Mismatch between preview in wwi template and cbgl_mp01 preview

Hello ,
I am getting a huge mismatch between the preview for label in wwi and the preview at the time of label printing through t-code cbgl_mp01 .Can anyone suggest me the troubleshooting techniques please .
Regards,
M D

Hello C B ,
I designed 4X6 inch label template in wwi . My label size is also 4X6.also my label stock size is also 4X6 . I have taken 4 as width and 6 as height in wwi and GLM config . I put 4 pictogram in my template . I am getting the 1st one full and the second one from top to right as half and both the below pictograms though it shows in preview but while doing print out it is missing . Has anyone come across this situation yet ? I tried a lot but the lower two pictograms are not coming into the printer paper .
M D

Similar Messages

Difference in displaying RAW files, between Camera RAW 5.3 and default preview...

Weird problem: when I import new RAW pics from my Canon (EOS 450D), they are previewed by the catalog viewer in very vivid and live colors. However when I try to edit them using Camera RAW 5.3, the INITIAL image that pops up is very dull... How come there is a difference in the algorithm when doing the "default" preview and the one used by the initial view of Camera RAW ?
I want to have the same "start" image in Camera RAW as shown by the default preview...
(I hope this is a clear enough exposition of the problem...)
Thanks!
Misha.

The initial image that pops up is a low resolution .jpg preview that is embedded in the RAW file.
The duller version is indeed your unprocessed RAW photograph. Processing should make it look just as good, or better, than that .jpg preview.

Mismatch between the Content Database size and the total of each site collection' storage used.

Hi All,
Environment: SharePoint 2010 with SP2.
Issue: One of the Content databases size in our farm shows 200 GB as used. There are 25 site collections in the DB and we counted
the total storage used of all site collections in that Content DB and is not more than 40 GB. (used "enumsites" command and counted the each sitecollections storage used).
What actions/troubleshooting were done?
Ran one script which will find the actual size of site collection and how much space used in the disk. But didn’t find major difference in the report.
Checked “Deleted from end user recycle bin “in all the site collections and no major storage is noticed.
Planning to Detach the problematic Content DB and attach ,will check whether any major effect is there
Why the Content DB shows 200 GB as used when the total storage used of all site collections is just 40 GB.
Appreciate suggestions from any one.
Best Regards,
Pavan Kumar Sapara.
s p kumar

Hi,
Thanks for your reply.
As there is only 20 MB of unallocated space for the above said DB, SQL DB team informed that they cannot perform the DB shrink at this moment.
So we are thinking to Offload all the site collections to other new DB and then will Drop the problematic database. In this way we can overcome the
issue.
Answer for your queries.
Are the mismatched sizes causing an issue? Are you short on diskspace for DB storage or SQL backups?
No, there is no issue with the mismatched sizes. We are not on short on disk space. We just worried why it occupies that much size(200 GB) when
the total storage used of all site collections in that DB is 40 GB.
Best Regards,
Pavan Kumar Sapara.
s p kumar

How can I reduce the width between search results and the preview fly-out?

Hello, I am using a custom masterpage that reduces the overall width of page content but I am seeing an issue with my enterprise search site. The search results look fine but there is a large horizontal gap between the results and document preview window
(when mousing over a word/excel/powerpoint result). This means that the preview fly-out is hardly visible unless the user scrolls horizontally to the right. Can someone tell me how to set a reduced width between the results web part and the preview window?
Example:

I think the issue is with the Callout orientation, have you customized the page and if so then you can customize the callout.
check "beakOrientation" and you can set values like topBottom, leftRight as per your requirement.
see here for more information -
http://msdn.microsoft.com/en-us/library/office/dn135236(v=office.15).aspx
Hope this helps!
Ram - SharePoint Architect
Blog - SharePointDeveloper.in
Please vote or mark your question answered, if my reply helps you

Mismatch between the patch version

Version 2.18, next step, next issue. Got through the 'Do Setup' step on "9-Apply DBA CUP and related patches" with a bug workaround that was provided. Now went to the next step of 'Do Execute' and it is failing with the message below. I've done some inital searching and haven't found an answer. There was one note on MOS about a very similar issue but it was resolved in 2.16. Posting here whild I spend more time researching and trying to figure out the reason. I also reviewed my notes from when I did this upgrade manually and these mereged patches were not applied in preinstall mode as the message is saying has to be done. Any help would be appreicated. Thanks!.
patchit12.sh - is exiting with no actions. ie. Patch patchfile_ad17089s not applied.
There is a mismatch between the patch version specified and the release
version obtained from your Applications environment. In order to apply
Release 12 patches to previous Applications versions, the patch must be
applied in preinstall mode.This can be done by passing the appropriate
value to the preinstall parameter of eof_patch12.sh.
INFO: Not starting patch alert monitor, to start: Login Engineer, User Admin, Update Profile
Version in scripts/COMMON
# $Header: patchit12.sh 1.32 2009/09/15 16:00:00 vpickard $
Edited by: user649511 on Mar 2, 2011 2:24 PM

You can change following in patchit12.sh under ./eof/scripts/COMMON. Please change it back before executing any other steps.
From
Check_Release()
#Check if the releasenr is OK
if [ "${preinstall}" = "y" ];then
RELEASE=12
echo
echo "patchit12.sh is installing: $patch in preinstall=y mode."
else
REL=`Get_Release`
RELEASE=`echo $REL | awk '{print substr($1,1,2)}'`
echo
echo "Found release REL=$REL from fnd_product_groups."
fi
to
Check_Release()
#Check if the releasenr is OK
if [ "${preinstall}" = "y" ];then
RELEASE=12
echo
echo "patchit12.sh is installing: $patch in preinstall=y mode."
else
REL=`Get_Release`
#RELEASE=`echo $REL | awk '{print substr($1,1,2)}'`
RELEASE=12
echo
echo "Found release REL=$REL from fnd_product_groups."
fi

Dreamweaver templates and search engines

I am running into a problem while building sites using
Dreamweaver's Template option. These sites are not easily found by
search engines. Anyone have any solutions?... without having to
stop using templates?
THANKS MUCH
cineaste_grrl

I can unequivocally guarantee you that there is no relation
between your use
of templates and your site's ranking by search engines. Can
you post a link
to the site, though, so we can see what the problem might be?
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"Cineaste_grrl" <[email protected]> wrote in
message
news:el1r2q$r0j$[email protected]..
>I am running into a problem while building sites using
Dreamweaver's
>Template
> option. These sites are not easily found by search
engines. Anyone have
> any
> solutions?... without having to stop using templates?
>
> THANKS MUCH
> cineaste_grrl
>

No preview displayed in Aperture and Preview after Lion "upgrade"

Hi everyone,
something (well, maybe many things) has been blown by Lion...I'm only just trying to figure out what exactly is.
Generally the system performs well but I have a big issue with previews within Aperture 3 and in Preview/Quicklook itself.
I'm testing Lion onto a late 2009 unibody macbookpro 13", 2.0 ghz, 8gb Ram; Aperture library is managed, around 100gb, all files are from Canon 30D and 350D, plus some jpegs and videos from a Powershot A620 (I didn't test the videos imported in Aperture yet, in SnowLeopard everything was fine).
In Aperture 3 (I have upgraded to 3.1.3 before installing Lion) my Canon 30D files are displayed correctly both in browser and viewer...Canon 350D files (raw images) aren't...well, the small thumbnail in the browser view is looking fine but when I double click to display the large image..it suddenly disappear! gray or black background, no image at all...back to browser view and the small thumbnail correctly display the image.
So i tried to regenerate the preview...nothing, same behaviour...if I press P for quick preview nothing is displayed, I get nothing even if I press M for master image.
Ok, I said...let's try this...I decide to export a photo, as master, onto the desktop...fine, the image icon is good, correctly displaying the image thumbnail...if I select it and press the spacebar i obtain ...absolutely nothing,a gray window that should be my image.
This happens also for the 30D files when I export them ...within Aperture they're good.
I also tried to export a version (jpeg)...all I obtain is a totally black jpeg.
Seems that Preview is not working anymore or uncapable to display any raw format, only jpegs are correctly displayed, I mean original jpeg shot.
I went through all the basic library maintenance for Aperture, repaired system permission before and after Lion installation...nothing changes.
Anyone experiencing a similar behaviour under Lion? Is Preview not working only in my system? Any suggestion?
I'm trying to find something to fix this...I have Time machine backups, Aperture vault backups so reverting back to SL is only a matter of patience and time...but I would like to stick with Lion and keep testing.
Any help or suggestion will be appreciated...I'm also searching for similiar behaviour (mostly for the problem with Preview) in the Lion OSX forum, this is heavily affecting Aperture.
Best regards,
Alberto

I found a solution that worked for me. Seems like my firewall did not accept the afp connection permissions anymore after installing lion... Since everything worked well turning off the firewall.
So if you don't want to keep your firewall disactivated here is what worked for me:
- Leave your firewall activated.
- Turn OFF afp file sharing in the sistem prefs
- Restart your Machine
- Turn ON afp file sharing
- You should now get a message if you want to accept afp connections...
- click YES
Thats it... Everything fine on my network now.

Mismatch between preview and output

Hi..
I'm new to After Effects, and having some problems with a project I'm working on..
It's a fairly simple project, just some tracking and replacing elements in a video clip.
Everything looks fine in the RAM preview, things line up and the timing looks good.
However, I run into problems when I want to render the final result.
Everything seems to be off, with regards to the timing. It looks like all my keyframes
are off by a few frames, leading to misalignment.
As I said, I'm new to After Effects (this is my first attempt at editing any kind of video),
and I suspect I screwed up right at the begining of my project.
The original footage is 23,970 fps, but I changed the composition framerate to 23,976 fps.
Can't remember why exactly, I suspect it had something to do with tracking in Mocha..
Could this be the reason my output is off?
Any tips on how to correct this, without trying to figure out how many frames each pre-comp
is off, and manually correcting them? I have about 20 elements which would need editing..
Any help is much appreciated!

If you cahnged the comp framerate, anturalyl you would also have to forcibly override the source footage framerate in the footage interpretation. Other than that you could be seing issues with interlaced footage where in the "inbetween" areas, that is the alternate field, your motion is interpolated linearly from the preceding even field to the next one on a whole frame basis, making it look misaligned because it is in teh wrong position, naturalyl. Check that, too. If all fails, force conform your footage to a "clean" framerate e.g. by time-stretching it and rendering a suitable clip for mocha. You can always go back to the original then or time-stretch back later or scale the keyframes temporally. Many ways to skin the cat....
Mylenium

Color mismatch between CS4 and Canon PIXMA PRO6500

Hi there! I am trying to research if anyone else is having a problem with color mismatch between CS4 and their printer. Last night I printed a .tiff image out of CS4 to my Canon PRO6500 printer and the sky came out purple / pink! It was supposed to be a stormy grey color. I have the color management turned off on the printer settings. I have CS4 manages color turned on and the correct ICC profile selected for the paper I am using. When I do a soft proof in CS4 the image looks fine, but when I print I get something completely different, mostly with the sky (purple / pink) color! Just for the heck of it I did a Print Preview under my Page Setup and guess what, the sky actually shows purple / pink! So I have no idea what's going on. I checked all my setting, ink cartridges, tried different paper with the appropriate ICC profile and no dice. Still have a goofy looking sky! I thought PROOFING the image is supposed to show you how the printed image is going to look? apparently it doesn't because it's not. The Print Preview has an accurate representation of the print but I have no idea where the pink / purple sky is coming from. They are supposed to be stormy clouds as I said. I appreciate any help anyone can provide .
Sabciu

I have the color management turned off on the printer settings.
But do you have a measured color profile based on a sample print? Most likely not, so this is not doing anything in your favor. The current profile may present the defaults for a given printer, but not the actual density based on your other printer settings. So by all means, unless you can be sure to obey a full calibration throughout, turn on the printer CM. Also, since it is a Pro model, you may actualyl have to use the dedicated RIP software that was bundled with it to get correct results, not the default windows print engine.
Mylenium

What is difference between Site template and web template

What is difference between Site template and web template

Both are almost same, are you referring to Site Definitions vs web template?, if so, refer to the following post
http://blogs.msdn.com/b/vesku/archive/2011/07/22/site-definitions-vs-web-templates.aspx.
--Cheers

The background behind my pages has turned black, how do i get it to go back to grey? i have switched between preview, normal, bleed, slug and presentation and closed and opened in design and it is still black. I can't imagine layouts with the black backgr

the background behind my pages has turned black, how do i get it to go back to grey? i have switched between preview, normal, bleed, slug and presentation and closed and opened in design and it is still black. I can't imagine layouts with the black background please help!

or maybe the interface has been set to Dark?
Go to Preferences > Interface tab, choose Light from Color Theme dropdown on Apearance section (upper part of the window)

There is a mismatch between order type and GL accountu201D.

Hello
Can any one help me to know why I am getting this error message.
Here I am giving the steps carried out.
Step1. Using transaction code: FB60 I have posted a vendor invoice to a Machinery account GL account against a internal order.
Step2. A down payment using transaction code FBA7. using a special indicator M to a bank account.
Step3. When I am trying to clear the open item (by selecting above both documents) for the vendor using transaction F-44 system is giving an error message u201CThere is a mismatch between order type and GL accountu201D. System is prompting to correct the down payment entry, where I dint use any Cost centre, internal order.
Checked the Internal order profile, AUC settlement profile etc and no able to find an error message.
Can any one explain me why this error is coming and what need to be check in order to rectify it.
Regards
RS.

Hi It looks that the field status of the Order Type and GL Account field status is being mistmatching with each other. You can check the field status group given on GL Account and the fields status in Order Type.

Fatal error C1900: Il mismatch between 'P1' version '20080116' and 'P2' version '20070207'

Hi all,
I have a Team Foundation Build Agent that has Visual Studio Team System 2008 Test Edition installed. One of the solutions that I compile with that Build Agent gives me the following errors:
VCBUILD : fatal error C1047: The object or library file '.\bin\Release\main.obj' was created with an older compiler than other objects; rebuild old objects and libraries
LINK : fatal error LNK1257: code generation failed
VCBUILD : fatal error C1900: Il mismatch between 'P1' version '20080116' and 'P2' version '20070207'
LINK : fatal error LNK1257: code generation failed
I've searched online and found that other people have experienced the same problem:
http://software.intel.com/en-us/forums/intel-c-compiler/topic/62516/
http://nuicode.com/issues/266
In the second posting one states "I had the same Error! After installing Service Pack1 for VS2008 it worked!". Thats great for him but I don't see any such update for the Test Edition of Visual Studio Team System 2008 - Test Edition.
What can I do to get rid of that problem?
Thanks!

Hello ACKH
I once handled a similar case in newsgroups. That case exhibit a almost same symptom. Please check out my summary below:
Problem
In that case, the customer has a DLL project that you had built on a machine where VS 2008 SP1 was installed. You then attempted to rebuild that project on a machine without SP1, and got a fatal compiler error C1900 “IL mismatch between ‘P1’ version ‘20080116’ and ‘P2’ version ‘20070207’”, and then LNK1257 “Code generation failed”. He found that rebuilding your static library alleviated the errors, but cannot accept this as a workaround because your clients will not have the ability to rebuild the libraries you distribute before they use them.
Cause
You had built the static library with the /GL (Whole Program Optimization) compiler switch, which requires Link Time Code Generation (/LTCG) when the static library is subsequently linked. These features require that all linked modules be built by the same version of the compiler. In fact, if precompiled headers are used, the same machine must build and link all the involved object code. Therefore, it is highly recommended that static libraries not be built with the /GL switch, since their intended use is quite frequently to support reuse by others.
Solution
You rebuilt the static library on your VS2008 SP1 machine without the /GL switch, and you no longer encounter this problem.
Please let me know if this info is helpful to you or not.
Regards,
Jialiang Ge
MSDN Subscriber Support in Forum
If you have any feedback of our support, please contact [email protected]
Please remember to mark the replies as answers if they help and unmark them if they provide no help.
Welcome to the All-In-One Code Framework! If you have any feedback, please tell us.

SSRS 2012 ERROR [IM014] [Microsoft][ODBC Driver Manager] The specified DSN contains an architecture mismatch between the Driver and Application

I have a SSRS installation, I have deployed my connections to, but they fail with title message. The drivers and ODBC on the box are setup and work fine with 32 bit ODBC conn manager.
When I run or configure my connections on the site, via the browser, I get errors connecting.
I tried to find which app pool http://server/ReportServer application used, but I am not finding that, so my first ?
How do I find in IIS what app pool SSRS application is using?
I have 2008 server, running SQL 2012 V.S. 2010 and I think I need to enable my app pool to use 32 bit, but cannot figure out which one it uses? I see default set to 32 bit = true, which I thought would be it.
Can I set my SSRS project to use x86, platform? Like I did with SSIS?
If so, how? SSRS and SQL 2012 somewhat new for me. Thanks
Developer MS Reporting Services

Hi DCady,
To manage a data source that connects to a 32-bit driver under 64-bit platform, we use C:\Windows\SysWOW64\odbcad32.exe. To manage a data source that connects to a 64-bit driver, we use C:\Windows\System32\odbcad32.exe.
Generally, if we use the 64-bit odbcad32.exe (C:\Windows\System32\odbcad32.exe) to configure or remove a DSN that connects to a 32-bit driver, for example, Driver do Microsoft Access (*.mdb), we will receive the following error message:
The specified DSN contains an architecture mismatch between the Driver and Application
To resolve this error, we need to use the 32-bit odbcad32.exe (C:\Windows\SysWOW64\odbacad32.exe) to configure or remove the DSN.
Besides, please make sure there are no DSN using the same name in both 64-bit and 32-bit ODBC Data Source Administrator.
Reference:
Managing Data Sources
Regards,
Mike Yin
If you have any feedback on our support, please click
here
Mike Yin
TechNet Community Support

Data mismatch between TABLE and Std. Extract str. (AFPO & 2LIS_04_P_MATNR)

Hi,
I am getting data mismatch in ECC standard table and ECC standard extract structure. Please help me.
I am using 2LIS_04_P_P_MATNR data source (standard extract structure).
I have following data in ECC Table (AFPO - Order Item).
AUFNR (Order Number) --> 4000460
PGMNG (Total planned quantity) --> 0
PSMNG (ORDER QTY) --> 2000
Extract Structure is showing following data.
AUFNR (Order Number) --> 4000460
PGMNG (Total planned quantity) --> 2000 (It should be zero)
PSMNG (ORDER QTY) --> 2000
I have checked with many other order numbers. The extract structure in RSA3 is showing correct values only if PGMNG is non-zero values. If PGMNG is zero, then it is automatically assigning PSMNG value.
Is this common? I want to display correct values for PGMNG from AFPO Table. Why this mismatch between table data and extract data. I have done all required steps refreshing data (deleting setup tables, filling set up tables etc.).
pls suggest. Poinsts will be assigned to every useful answer.
Thanks in advance.

Hi Avneet,
I have a similar problem where in AFPO shows value 1000 in PSMNG field and 1200 in RSA3 for extractor 2LIS_04_P_MATNR.
I have found that the standard feature of the extractor extracts the data at the time of release of process order. If the process order is changed after the release then the extractor will not picup the chagne.
Ex: AFPO value 1000 ---BI Value 1000
Now released in ECC
AFPO value 1000 ---BI Value 1000
In ECC value changed to 1500 after the release. BI will not pickup the change.
Extractor is pulling the data from MCAFPOV table. You can check the values, there it matches with RSA3 values.
I was just going thru forums for the solution. After i found the solution. I am just updating it.
Hope it helps you.
Thaks
Srikanth

Mismatch between preview in wwi template and cbgl_mp01 preview

Similar Messages

Maybe you are looking for