Missing setipmm command under listenerconfig

Team,
I have been trying to test the mail merge feature on test environment and somehow I can not find a way to execute setipmm command on CLI. As per the user guide 8-5-6, Use the setipmm subcommand of listerconfig to enable the IPMM on the listener.
When I execute listerconfig command I see 4 options 1) NEW 2) EDIT 3) SETUP 4) DELETE and cli won't allow to execute setipmm command under any sub options. Any clue as to what am I missing? 
Thanks,
SJ

10.6.8
CS6
Essential or Advanced
I ended up uninstalling, restarting, reinstalling from the cloud.
I was missing the plugins.
I think I've resolved the issue.

Similar Messages

  • No dialer command under ISDN BRI interface

    Hi all,
    I have a 2901 router voice bundle with 4 ISDN BRI ports and would like to have them bundled under Dialer1 interface. Unfortunately it doesn't give me option for Dialer command under BRI interface as expected. 
    router(config-if)#int bri0/0/0
    router(config-if)#dia
    router(config-if)#dia
                             ^
    % Invalid input detected at '^' marker.
    router(config-if)#dialer
                             ^
    % Invalid input detected at '^' marker.
    router(config-if)#
    I assume it's down to the UC license installed on the device but not sure. Does the ISDN BRI interface behave in different way under this license?
    Pasting portion of "show ver" as well.
    Cisco CISCO2901/K9 (revision 1.0) with 479232K/45056K bytes of memory.
    Processor board ID 
    2 Gigabit Ethernet interfaces
    4 ISDN Basic Rate interfaces
    1 terminal line
    DRAM configuration is 64 bits wide with parity enabled.
    255K bytes of non-volatile configuration memory.
    250880K bytes of ATA System CompactFlash 0 (Read/Write)
    License Info:
    License UDI:
    Device#   PID                   SN
    *0        CISCO2901/K9          
    Technology Package License Information for Module:'c2900'
    Technology    Technology-package           Technology-package
                  Current       Type           Next reboot
    ipbase        ipbasek9      Permanent      ipbasek9
    security      None          None           None
    uc            uck9          Permanent      uck9
    data          None          None           None
    Configuration register is 0x2102

    Hi,
              Snippet of "sh ver" with IOS version is below:
    router#show ver
    Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(4)M5, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Fri 13-Sep-13 14:59 by prod_rel_team
    ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
    router uptime is 2 days, 21 hours, 47 minutes
    System returned to ROM by reload at 16:48:03 UTC Mon Aug 18 2014
    System restarted at 16:50:01 UTC Mon Aug 18 2014
    System image file is "flash0:c2900-universalk9-mz.SPA.152-4.M5.bin"
    Last reload type: Normal Reload
    Last reload reason: Reload Command
    The output of trying to type dialer command is in the initial post, I'm also pasting all available commands under bri0/0/0.
    router(config-if)#int bri0/0/0
    router(config-if)#?
    Interface configuration commands:
      aaa                     Authentication, Authorization and Accounting.
      access-expression       Build a bridge boolean access expression
      arp                     Set arp type (arpa, probe, snap), timeout, log
                              options or packet priority
      authentication          Auth Manager Interface Configuration Commands
      autodetect              Autodetect Encapsulations on Serial interface
      bandwidth               Set bandwidth informational parameter
      bgp-policy              Apply policy propagated by bgp community string
      bridge-group            Transparent bridging interface parameters
      carrier-delay           Specify delay for interface transitions
      cdp                     CDP interface subcommands
      clns                    CLNS interface subcommands
      clock                   Configure serial interface clock
      cwmp                    Configure CPE WAN Management Protocol(CWMP) on this
                              interface
      dampening               Enable event dampening
      default                 Set a command to its defaults
      delay                   Specify interface throughput delay
      description             Interface specific description
      dot1q                   dot1q interface configuration commands
      dot1x                   Interface Config Commands for IEEE 802.1X
      down-when-looped        Force looped serial interface down
      encapsulation           Set encapsulation type for an interface
      ethernet                Ethernet interface parameters
      exit                    Exit from interface configuration mode
      flow-sampler            Attach flow sampler to the interface
      full-duplex             Configure full-duplex operational mode
      h323-gateway            Configure H323 Gateway
      half-duplex             Configure half-duplex and related commands
      help                    Description of the interactive help system
      history                 Interface history histograms - 60 second, 60 minute
                              and 72 hour
      hold-queue              Set hold queue depth
      ip                      Interface Internet Protocol config commands
      iphc-profile            Configure IPHC profile
      ipv6                    IPv6 interface subcommands
      isdn                    ISDN Interface configuration commands
      isis                    IS-IS commands
      iso-igrp                ISO-IGRP interface subcommands
      keepalive               Enable keepalive
      line-power              Provide power on the line.
      llc2                    LLC2 Interface Subcommands
      load-interval           Specify interval for load calculation for an
                              interface
      logging                 Configure logging for interface
      loopback                Configure internal loopback on an interface
      mab                     MAC Authentication Bypass Interface Config Commands
      mac-address             Manually set interface MAC address
      macro                   Command macro
      metadata                Metadata Application
      mop                     DEC MOP server commands
      mtu                     Set the interface Maximum Transmission Unit (MTU)
      netbios                 Use a defined NETBIOS access list or enable
                              name-caching
      network-clock-priority  Configure clock source priority
      no                      Negate a command or set its defaults
      ntp                     Configure NTP
      ospfv3                  OSPFv3 interface commands
      pulse-time              Force DTR low during resets
      rate-limit              Rate Limit
      redundancy              RG redundancy interface config
      routing                 Per-interface routing configuration
      sdllc                   Configure SDLC to LLC2 translation
      serial                  serial interface commands
      service-policy          Configure CPL Service Policy
      shutdown                Shutdown the selected interface
      smds                    Modify SMDS parameters
      snapshot                Configure snapshot support on the interface
      snmp                    Modify SNMP interface parameters
      source                  Get config from another source
      tarp                    TARP interface subcommands
      timeout                 Define timeout values for this interface
      topology                Configure routing topology on the interface
      transmit-interface      Assign a transmit interface to a receive-only
                              interface
      trunk-group             Configure interface to be in a trunk group
      tx-ring-limit           Configure PA level transmit ring limit
      vpdn                    Virtual Private Dialup Network
      vrf                     VPN Routing/Forwarding parameters on the interface
      waas                    WAN Optimization
    router(config-if)#

  • Missing Navigation Tab under taskbar properties

    Windows 2012 is missing Navigation Tab under taskbar properties
    There are only three tabs taskbar, jump lists and toolbars
    domain environment
    Muhammad Mehdi

    Hi Muhammad,
    As far as I know, the tabs under Taskbar Properties should be as follows:
    As displayed in the picture, there is no Navigation tab here.
    Best regards,
    Frank Shen

  • Black frame around icons when highlighted - double commands under the apple

    when anything highlighted with a mouse click a black frame appears - also there are double commands under the apple menu - example
    shut down
    shut down
    restart
    restart
    I did every trick I could think of - safe, single user, open firmware reset-all, account cache, disc utility, - only one account is effected, other accounts are ok - Monday was first time, I was 1 hour away form rebuilding account when the problem went away, on its own - this morning its back on a different machine, again just one account - G5 running 10.4.8 - any ideas?

    Turn off
    SystemPreferences>UniversalAccess>Seeing>VoiceOver
    While you're at it, go to the Keyboard&Mouse preferences>KeyboardShortcuts and uncheck the VoiceOver shortcut (Cmd-F5)

  • Commands under "menu'

    Hi
    I add 4 commands to my canvas: Exit, Command1, Command2, Command3.
    It shows on the cellular Menu, Command1 and Exit. Under Menu I have Command2 and Command3.
    I want that only Menu and Exit will be on cellular screen and all Command1-3 will be under Menu. How can I do it?
    Thanks.

    Many(all?) Nokia phones will put your commands under 'Options' if you use generic Midp1.0 code, regardless of the priorities and types of the Command's.
    The way around this is to use the Nokia specific libraries for full-screen and draw your own command labels. This way you can control exactly what is visible. What you do is include nokiaui.zip (find on nokia developer site somewhere) in your build path, and extend the FullCanvas class instead of using a normal Canvas. This will get you full-screen on even Midp1.0 Nokia devices.
    The FullCanvas class has constants KEY_SOFTKEY1, and KEY_SOFTKEY2 that represent the Canvas.getGameAction(int keyCode) of the left and right soft-key's, so you can tell which corner key was pressed.
    I hope this helps, I remember going through this problem when I released my first game a couple years back, and the distributor told me that the commands were stacking under 'Options' for nokia's.

  • Cisco WS-C4948 missing qos commands

    Hi all,
    I've hunted high and low and cannot seem to be able to enable shaping, bandwidth or priority under a class in a policy-map on a Cisco WS-C4948.
    All documentation I have read on this switch on the Cisco website says that all these commands are possible.
    Example : http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/12.2/50sg/configuration/guide/qos.html#wp1436874
    Switch# configure terminal
    Switch(config)# policy-map policy1
    Switch(config-pmap)# class class1
    Switch(config-pmap-c)# shape average 256000
    When I try to replicate I get:
    Switch# configure terminal
    Switch(config)# policy-map policy1
    Switch(config-pmap)# class class1
    Switch(config-pmap)# ?
    Policy-map class configuration commands:
      dbl              Dynamic buffer limiting
      exit             Exit from QoS class action configuration mode
      netflow-sampler  NetFlow action
      no               Negate or set default values of a command
      police           Police traffic matching current class
      service-policy   Configure QoS Service Policy
      set              Set QoS values
      trust            Set trust value for the class
      <cr>
    Am I missing a global command to enable shaping?
    Thanks guys.

    Hi Leo,
    Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 12.2(54)SG1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Thu 27-Jan-11 11:39 by prod_rel_team
    Image text-base: 0x10000000, data-base: 0x123FB194
    ROM: 12.2(31r)SGA7
    Dagobah Revision 226, Swamp Revision 5
    Switch uptime is 3 days, 19 hours, 59 minutes
    System returned to ROM by power-on
    System restarted at 19:06:24 AEST Thu Nov 28 2013
    System image file is "bootflash:cat4500-entservicesk9-mz.122-54.SG1.bin"
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected]
    cisco WS-C4948 (MPC8245) processor (revision 0) with 262144K bytes of memory.
    Processor board ID FOX1205G7TQ
    MPC8245 CPU at 266Mhz, Fixed Module
    Last reset from PowerUp
    3 Virtual Ethernet interfaces
    48 Gigabit Ethernet interfaces
    511K bytes of non-volatile configuration memory.
    Configuration register is 0x2102
    Thanks

  • TFTP command under solaris 10

    I use tftp in solaris 10,like follows:
    $ tftp
    tftp> connect 127.0.0.1
    tftp> ls
    ?Invalid command
    tftp> put a.txt
    Transfer timed out.
    I want to know if I need to configure tftp under solaris 10,if need,how to configure it?
    how to show directory and file after connect command,which command I can use? ls is not right command. when I want to put a file,why Transfer timed out. I am puzzled with it. Which directory is source directory and which directory is destinate directory?A detailed example is better.
    Thanks

    You cannot list directory contents with tftp. If you want any sort of interactive session, use ftp.

  • [Trend Micro Ios content filtering] parameter-type command under policy map not available

    Hi, all:
    I'm trying to configure TrendMicro IOS content filtering. I have this working on a separate box, running 15.1.
    On this particular testbed, I have a 2900 running:
    System image file is "flash0:c2900-universalk9-mz.SPA.152-3.T1.bin"
    And the following licensing:
    Technology Package License Information for Module:'c2900'
    Technology    Technology-package           Technology-package
                  Current       Type           Next reboot 
    ipbase        ipbasek9      Permanent      ipbasek9
    security      securityk9    Permanent      securityk9
    uc            uck9          Permanent      uck9
    data          datak9        Permanent      datak9
    Configuration register is 0x2102
    CUBE_GOLD_MEX#show ip trm subscription status
           Package Name:  Security & Productivity (Trial)
                 Status:  Active
    Status Update Time:  18:02:51 CST Mon Jul 23 2012
        Expiration-Date:  Mon Aug 20 02:00:00 2012
        Last Req Status:  Processed response successfully
    Last Req Sent Time:  18:02:51 CST Mon Jul 23 2012
    CUBE_GOLD_MEX#
    Also, I have the following config lines on it:
    ip host trps.trendmicro.com 216.104.8.100
    ip name-server 4.2.2.2
    ip cef
    multilink bundle-name authenticated
    parameter-map type urlfpolicy trend tm-pmap
    allow-mode on
    [snip]
    parameter-map type trend-global trend-glob-map
    class-map type inspect match-all http-imap
    match protocol http
    class-map type urlfilter trend match-any drop-category
    match url category Abortion
    match url category Activist-Groups
    match url category Adult-Mature-Content
    match url reputation ADWARE
    match url reputation DIALER
    match url reputation DISEASE-VECTOR
    match url reputation HACKING
    match url reputation PASSWORD-CRACKING-APPLICATIONS
    match url reputation PHISHING
    match url reputation POTENTIALLY-MALICIOUS-SOFTWARE
    match url reputation SPYWARE
    match url reputation VIRUS-ACCOMPLICE
    policy-map type inspect urlfilter trend-policy
    class type urlfilter trend drop-category
    I have not been able to get to the good part of configuring the ZBF.
    I've looked over several configuration examples and can't figure out what I'm doing wrong, since I'm not able to see the command 'parameter-map' under the 'policy-map urlfiltering'
    XXXXXX(config)#policy-map type inspect urlfilter trend-policy
    XXXXXX(config-pmap)#?
    Policy-map configuration commands:
      class        policy criteria
      description  Policy-Map description
      exit         Exit from policy-map configuration mode
      no           Negate or set default values of a command
    XXXXXX(config-pmap)#
    I thought it might be an issue with version 15.2.3, but according to configuration guides, commands are the same.
    Can anyone provide some assistance?
    TIA.
    c.

    Hi Carlos,
    I am having the same problem.  I have seen a few diffenent configuration examples and they all show adding the "parameter type urlfpolicy trend parm-map-name" command but it doesn't exist, at least in 15.2(3)T1 and I see it listed in the the IOS documentation for 15.2.  Maybe they forgot it :-)
    I guess I will open a TAC case as I do not want to downgrade...
    I will keep you posted if I find the answer.
    Regards,
    Troy

  • Missing Database Options under Configure menu in Sequence Editor

    In my TestStand 4.0 Sequence Editor, the "Database Options" is missing under "Configure" menu. Does anyone know how to enable this option?
    Thanks

    Glad that was it! Definitely narrows things down.
    These entries on the Configure menu are controlled by a special type of sequence in the process model called Configuration entry points. If you open up one of the default models, you will see a sequence in the Sequences pane called "Configure Database Options". This is the default database options sequence.
    It's possible that your custom model contains a Configure Database Options sequence, but that it isn't configured to be an entry point. You can change this setting by right-clicking the sequence and choosing Sequence Properties. 
    If the custom model does not contain the database functionality at all, further work may be required to add that functionality in. Here's a document explaining how to add new configuration entry points to a process model: http://www.ni.com/white-paper/3837/en Depending on whether this model was originally based on one of our default models and how much of the original database logging code is still present, it may require a fair amount of work to reimplement that functionality. It might be a good idea to contact the person who created this custom model to find out more information about why those database options were removed and how difficult it might be to reimplement them.
    Daniel E.
    TestStand Product Support Engineer
    National Instruments

  • Trunk-group command under controller T1 in which IOS is available

    Hi All,
    Quick question, I would like to know if the trunk-group under the controller t1 is available in the 15.T train currently I have the following IOS
    152-2T
    153-1T
    and neither IOS have the command. But in the 15.M train (151-4M) I have it.
    Basically what I want to accomplish is to reserve 2 B channels for Emergency calls, something like this:
    controller T1 0/0/0
    pri-group timeslots 1-24
    trunk-group Emergency timeslots 1
    trunk-group Standard timeslots 2-24
    Thanks in advance
    Regards
    Carlito

    Hi,
    The Chris is right, if you did not declare the trunk group before, he'll be available at the interface T1 Pri.
    Ex:
    trunk group Emergency
    hunt-scheme longest-idle both
    controller T1 0/0/0
    pri-group timeslots 1-24
    trunk-group Emergency timeslots 1
    Regards.
    J Rosa

  • Distance command under BGP process

    Hi,
     Can someone explain me how does the command 
    "distance 200 10.0.0.1 0.0.0.0 DEFAULT" under a BGP process executes.
    On this router default route is learnt through ospf .
    10.0.0.1 is BGP neighbor ip address
    DEFAULT is standard access-list with permit 0.0.0.0 statement.
    ==========================================================
    The ospf default route is preferred over the default route of BGP neighbor in this scnario.
    However i want to know how this command executes.
    Thanks

    If you receive that route via eBGP (AD 20) the router will change to 200 if it learned via neighbour 10.0.0.1 giving preference to OSPF AD 120. Resuming the RIB will have the OSPF route

  • Missing App category under Library section

    So I had upgraded to the newest iTunes a week ago or so but havent restarted my computer in a while which I did today. So when I opened iTunes it said welcome this is your first time using itunes etc.. My library was all there and its the usual welcome screen. I noticed right away that under the Library section the App category was missing? I plugged my ipod touch in and all my apps were still there in the app section there (you know where you check mark the ones you want). I synced to make sure and possibly hope the section would come up but it hasn't. I don't know whats up has this section been taken down in the update or is this some kind of glitch. Should I try to install the new itunes again? Thanks for the help

    You're welcome, and thanks for the points.
    Oh, I absolutely DO believe you. A lot of software seems to be like that - enabling/disabling options gets them working properly, so good guess on that!

  • Missing menu commands in Itunes 6

    Ever since I downloaded Itunes 6, I am missing certain menu commands like "File," the ability to create playlists or enter/change track information.
    Anybody else have similar problems? I am at a loss as far as what to do...
    Thanks!
    Lynda

    Somehow the titlebar became skinned. I just left-clicked the titlebar area, selected options, and unchecked skin the titlebar... Can't believe I spent hours trying to figure that out.

  • Options missing on iMovie under File Analyze Video

    Hi. I just got the new iLife 11 and was looking through the video about the people finder on this page. http://www.apple.com/ilife/imovie/
    However, when I look at iMovie on my computer I don't see the mark camera pans option under file-analyze video and the button that shows the keyword editor is not there. How do I get these options to appear?

    Wow! Didn't even know that was there! Thanks for the speedy reply. Has that always been there? And would you mind just giving me a brief description of the other things it enables and how to access them? Because I didn't know what most of the other stuff was on the list. Thanks so much for your help!

  • Missing "config" command in CLI (Cisco 1140 AP)

    Hi All
    I am trying to chang IP configuraton for my Cisco 1140 AP, but in CLI I dont have a "config" command (i used en before to enable administrative mode)
    Bellow are the commands I can see:
    AP7081.0506.d54a#?
    Exec commands:
      cd               Change current directory
      clear            Reset functions
      clock            Manage the system clock
      crypto           Encryption related commands.
      debug            Debugging functions (see also 'undebug')
      delete           Delete a file
      dir              List files on a filesystem
      disable          Turn off privileged commands
      enable           Turn on privileged commands
      exit             Exit from the EXEC
      fsck             Fsck a filesystem
      help             Description of the interactive help system
      led              LED functions
      lock             Lock the terminal
      login            Log in as a particular user
      logout           Exit from the EXEC
      lwapp            lwapp exec commands
      mkdir            Create new directory
      monitor          Monitoring different system events
      more             Display the contents of a file
      name-connection  Name an existing network connection
      no               Disable debugging functions
      ping             Send echo messages
      pwd              Display current working directory
      release          Release a resource
      reload           Halt and perform a cold restart
      rename           Rename a file
      renew            Renew a resource
      rmdir            Remove existing directory
      send             Send a message to other tty lines
      set              Set system parameter (not config)
      show             Show running system information
      systat           Display information about terminal lines
      terminal         Set terminal line parameters
      test             Test subsystems, memory, and interfaces
      traceroute       Trace route to destination
      undebug          Disable debugging functions (see also 'debug')
      upgrade          Upgrade software
      verify           Verify a file
      where            List active connections
    In addition, I am keep getting the following messages:
    *Mar  1 00:38:13.933: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
    *Mar  1 00:38:23.883: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    I am not sure what I am doing wrong. I try to do a hard reset but it didnt work.
    Any ideas?

    Thanks
    Another queastion:
    I verified that my AP is Lightweight by the part id (AIR-LAP1141N)
    Now, when I browse to Cisco download page, I have 3 options for OS:
    - Autonomous AP IOS Software
    - IOS Boot Images
    - IOS Software
    - Lightweight AP IOS Software
    Which of the above should I use in order to switch the AP to regular mode?
    Does anyone knows what is the difference between IOS software and the Autonomous IOS software?

Maybe you are looking for