Minor Alret at prime infrastructure 2.0 about mismatch configuration.

Dears,
kindly i have minor Alert at prime infrastructure 2.0 (Audit done at '2013-nov-28,05:00:00 CET'..config difference found between NCS and Controller),
what this error and please feed me back with steps to solve this problem.
Thanks,

Hi Ahmed,
adding to Scott:
Login in Prime Infra.
First check your theme(Classic or Lifecycle).......Go to Root and see the Theme.
There are steps for classic theme
Go to Configure> Controllers
and then which controller have config mismatch...on right side click on mismatch in Audit status tab.
After that it will ask for audit now, click on that. After auditing it will show you the two option:
1. Restore PI values to Controller
2. Refresh config from controler
Clcik on 2nd #Refresh config from controler#
Then select 2nd option again(Use the configuration on the controller currently) and click on GO.
Regards
Dont forget to rate helpful posts

Similar Messages

  • Prime Infrastructure 1.3. No 'Configure' Menu??

    Hi all,
    We're migrating from Cisco WCS 7.0 to Prime Infrastructure 1.3. We have the server up, and the web interface all set, however, a rather large issue is there's no longer a "Configure" menu, and we can't add our wireless controllers in because all of the documentation says to do "Configure -> Add Controller".
    I already verified that my user accound has admin rights, and therefore access to that menu in the user settings.
    Am I missing something extremely obvious? Thank you much,
    Jim

    Try changing your menus from classic to life cycle view. The selection is done under your user login name on the top right.
    Sent from Cisco Technical Support iPad App

  • Prime Infrastructure 2.1 - Fetch VLAN Configuration - command failed

    Hi,
    i am installing the system on a customer's site.
    i've noticed that most of the devices configured on the PI have resulted in error in the Configuration Archive with this error:
    Fetch VLAN Configuration - command failed.
    i checked that the tftp service on the PI is enabled.
    i tried manually executing from a device: copy flash:vlan.dat tftp://PI_IP and couldnt manage to do so.
    i also tried manually to do it to another tftp server and it worked.
    i dont see any FW drops.
    does anyone have any idea how to troubleshoot this?
    thanks in advance!

    As to get the VLAN information, the file in Cisco devices Flash : Vlan.dat is fetced, and if PI fails to do so, it gives this error. As it is a file in flash, PI needs to send it over to Server itself using TFTP.
    If TFPT is somehow not working between Server and devices, it may throw this error.
    Is it happening with all the devices or some perticular platform?
    If with all the device, you need to check if there is any Firewall blocking TFTP access to devices.
    Also, you can check if TFTP service on CPI is working properly by command ncs status.
    If service is affected, try to restart service - service tftp restart Or you can restart the PI Machine itself.
    -Thanks
    Vinod
    **Encourage Contributors. RATE Them.**

  • Prime Infrastructure 2.1 switch in stack down alert

    Hi all,
    Have a question regarding the Cisco Prime Infrastructure 2.1  - How to configure the prime to monitor/send an alert when one of the switches (c3750) from a stack goes down (not the master, so the stack appears as 'up' ) ?
    In old cisco LMS i was able to configured a script based on a syslog sent from a switch, but I'm not sure how to do it in Prime.
    Thanks for help :]
    Pawel

    Pawel,
    Unfortunately PI 2.1 (and 2.2) do not yet allow us to define automated actions in the event of a specific syslog message being received.

  • Cisco Prime Infrastructure release 2.1 configuration archiving on CISCO WiSM2

    Hi all,
    Just wondering Cisco Prime Infrastructure  release 2-1 support configuration archiving on CISCO WiSM2?
    CISCO  release 2.0 mentioned that it doesn't support configuration archiving for WiSM2 but release 2.1 doesn't mention anything on it.
    Please assist.

    No, it is not supported even for PI 2.1

  • Upgrade questions about Prime Infrastructure 1.1.1.24 to 1.3

                   My existing NCS is installed with the small deployment and I'll have a total of 94 AP's but we are installing a new data center and replacing the existing 2 WISM blades for 2 new 5508 WLCs and added 20 more AP'S which will total 114 AP's and 4 controllers. The old WISMs blades and new 5508s will be up together until we migrate exisitng AP's to the new 5508s, so do I need to install the medium deployment since Table for Scaling Prime Infrastructure states:
    Medium: 500 Total. The mix of devices may included up to:
         Wired devices: 300
         Controllers: 5
         Autonomous AP's: 300
         Unified AP's: 300
    Small Deployments are for a total of 250 devices "with up to" 100 Unified AP's and 2 controllers?? 
    Also as part of the download of software for PI 1.3 it   includes Automated Deployment Gateway is this a required piece to install for PI??  We don't use Cisco works so I'm not installing the LMS piece. 
    thank you,
    Sandra

    Isn't it rediculous the message says:::
    Error(s): You must correct the following error(s) before proceeding:
    Error:Unknown Exception Occurred. If the problem persists send logs to Tech Support.
    And the fix is to use a different browser?
    BTW:: Good Idea to try a different browser.  By the looks of the Error Msg, it just didn't look like a browser issue to me so I didn't think to do that but certainly will next time on this and probably many, many, many other issues I see-
    We only spent about an hour chasing our tails around to see what the issue was.
    Again good catch!
    I was speaking w/ another customer today who mentioned if the application were re-written to use HTML 5 these type problems would go away.
    Oh well.
    Glad I could help you get all the way upgraded and all the way up and running and able to push templates to your lightweight APs.
    Cya

  • Some question about Cisco Prime Infrastructure

    Dear all
    I have some question about using Cisco prime Infrastructure:
    - Can I show how many user access to one Access Point (AP) ?
    - If I can. What is display information of user ? etc Ip address, MAC, username access, name of device (notebook, tablet, phone ..)
    - How many time do Cisco Prime Infrastructure refesh user  informantion .?
    Please help me and send picture about it if you can.
    Thank you so much.

    Hi,
    I don't have the Prime Infrastructure to post you image, but you can simply find all the answers you want on the config guide:
    http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.2/configuration/guide/clientmgmt.html#wp1232242
    1- You can surely find how many clients associated to a specific AP.
    - Informaiton of the client usually includes username, SSID, ip address, mac address, RSSI, device vendor...etc. I don't think it contains the device type (ipad or iphone both appear as apple vendor. it does not destinguish between this and that.
    3- The time of the refreshment is configurable. You need to configure the corresponding background task for the poll period. (this is also metnioned in the link above).
    HTH
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • Prime Infrastructure 2.1 - getting informations from Nexus7Ks about ip to mac to physical pot table

    Hello,
    does anybody know if there's a way to get the following informations out of nexus 7000 and nexus 5000/2000 switches?
    Environment/requirements:
    - snmp v3 has to be used
    - N7ks are configured with several vrfs
    - SW N7K: 6.2.8a
    - SW N5K: 6.0(2)N2(4)
    - Prime Infrastructure 2.1
    I want to see under Clients and Users entries about mac-address, ip-address, interface and vlan.
    At the moment, I only get informations from N5Ks/N2Ks without ip-addresses. From the N7ks I don't get any informations.
    Any hints or tricks, how to get these informations with PI2.1 out of the nexus boxes?
    best regards
    Markus

    Hi Andy,
    Check the below link , as per this Doc .. User tracking is supported in 2.0:
    http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
    Thanks-
    Afroz
    [Do rate the usefu post]

  • Migrating from NCS 1.0 to Prime Infrastructure 1.2

    Hi friends
    I know i had short discussion about this before but here it comes again and this time in detail.
    I have NCS 1.0 with 100 devices support license installed. Now knowing it has reached end of sale, and also for the fact that Prime does cover devices like routers, i went ahead to the upgrade path via PUT (Product Upgrade Tool).
    Finally I received an email (OBA) advising my order is ready. This email included two items in the shipment,
    L-N-PI12-100-M=
    NCS 1.0 to Prime Infrastructure 1.2 Minor Upg 100 Device
    L-PILMS42-100-M
    Prime Infrastructure LMS 4.2 - 100 Device Upgrade Lic
    When i click to the link in the same email to download the license, it only shows me one file which is
    L-PILMS42-100-M
    I tried using this file and installing on the NCS1.0 but it gives me error that this file is not a license file. The license name suggests me that it is not the license to be installed on the NCS. The file should be L-N-PI12-100-M=
    Thanks for reading this all and would appreciate all your inputs here.
    Regards,
    Mohit

    Marvin Rhoads wrote:Your PI 1.2 also includes the right to install and use LMS 4.2 - a separately installed and licensed server.If you want Assurance (or Compliance) licenses for PI, they will have to be ordered separately. The license files delivedred when you buy those product SKUs will allow you to use those features. The starting point (base) in PI 1.2 is Lifecycle.
    when i followed the inpath upgrade,  i receved an email from the licensing that the license file is ready for download. the order said,
      Product Name          : L-PILMS42-100-M
         Product Description      : L-PILMS42-100-M : Prime Infrastructure LMS 4.2 - 100 Device Upgrade Lic     
    and the attached lic file "LMS2013021XXXXXXX.lic" came along from them.
    but when i installed that lic file, i got the error message from the upgarded the PI 1.2 that the file is not a license file.
    The trouble is i cannot generate another lic file (if the exsting generated file was corrupt) cos the PAK is already been used once. 
    Now i am wondering i can avail that LMS file that would be good, but when i spoke to the TAC, i was told that this file name doesnt seem correct as this is PI and it wont understand LMS file. It was only useful if you were upgraing from LMS to PI and because my case was NCS to PI, this will not work.
    Any suggestions?

  • Prime LMS EOL? Migration to Prime Infrastructure???

    Hi All,
    I'm a little bit confused about the support for Prime LMS 4.2.5... is there any date for end of Life/end of support for LMS?
    Should customers migrate to Prime Infrastructure or what does cisco recommend???
    best regards

    Prime LMS 4.2 is not yet End of Sales or End of Life. Cisco continues to provide support develop minor device package updates etc. for it.
    It will not get another major release going forward as strategically the platform being developed for wired and wireless LAN management is Prime Infrastructure (PI).
    For existing LMS customers, they are encouraged to review the current feature comparison (link) and determine which product better serves their needs given that PI 2.2 does not have feature parity with Prime LMS 4.2.5. (Even new PI customers are given a license for Prime LMS in acknowledgement of this fact. How long that continues remains to be seen.)

  • Ask the Expert: One Management with Prime Infrastructure 1.2

    With Tejas Shah
    Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions from Cisco expert Tejas Shah on One Management with Prime Infrastructure 1.2 Combining the wireless functionality of Cisco Prime Network Control System (NCS) with the wired functionality of Cisco Prime LAN Management Solution (LMS),  Cisco Prime Infrastructure simplifies and automates many of the day-to-day tasks associated with maintaining and managing the end-to-end network infrastructure from a single pane of glass. The new converged solution delivers all of the existing wireless capabilities for RF management, user access visibility, reporting, and troubleshooting along with wired lifecycle functions such as discovery, inventory, configuration and image management, automated deployment, compliance reporting, integrated best practices, and reporting.
    Tejas Shah is a senior technical marketing engineer for Cisco Prime Infrastructure and Collaboration products. He has deployed Cisco Prime Collaboration Manager at various customer sites to help customers monitor and troubleshoot their video infrastructure. In addition, he is part of the Network Operations Center team at Cisco Live events for six years. Shah joined Cisco in 1995 and was in the Technical Assistance Center team supporting various network management system products for more than six years.
    Remember to use the rating system to let Tejas know if you have received an adequate response. 
    Tejas might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the Wireless Mobility sub-community discussion forum shortly after the event. This event lasts through Sept 21, 2012. Visit this forum often to view responses to your questions and the questions of other community members.

    Raun, please see my responses inline:
    Can you go over the licensing method with Prime Infrastructure 1.2 please? 
    Raun, you can check out the following link for ordering guide at
    http://www.cisco.com/en/US/products/ps12239/products_data_sheets_list.html
    I currently have NCS and do NOT currently have LMS.  I know I can move to Prime Infrastructure through Cisco Product Upgrade Tool.  However, what I am confused about is do I still have to buy LMS to have LMS functionality in Prime Infrastructure 1.2? 
    ==> Not at all.  The converged product will give you basic management capability for routers and switches that LMS provided in this release.   Feature/Functionality will keep on growing with upcoming releases.
    If not, do the licenses I transfer into Prime Infrastructure 1.2 from NCS also work for devices to work under LMS? 
    ==> Licensing is different than NCS or LMS.  You don't have to transfer the license.  Each install of Prime Infrastructure will have a unique UID string on which the licenses are based.  A new license will be applied to the product.
    Mean, can my currently 350 licenses be used for AP's as in NCS and routers in the LMS portion of Prime Infrastructure 1.2?
    ==> I would recommend getting a total count of your wired and wireless devices and match the right SKU based on that.
    Hope this helps.. Let me know if you have any further questions,
    Tejas

  • Does Prime Infrastructure 2.0 support 7.5 code?

    I am currently running PI 1.3 and plan on upgrading to PI 2.0. Are 5508 Wireless Controllers 7.5 and MSE 7.5 code supported in release PI 2.0?

    PI 2.0 was really intended for the converged access, but it will also support v7.5 and PI1.4 supported v7.5.
    Management Support for WLC Release 7.5
    Prime Infrastructure 1.4 provides management support for WLC Release 7.5 and associated features. In addition, this release provides support for AP platforms such as 3600P and 802.11ac module.
    For more information about Cisco Unified Wireless Network (CUWN) Software Release 7.5, see the product bulletin at the following URL:
    http://www.cisco.com/en/US/products/hw/modules/ps2797/prod_bulletins_list.html
    For more information about the features of WLC Release 7.5, read the Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 7.5 available at the following URL:
    http://www.cisco.com/en/US/products/ps10315/prod_release_notes_list.html

  • When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?

                       We are running Prime Infrastructure 1.3 primarily for wireless management at this point.  We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out.  While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features.  For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers.  I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment.  Does anyone know when it's officially being released?  Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are?  I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management.  Any useful information or links would be appreciated.
    Thanks,
    Christian

    PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
    I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
    For what does it have for customers?
    > As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
    As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
    With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
    -Thanks

  • Prime Infrastructure 2.0 Job Approval notifications?

    I have a question about notification for job approvers in Prime 2.0.  I'm trying to setup PI such that a restricted user can create a configuration change on a wireless controller and submit it for approval by the PI admin.
    The PI admin will likely not be logging in every day to check job approval status.   I can't see anywhere that notifies the admin via email that a job is waiting.  can this be done or am I missing something?
    -Tim

    Hi Tim,
    I don't think we have an email optiom to notify the ADMIN to approve the pending jobs ,however if you authorized any job then ONLY admin can approve to run the job.
    check the below link:
    http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/administrator/guide/config_server_settings.html#wp1081686
    Thanks-
    Afroz
    [Do rate the useful post]

  • Prime Infrastructure 2.0 Automatically add remove devices

    Dears,
    I'm basically looking for a dcrcli equivalent to use on prime infrastructure 2.0.
    Customer has a central repository of devices that must be monitored. When devices are added or removed there, they automagically appear or disappear in the other systems.
    Does something like this exist or is this on the roadmap?
    Cheers,
    Michel

    Hi Scott,
    Upto 7.3 config guide it was documented we have to reboot WLC when we configuring SNMP v3 which is wrong. (here is 7.3 config guide link for reference). May be older version (prior to 7.0) had that requirement, not too sure about it
    http://www.cisco.com/en/US/docs/wireless/controller/7.3/configuration/guide/b_wlc-cg_chapter_0100.html#d16741e4514a1635
    From 7.4 onwards config guide does not talk about it all. I deleted the default SNMPv3 user & create a new user in 7.4 & add it to prime without rebooting WLC.
    Once you configureed a SNMPv3 user on a WLC, I do no think you can edit/change the password. You have to delete the user & recreate it with modified username/password.Then re-add the WLC to prime
    The behaviour you mentioned is with any of later codes  of WLC ?
    Rasika

Maybe you are looking for