Mixed Environment/Airport Extreme Base Statiion/Can't access PC files

I have a wireless network via Airport Extreme Base Station. I have 2 PC's and 3 Mac's connected to the network.
I can connect to the Internet from every computer.
Through my wireless network:
From the PCS, I can access files on each other and on all of the Macs.
From the Macs, I can access the files on the other Macs.
What I am having trouble doing is accessing shared files on the PC from any of the Macs. Can anyone help?
Powermac G4 Dual 533 Mac OS X (10.4.8) PC running Windows XP - SP2

What I am having trouble doing is accessing shared files on the PC from any of the Macs. Can anyone help?
Check out this iFelix article to see if it will help.

Similar Messages

This Airport Extreme base station can't connect to iCloud

I have a Airport Extreme base station (model A1408) running firmware 7.6.4.
In troubleshooting a Back to My Mac issue, I noticed that the configuration page for the base station had a yellow dot next to my apple id in the "Back to My Mac" section of the "Base Station" tab, with words underneath that say, "This Airport Extreme base station can't connect to iCloud".
When I delete the id and re-enter it, the dot goes green and no errors are generated (the id/password tokens are accepted). Then, I push "Update", and after the base station comes back, the light is yellow again. (To be clear, the dot next to the apple id is yellow, not the base station status light, which is always green.)
I'm connected to Xfinity Cable Internet service via a Motorola SB6141.
Everything iCloud related works for my various iOS and MacOS devices except Back to My Mac.
Can anyone point me to a solution? I've already been through Apple's troubleshooting and support docs related to Back to My Mac.
Thanks in advance!

NEVER MIND!
After reverting to the old LinkSys router, I left the AEBS powered up all night. This morning, I tried once again and the AEBS mysteriously started working with my laptop after reconnecting and power-cycling the cable modem. Go figure!
Unfortunately, the iMac in another room doesn't seem to be able to join the new network, but I'll close this thread and perhaps open a new one after doing some more trouble-shooting.
Thanks for your comments and suggestions.
-- Mike

Currently use Airport Express -1st Generation-to access internet -purchased 2014 Airport Extreme base station -can I import Express back up configuration to keep current settings . Or is it best to do new Airport Extreme as a new Network .

Currently use Airport Express -1st Generation-to access internet -purchased 2014 Airport Extreme base station -can I import Express back up configuration to keep current settings . Or is it best to do new Airport Extreme as a new Network .

Just spoke with Cisco about the router. They said the router is compatible with the E1500. They suggested that I contact Apple to see if their default IP address was that same as the router (192.168.1.1). They told me I would have to change it if that was the case. How would I do that?

HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer. We still have wifi but cannot access the base station software.

Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
Is there a way to resolve this issue?

Airport extreme base..Can i rest my cable modem on top of it?

Can I set my cable modem ontop of the airport extreme base? Or will it interfer with the base?

Short answer: YES!
As already said; it will be fine.
Nick

Airport extreme guest network can't access internet

I upgraded to the 7.6.1 a few weeks ago and recently noticed some oddities, My guest network clients get an IP in the 10.x.x.x network but can't access the internet, the private network is just fine. I looked on the airport utility for any advanced wireless options to indicate setting for the guest but I didn't see anything.
Is this the desired method of operation? My private network is using the 192.168 network, do I have to set my GUEST network to the same range in order to get out with it?
I use a lion server on the network that is also giving out IP via the Lion DHCP Service, is there some other change I need to make to the Airport Extreme to have it forward the Guest network dhcp requests to the Lion Server?
Any help would be appreciated.
Mike.

Turns out when I set my DNS server IP for my APE DHCP to my Internal IP on my Lion server, the Airport Extreme is not allowing those guests to talk to my DNS Server so I updated the DNS to be my external/Public IP and now the guest network can do DNS and access all the cool stuff on the internet.

Configure TC and Airport Extreme Base Stations with different channels

I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap. I thought I would post my results here since I didnt' find a good article online.
Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup.
Setup is a 3 flloor house where the 3 wired network locations have wireless overlap. The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel. In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels. I am writing this from memory, so feel free to ask questions and I will track this topic:
Procedure
Setup time capsule as your base station. Do all the setup for your wireless and guest networks. Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
Plug your first airport extreme/access point into your wired network. Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
Use the airport utility to first configure it to "extend" your wired network.
Then, go in and reconfigure it manually in the airport utility. Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137).
Now go to the top tab and click on the "internet" icon
Go to the DHCP tab and change it to "bridge mode." This will tell the AE to not give out IP addresses (the TC will do this for you). If you get an error that the IP ranges conflict, you have not done this
Note that if you have a guest network setup, you will need to set this up on the AE as well.
Now test your airport setup. Take your client (macbook, iOS device) and connect to your network. Move to a spot near the TC and pull up a web page. Keep an eye on the signal strength and beginv moving toward the AE. Refresh the page as you move around. You should at some point see the signal strength increase. Refresh your page again. You should be now connected to to the AE. I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
Another test you can do is to start backing up on your TC and then test the move. The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
If you need to setup another AE, simply follow setups 3-10.
I hope this helps others. I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products.

I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap. I thought I would post my results here since I didnt' find a good article online.
Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup.
Setup is a 3 flloor house where the 3 wired network locations have wireless overlap. The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel. In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels. I am writing this from memory, so feel free to ask questions and I will track this topic:
Procedure
Setup time capsule as your base station. Do all the setup for your wireless and guest networks. Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
Plug your first airport extreme/access point into your wired network. Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
Use the airport utility to first configure it to "extend" your wired network.
Then, go in and reconfigure it manually in the airport utility. Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137).
Now go to the top tab and click on the "internet" icon
Go to the DHCP tab and change it to "bridge mode." This will tell the AE to not give out IP addresses (the TC will do this for you). If you get an error that the IP ranges conflict, you have not done this
Note that if you have a guest network setup, you will need to set this up on the AE as well.
Now test your airport setup. Take your client (macbook, iOS device) and connect to your network. Move to a spot near the TC and pull up a web page. Keep an eye on the signal strength and beginv moving toward the AE. Refresh the page as you move around. You should at some point see the signal strength increase. Refresh your page again. You should be now connected to to the AE. I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
Another test you can do is to start backing up on your TC and then test the move. The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
If you need to setup another AE, simply follow setups 3-10.
I hope this helps others. I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?

apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

Can the AirPort Extreme Base Station be plug-in to the power forever?

Hi,
sorry for my english but this is my question: Can the AirPort Extreme Base Station be plug-in to the power (electricity) forever? I mean, I don't have to un-plug the Base Station sometimes? Thanks
Alvaro

Sounds more like an issue with your router and
network than a problem with AEBS.
Which router?
I certainly do not need to reboot my AEBS like that,
I think I have rebooted it once in two years!
I would start a new thread describing your network in
more detail and the issues with the AEBS.
Thank you, but my diagnosis is the result of many days
of experiment with about hundreds of users. It's a bug,
I know were it is. It was reported to Apple in september
(2005).
It isn't that easy to upgrade at the same time all the
wireless (802.11b and 802.11g) that do have to interoperate
smoothly within the same space.
I don't think anyone need to waste more time on these
bugged firmware versions (5.6 & 5.7) as I already explained
it. They work smoothly just in a limited environment
which they were conceived for: one Mac connected to one
AEBS connected to one FAI.
You can't recommand these version to colleagues who have
to live in a real world with other wireless equipment
(a Mac not updated, an ABS not updated,
a Cisco wireless card emitting to 100 mW and smashing all
the neibourhood, a pre 802.11g+ card using 2 channels at
the same time...).
dan

Mac Book pro can't connect to Internet through Apple airport extreme base station

I had problems connecting to the internet in the past with my macbook pro. One day it suddenly started working again but then I bought a second apple TV I lost connectivity. I have tried changing the IP address manually and while it shows me connected to the wifi I am still with out internet. When I hooked up the new Apple TV that I bought it booted my computer from it's ip address. The apple TV though wouldn't work and now nor would my computer. I ended up setting the Apple TV's ip address manually and now it works fine. My computer on the other hand does not no matter if I set it manually or not. Even if I plug in the ethernet cable from the base station it doesn't work. It show that it has a self assigned IP address. After I set it manually it shows that I am connected both via wifi and the ethernet cable but I can't connect to the internet. If I plug the modem directly into the computer bypassing the base station I get internet and it is using the IP address that worked originally.
It has something to do with the connection from the base station to my computer but this is odd considering every other device I have: iPhone 4, apple tv, apple tv, apple mini with retina display all work perfectly via wifi (newest apple tv had to be set manually as I stated above but now works fine). When I check the ip of the base station itself it seems to be different from the ip of the computer when the computer was connected directly to the router. I don't understand why my computer now can't connect to the internet via the base station whether it be wifi or by ethernet. Can you please help me trouble shoot this?
I have an AirPort Extreme base station which allows up to 50 users and a 30 meg connection speed.
I have a MacBook Pro (17-inch Early 2009), OS X Mavericks (10.9.2)

It has something to do with the connection from the base station to my computer
I don't think so..
I just posted a reply which totally vanished.. strange strange website now.
Please post some screenshots of your AE setup from the airport utility.. I want to see the summary page, then the network and internet tab.
Please tell us what modem you use.. is it a router??
If you have satellite or 3G wimax etc service they often are limited to 5 IP addresses... the AE takes one and then 4 more devices can join .. no more.
You need to also give us the screenshot of the IP you are getting in a computer that works.
EDIT
Sorry this is half double post.. the previous page refused to display.. now it has returned..

Can I use an Airport Extreme Base Station from the USA in Europe ?

A friend of mine gave me an Airport Extreme Base Station from the USA to Germany. When I hook it up to my PB by ethernet cable the Computer can't find the Base Station at all. If I use my Sonnett Aria Extreme PCI card it finds the station but in the pop-up menu asking in which country I want to use the airport station it only offers North and South American countries. How do I go from here and why is my PB not finding the station when I'm using cables ? Has it something to do with different models for different countries ? Any idea ? Thanx

Here you go ...
Changing the Radio Channel on the AEBSn
Either connect to the AEBSn's wireless network, or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN ports of the AEBSn, and then, using the AirPort Utility in Manual Setup, check these settings:
AirPort - Wireless
o Channel: <Use Automatic or select a preferred channel>

How can I extend a wireless network with my AirPort Extreme Base Station?

Today I purchased a brand new, dual-band base station to replace my Belkin N router, as I have had a handful of firewall, coverage, and other networking problems in my house lately. First off, I really like this router and it was very easy to setup. My MacBook Pro could use both bands and established a 300 Mbit/s link very quickly. After tweaking various settings to my liking, I was also able to maximize the connections on many of my non-Apple machines and devices. I noticed that the range of its network was better than my Belkin's, but unfortunately, it failed to completely saturate the area sufficiently. Since the Belkin still works well enough, I was hoping I could bridge them together one way or the other.
The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct? I would like to place them at opposite ends of my home so I can get strong WiFi signals everywhere inside. However, when I try to get the base station to connect to my preexisting WiFi connection, it tells me that I can't extend the network and fails to join.
So is this possible? And if it is, how would I go about setting it up? I know it would probably be easier if I had a simple range booster such as an AirPort Express, but I didn't buy one while I was at Fry's since I hoped I could make use of the older Belkin. This is its product page, if needed. Thanks for any suggestions.
-MacUser

The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct?
Sorry, but no. The AirPort Extreme Base Station cannot "join" a network like the AirPort Express or Time Capsule, but you wouldn't want to do this anyway because in this configuration these devices will only perform as wireless clients ... not routers.
Instead, the AirPort Extreme can either be extended or can extend another 802.11g or 802.11n AirPort ... or a very very few non-AirPort devices.
One option for your Belkin would be to connect it to the AirPort Extreme by Ethernet but this may not meet your requirements or be a desirable situation. Otherwise, you would need to get another AirPort to extend your current one.

I have a Cisco wireless router. Can I buy an Airport Express plug in booster for a distant part of my house or do I need an Airport Extreme base station instead to make the Airport Express plug in booster work?

Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?

You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
The bottom line here......you always need two Apple routers if you want to extend the network wirelessly.

Can't use my HP Deskjet F4580 Wireless Printer with the AirPort Extreme Base. The printer is NOT connected at the USB port of the AirPort Extreme, and is placed in another room. It worked just fine with my previous router (Linksys WRT54G). Help me!

Hey Guys!
I just got my AirPort Extreme Base, but I can't use my HP Deskjet F4580 wireless printer with it.
The printer is not connected to the AirPort Extreme's USB port. It is placed in another room, and I'd like to use it (the printer) wirelessly (not connected to the USB port os the AirPort Extreme), as I used to. There is no place for the printer close the AirPort Extreme. It worked just fine with my previous wireless router (Linksys WRT54G). I'm very disappointed with the AirPort Extreme Base Station because of that!...
Can you help me? Please?!
Thanks Folks!

This must be a tough one, no suggestions at all.

Can't read iPhoto library from external drive via airport extreme base stat

I can't seem to open my iPhoto library from my external USB drive that is hooked and being shared through my airport extreme base station. If I plug the external drive directly to my mac via USB it works but not when going through the base station.
This only started happening when I upgraded from iLife'06 to iLife'08.
Anyone have any ideas on how to fix?

That's a problem that many are posting about. Haven't read of a solution yet. Be sure to report the problem to Apple at: http://www.apple.com/feedback/iphoto.html.
Do you Twango?
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've written an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 08 libraries. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

Mixed Environment/Airport Extreme Base Statiion/Can't access PC files

Similar Messages

Maybe you are looking for