MIO software error on cdaq 9188 / NI 9477

Hi,
Im using cdaq 9188 controller and 7 different io modules like.
1: NI 9426
2: N I9477
3: NI 9205
4: NI 9264
5: NI 9485
6: NI 9211
7: NI 9222
When i run for Digital output using daqmx create channel.vi , and write digital channel i set TRUE as auto start task.
here i am getting error as:
Error code = -225202
Error description = Internal softwware occurred in MIO software. Please contact national Instruments support.
What could be the reason, please suggest me:
Regards,
Balaji DP

Check the firmware version of your 9188. Mine was shipped with 1.1.0f0; upgrading to 1.5.1f0 fixed my MIO software error.
New firmware here: http://www.ni.com/download/ni-cdaq-9188-firmware-1.5.1/4302/en/

Similar Messages

When configuring my cDAQ 9188 Ethernet chassis, error 88705 was encountered

Hi,
I'm configuring my cDAQ-9188 Ethernet chassis and I have encountered an error: Error-88705, when configuring the board using NI MAX. On my pc running on Windows 8.1 and using having 2 network cards, I have installed LabVIEW 2014 and than NI-DAQmx9.9 which was upgraded to 14.5. I tried to communicate with the board using both DHCP and static IP but this error still persisted. Furthermore, I've re-installed the NI-DAQmx a couple of time since one of the suggestions was that it might be a software problem. However, the TCP connection is established correctly in both cases (when using static IP or not) since when I'm able to configure the board through NI Network Browser and it works perfectly. Still, through LabVIEW I cannot access the board via the DAQ assist. Moreover, the NI-loader settings were changed according to http://digital.ni.com/public.nsf/allkb/0819391CA91B3EB38625731D00024649?OpenDocument and the fire was switched off. Kindly find attached relevant screenshots. Do you have any suggestions, please?
Thanks in advance.
Best Regards
Joseph
Attachments:
NI_MAX_reserve_chassis.png ‏54 KB
NI_MAX_selftest.png ‏51 KB
NI_network_browser.png ‏62 KB

Thanks, but still I did not solve the issue. I have implemented the improvements show in the table below without any success. As shown in the screenshot the error is still encounter
Improvement
Link
Result
2 port configuration
http://digital.ni.com/public.nsf/allkb/AC929F0881D9178A862578B000586491
Error 88705
NI Device Loader
http://digital.ni.com/public.nsf/allkb/0819391CA91B3EB38625731D00024649
Running /Updated but error 88705 still unsolved
NI mDNS Resp Ser
Running /Updated but error 88705 still unsolved
NI Configuration Manager Service
http://forums.ni.com/t5/Multifunction-DAQ/NI-USB6211-Error-88705/m-p/2371998/highlight/true#M76206
Running /Updated but error 88705 still unsolved
Resetting MAX Database
http://digital.ni.com/public.nsf/allkb/2C7480E856987FFF862573AE005AB0D9
Error 88705
Firewall off
Error 88705
Attachments:
5_Static IP.png ‏304 KB

No reconoce cDAQ-9188 via ethernet

Hola Amigos
Tengo el problema de que en Measurement & Automation, me reconoce el chasis cDAQ-9188, pero no sus modulos he intentado todo lo que se recomienda en esta sesion http://digital.ni.com/public.nsf/allkb/DF65FCF0DD20D71686257949007ECAA7 pero no obtengo resultados positivos, alguien podria orientarme...
Lo agradeceria muchisimo
PD: Adjunto lo que me aparece
Solved!
Go to Solution.
Attachments:
error_1.png ‏255 KB
error_2.png ‏184 KB

Hi pomontty,
Networked cDAQ systems require host reservation, to avoid conflicts where multiple hosts on the network might try to access the modules at the same time. For that reason, you do not have access to your modules until you have selected Reserve Chassis from the top of the MAX window or from the right-click menu on your device in the Network Devices tree. You also cannot self-test or reset the chassis when you have not reserved it, which is why you see the error you've attached.
Kyle B | Product Support Engineer | ni.com/support

TS1814 Io ho windows 8 e non riesco a aggiornare il mio software di iphone 4s

Io ho windows 8 e non riesco a aggiornare il mio software di iphone 4s e ho bisogno di aiuto.

dedak71 wrote:
I bought an HP pc with windows 8, download latest version of itunes but it does not work connecting to my iphone 5!! Do not download anything! What to do?? (Google Translate)
Do one or more of the following:
> Restart your computer
> Uninstall & Reinstall iTunes
> Reset your iPhone (will not erase anything)
> Go to My Computer (Windows XP) go to Computer (Windows Vista & 7) and see if your iPhone shows
> Restore the iPhone (will erase everything)
Did you received any errors when plugging your iPhone?

SignalExpress 2012 does not recognize cDAQ-9188

How can I setup SignalExpress to communicate with the cDAQ-9188 module? I found the system in MAX but I can see no device connected in the Channel View.

Hi Runner,
I saw there is nothing in your channel view, could you please check the version of your NI-DAQmx driver from Control Panel>>Uninstall a program>>National Instruments Software?
Here is my channel view:
And here is the version of NI-DAQmx:
You can download the latest DAQmx driver here: http://sine.ni.com/psp/app/doc/p/id/psp-268

Internal Software error PGC for encore CS3 !!! solved !!!

Almost everybody here knows the next error:
PGC "timeline name" has an error at xx:xx:xx:xy internal software error : %0, line timeline name - PGCINFO: name= timeline name, ref=BPGC, time=xx:xx:xx:xy
Where the y in time stands for the length of the timeline minus 2 frames. The BPGC error can also be FPGC or DPGC dependant on how many menu's there are in the project.
It kept me awake for weeks and after reading this forum several times and comparing encore CS3 with encore 2.0 filenames I found the solution.
This Error is a bug in encore witch has nothing to do with blank filename spots and sonic coding or codecs or planning your workflow with a pencil but pure with the combination Adobe Premiere Pro CS3 and Encore CS3.
This is what generates the problem:
In Adobe Premiere Pro CS3 you build project with video, sound and chapters. Then you export the project via the Media Encoder not Multplexed.
Premiere CS3 then creates the following files:
filename.M2V (video file mpg)
filename.AC3 (audio file ac3)
filename.M2V.XMPSES (an adobe file with preview info and chapter pointers)
filname.XMP (??)
It is the .M2V.XMPSES file witch creates the PGC error. If you use the MULTIPLEX DVD option then ADOBE will not create the .M2V.XMPSES file so there will not be an error. This trick mentioned by ADOBE and many others is just to go around the bug instead of solving it. Also with multiplex you have just one sound track. I use two sound tracks like 5.1 and a 2.0 track witch you can choose in a menu.
Some people say it is the blank spots. Also not true. They have probably just erased the blank spots of the M2V file and forgot the .M2V.XMPSES file.
When you just delete the .M2V.XMPSES file and then open the M2V and AC3 file in Encore as a new asset, make a timeline and menu's and the project will built and burn. Only if you delete this .M2V.XMPSES file Encore takes a longer time to import the M2V file and will be without the chapter points.
Almost everything else will work like menu with sound and even a movie background (use M2V files). Only the motion buttons in a menu still wont work unless you use a black background !?!. Haven't figured this out yet. Only solution for this is use Encore 2.0. In this older version also the motion buttons will work without error's (everything else also so why buy CS3??)
Here is what you must do create a DVD without errors:
-Create a project in Premiere Pro, even with chapters.
-Write down all chapter points (minutes:seconds:frames)
-Create two new unique maps in explorer for example D:DVD1 and D:DVD2
-Export in Premiere with Media Encoder without the Multiplex:DVD but with NON to the D:DVD1 map
-Copy from D:DVD1 only the M2V and AC3 files to D:DVD2
-Start up Encore DVD CS3 or 2.0
-Create a new unique project in Encore for example "DVD" and save this in the map D:DVD2\
-Then use Save-as (under file) and pinpoint to D:DVD2\dvd to be sure that all Encore's files are placed in this folder.
-Select M2V file and make new timeline.
-Make chapter points (you wrote down the points, did you?)
-Create menu's, even with sound (AC3) and movie background (M2V)
-Then render project if you have used a video for menu background
-Finally Built and burnnnnnn!!
-If you like to use motion buttons in a menu then use Encore 2.0
I have double checked my work flow and it really works. I have built a project and burned with success Then I deleted the timeline and the M2V file. Copied the .M2V.XMPSES file in the used folder. Re loaded the M2V file in encore (this time much faster! and with chapter points). Tried to built and burn and back was the error. Also this happened in in Encore 2.0!!
Hope that this will solve the PGC error once and for all !!!
Marcel W
system:
acer aspire AMD 64 3800+
2 GB
250 GB hard drive for system
750 GB hard drive for movie
software Adobe Encore 3.0.1.008, Premiere PRO 3.2.0, Photoshop CS3 10.0, All upgraded
NERO 7
No Internet

> Where the y in time stands for the length of the timeline minus 2 frames.
This can actually vary, and so far at least, I don't think we've seen a pattern as to type of pgc error based on how many frames from the end it reports.
> The BPGC error can also be FPGC or DPGC dependant on how many menu's there are in the project.
Number of menus is not relevant; the iteration of the first letter is more related to subsequent occurrences of the error. In my current tests it did not always update; they may have been too similar.
> This is what generates the problem...
Well, the problem does not occur every time you do what you describe, any more than it occurs every time spaces are left in the file names. What you have is, as some other suggestions, a workaround. Thats not bad, and I wonder if you are onto something as to what is contributing to the problem.
So, on to the interesting part whether the xmpses file, or at least what Encore is doing with it, is contributing something. I took an old test project that throws the PGC error and did some experiments.
Background. I am a user who does get the pgc errors regularly, but not always. Creative Suite Production Premium, with PPro CS3 3.2.0 (374) and Encore 3.0.1.008. Pentium 4 2.8GHz 2G RAM, XP SP3, Multiple drives, Nvidia GEforce4 MX440 i.e. an older system. I have lots of stuff loaded and running, including virus protection and firewall, so there are any number of potential conflicts. But I get no crashes, and only one problem other than the pgc. (PPro and Encore monitor windows do this diagonal thing I suspect the display card, but the drivers are up to date. Maxing and then back to fit fixes it.)
If you want to attempt to replicate my studies, here is a link to my problem clip and the first Encore project I describe.
http://www.videoandcomputer.com/test/pgc_test.htm
This project involves a very short AVI export from PPro CS3 - just over 8 seconds - called pgcbad_clip1.avi. Just to answer any question, the source is dv camera capture, and the source and avi export I use are dv avi type 2. There were no effects added on the timeline.
Test 1: Create a project in Encore CS3. Use the sunset menu and delete all the buttons except "play all." Import the avi as a timeline. Set the timeline end action as "return to last menu" and set the button link to the timeline. Auto transcode. (Project settings are 8mbps max and a3c.) Check project shows okay; there is never a problem with that. Build to a DVD folder in a new folder. This project throws the pgc error.
Test 2: Now create a new Encore project in a new folder. Use the same process, except import as timeline the m2v and a3c files from the first run. (I.e. if the clip is pgcbad_clip1.avi, in the test1 project folders, there is a folder called pgcbad_clip1.avi that has 6 files.) Note that in the folder they are imported from is an xmpses file from the first project's encore transcode. The build again fails with the pgc error - same frame, etc, but I really think the frame number doesn't matter.
Test 3: Now create another new Encore project in a new folder. Use same process, but before importing the m2v and a3c as timeline, delete the xmpses file. Drumroll...... Build succeeds!
Go figure.
This is not the repeatable bug option weve been looking for, but based on a clip that always fails, it does demonstrate the odd event of deleting the xmpses file as a workaround. I wonder if that will give adobe something to work with.
Can anyone else get my clip to work/not work in a straight project?
Test 4: Just to answer the question since the avi file fails here, will the elemental option succeed? I exported elemental m2v and wav from PPro, used the same project process, and transcoded the wav. That build also works! I have seen this work both ways. I have had projects where the elemental failed, and an avi export worked. I do believe the elemental options work more consistently. But my project that I completed yesterday used all avi exports, animated buttons in the submenu, - no pgc error.

When I try to burn a DVD in Premiere Elements 12 I get an Internal software error%0, line %

When I try to burn a DVD in Premiere Elements 12, I get an Internal software error %0, line %1. This is the first time that I have tried to use this program.

As suggested in the original reply in January, you will find best advice over on the video forum. Most of us here are photographers.
Click on the link below and copy and paste your question again. Good luck.
Video questions: Click here for Premiere Elements Forum

Hard Drive Short DST Check: Software Error

Hard Drive Short DST Check: Software Error appears while performing Hardrive Test in HP ENVY Sleekbook 6-1090ee. Please advice on how to resolve this error

Same issue here. Only I've tride a brand new hard drive and get the same results. Within seconds of power on, it shuts off hard. Sometimes the backlight comes on and it gets to the HP logo, then bam - out go the lights! I can go into the BIOS and stay there a long time. I run all the diags and make changes. Once, it actually stayed on and booted up. I downloaded the latest BIOS update, flashed it, and rebooted. It didn't help. Also, tried to boot to a bootable Windows 8 thumb drive. Same results, shuts down after 3 seconds. Tried many times to boot to external USB CD/DVD drive, never succeeded. The only error any diag reported was Hard Drive Optimized DST Check: Software Error. The fan spins at almost top speed but not immediately; it takes about two seconds after power on for it to start. I don't know, but that seems to be a clue. The only time I had a successful boot, the fan didn't engage at top speed, but a few notches slower.

How do you get Encore to work? Internal software error.

I've made a new project with Encore CS4 consisting of mainly slideshows and about 2 movie timelines. I've created menus to be how i want them.
When i go to build the project about 9/10 it doesn;t work. Sometimes it just crashes and gives a crash report. other times it does all the building slideshows and motion menus then starts the prepare build and comes up with internal software error, and build stops.
This is extremely frustrating as it takes serveral hours to get to this stage every time because it has to re build all the slideshows.
It has only worked once, and it wasn;t quite what i wanted so i made some minor adjustments (added a pic in a slideshow, or music to a menu) and since have tried twice to rebuild it and it hasnt worked.
Encore seems like it could be really good but all its bugs make it a piece of crap.

I don't remember the dimensions, but I have read messages that pictures that are too large will cause problems... maybe someone will come along who knows the actual size and can tell you
Also... This is aimed a Premiere Pro, but may help
First, work through all of the steps here http://ppro.wikia.com/wiki/Troubleshooting
If your problem isn't fixed after you follow all of the steps, report back with the DETAILS asked for in the questions at the end of that link

An internal software error has occurred. Error code: 1003

Dear, I am working on a FPGA programming. When I use the VI: "High Throughput Add Function". Some error occur.
Internal software error(s):
Error code: 1003 (refer to details)
Details:
An internal software error has occurred. Please contact National Instruments technical support at ni.com/support with the following information:
Error 1003 occurred at E:\Program Files (x86)\National Instruments\LabVIEW 2012\vi.lib\rvi\FXPMathLib\FxpAdd\modGen\nifxpmath_Add_EmitCode.vi: There's a broken VI

Hello Yjin,
Can you show me a VI in which this error occurs?
Which software versions are you using?
An easy way to find this information is as follows:
http://digital.ni.com/public.nsf/allkb/271F252B4EF0A2E0862570E70056A1E4?OpenDocument
Kind Regards,
Thierry C - Applications Engineering Specialist Northern European Region - National Instruments
CLD, CTA
If someone helped you, let them know. Mark as solved and/or give a kudo.

Error -20023 internal software error

Hola a todos. Soy un nuevo usuario del labview y mientras intento aprender algo me he topado con un error que no entiendo a la salida de un filtro:
Software error ocurred in no asociated comand id on axis control error -20023 internal software error please contact ni for suppor
Lo que hace el programa no es problema. La cosa es que si quito el filtro funciona bien.
Para hacerlo funcionar utilizamos una señal simulada de una 9239 creada con MAX.
Si alguien puede darme alguna idea, se lo agradeceré un monton.
Attachments:
prueba3.vi ‏291 KB

Hola Gonzalo el código de error es de un filtro y el VI que estas utilizando para interpretar los errores no te da una descripción adecuada porque ese es para Motion, y en este caso no lo estas usando por eso la descripción del error no tiene sentido.
Aquí el erro puede ser por poner rangos inválidos en la frecuencia de muestre, o corte, o debido a que no hay información en el waveform. La siguiente liga tiene mas información:
http://digital.ni.com/public.nsf/allkb/ABBD3A7BC25E17C8862561270058A4A0?OpenDocument
Saludos
Benjamin C
Senior Systems Engineer // CLA // CLED // CTD

Internal Software Error occurred in MIG software DAQmx

Hi All, I have a very disturbing problem. Ever since upgrading to Labview 2011 and NIDAQ951f1 I get errors like the following in code that uses DAQmx:
Error -229771 occurred at DAQmx Create Channel (AO-Voltage-Basic).vi:1
Possible reason(s):
Internal Software Error occurred in MIG software. Please contact National Instruments Support.
The strangest thing is that this happen only when I run the VI while a LV project is open! It does not matter wether the VI is part of the project or not. As soon as I open any project (or create a new empty project) the error occurs when I run any DAQmx code. To test I am using one of the DAQmx example files: Cont Gen Voltage Wfm-Int Clk-On-Board Regeneration.vi for now, but the problem occurs with the other examples as well.
I tried to resolve the issue by removing all NI software and doing a clean install, but the problem persists. Needless to say I cannot do any development this way.
Any idea what's going on? Please advice.
Best regards,
Dixie

Hello Dixie,
There is a knowledge base topic treating this issue --> http://digital.ni.com/public.nsf/allkb/03123D0E8A36C48E862577A4005B6BAA?OpenDocument
Have you already had a look at it?
The problem you have can also be somewhere network-related. As some networking feature are handled by the Project Explorer, this can explain why you encounter the issue only when it is open. I propose that you first check the knowledge base and then keep me updated. I will give you further info if that does not solve the issue.
Cédric | NI Belgium

Internal Software Error in MIG

Running Windows XP SP 3
Labview 8.2
Error:
Error -229665 occurred at DAQmx Create Channel (DO-Digital Output).vi:1
Internal Software Error occurred in MIG software. Please contact National Instruments Support.
No new devices installed.
When opening MAX no devices listed in Device & Interface category. Same error with other VIs.

Did not work for me as the tool returns an error.
Instead I used MAX : Tool>>Reset Configuration Data after making sure I first exported all my configuration (devices, tasks, channels, scales...) as described here. Then the Max config was imported back in.
L.
PS: The issue manifests itself with DAQ Device control drop downs not seeing/finding any device: the drop down does not drop at all.
Some VIs using Daqmx open with many GUI object not showing up at all, and LV stops responding. (LV 2011). This issue appeared first after installing daqmx on a Win 7-64 laptop...

Internal Software error

Hi,
When I compile my fpga target vi i got an internal software error shown in the attached picture.
The program I'm working on is somehow complicated and the target file size is about 801KB and I also used 15 target-scoped FIFOs to transfer data within the target. I've also attached the log file. Does anyone know what caused this problem? Thanks in advance.
Attachments:
Untitled.png ‏40 KB
lvlog2011-10-06-13-05-10.txt ‏4 KB

It is an internal error generated by the application. I think the disc is still ok since the application is still preparing the data for burning to the disc and the actual burning has not yet started. Try running the program again and see if the error is still the same. If it displays a constant error every time you try burning the project, it is either the application can’t handle the size of the data that is going to be burned or there is an error in your system.
Run a disk check on your computer to see if there is any error that is preventing the application from working properly.
Right click on drive C and then select Properties.
Click Tools tab.
Click Check Now button.
Check Automatically fix file system errors and then click Start.
If no error was found try launching the application again. If it’s the same, use other video editing application where you can burn a video also.
http://www.techyv.com/

FPGA Internal software error

Hi,
I'm using labview 2009. When I compile the fpga target vi, i got the following message:
" An internal software error has occurred. Please contact National Instruments technical support at ni.com/support with the following information:#,910x,907x,911x,783x;781x,785x;784x,910x,907x,911x,783x;781x,785x;784x,9101;9102;9103;9104,9072;9073;9074;9144;9601;9602;9611;9612;9631;9632;9641;9642,9111;9112;9113;9114;9116;9118,7830;7831;7833;7811;7813,7851;7852;7853;7854;7841;7842,9101;9102;9103;9104,9072;9073;9074;9144;9601;9602;9611;9612;9631;9632;9641;9642,9111;9112;9113;9114;9116;9118,7830;7831;7833;7811;7813,7851;7852;7853;7854;7841;7842,Onboard,Onboard,Onboard,Onboard,Onboard,Derived,Derived,Derived,Derived,Derived#,,,,,,,,,,CONST_TCO_SPI,12.5,13.5,11.25,14.5,12.25,9.25,13.5,7.5,11.25,8.5CONST_TSU_SPI,2,4,3,2,4,4,4,4,4,4CONST_TH_SPI,4,4,4,4,4,4,4,4,4,4CONST_TSU_PLUS_TH_SPI,6,8,7,6,8,8,8,8,8,8#,,,,,,,,,,CONST_TSU_SSMISO,6,6,6,6,6,6,6,6,6,6CONST_TH_SSMISO,4,4,4,4,4,4,4,4,4,4CONST_TSU_PLUS_TH_SSMISO,10,10,10,10,10,10,10,10,10,10#,,,,,,,,,,CONST_9201_TCO_SPI,10,10,10,14.5,12.25,9.25,10,7.5,11.25,8.5
Method Name: <b>Compile For Target</b>"
Does anyone know what caused this problem? Thanks in advance.

Hello Kb1126,
To better be able to answer your question could you please share what RIO device you are working with, the RIO device software and any relevent Xilinix tools versions, as well as the possible version installed on your RT target (assuming you are using a RT controller to interface with your FPGA).
Thanks,
Blayne Kettlewell

MIO software error on cdaq 9188 / NI 9477

Similar Messages

Maybe you are looking for