Missing Cisco 7960G config files

Hi
By mistake I'v deleted my configuration files for my phones, and I'm a total newbee in this area.
Can anybodt please post the files or a link to the files?
If possible with all config options writen in the files.
//Piet Pedersen

You can download 7960g software load, from the following URL:
http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml

Similar Messages

Cisco ACS config file

Hi all,
I have a cisco ACS V.4.0 server and want to get the config file. How can I get the CLI command prompt ? Or, Any where I can get the config file ?
Thanks
Leung Che Man

You can always take ACS backup from the GUI by going to System Configuration >> Click ACS Backup >> enter the FTP information >> Backup now.
Performing a Manual ACS Backup
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.0/user/guide/sba.html#wp222516
Once you connected to ACS via CLI the default username and password if not changed would be
user= Administrator
Pass= setup
Establishing a Serial Console Connection
http://cisco.biz/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/4.0/installation/guide/appliance/instalap.html#wpxref17544
Backing Up ACS Data From the Serial Console
http://cisco.biz/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/4.0/installation/guide/appliance/admap.html#wp1057928
Regds,
JK
Do rate helpful posts-

Missing palette - Config Files

The Config Files are missing from the subpalette in LV 2014-64 bit for Mac OS. I am not sure whether they were ever there. The files are in the expected locations. The palette is OK in the 32-bit version.
I have installed a bunch of stuff with VIPM and this may have contributed to the problem.
What I have tried:
Edit Palette Set... Restore to Default and Insert VIs.
Re-install LV.
Delete the config.mnu file.
Edit Palette Set... Delete icon. Insert subpalette. ... This gets me a config subpalette which contains every file in config.llb, not just the subset in the original subpalette.
So I am now to the point where I can work again but I would still like to get back to the default palette. Any suggestions?
Thanks,
Lynn

Try copying the mnu file from your 32-bit install (since that one works).
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Is it possible to create a cisco config file based on a polycom config file?

Hello,
We have 12 spa509g phones that are barely working with our provider (voxox).
My provider gave me the config files that are used to set up polycom phones as those are the only phones they support.
Features that currently work: incoming calls, outgoing calls, blind transfer, voicemail, call hold
Features that do not work: call presence - solid orange lights, attended transfer, paging
I've upgraded the firmware to 7.5.6 and configured the phone through the GUI as much as i can but I can't seem to enable the above features.
Any help would be highly appreciated as I'm about to buy polycom phones if we can't figure the configuration out.
Attached are the configuration files from voxox concerning polycom phones. confidential data says "removed"
If anyone thinks that this is possible, I can send a copy of my current cisco configuration file.
Thanks,
Philip

Well, I have no polycom phone, not I have personal experience with voxox. I wish the following document may help a lot - it describe Polycom configuration somewhat. As you have no Polycom, you have no current <mac>-directory.xml. So you don't know the device name you should subscribe to. But it seems to be a DID-number.
Just try it.
On the other side, ask Voxox for help. Don't ask for configuration files, ask for configuration instructions expressed in terms of the SIP protocols. Consider switch to more friendly and technically skilled VoIP operator if they will not understand what the SIP stand for ...
By the way, wrong forum. Your issue has nothing to do with XML Phone Application interface. I'm not sure someone will respond you here.

Message missing Essbase config file?

I am receiving a message saying that missing database config file? I am not aware of each database needed a config file.

Have you checked in the bin directory to make sure essbase.cfg file is there? HTH. Ricky [email protected]

Locking GUI of Cisco IP terminals leaving terminal unlock | via config file

Hi Guys,
On the Cisco SPA VoIP handset range, there is an option for a 'System Configuration User Password'.
This feature allows additional security within the GUI and also locks down some of the menus on the phones.
These phone menus can be overridden, leaving the GUI password in place. However, this is a manual process on the phone itself.
Is there any way of removing the user password on the handset, but keeping it live on the GUI and to do this all via the config file.
Regards
Shivam

What version is the older AP's on and what version is the new ones running? There were some changes with the config formatting between certain versions. Make sure all the AP's are running the same version and try loading the config again.

Phone Config Files Missing/Corrupt?

We just had an issue with a customer where all of their phones went down at once... when they rebooted the phones all got stuck at "Configuring IP Address".
I logged into the system to take a look, all the phones were unregistered.
When I did a debug on tftp events -- they were all trying to pull their config. (though it seems only the "Default" configs were going through successfully)
I did a "no create cnf-files" then "create cnf-files" in telephony-service.... this IMMEDIATELY fixed the problem -- all the phones were re-registered within seconds.
Has anyone seen this before? Any suggestions on what the cause could be?
It seems to be a 2-fold issue, 1. All the phones rebooted at the same time, 2. The config files were seemingly gone, corrupt, or inaccessible in some way.
For Cisco employees, SR #622640237 (UC520 - TAC)

Hi Daniel,
I have seen this before a few times, only ever though on a UC-520 and once only on a 540 but never on a UC-560... I don't know why each system exhibits different results/symptoms.
Something goes feral with the CNF files and in particular to SPA phones and older 7960/40 series (Never for the 7965 or 7975 phones), the only way to resolve it was to do what you did and replace the CNF's with new ones by running the "NO" command and reinstating it again.
This also mainly happens when it is a bad shutdown, moreso when it is a SAG or a Brownout and then complete powerdump, it is one of the first things to get effected by this.
Cheers,
David Trad.

How to I import MAX 4.6 config files into MAX 5.5? Missing Data Neighborhood. Strain gage set up is different.

I have been trying to import my config file from MAX 4.6 into a new system running MAX 5.5 and daq 9.8.
The data neighborhood does not appear, however my application sees the information. How can this be remedied? Start over? I have a lot of inputs and would rather not have to recreate all of them.
What is the difference between the strain gage settings in MAX 4.6 and MAX 5.5? The selection box for the bridge in 4.6 has a selection for "let niDAQ choose". Seems that is necessary to use the 4.6 config data. Try though I might, the readings in 5.5 do not match those in 4.6.     Is there a work around fo this? I don't want to have to perform an entire system calibration.
Thanks
Chris
Solved!
Go to Solution.

Attached JPG's.
Here is more information regarding the MAX Strain Set Up.
Attached are screen shots from MAX 4.6 and MAX 5.5.
Hardware: PXI chassis with bridge to a PC. SCXI-1520 input card.
Software: Old system: Windows XP SP2 running MAX 4.6 with niDAQmx 9.0.2,   programming in LabView 2011
                   New system: Windows 7 running MAX 5.5 with niDAQmx 9.8. Programming in LabView 2013
5.5: What is the gage factor? Is that the mv/v sensitivity of the load cell?
5.5: Asks for Gage resistance, easy to look up and I entered the data, 350.
5.5: How do I determine the Initial Voltage?
5.5: No choice of using V Excitation for scaling
5.5: Is Full Bridge I the same as 4.6 Full Bridge?
5.5: Requires use of Strain in scale factor
4.6: Requires use of Volts in scale factor (flags an error if I try Strain and requests Volts)
4.6: Choosing to use Vex for scaling makes readings look similar to 5.5 readings, but still not correct. ie around -79 in 5.5 and around -50 in 4.6 vs. 5.2 without.
Is there a way to set MAX 5.5 so that it provides the same starin set up function as 4.6? If so, what is it?
Thanks,
Attachments:
Max 4.6 Strain Set Up.jpg ‏32 KB
Max 5.5 Strain Setup.jpg ‏23 KB
MAX 4.6 Strain Scale 2.JPG ‏165 KB

Missing SSIS Extension in Config Files

As I understand it, in order to use an SSIS package as a data source in a report, I need to enable the SSIS extension in the RSReprotDesigner.config and RSReportServer.config files. That extension is in neither of these files. I have SSIS running on
my machine with Reporting Services.
The path to RSReportServer.config: C:\Program Files\Microsoft SQL Server\MSRS10_50.MSSQLSERVER\Reporting Services\ReportServer
The path to RSReportDesigner.config: C:\Program Files (x86)\Microsoft Visual Studio 9.0\Common7\IDE\PrivateAssemblies
Why is this extension not in either of these files?
The following is an abbreviated list of what's present in the RSReportServer.config file:
<Data>
<Extension Name="SQL"
<Extension Name="SQLAZURE"
<Extension Name="SQLPDW"
<Extension Name="OLEDB"
<Extension Name="OLEDB-MD"
<Extension Name="ORACLE"
<Extension Name="ODBC"
<Extension Name="XML"
<Extension Name="SHAREPOINTLIST"
<Extension Name="SAPBW"
<Extension Name="ESSBASE"
<Extension Name="TERADATA"
</Data>
The following is an abbreviated list of what present in the RSReporDesigner.config file:
<Data>
<Extension Name="SQL"
<Extension Name="SQLAZURE"
<Extension Name="SQLPDW"
<Extension Name="OLEDB"
<Extension Name="OLEDB-MD"
<Extension Name="ORACLE"
<Extension Name="ODBC"
<Extension Name="XML"
<Extension Name="RS"
<Extension Name="SHAREPOINTLIST"
<Extension Name="SAPBW"
<Extension Name="ESSBASE"
<Extension Name="TERADATA"
</Data>
I'm running SQL Server 2008 R2
ProductVersion ProductLevel Edition
10.50.1600.1 RTM Enterprise Edition (64-bit)
The operating system is Windows 7 Professional 64 bit.
Thank you for your help!
cdun2

The SSIS data extension was a non-production feature in SQL 2008. Due to an unreconcilable underlying security concern with the data extension, it was removed from 2008 R2. I believe the underlying data extension is still availabe on the disk, you would
need to manually add the entry to the server configuration file as noted in the following article. If you do, suggest you ensure that you trust the content of the SSIS packages being executed.
http://msdn.microsoft.com/en-us/library/ms345250(SQL.100).aspx
-JonHP
Microsoft SQL Server Reporting Services

Cisco 7920 and Aironet 1100 (Downloading config file)

For some reason the 7920 is trying to Downlaod the config file and can't pass that screen.
It authenticates just fine and the i get the screen "downloading config file" and that's it.
It's been doing the same thig all morning.
Not sure what's going on.
please help.
Call Manager 4.1.3 Aironet 1100
Thanks
Zeek

ok, so i guess after a while, the phone said "upgrading firmware" and after resseting, i got to the screen with the line up.
I still have a problem though.
i can dial a phone, it will call but once someone answer on the other side, the 7920 resets itself.
PLease help.

Cisco spa502g incorrect config file provisioned

Hi Guys,
Apologies if this is not in the right location for this question. But i have several phones which have not been rmeoved from the portal correctly or have been used as test phones on site. Now i have been able to get them removed from portal so that i can use them again however the issue i face is i cant reset the physical phones, they currently have a config file which if you log into the phone is asking for username and password so i cant check the URL for the provisioning file. I have no idea what this username and password would be and i have also tried doing it through the phone to no avail. I have read about how it may be possible to force a config file on using a tftp server, so have downloaded Solar winds but will be honest i have no idea how to do it. Nor have i got a config file to put on the phone.
I am in a business enviroment so have got a POE switch and plugged laptop directly in and a SPA502G plugged in next to it. I have left the device all weekend to see if it would pick up a new config file after it cant find one as this was advised to me by BT wholesale. This has not worked either.
Could somebody please asssit me with either explaining how i can get a config file on using solar winds tftp or if somebody knows another process on how i can reset these phones to ensure they have got the right provision file.
Look forward to your response.
Thank you

Wrong forum, post in "small business - SPA phones": You can move your posting with the Actions panel on the right.

Changing the Crystal Report dependency from 10.2 to 11.5 using config file

Hi,
We have an windows application in .net 2.0, which refers to Crystal Report 10.2 version. Now the dependency was being upgraded to 11.5. But we do not have the exact source code for the executable to change the dependency from 10.2 to 11.5.
I have installed the CR 11.5 to the testing machine and tried to open the appilcation. it failed saying CR 10.2 dlls were missing
Then I changed the .net config files to change the dependency assembly as follows
<runtime>
 <assemblyBinding xmlns="urn:schemas-microsoft-com:asm.v1">
 <dependentAssembly>
 <assemblyIdentity name="CrystalDecisions.CrystalReports.Engine" publicKeyToken="692fbea5521e1304" culture="neutral" />
 <bindingRedirect oldVersion="10.2.3600.0" newVersion="11.5.3700.0"/>
 </dependentAssembly>
 <dependentAssembly>
 <assemblyIdentity name="CrystalDecisions.ReportSource" publicKeyToken="692fbea5521e1304" culture="neutral" />
 <bindingRedirect oldVersion="10.2.3600.0" newVersion="11.5.3700.0"/>
 </dependentAssembly>
 <dependentAssembly>
 <assemblyIdentity name="CrystalDecisions.Shared" publicKeyToken="692fbea5521e1304" culture="neutral" />
 <bindingRedirect oldVersion="10.2.3600.0" newVersion="11.5.3700.0"/>
 </dependentAssembly>
 <dependentAssembly>
 <assemblyIdentity name="CrystalDecisions.Windows.Forms" publicKeyToken="692fbea5521e1304" culture="neutral" />
 <bindingRedirect oldVersion="10.2.3600.0" newVersion="11.5.3700.0"/>
 </dependentAssembly>
 </assemblyBinding>
</runtime>
Now the application launched with out any issues. I thought the problem was sorted out.
But when I tried to generate the report, there comes the problem
During the report generation, I am getting the following error
Crystal Reports
An error has occurred while attempting to load the Crystal Reports runtime.
Either the Crystal Reports registry key permissions are insufficient or the Crystal Reports runtime is not installed correctly.
Please install the appropriate Crystal Reports redistributable (CRRedist*.msi) containing the correct version of the Crystal Reports runtime (x86, x64, or Itanium) required. Please go to http://www.businessobjects.com/support for more information.
OK
I do not want to install the 10.2 redistributable in teh machine also do not want to re-compile the sources changing the dependency
Is there any way to achieve this ?
Any help is much appreciated.
Thanks
Edited by: Balaji Narasimhan on Aug 3, 2009 5:28 PM

No way that I know of. I believe once you change the dependency, you will have to recompile the project. Installing CR 10.2, may get this to work, but the app will most likely use the 10.2 references. Let's see if anyone else has any ideas.
Ludek

What's wrong? Verify and compare Cisco 2901 config after loading old config from Cisco 2801

Hi Cisco Community / Friends,
I am new to this site though I have cisco account for many years. I am a CCNA ,I passed my certification on January 2013 I seldom use and utilized my skills on networking becuase of my type of work. I am Project Eng'r working in a System integrator company . Anyway, I would like to ask assistance on the configurations of my Cisco router for this gov't projects.. Here's the situation.
We have a new project for the VSAT Comm'n of Coast Watch Station , The VSAT was installed 7 years ago. The VSAT was only used for a year by this Gov't agency because of subscription issue. Now, they wants to revive and use their VSAT facilities for the Coast watch monitoring. Now, some of this routers are working up to now and for some site are already defective so I need to replace the old 2801 router with a new equivalent model which is Cisco 2901. My plan was just to load the old config into the new Cisco 2901 router. However, after loading it to the new router, I am a little worried because I've got some errors received. I load the old config by copying the old files, edit it in notepad, and load the config using Secure CRT (terminal emulator). When I copy the old config of cisco 2801 to new router cisco 2901 , below are the command not recognized on Cisco 2901. What's wrong ? What are these commands for?
Appreciate your comments and help on this matter.. Thank You very much
Note: I Attached the original config from Cisco 2801 and the other file is the config after I load the config file to Cisco 2901.
(Errors see below)
CWS_4_Pandami(config-erm)#mmi polling-interval 60
                         ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi auto-configure
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi pvc
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#mmi snmp-timeout 180
                                                        ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-if)#interface GigabitEthernet0/1
CWS_4_Pandami(config-if)# description ===CWS4 SAT Modem===
CWS_4_Pandami(config-if)# bandwidth 256
CWS_4_Pandami(config-if)# ip address 192.168.42.1 255.255.255.0
CWS_4_Pandami(config-if)# duplex auto
CWS_4_Pandami(config-if)# speed auto
CWS_4_Pandami(config-if)# priority-group 1
                                                    ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config)#access-list 100 permit ip any any dscp cs5
CWS_4_Pandami(config)#priority-list 1 protocol ip high list 100
                          ^
% Invalid input detected at '^' marker.

Hi
From Cisco's website:
The Modem Management Interface (MMI) is software that enables auto-provisioning for the Cisco 827 routers. The MMI uses a fixed PVC to communicate with the Proxy Element (PE) residing on the digital subscriber line access multiplexer (DSLAM). Using MMI, the Cisco 827 router updates the running image and downloads the prescribed configuration using a configuration file or configuration values in a provisioning information database.
The customer premise equipment (CPE) can be automatically configured using the Cisco DSL CPE download, but it can be configured only with the image provisioning feature.
So because this is your device, you don't want to use MMI anyways.
And "priority-list" is QoS. Probably that QoS-command is old and removed, because now QoS is configured using class-maps and policy-maps.

Problem with mapping parameter when specified through an XML config file

I have decided to attept to stipulate UDT mapping parameters from C# to Oracle in the AppConfig File.
The original code (which worked) was as follows:
namespace RoyalLondon.Processes.Oracle.Dto
[OracleCustomTypeMappingAttribute("TEST_SCHEMA.T_PROJECT_CODE_CHANGES")]
class ProjectCodeChangeTableFactory : TableFactoryTemplate<ProjectCodeChangeTableDTO>
So, I've commented out the [OracleCustomTypeMappingAttribute line and added the following into the config file:
<oracle.dataaccess.client>
 <settings>
 <add name="ProjectCodeChangeTableDTO"
 value="udtMapping factoryName='RoyalLondon.Processes.Oracle.Dto.ProjectCodeChangeTableFactory, RoyalLondon.Processes, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null'
 typeName='T_PROJECT_CODE_CHANGES'
 schemaName='TEST_CON_DEV'"/>
 </settings>
</oracle.dataaccess.client>
This yields the following error message:
Unhandled Exception: System.InvalidOperationException: Custom type mapping for ' RoyalLondon.Processes.Oracle.Dto.ProjectCodeChangeTableDTO' is not specified or is invalid.
All the documentation I have read suggest that this ought to be ok. Is there anything obvious I am missing?

ummm, nevermind.
Turns out I hadn't updated the list of files that went in my servlet's jar file. I was recompiling the jar file successfully each time, but the list of files being included needed to contain a new class. This was a really stupid mistake on my part.
Just one of those things that I was bound to solve as soon as I broke down and posted something on the web. Sort of like taking your umbrella with you to ensure that it won't rain.
If anyone is reading this I am sorry I wasted your time.
Jon

SWFVISU task not appearing in any of the UWL Config files

Hello Workflow/Portal gurus, gotta question...
Scenario: I want custom workflow single-step tasks used in perf. mgmt. workflows to launch BSP application.
My understanding is that when you maintain link between workflow task and BSP application in SWFVISU followed by 'Register item types for all systems' in UWL and clearing Cache, UWL config file should be updated to include the task maintained in SWFVISU with appropriate launching parameters. I have used this successfully in the past with Wedbdynpro applications.
In my portal system, a new custom task that I maintain in SWFVISU is not even appearing in any of the UWL config file. when we use 'Register item types for all systems' option in UWL followed by clearing Cache,one of the config file does successfully get updated (we see success message and update date and time) but custom task is missing from the config.
Also, when I manually try to configure custom task and launching applications using one of the UWL wizard it gives error symbol with no messages. UWL behaves strange (Auth is not an issue) and couple of things we checked per UWL/Portal config docs seems to be in order.
Any pointers what we could be missing? Is there anything else other than adding task in SWFVISU followed by 'Register item types for all systems' in UWL and clearing Cache that needs to be done?
Appreciate your help,
Saurabh

Hi,
i had the same problem that all entries form SWFVISU could not be displayed in the XML config file.
The solution is very simple since SP 18 of NW portal: you need to configure a RFC destination in the Visual Admin (see Note 1133821).
Though if you are not using Delta Pull you have to create this destination to register the UWL.
I hope this helps.
Regards,
Marc

Missing Cisco 7960G config files

Similar Messages

Maybe you are looking for