parameter for "semmsl"
Node Name Configured Required Comment
rac-2 250 250 passed
rac-1 250 250 passed
Result: Kernel parameter check passed for "semmsl"
Check: Kernel parameter for "semmns"
Node Name Configured Required Comment
rac-2 32000 32000 passed
rac-1 32000 32000 passed
Result: Kernel parameter check passed for "semmns"
Check: Kernel parameter for "semopm"
Node Name Configured Required Comment
rac-2 100 100 passed
rac-1 100 100 passed
Result: Kernel parameter check passed for "semopm"
Check: Kernel parameter for "semmni"
Node Name Configured Required Comment
rac-2 142 128 passed
rac-1 142 128 passed
Result: Kernel parameter check passed for "semmni"
Check: Kernel parameter for "shmmax"
Node Name Configured Required Comment
rac-2 1049812992 536870912 passed
rac-1 4398046511104 536870912 passed
Result: Kernel parameter check passed for "shmmax"
Check: Kernel parameter for "shmmni"
Node Name Configured Required Comment
rac-2 4096 4096 passed
rac-1 4096 4096 passed
Result: Kernel parameter check passed for "shmmni"
Check: Kernel parameter for "shmall"
Node Name Configured Required Comment
rac-2 3279547 2097152 passed
rac-1 1073741824 2097152 passed
Result: Kernel parameter check passed for "shmall"
Check: Kernel parameter for "file-max"
Node Name Configured Required Comment
rac-2 6815744 6815744 passed
rac-1 6815744 6815744 passed
Result: Kernel parameter check passed for "file-max"
Check: Kernel parameter for "ip_local_port_range"
Node Name Configured Required Comment
rac-2 between 9000 & 65500 between 9000 & 65500 passed
rac-1 between 9000 & 65500 between 9000 & 65500 passed
Result: Kernel parameter check passed for "ip_local_port_range"
Check: Kernel parameter for "rmem_default"
Node Name Configured Required Comment
rac-2 262144 262144 passed
rac-1 4194304 262144 passed
Result: Kernel parameter check passed for "rmem_default"
Check: Kernel parameter for "rmem_max"
Node Name Configured Required Comment
rac-2 4194304 4194304 passed
rac-1 4194304 4194304 passed
Result: Kernel parameter check passed for "rmem_max"
Check: Kernel parameter for "wmem_default"
Node Name Configured Required Comment
rac-2 262144 262144 passed
rac-1 262144 262144 passed
Result: Kernel parameter check passed for "wmem_default"
Check: Kernel parameter for "wmem_max"
Node Name Configured Required Comment
rac-2 1048576 1048576 passed
rac-1 1048576 1048576 passed
Result: Kernel parameter check passed for "wmem_max"
Check: Kernel parameter for "aio-max-nr"
Node Name Configured Required Comment
rac-2 3145728 1048576 passed
rac-1 3145728 1048576 passed
Result: Kernel parameter check passed for "aio-max-nr"
Check: Package existence for "ocfs2-tools-1.2.7"
Node Name Available Required Comment
rac-2 ocfs2-tools-1.2.7-1.el5 ocfs2-tools-1.2.7 passed
rac-1 ocfs2-tools-1.4.2-1.el5 ocfs2-tools-1.2.7 passed
Result: Package existence check passed for "ocfs2-tools-1.2.7"
Check: Package existence for "make-3.81"
Node Name Available Required Comment
rac-2 make-3.81-3.el5 make-3.81 passed
rac-1 make-3.81-3.el5 make-3.81 passed
Result: Package existence check passed for "make-3.81"
Check: Package existence for "binutils-2.17.50.0.6"
Node Name Available Required Comment
rac-2 binutils-2.17.50.0.6-6.el5 binutils-2.17.50.0.6 passed
rac-1 binutils-2.17.50.0.6-12.el5 binutils-2.17.50.0.6 passed
Result: Package existence check passed for "binutils-2.17.50.0.6"
Check: Package existence for "gcc-4.1.2"
Node Name Available Required Comment
rac-2 gcc-4.1.2-42.el5 gcc-4.1.2 passed
rac-1 gcc-4.1.2-46.el5 gcc-4.1.2 passed
Result: Package existence check passed for "gcc-4.1.2"
Check: Package existence for "libaio-0.3.106 (i386)"
Node Name Available Required Comment
rac-2 libaio-0.3.106-3.2 (i386) libaio-0.3.106 (i386) passed
rac-1 libaio-0.3.106-3.2 (i386) libaio-0.3.106 (i386) passed
Result: Package existence check passed for "libaio-0.3.106 (i386)"
Check: Package existence for "libaio-0.3.106 (x86_64)"
Node Name Available Required Comment
rac-2 libaio-0.3.106-3.2 (x86_64) libaio-0.3.106 (x86_64) passed
rac-1 libaio-0.3.106-3.2 (x86_64) libaio-0.3.106 (x86_64) passed
Result: Package existence check passed for "libaio-0.3.106 (x86_64)"
Check: Package existence for "glibc-2.5-24 (i686)"
Node Name Available Required Comment
rac-2 glibc-2.5-24 (i686) glibc-2.5-24 (i686) passed
rac-1 glibc-2.5-42 (i686) glibc-2.5-24 (i686) passed
Result: Package existence check passed for "glibc-2.5-24 (i686)"
Check: Package existence for "glibc-2.5-24 (x86_64)"
Node Name Available Required Comment
rac-2 glibc-2.5-24 (x86_64) glibc-2.5-24 (x86_64) passed
rac-1 glibc-2.5-42 (x86_64) glibc-2.5-24 (x86_64) passed
Result: Package existence check passed for "glibc-2.5-24 (x86_64)"
Check: Package existence for "compat-libstdc++-33-3.2.3 (i386)"
Node Name Available Required Comment
rac-2 compat-libstdc++-33-3.2.3-61 (i386) compat-libstdc++-33-3.2.3 (i386) passed
rac-1 compat-libstdc++-33-3.2.3-61 (i386) compat-libstdc++-33-3.2.3 (i386) passed
Result: Package existence check passed for "compat-libstdc++-33-3.2.3 (i386)"
Check: Package existence for "compat-libstdc++-33-3.2.3 (x86_64)"
Node Name Available Required Comment
rac-2 compat-libstdc++-33-3.2.3-61 (x86_64) compat-libstdc++-33-3.2.3 (x86_64) passed
rac-1 compat-libstdc++-33-3.2.3-61 (x86_64) compat-libstdc++-33-3.2.3 (x86_64) passed
Result: Package existence check passed for "compat-libstdc++-33-3.2.3 (x86_64)"
Check: Package existence for "elfutils-libelf-0.125 (x86_64)"
Node Name Available Required Comment
rac-2 elfutils-libelf-0.125-3.el5 (x86_64) elfutils-libelf-0.125 (x86_64) passed
rac-1 elfutils-libelf-0.137-3.el5 (x86_64) elfutils-libelf-0.125 (x86_64) passed
Result: Package existence check passed for "elfutils-libelf-0.125 (x86_64)"
Check: Package existence for "elfutils-libelf-devel-0.125"
Node Name Available Required Comment
rac-2 elfutils-libelf-devel-0.125-3.el5 elfutils-libelf-devel-0.125 passed
rac-1 elfutils-libelf-devel-0.137-3.el5 elfutils-libelf-devel-0.125 passed
Result: Package existence check passed for "elfutils-libelf-devel-0.125"
Check: Package existence for "glibc-common-2.5"
Node Name Available Required Comment
rac-2 glibc-common-2.5-24 glibc-common-2.5 passed
rac-1 glibc-common-2.5-42 glibc-common-2.5 passed
Result: Package existence check passed for "glibc-common-2.5"
Check: Package existence for "glibc-devel-2.5 (i386)"
Node Name Available Required Comment
rac-2 glibc-devel-2.5-24 (i386) glibc-devel-2.5 (i386) passed
rac-1 glibc-devel-2.5-42 (i386) glibc-devel-2.5 (i386) passed
Result: Package existence check passed for "glibc-devel-2.5 (i386)"
Check: Package existence for "glibc-devel-2.5 (x86_64)"
Node Name Available Required Comment
rac-2 glibc-devel-2.5-24 (x86_64) glibc-devel-2.5 (x86_64) passed
rac-1 glibc-devel-2.5-42 (x86_64) glibc-devel-2.5 (x86_64) passed
Result: Package existence check passed for "glibc-devel-2.5 (x86_64)"
Check: Package existence for "glibc-headers-2.5"
Node Name Available Required Comment
rac-2 glibc-headers-2.5-24 glibc-headers-2.5 passed
rac-1 glibc-headers-2.5-42 glibc-headers-2.5 passed
Result: Package existence check passed for "glibc-headers-2.5"
Check: Package existence for "gcc-c++-4.1.2"
Node Name Available Required Comment
rac-2 gcc-c++-4.1.2-42.el5 gcc-c++-4.1.2 passed
rac-1 gcc-c++-4.1.2-46.el5 gcc-c++-4.1.2 passed
Result: Package existence check passed for "gcc-c++-4.1.2"
Check: Package existence for "libaio-devel-0.3.106 (i386)"
Node Name Available Required Comment
rac-2 libaio-devel-0.3.106-3.2 (i386) libaio-devel-0.3.106 (i386) passed
rac-1 libaio-devel-0.3.106-3.2 (i386) libaio-devel-0.3.106 (i386) passed
Result: Package existence check passed for "libaio-devel-0.3.106 (i386)"
Check: Package existence for "libaio-devel-0.3.106 (x86_64)"
Node Name Available Required Comment
rac-2 libaio-devel-0.3.106-3.2 (x86_64) libaio-devel-0.3.106 (x86_64) passed
rac-1 libaio-devel-0.3.106-3.2 (x86_64) libaio-devel-0.3.106 (x86_64) passed
Result: Package existence check passed for "libaio-devel-0.3.106 (x86_64)"
Check: Package existence for "libgcc-4.1.2 (i386)"
Node Name Available Required Comment
rac-2 libgcc-4.1.2-42.el5 (i386) libgcc-4.1.2 (i386) passed
rac-1 libgcc-4.1.2-46.el5 (i386) libgcc-4.1.2 (i386) passed
Result: Package existence check passed for "libgcc-4.1.2 (i386)"
Check: Package existence for "libgcc-4.1.2 (x86_64)"
Node Name Available Required Comment
rac-2 libgcc-4.1.2-42.el5 (x86_64) libgcc-4.1.2 (x86_64) passed
rac-1 libgcc-4.1.2-46.el5 (x86_64) libgcc-4.1.2 (x86_64) passed
Result: Package existence check passed for "libgcc-4.1.2 (x86_64)"
Check: Package existence for "libstdc++-4.1.2 (i386)"
Node Name Available Required Comment
rac-2 libstdc++-4.1.2-42.el5 (i386) libstdc++-4.1.2 (i386) passed
rac-1 libstdc++-4.1.2-46.el5 (i386) libstdc++-4.1.2 (i386) passed
Result: Package existence check passed for "libstdc++-4.1.2 (i386)"
Check: Package existence for "libstdc++-4.1.2 (x86_64)"
Node Name Available Required Comment
rac-2 libstdc++-4.1.2-42.el5 (x86_64) libstdc++-4.1.2 (x86_64) passed
rac-1 libstdc++-4.1.2-46.el5 (x86_64) libstdc++-4.1.2 (x86_64) passed
Result: Package existence check passed for "libstdc++-4.1.2 (x86_64)"
Check: Package existence for "libstdc++-devel-4.1.2 (x86_64)"
Node Name Available Required Comment
rac-2 libstdc++-devel-4.1.2-42.el5 (x86_64) libstdc++-devel-4.1.2 (x86_64) passed
rac-1 libstdc++-devel-4.1.2-46.el5 (x86_64) libstdc++-devel-4.1.2 (x86_64) passed
Result: Package existence check passed for "libstdc++-devel-4.1.2 (x86_64)"
Check: Package existence for "sysstat-7.0.2"
Node Name Available Required Comment
rac-2 sysstat-7.0.2-1.el5 sysstat-7.0.2In both node oracle user & group should be same but in your case looks different.
Once again check your user & group.
Babu -
Yesterday while on WiFi at an international airport, I suddenly lost content in Safari. A window popup suggested that someone was trying to spoof setup.iCloud. After arriving home to my own network, Safari still was acting strange. Do I need to be concerned with possible malware or other destructive software remaining on my iPad?
Hi massmercury,
I want to apologize for your experience here with the service center. I am moving forward to have your case escalated for further review. Please see my private message. I will be your point of contact until our Customer Advocate team reaches out to you.
Best regards,
Bgriffin2
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter! -
To begin, what ADA-compliant options are available to work with a service representative? I've never found the online chat service support to be available during my waking hours after checking over the last week. I can't find a contact email for support, either. I've been instructed on several occasions that I will need to make a voice call for customer service, but unfortunately, this will not be possible. I will require text-format assistance from customer support to address two issues which I am unable to solve on my own:
1) I was charged for service following the cancellation of my service; this includes a period following cancellation during which no service was provided. After working with a representative in person, I was told that my final bill would be adjusted to reflect the legally billable amount. This was three weeks ago and I haven't received a response, and I haven't been able to find a way to pursue a resolution - What can I do to help move this process forward?
2) It appears I will be unable to pay my bill after this dispute has been reviewed. My phone number is no longer with Verizon. The online bill payment login requires a phone number - I have never been provided with any other account number. Unfortunately, Verizon appears to close access to online bill payment when the phone number is transferred, even to accounts with unpaid invoice amounts. How can I pay my bill online?kananga wrote:
To begin, what ADA-compliant options are available to work with a service representative? Good question, and one that I don't know the answer to. Does anything on this page help? Products & Services Overview | Verizon Wireless
1) I was charged for service following the cancellation of my service; this includes a period following cancellation during which no service was provided. Service is normally billed through the end of the billing cycle, whether service is provided or not. "Cancellations will become effective on the last day of that month’s billing cycle, and you are responsible for all charges incurred until then." After working with a representative in person, I was told that my final bill would be adjusted to reflect the legally billable amount. According to their legal docs, the "leagally billable amount" is through the end of the billing cycle. This was three weeks ago and I haven't received a response, and I haven't been able to find a way to pursue a resolution - What can I do to help move this process forward?
2) It appears I will be unable to pay my bill after this dispute has been reviewed. My phone number is no longer with Verizon. The online bill payment login requires a phone number - I have never been provided with any other account number. Unfortunately, Verizon appears to close access to online bill payment when the phone number is transferred, even to accounts with unpaid invoice amounts. How can I pay my bill online? You cannot pay online once the account is cancelled. You will be mailed a paper copy of the final bill, and you can mail a check, or possibly call in and pay over the phone. But online is no longer an option once the account is cancelled. -
Hello,
I am fairly new at Xserve administration, but I got thrown in the fire and i need your help.
My system.log is being hammered with this error:
(com.apple.collabd[15483]): Service setup event to handle failure and will not launch until it fires.
I did my research and it seems to be related to Wiki, but I disabled wiki and restarted and it is still coming up. Any advice would really help
System Version: OS X 10.10.1 (build 14B25)
Server Version: Server 4.0.3 (Build 14S350)Try deleting the preferences file
-
WCF service setup with certificate authentication error
I have a WCF service setup and I need to use a certificate with it and are getting numerous errors when I attempt to browse it. The 1st error I get is "Security settings for this service require 'Anonymous' Authentication but it is not enabled for
the IIS application that hosts this service."
This sounds like a straightforward error message and setting the authentication method in IIS to anonymous resolves being able to browse the service. But I need to use a certificate and setting authentication to anonymous is obviously not right since we
only want those with the proper certificate to access the service. I have all authentication methods in IIS set to disabled when I get the above error message. I have the SSL settings in IIS for the service set to require a certificate as well. I am using
IIS 8.5 as well.
Here is my config file in hoping someone could point me in the correct direction. The service should only work over HTTPS since we are using a certificate and I need the meta data exposed as well hence the mexHttpBinding. I have searched the web but no solution
is working. Any help is appreciated.
<?xml version="1.0" encoding="UTF-8"?>
<configuration>
<configSections>
<sectionGroup name="applicationSettings" type="System.Configuration.ApplicationSettingsGroup, System, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089">
<section name="HEALookupProxy.Properties.Settings" type="System.Configuration.ClientSettingsSection, System, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089" requirePermission="false" />
</sectionGroup>
</configSections>
<appSettings>
<add key="aspnet:UseTaskFriendlySynchronizationContext" value="true" />
</appSettings>
<system.web>
<compilation targetFramework="4.5.1" />
<httpRuntime targetFramework="4.5.1" />
<authentication mode="None"></authentication>
</system.web>
<system.serviceModel>
<serviceHostingEnvironment multipleSiteBindingsEnabled="true">
<baseAddressPrefixFilters >
<add prefix="https"/>
</baseAddressPrefixFilters>
</serviceHostingEnvironment>
<services>
<service name="HEALookupProxy.HEALookupService" behaviorConfiguration="HEALookupServiceBehavior">
<endpoint address="" binding="wsHttpBinding" contract="HEALookupProxy.IHEALookupService" bindingConfiguration="HEALookupConfig" />
<endpoint contract="IMetadataExchange" binding="mexHttpBinding" address="mex" />
</service>
</services>
<bindings>
<wsHttpBinding>
<binding name="HEALookupConfig">
<security mode="TransportWithMessageCredential">
<transport clientCredentialType="Certificate"/>
</security>
</binding>
</wsHttpBinding>
</bindings>
<behaviors>
<serviceBehaviors>
<behavior name="HEALookupServiceBehavior">
<serviceMetadata httpsGetEnabled="true"/>
<serviceDebug includeExceptionDetailInFaults="false" />
<serviceCredentials>
<serviceCertificate x509FindType="FindBySubjectName" storeLocation="LocalMachine" storeName="My" findValue="certnameremoved" />
</serviceCredentials>
</behavior>
</serviceBehaviors>
</behaviors>
</system.serviceModel>
<system.webServer>
<modules runAllManagedModulesForAllRequests="true" />
<!--
To browse web app root directory during debugging, set the value below to true.
Set to false before deployment to avoid disclosing web app folder information.
-->
<directoryBrowse enabled="false" />
<security>
<authorization>
<remove users="*" roles="" verbs="" />
<add accessType="Allow" users="user1, user2" />
</authorization>
</security>
</system.webServer>
</configuration>Hi spark29er,
>>The service should only work over HTTPS since we are using a certificate and I need the meta data exposed as well hence the mexHttpBinding.
For creating the HTTPS WCF service, first please change the mexHttpBinding to
mexHttpsBinding as following:
<endpoint contract="IMetadataExchange" binding="mexHttpsBinding" address="mex" />
For more information, please try to refer to:
#Seven simple steps to enable HTTPS on WCF WsHttp bindings:
http://www.codeproject.com/Articles/36705/simple-steps-to-enable-HTTPS-on-WCF-WsHttp-bindi .
Then please try to check the following article about how to do the certificate authentication on HTTPS WCF Service:
http://blogs.msdn.com/b/imayak/archive/2008/09/12/wcf-2-way-ssl-security-using-certificates.aspx .
Besides, setting the
includeExceptionDetailInFaults as false can give us more detailed error information.
Best Regards,
Amy Peng
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
Hi,
I am trying to install certificate services on a windows 2008 server (R2 ENT SP1) with a PCIe nCipher HSM module installed on it. The version of nCipher SW is = 11.30. It is a RootCA, and I am trying to use a key that is already stored in the HSM (I
have done this before with a PCI HSM (older HW version)). I select “Use existing private key” and “Select an existing private key on this computer” on the wizard, then i change the CSP to nCipher and click on "search" the key I am looking for
appears and I select that one. I repeat, I have done this before and it works with a PCI HSM module.
The installation is finished before being prompted to insert the operator cards, and it ends with two errors:
<Error>: Active Directory Certificate Services setup failed with the following error: Overlapped I/O operation is in progress. 0x800703e5 (WIN32: 997)
And:
<Error>: Active Directory Certificate Services setup failed with the following error: The group or resource is not in the correct state to perform the requested operation.
0x8007139f (WIN32: 5023)
The servermanager.log says:
1856: 2014-07-23 18:27:48.195 [CAManager] Sync: Validity period units: Years
1856: 2014-07-23 18:27:48.928 [Provider] Error (Id=0) System.Runtime.InteropServices.COMException (0x800703E5): CCertSrvSetup::Install: Overlapped I/O operation is in progress. 0x800703e5 (WIN32: 997)
at Microsoft.CertificateServices.Setup.Interop.CCertSrvSetupClass.Install()
at Microsoft.Windows.ServerManager.CertificateServer.CertificateServerRoleProvider.Configure(InstallableFeatureInformation featureInfo, DiscoveryResult discoveryResult, ChangeTracker changeTracker)
1856: 2014-07-23 18:27:48.928 [Provider] CAErrorID: 0, CAErrorString: 'Active Directory Certificate Services setup failed with the following error: Overlapped I/O operation is in progress.
0x800703e5 (WIN32: 997)'
1856: 2014-07-23 18:27:48.928 [Provider] Adding error message.
1856: 2014-07-23 18:27:48.928 [Provider] [STAT] For 'Certification Authority':
And:
1856: 2014-07-23 18:27:49.053 [CAWebProxyManager] Sync: Initializing defaults
1856: 2014-07-23 18:27:49.162 [Provider] Error (Id=0) System.Runtime.InteropServices.COMException (0x8007139F): CCertSrvSetup::Install: The group or resource is not in the correct state to perform the requested operation. 0x8007139f (WIN32: 5023)
at Microsoft.CertificateServices.Setup.Interop.CCertSrvSetupClass.Install()
at Microsoft.Windows.ServerManager.CertificateServer.CertificateServerRoleProvider.Configure(InstallableFeatureInformation featureInfo, DiscoveryResult discoveryResult, ChangeTracker changeTracker)
1856: 2014-07-23 18:27:49.162 [Provider] CAErrorID: 0, CAErrorString: 'Active Directory Certificate Services setup failed with the following error: The group or resource is not in the correct
state to perform the requested operation. 0x8007139f (WIN32: 5023)'
1856: 2014-07-23 18:27:49.162 [Provider] Adding error message.
Has anyone experienced this before? Am I missing something here?
Any help will be very appreciated
Thanks in advance
Best regards
Alejandro Lozano VillanuevaHi, thanks for your support.
I have been playing around a bit with some ncipher commands and found this:
C:\Program Files (x86)\nCipher\nfast\bin>cspcheck.exe
cspcheck: fatal error: File key_mscapi_container-1c44b9424a23f6cddc91e8a065241a0
9aa719e4f (key #1): 0 modules contain the counter (NVRAM file ID 021c44b9424a23f
6cddc91)
cspcheck: information: 2 containers and 2 keys found.
cspcheck: fatal error occurred.
If I perform the same command on the original server (the server with the original kmdata folder and with the running RootCA services):
E:\nfast\bin>cspcheck.exe
cspcheck: information: 2 containers and 2 keys found.
cspcheck: everything seems to be in order.
Strange?
Moreover, when I do a csptest.exe command (also on both servers, i find this)
On the new server:
C:\Program Files (x86)\nCipher\nfast\bin>csptest.exe
nCipher CSP test software
=========================
Found the nCipher domestic CSP named 'nCipher Enhanced Cryptographic Provider'
Provider name: nCipher Enhanced Cryptographic Provider
Version number: 1.48
User key containers:
Container 'csptest.exe' has no stored keys.
Container 'Administrator' has no stored keys.
Machine key containers:
Container '352dd28a-17cb-4c6f-b6e4-bf39bcf75db5' has a 2048-bit signature key.
Container 'ROOTCA' has no stored keys.
Container 'csptest.exe' has no stored keys.
While in the old server:
E:\nfast\bin>csptest.exe
nCipher CSP test software
=========================
Found the nCipher domestic CSP named 'nCipher Enhanced Cryptographic Provider'
Provider name: nCipher Enhanced Cryptographic Provider
Version number: 1.40
User key containers:
Container 'csptest.exe' has no stored keys.
Machine key containers:
Container '352dd28a-17cb-4c6f-b6e4-bf39bcf75db5' has a 2048-bit signature key.
Container 'ROOTCA' has a 2048-bit signature key.
Container 'csptest.exe' has no stored keys.
As you can see, the container called ROOTCA, which is the one that I use during the installation, says it has no stored keys. While on the old server, it says it contains a key. Why is this happening? I dont know, I am copying the complete
key management folder from one server to another and initialize the security world with that folder as I always do, and i dont have any errors during this procedure.
Do you know what could be the cause of this? or how can I fix this? Thanks a lot, best regards.
Alejandro Lozano Villanueva -
MiniSAP WAS 6.10 and JAVA 1.4.1 (SUSE Linux 9.0)
Hello all!
I have some problems with the MiniSAP installation under
SUSE Linux 9.0.
I use the MiniSAP WAS 6.10, SAP DB 7.3 and the SAP Gui for the JE 6.10.
The Problem comes with the Java 1.4.1. In the documentation from the SAP CDs is the version IBMJava2-JRE-1.3-45 required.
If I try to run the SapGui i get many errors from Java (I think).
Anybody has a idea ?
Regards
René
e-mail: [email protected]Hello René,
I think you should download the latest SAP GUI for JAVA at: ftp://ftp.sap.com/pub/sapgui/java/630r4/PlatinGUI-Linux-630r4.jar
Regards
Gregor -
After downlaoding the lastest software for my iphone, it could not be activated because the phone was showing "No Service". Please want else can i do?
Thank you ProjectVRD. But this has not soloved the problem. It still shows no service even with my sim card well inserted. Even tried using sim card of another service provider thinking the problem could be from the service provider, it wasnt working still. PLEASE APPLE HELP ME.................
-
hi i have purchased iphone4 from vodafone australia 2 years back.it is unlocked, when i went to india .it was not working with any carrier in india.it was displaying no service.is it a problem of iphone or any other anybody please could let me know?
Hi ashish,
Did you contact TPG about activating International Roaming before you left for India:
http://www.tpg.com.au/support/international_roaming.php
Cheers,
GB -
my iphone 3gs said it was out of service then it turned off and when it turned on it said to activated then it said to plug in to itunes i did that n it turns back off. how can i fix it?? or whats wrong
If it continues to show the connect to iTunes graphic, then you do have to restore the phone. If you have not created a backup of your phone, then I hope you use icould because this will erase all of the info on the phone.
-
Pre-checks for cluster services setup
Hi Expert,
During the pre-checks for cluster services setup, I have got this error for Checking node connectivity.. How can I resolve this problem. The error is as follow as I enter "runcluvfy.sh stage -pre crsinst -n db-a,db-b" command. If the Check node connectivity fail, can I proceed to install the clusterware?
Checking node connectivity...
Node connectivity check passed for subnet "10.251.246.0" with node(s) db-b,db-a.
Node connectivity check passed for subnet "10.10.10.0" with node(s) db-b,db-a.
Node connectivity check passed for subnet "172.16.1.0" with node(s) db-b,db-a.
Node connectivity check passed for subnet "172.16.0.128" with node(s) db-b,db-a.
Node connectivity check passed for subnet "172.16.193.0" with node(s) db-b,db-a.
Suitable interfaces for the private interconnect on subnet "10.251.246.0":
db-b bge0:10.251.246.83 bge0:10.251.246.63
db-a bge0:10.251.246.82 bge0:10.251.246.61 bge0:10.251.246.99
Suitable interfaces for the private interconnect on subnet "10.251.246.0":
db-b ce0:10.251.246.64
db-a ce0:10.251.246.62
Suitable interfaces for the private interconnect on subnet "10.10.10.0":
db-b bge1:10.10.10.83
db-a bge1:10.10.10.82
Suitable interfaces for the private interconnect on subnet "172.16.1.0":
db-b ce3:172.16.1.2
db-a ce3:172.16.1.1
Suitable interfaces for the private interconnect on subnet "172.16.0.128":
db-b bge3:172.16.0.130
db-a bge3:172.16.0.129
Suitable interfaces for the private interconnect on subnet "172.16.193.0":
db-b clprivnet0:172.16.193.2
db-a clprivnet0:172.16.193.1
ERROR:
Could not find a suitable set of interfaces for VIPs.
Node connectivity check failed.
Thanks,
PegMost probably the virtual ip's are not virtual but connected to a physical device.
cu
Andreas -
Mobile Concierge Service Setup Guide
Hi All,
as with my previous is am starting this thread as a help in configuring the Mobile Concierge Service.
As the solution is new the documentation is a little light in detail so this is obviously a good place to document in more detail the setup and configuration.
What is neede for the Mobile Concierge Service:
Cisco Wireless LAN Controller:software version 7.2 or later
Cisco Prime Infrastructure: software version 1.3 or later
Cisco MSE (virtual or physical appliance): Cisco MSE software version 7.4 or later
Documents i have used:
Release Notes for Cisco Prime Infrastructure, Release 1.3.0.20
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.3/release/notes/cpi_rn_13.html
Cisco Prime Infrastructure Configuration Guide, Release 1.3
http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.3/configuration/guide/pi_13_cg.html
Cisco Location Analytics Service Configuraion Guide, Release 7.4.100.0
http://www.cisco.com/en/US/docs/wireless/mse/3350/7.4/Location_Analytics_Service/Guide/Cisco_Location_Analytics_Service_Configuration_Guide.html
Cisco Context-Aware Service Configuration Guide, Release 7.4
http://www.cisco.com/en/US/docs/wireless/mse/3350/7.4/CAS_Configuration/Guide/7_4_MSE_CAS.html
Connected Mobile Experiences Design and Implementation Guide Cisco Mobility Services Engine
http://www.cisco.com/en/US/prod/collateral/wireless/ps9733/ps9742/guide_c07-726506.html
As i attempt to get this service setup and configured i will post back here the details.
If anyone has any questions to get the ball rolling then pelase post here:
Mark Julier
@MarkJulierMobile Concierge - Venue Wizard
So the first thing that the Concierge service gets you to create is a venue. You do this by using the wizard.
Cisco's instructions are here:
http://www.cisco.com/en/US/docs/wireless/mse/3350/7.4/CAS_Configuration/Guide/7_4_MSE_CAS_chapter_0111.html#task_9F749496598541169607E266505012F4
Venue Name
So this will be the venue/location what you want this service to run at. For example if this is a Shopping Centre/Mall, Sports venue then you would give it the name of your Venue. e.g Dolphin Shopping Mall or BlackCats Stadium (made up names :-) )
As i am seting up this in our offices for testing i have given it the name of our company.
Floor outdoor/Association
Area Type - Next you choose area type either a floor area or outdoor. I have chosen floor area as i am looking to use this service internally.
Campus - Select that campus that you created in PI and want this service to work with.
Building - Select the building that you created in PI and you want this service to work with.
Floor - Select the Floor that you created in PI and you want this service to work with.
Coverage area - Select the Coverage area that you created in PI and you want this service to work with.
Selected Map - Once you have selected the coverage area above the map URL should be displayed here.
Click Next takes you to the next section.
Audio
Here you can select the audio that you wish touse for notifications and you can add up to three.
The manual does not explain what format these need to be in so PLEASE CAN SOMEONE ANSWER THIS PELASE
Am guessing that this is the audio that is played on the mobile device for a notification but this needs clarification.
Icons
Again the manaual does not explain the use of icons, PLEASE CAN SOMEONE EXPLAIN THE USE OF ICONS, WHAT FORMAT,SIZE ETC TO USE.
Am guessing that it is the icon that is displayed on the mobile device as part of MSAP (Mobile Services Advertismanet Protocol) but i am just guessing.
Venue APPs
Again the manual does not explain how this is actually implemented. I expect that this is how you specify through MSAP the APP's that are available at your location.
You enter the name of your app and i guess this is the actual name that appears on the mobile device.
You have the following options:
Web APP
Windows Phone OS
Android
BBOS
IOS
Symbian
WebOS
Windows Mobile
Desktop OS
Other
Am guessing that if you enter a URL in the first field (THAT HAS NO LABLE!!!) and select Web APP, that it will launch this URL in a browser on the mobile device.
Or if you have an APP that is installed on the mobile device you can launch it by specifing the APP name in a special format???
Again though i am just guessing so PLEASE CAN SOMEONE CLARIFY THIS PLEASE
Additonal Information
I think the next information is for Meriden who are Cisco's partner for mobile APP development.
Enter the location detail in the Location Detail text box. This provides details such as store address, zip code, or street address of the venue.
Enter the GPS latitude and longitude of the venue in the Latitude and Longitude text box. This helps the applications to identify the venue accurately.
Enter any other additional information that the venue would like to provide to the mobile application in the Additional Information text box.
Once you click save the information is applied in MSE.
So that is the first step in setting up the Mobile Concierge Service. What i would also like to know is that when you create a venue you ahve to specify a floor plan. So does this mean that if you have multiple floors that you have to create multiple venues? Or does it only work for one floor at the moment?
So over to the experts, can you ANSWER THE MAIN POINTS THAT ARE IN CAPITAL LETTERS ABOVE. I have put them in capital so that they stand out from all of the text.
Thanks
mark Julier
@markJulier -
When I try to activate iMessage and while I write my correct password I I receive message say that my user name and password is incorrect although I was use iMessage service on the same network (etisalat ) U.A.E before I update to ios6
Note : my iPhone is been swapped 2 weeks ago and I already erase all data in old I phone1) Go here: http://www.apple.com/support/appleid/manage/
2) Click on Sign in to manage your Apple ID
3) Click on Manage your Apple ID
4) Type in your Apple ID and Password and click Sign in
5) Select Addresses from the left hand side
6) Click Edit
7) In country region type United Kingdom
8) Click Save at the bottom of the page
9) Go to your Apple Device Settings - General - International - Region Format - Select United Kingdom
10) Press the Home button
11) Log into Facetime and iMessage with your CORRECT APPLE ID AND PASSWORD
This should work for all of you guys. Hope it helps. -
Where do I find the Integration Services Setup Disk?
When I connect to my VM and select Insert Integration Services Setup Disk from the Action menu, nothing happens. Should this be on my my Windows Server 2008 R2 DVD that I used to set yp Hyper-V and my two VMs?
ThanksAgain, the Integration Services are ONLY for installation inside a virtual machine. You aren't gonig to see an option for them unless you're connected to a VM via the Hyper-V management console (the option is under the Action menu.)
Windows 7 includes the Hyper-V integration components, you may need to upgrade them depending on what service pack levels your Win7 and Hyper-V server are on.
However, the legacy adapter and integration components aren't dependent upon each other.
The legacy adapter would be added to your VM before you install an OS in your VM and IC are installed after you finish installing your OS. With Windows7 you don't need to use the legacy adapter since Windows 7 is a supported OS and Integration
components are available.
Also, are you trying to add the legacy adapter while the Windows 7 VM is running or in a saved state? If so, that is the reason it isn't available to install, the VM needs to be powered off.
Maybe you are looking for
-
Sender Adapter Module Not Working
Hi, I have changed an existing Sender Adapter Module code and deployed using SDM. It was working fine but after some days it is not working as designed. Say for an example, the number of pipes(|) in each record is one less than usual number of pipes.
-
24P Playback and Project settings
I'm a Final Cut guy switching to Premiere Pro CS5.5 and have legacy files to edit. I"m trying to figure out the best project settings (Mac Based) Bringing in Pro Res files 1920 x 1080, 24p. I have a Black Magic Decklink Studio with most current dr
-
I wish to finalise purchase and download order No. AD005601414Au James Wishart
I need an answer to the above.
-
I have contacted Report A Problem about getting refunds from apps that don't work and I haven't received those refunds yet.
-
No Exception Defined for System Errors
hi, I am capturing system messages through an Exception error handler in the block step of Integration Processes. Its a IDOC -> XI -> HTTP Receiver scenario. When i execute the scenario, i see an error in the workflow in the Block Step. It shows an E