MMC with Computer Management Utility & Sun Storage 7110 in CIFS ?

Is it possible and supported to manage the filer SUN Storage 7110 configured in CIFS with the "Computer Management utility (MMC)" from Windows?
I've tried without success :-(...
Thanks in advance for the support.
Regards,
Joaquim Neves

I believe your source for users/groups should ideally come from LDAP or Active Directory. The "Users" interface is primarily for assigning administration capabilities for the 7110 itself.

Similar Messages

Where to find the fishworks appliance for SUN Storage 7110

Hi,
we've got an old Storage 7110 we would like to re-use, but some disks have been interverted and that may be causing the problem: there's just no system booting up, hence no Storage interface available. All we got in the iLO working.
Is the appliance system supposed to be installed in one of the disks in the front bays ? How to recover or to install the appliance, which seems to be "fishworks" ? I coudln't find any full release of Fishworks anywhere, only some patches are [made available|https://wikis.oracle.com/display/FishWorks/Fishworks].
Thanks
-pph

989293 wrote:
yep, thanks, there isn't even the GRUB menu left. It tries to boot a weired Windows 2003 which ends up with a blue screen ok, that is definitely wrong.
But is the original operating system supposed to be installed on one of the disks or somewhere else, maybe inside on a flash disk ?The 7110 uses two of the 16 disks that are front-accessible for the OS. The 7120 has two extra disks on the back.
By the way, what firmware should I use to upgrade the machine ? I found the the latest update for X4240 servers (SW 3.2.1) but none for Storage 7110. Is it ok if I use the X4240 firmware to update ? It proposes to update both, ILOM and BIOS (v68) but the bios doesn't seem to get updated (still getting xxxsomethingxxx64).I am not 100% sure but I think you should not upgrade the iLOM and BIOS on your own and they are included in the software updates that are installed via the GUI. So I think without contacting support it might be impossible to revive this system
Bjoern

Recreate pool problem on a 7110 Sun Storage

Hi,
we have a Sun 7110 that runs mostly well, except when the iscsi volume fills up, the volume stop, and we have to drop it and recreate it. 3 weeks ago, to counter that, I switched on dedup and compression. No idea if it is a good or bad idea, but because we got lots of i/o hanging on the volume :
- we tried to drop again the volume via the web interface.
- after destroying it, impossible to recreate it, so we switch to the shell to see what's going on. In fact all space was filled up into the "zombie" share (pool-0/???/zombie). No idea what it is, because we never got snapshots. And the cpu was still in the roof like it was still compressing, deduplicating or what...
- we decided to connect to destroy the whole pool (with difficulty), and the CPU stop working as crazy
Now impossible to recreate it via the web interface.
- i can create the pool with zpool and create volume with zfs but they don't show up in the interface
- if we destroy again and try to create it in the web interface, we have of course no pool in the "Available pool", so I try to create it BUT i can't:
Model     Sun Storage 7110
Data Devices     -
Log Devices     -
Cache Devices     -
as is there weren't any disks!
I checked : the disks are ok from the OS point of view (/var/ak/logs/debug.sys doesn't complain for example, except for a spare disk that I labeled back)
Any idea how to "reset" the storage pool?
Do I must go through the "factory reset" (I'm not even sure it can help).
Or should I forgot Sun/oracle appliance kit, and install freenas instead? :-)
Any help will be appreciate (or similar concerns :-) )
Nicolas Zin

I answer to myself:
factory reset solved the problem.
Dawn box!

Sun Storage Common Array Manager software

trying to configure two storage arrays and cannot find the original disks
found the website with link to the Sun Storage Common Array Manager software
http://www.oracle.com/us/products/servers-storage/storage/san/fc/common-array-manager/resources/index.html
but it is a dead link...
now i need this software or the two storage arrays cannot be reconfigured
maintenance for them have lapse so my oracle support is not an option
any links to be able to obtain the software... doesn't matter even if older version... doesn't need to be latest

No Good, everytime i go to the download section for software relating to hardware i keep getting asked to
Add Support Identifiers …
just a log in account isn't good enough
so back to my original problem, even though we own the equipment outright, they are essentially a couple of expensive paperweights
it shouldn't be that hard to obtain even an older version of this necessary piece of software?
is it possible to obtain support identifiers for sun hardware with expired maintenance? maybe that will allow me to at least download the version of the software that was available at the time of expiration?

Is there a Java utility class to help with data management in a desktop UI?

Is there a Java utility class to help with data management in a desktop UI?
I am writing a UI to configure a network device that will be connected to the serial port of the computer while it is being configured. There is no web server or database for my application. The UI has a large number of fields (50+) spread across 16 tabs. I will write the UI in Java FX. It should run inside the browser when launched, and issue commands to the network device through the serial port. A UI has several input fields spread across tabs and one single Submit button. If a field is edited, and the submit button clicked, it issues a command and sends the new datum to the device, retrieves current value and any errors. so if input field has bad data, it is indicated for example, the field has a red border.
Is there a standard design pattern or Java utility class to accomplish the frequently encountered, 'generic' parts of this scenario? lazy loading, submitting only what fields changed, displaying what fields have errors etc. (I dont want to reinvent the wheel if it is already there). Otherwise I can write such a class and share it back here if it is useful.
someone recommended JGoodies Bindings for Swing - will this work well and in FX?

Many thanks for the reply.
In the servlet create an Arraylist and in th efor
loop put the insances of the csqabean in this
ArrayList. Exit the for loop and then add the
ArrayList as an attribute to the session.I am making the use of Vector and did the same thing as u mentioned.I am using scriplets...
>
In the jsp retrieve the array list from the session
and in a for loop step through the ArrayList
retrieving each CourseSectionQABean and displaying.
You can do this in a scriptlet but should also check
out the jstl tags.I am able to remove this problem.Thanks again for the suggestion.
AS

Have a 4S and in the lock screen it is coming up with a screen (Not Enough Storage - This iphone cannot be backed up because there is not enough iCloud storage available. You can manage your storage in settings) it then has option close or settings.....bu

I have a 4S and in the lock screen it is coming up with a screen (Not Enough Storage - This iphone cannot be backed up because there is not enough iCloud storage available. You can manage your storage in settings) it then has option close or settings.....but i am unable to click on either or turn off the phone. I have plugged it into itunes on the computer and manually backed it up but i cannot use my phone as i cant get past this message

Welcome to the Apple Community.
You might try a forced shutdown to begin with, hold down the top and home buttons together until the device shuts down, then restart it.

Is Sun Storage 7000 Storage replication adapter compatible with 2540 series

We are evaluating VMWare Site Recovery Manager 4.0. Is Sun Storage 7000 Storage replication adapter compatible with 2540 Sun Storage series?

I would say the short answer would be no. The 2540 is a LSI based device, the SRM adapter for that is written by LSI. The 7000
series array is based on OpenSolaris and ZFS, quite a different beast.

Sun update manager with patch manager

I need to use both products since I have systems running Solaris 10, 9 and 8. Is there a way to get them to work together?
Ideally, I would like to have 1 system talk to SUN to manage the application and downloads. I would want the system to distribute the patches to all the other systems.

Yes, this is possible. We would recommend setting up Sun Update Manager on Solaris 10 as your patch proxy (with a connection to Sun). Both Update Manager on Solaris 10 and Patch Manager on Solaris 8 and 9 can then be configured as clients.

I have a problem with session manager session files because of the invalid json storage data submited by firefox

Hi, i have problem with session manager's session files. The problem is: the submitted storage data from firefox which is put between "storage":{ and its matching closing brace } But in some of my session files there is non equal { and } under storage's braces. I need to get storage data but in my case it is very hard to do. My question is there any char put before or after { and } like /{ or \{ to avoid confusion? If there is not such thing, i think there could be different solution but i am not sure: i look couple of my session files; after "storage":{...} there is ,_"formDataSaved" so i can get storage data in this example ... by looking between "storage":{ and ,"_formDataSaved" easily. Is there every time ,"_formDataSaved" after "storage":{ ? Thank you.

Well, it seems waiting is not my strong suit..! I renamed a javascript file called recovery to sessionstore. This file was in the folder sessionstore-backups I had copied from mozilla 3 days ago, when my tabs were still in place. I replaced the sessionstore in mozilla's default folder with the renamed file and then started mozilla. And the tabs reappeared as they were 3 days ago!
So there goes the tab problem. But again when I started mozilla the window saying "a script has stopped responding" appeared, this time the script being: chrome//browser/contenttabbrowser.xml2542
If someone knows how to fix this and make firefox launch normally, please reply! Thank you

I am using Iphone 4S, Problem is my PC is not detecting iphone as a storage device, i tried with device manager, tried to install drivers but its showing drivers allready installed, Pls can any one help

I am using Iphone 4S, Problem is my PC is not detecting iphone as a storage device, i tried with device manager, tried to install drivers but its showing drivers allready installed, Pls can any one help

try this and see if it works: connect your iPhone and open up iTunes on your PC. Go to your phone's page. Under Summary page, check manually manage music and videos.

Oracle VM: Sun server x3-2 with Sun Storage 2540 M2

Hello Everyone!
Currently, we are planning to implement a project about Visualization using Oracle VM.
As the Sun Storage 2540 M2 uses FC channel to share its luns from storage, we are not sure on how to discover those share storage luns to be use in Oracle VM manager and Oracle VM Server.
So, could you please help guide us, give us some recommendations, or instruction documents to the issue above?
Thank so much in advance!
Regard,
Dara

Hmm, server is not (auto?)discovered
though machines can see each other via network, all ports are opened, but agent still reports
[2011-07-28 21:07:32 6001] DEBUG (OVSNotificationServer:233) NOTIFICATION SERVER STARTED
[2011-07-28 21:07:32 6005] INFO (OVSRemaster:101) REMASTER SERVER STARTED
[2011-07-28 21:07:32 6009] INFO (OVSMonitor:29) MONITOR SERVER STARTED
[2011-07-28 21:07:32 6013] INFO (OVSHA:103) HA SERVER STARTED
[2011-07-28 21:07:33 6017] INFO (OVSStat:234) STAT SERVER STARTED
[2011-07-28 21:07:33 6021] INFO (OVSAgentServer:274) OVSAgentServer start serving!
[2011-07-28 21:07:33 6021] INFO (OVSAgentServer:275) Oracle VM Server version: {'release': '3.0.2', 'date': '201109270901', 'build': '75'}
[2011-07-28 21:07:37 6009] DEBUG (OVSMonitor:46) Cluster state changed from [Unknown] to [Offline]
[2011-07-28 21:07:37 6009] DEBUG (OVSMonitor:50) Error sending notification: Cannot get manager URL from agent db.
[2011-08-14 23:30:58 13993] DEBUG (agtctl:95) master flag: None
A slight off-subject question, do I need to run anything on OVM (apart from setting on all servers the same password)?

Mac os 10.5 accessing sun storage via smb

Dears
I have three mac 10.3.9 machines .those can access a sun storage device normallyin the same local net using smb.I installed another system 10.5 on those machines, but unfortunately trying to connect to the sun storage you can see the connecting bar for a very long time with no response.I installed a new mac Leopard 10.5.2 machine in the same network , and this last computer can connect to the storage server .So I upgraded the three one's to 10.5.2 with no improvemnt , even to 10.5.5.Those three if restarting as 10.3.9 can be connected .all network settings were checked.
appreciating in advance your help.
yahya

I apologize for the delay in responding to you. I was on the road all day yesterday.
OK. I switched the printer's Ethernet cable to a Linksys Switch (Model EZX S55W) that's part of this local network. That did not work. I swapped out the cable for one that I know works. Still no change. I switched the printer's Ethernet cable directly to a port on the router. No change. I even swapped cables here, too, but no success.
As I was doing all this, I was wondering: When I select the HP P1606dn printer in the Print and Fax "Add" dialog box, (see the image below) and the Print Using pulldown menu displays "Please select a driver or printer model" and the message "Searching for new drivers" appears under it (with the spinning wheel), why is it that the Ethernet connection to printer is critical to "finding" a new (printer) driver?
Isn't the utility searching through my system and libraries looking for a printer driver app for the printer that I identified/selected in the dialog box?
After all, if the dialog box lists the printer among those to choose from, hasn't the utility already discovered the printer via the Ethernet connection?

Too Slow - Domino 6.5.4 with access manager agent 2.2 ?

I don't know how to tune Domino 6.5.4 with access manager agent 2.2?
I think AMAgent.properties is not good for SSO.
Please help me to tune it.
# $Id: AMAgent.properties,v 1.103 2005/09/19 22:08:34 madan Exp $
# Copyright ? 2002 Sun Microsystems, Inc. All rights reserved.
# U.S. Government Rights - Commercial software. Government users are
# subject to the Sun Microsystems, Inc. standard license agreement and
# applicable provisions of the FAR and its supplements. Use is subject to
# license terms. Sun, Sun Microsystems, the Sun logo and Sun ONE are
# trademarks or registered trademarks of Sun Microsystems, Inc. in the
# U.S. and other countries.
# Copyright ? 2002 Sun Microsystems, Inc. Tous droits r閟erv閟.
# Droits du gouvernement am閞icain, utlisateurs gouvernmentaux - logiciel
# commercial. Les utilisateurs gouvernmentaux sont soumis au contrat de
# licence standard de Sun Microsystems, Inc., ainsi qu aux dispositions en
# vigueur de la FAR [ (Federal Acquisition Regulations) et des suppl閙ents
# ? celles-ci.
# Distribu? par des licences qui en restreignent l'utilisation. Sun, Sun
# Microsystems, le logo Sun et Sun ONE sont des marques de fabrique ou des
# marques d閜os閑s de Sun Microsystems, Inc. aux Etats-Unis et dans
# d'autres pays.
# The syntax of this file is that of a standard Java properties file,
# see the documentation for the java.util.Properties.load method for a
# complete description. (CAVEAT: The SDK in the parser does not currently
# support any backslash escapes except for wrapping long lines.)
# All property names in this file are case-sensitive.
# NOTE: The value of a property that is specified multiple times is not
# defined.
# WARNING: The contents of this file are classified as an UNSTABLE
# interface by Sun Microsystems, Inc. As such, they are subject to
# significant, incompatible changes in any future release of the
# software.
# The name of the cookie passed between the Access Manager
# and the SDK.
# WARNING: Changing this property without making the corresponding change
# to the Access Manager will disable the SDK.
com.sun.am.cookie.name = iPlanetDirectoryPro
# The URL for the Access Manager Naming service.
com.sun.am.naming.url = http://sportal.yjy.dqyt.petrochina:80/amserver/namingservice
# The URL of the login page on the Access Manager.
com.sun.am.policy.am.login.url = http://sportal.yjy.dqyt.petrochina:80/amserver/UI/Login
# Name of the file to use for logging messages.
com.sun.am.policy.agents.config.local.log.file = c:/Sun/Access_Manager/Agents/2.2/debug/C__Lotus_Domino/amAgent
# This property is used for Log Rotation. The value of the property specifies
# whether the agent deployed on the server supports the feature of not. If set
# to false all log messages are written to the same file.
com.sun.am.policy.agents.config.local.log.rotate = true
# Name of the Access Manager log file to use for logging messages to
# Access Manager.
# Just the name of the file is needed. The directory of the file
# is determined by settings configured on the Access Manager.
com.sun.am.policy.agents.config.remote.log = amAuthLog.Dominoad.yjy.dqyt.petrochina.80
# Set the logging level for the specified logging categories.
# The format of the values is
#     <ModuleName>[:<Level>][,<ModuleName>[:<Level>]]*
# The currently used module names are: AuthService, NamingService,
# PolicyService, SessionService, PolicyEngine, ServiceEngine,
# Notification, PolicyAgent, RemoteLog and all.
# The all module can be used to set the logging level for all currently
# none logging modules. This will also establish the default level for
# all subsequently created modules.
# The meaning of the 'Level' value is described below:
#     0     Disable logging from specified module*
#     1     Log error messages
#     2     Log warning and error messages
#     3     Log info, warning, and error messages
#     4     Log debug, info, warning, and error messages
#     5     Like level 4, but with even more debugging messages
# 128     log url access to log file on AM server.
# 256     log url access to log file on local machine.
# If level is omitted, then the logging module will be created with
# the default logging level, which is the logging level associated with
# the 'all' module.
# for level of 128 and 256, you must also specify a logAccessType.
# *Even if the level is set to zero, some messages may be produced for
# a module if they are logged with the special level value of 'always'.
com.sun.am.log.level =
# The org, username and password for Agent to login to AM.
com.sun.am.policy.am.username = UrlAccessAgent
com.sun.am.policy.am.password = LYnKyOIgdWt404ivWY6HPQ==
# Name of the directory containing the certificate databases for SSL.
com.sun.am.sslcert.dir = c:/Sun/Access_Manager/Agents/2.2/domino/cert
# Set this property if the certificate databases in the directory specified
# by the previous property have a prefix.
com.sun.am.certdb.prefix =
# Should agent trust all server certificates when Access Manager
# is running SSL?
# Possible values are true or false.
com.sun.am.trust_server_certs = true
# Should the policy SDK use the Access Manager notification
# mechanism to maintain the consistency of its internal cache? If the value
# is false, then a polling mechanism is used to maintain cache consistency.
# Possible values are true or false.
com.sun.am.notification.enable = true
# URL to which notification messages should be sent if notification is
# enabled, see previous property.
com.sun.am.notification.url = http://Dominoad.yjy.dqyt.petrochina:80/amagent/UpdateAgentCacheServlet?shortcircuit=false
# This property determines whether URL string case sensitivity is
# obeyed during policy evaluation
com.sun.am.policy.am.url_comparison.case_ignore = true
# This property determines the amount of time (in minutes) an entry
# remains valid after it has been added to the cache. The default
# value for this property is 3 minutes.
com.sun.am.policy.am.polling.interval=3
# This property allows the user to configure the User Id parameter passed
# by the session information from the access manager. The value of User
# Id will be used by the agent to set the value of REMOTE_USER server
# variable. By default this parameter is set to "UserToken"
com.sun.am.policy.am.userid.param=UserToken
# Profile attributes fetch mode
# String attribute mode to specify if additional user profile attributes should
# be introduced into the request. Possible values are:
# NONE - no additional user profile attributes will be introduced.
# HTTP_HEADER - additional user profile attributes will be introduced into
# HTTP header.
# HTTP_COOKIE - additional user profile attributes will be introduced through
# cookies.
# If not within these values, it will be considered as NONE.
com.sun.am.policy.agents.config.profile.attribute.fetch.mode=NONE
# The user profile attributes to be added to the HTTP header. The
# specification is of the format ldap_attribute_name|http_header_name[,...].
# ldap_attribute_name is the attribute in data store to be fetched and
# http_header_name is the name of the header to which the value needs
# to be assigned.
# NOTE: In most cases, in a destination application where a "http_header_name"
# shows up as a request header, it will be prefixed by HTTP_, and all
# lower case letters will become upper case, and any - will become _;
# For example, "common-name" would become "HTTP_COMMON_NAME"
com.sun.am.policy.agents.config.profile.attribute.map=cn|common-name,ou|organizational-unit,o|organization,mail|email,employeenumber|employee-
number,c|country
# Session attributes mode
# String attribute mode to specify if additional user session attributes should
# be introduced into the request. Possible values are:
# NONE - no additional user session attributes will be introduced.
# HTTP_HEADER - additional user session attributes will be introduced into HTTP header.
# HTTP_COOKIE - additional user session attributes will be introduced through cookies.
# If not within these values, it will be considered as NONE.
com.sun.am.policy.agents.config.session.attribute.fetch.mode=NONE
# The session attributes to be added to the HTTP header. The specification is
# of the format session_attribute_name|http_header_name[,...].
# session_attribute_name is the attribute in session to be fetched and
# http_header_name is the name of the header to which the value needs to be
# assigned.
# NOTE: In most cases, in a destination application where a "http_header_name"
# shows up as a request header, it will be prefixed by HTTP_, and all
# lower case letters will become upper case, and any - will become _;
# For example, "common-name" would become "HTTP_COMMON_NAME"
com.sun.am.policy.agents.config.session.attribute.map=
# Response Attribute Fetch Mode
# String attribute mode to specify if additional user response attributes should
# be introduced into the request. Possible values are:
# NONE - no additional user response attributes will be introduced.
# HTTP_HEADER - additional user response attributes will be introduced into
# HTTP header.
# HTTP_COOKIE - additional user response attributes will be introduced through
# cookies.
# If not within these values, it will be considered as NONE.
com.sun.am.policy.agents.config.response.attribute.fetch.mode=NONE
# The response attributes to be added to the HTTP header. The specification is
# of the format response_attribute_name|http_header_name[,...].
# response_attribute_name is the attribute in policy response to be fetched and
# http_header_name is the name of the header to which the value needs to be
# assigned.
# NOTE: In most cases, in a destination application where a "http_header_name"
# shows up as a request header, it will be prefixed by HTTP_, and all
# lower case letters will become upper case, and any - will become _;
# For example, "common-name" would become "HTTP_COMMON_NAME"
com.sun.am.policy.agents.config.response.attribute.map=
# The cookie name used in iAS for sticky load balancing
com.sun.am.policy.am.lb.cookie.name = GX_jst
# indicate where a load balancer is used for Access Manager
# services.
# true | false
com.sun.am.load_balancer.enable = false
####Agent Configuration####
# this is for product versioning, please do not modify it
com.sun.am.policy.agents.config.version=2.2
# Set the url access logging level. the choices are
# LOG_NONE - do not log user access to url
# LOG_DENY - log url access that was denied.
# LOG_ALLOW - log url access that was allowed.
# LOG_BOTH - log url access that was allowed or denied.
com.sun.am.policy.agents.config.audit.accesstype = LOG_DENY
# Agent prefix
com.sun.am.policy.agents.config.agenturi.prefix = http://Dominoad.yjy.dqyt.petrochina:80/amagent
# Locale setting.
com.sun.am.policy.agents.config.locale = en_US
# The unique identifier for this agent instance.
com.sun.am.policy.agents.config.instance.name = unused
# Do SSO only
# Boolean attribute to indicate whether the agent will just enforce user
# authentication (SSO) without enforcing policies (authorization)
com.sun.am.policy.agents.config.do_sso_only = true
# The URL of the access denied page. If no value is specified, then
# the agent will return an HTTP status of 403 (Forbidden).
com.sun.am.policy.agents.config.accessdenied.url =
# This property indicates if FQDN checking is enabled or not.
com.sun.am.policy.agents.config.fqdn.check.enable = true
# Default FQDN is the fully qualified hostname that the users should use
# in order to access resources on this web server instance. This is a
# required configuration value without which the Web server may not
# startup correctly.
# The primary purpose of specifying this property is to ensure that if
# the users try to access protected resources on this web server
# instance without specifying the FQDN in the browser URL, the Agent
# can take corrective action and redirect the user to the URL that
# contains the correct FQDN.
# This property is set during the agent installation and need not be
# modified unless absolutely necessary to accommodate deployment
# requirements.
# WARNING: Invalid value for this property can result in the Web Server
# becoming unusable or the resources becoming inaccessible.
# See also: com.sun.am.policy.agents.config.fqdn.check.enable,
# com.sun.am.policy.agents.config.fqdn.map
com.sun.am.policy.agents.config.fqdn.default = Dominoad.yjy.dqyt.petrochina
# The FQDN Map is a simple map that enables the Agent to take corrective
# action in the case where the users may have typed in an incorrect URL
# such as by specifying partial hostname or using an IP address to
# access protected resources. It redirects the browser to the URL
# with fully qualified domain name so that cookies related to the domain
# are received by the agents.
# The format for this property is:
# com.sun.am.policy.agents.config.fqdn.map = [invalid_hostname|valid_hostname][,...]
# This property can also be used so that the agents use the name specified
# in this map instead of the web server's actual name. This can be
# accomplished by doing the following.
# Say you want your server to be addressed as xyz.hostname.com whereas the
# actual name of the server is abc.hostname.com. The browsers only knows
# xyz.hostname.com and you have specified polices using xyz.hostname.com at
# the Access Manager policy console, in this file set the mapping as
# com.sun.am.policy.agents.fqdn.map = valid|xyz.hostname.com
# Another example is if you have multiple virtual servers say rst.hostname.com,
# uvw.hostname.com and xyz.hostname.com pointing to the same actual server
# abc.hostname.com and each of the virtual servers have their own policies
# defined, then the fqdnMap should be defined as follows:
# com.sun.am.policy.agents.fqdn.map = valid1|rst.hostname.com,valid2|uvw.hostname.com,valid3|xyz.hostname.com
# WARNING: Invalid value for this property can result in the Web Server
# becoming unusable or the resources becoming inaccessible.
com.sun.am.policy.agents.config.fqdn.map =
# Cookie Reset
# This property must be set to true, if this agent needs to
# reset cookies in the response before redirecting to
# Access Manager for Authentication.
# By default this is set to false.
# Example : com.sun.am.policy.agents.config.cookie.reset.enable=true
com.sun.am.policy.agents.config.cookie.reset.enable=false
# This property gives the comma separated list of Cookies, that
# need to be included in the Redirect Response to Access Manager.
# This property is used only if the Cookie Reset feature is enabled.
# The Cookie details need to be specified in the following Format
# name[=value][;Domain=value]
# If "Domain" is not specified, then the default agent domain is
# used to set the Cookie.
# Example : com.sun.am.policy.agents.config.cookie.reset.list=LtpaToken,
# token=value;Domain=subdomain.domain.com
com.sun.am.policy.agents.config.cookie.reset.list=
# This property gives the space separated list of domains in
# which cookies have to be set in a CDSSO scenario. This property
# is used only if CDSSO is enabled.
# If this property is left blank then the fully qualified cookie
# domain for the agent server will be used for setting the cookie
# domain. In such case it is a host cookie instead of a domain cookie.
# Example : com.sun.am.policy.agents.config.cookie.domain.list=.sun.com .iplanet.com
com.sun.am.policy.agents.config.cookie.domain.list=
# user id returned if accessing global allow page and not authenticated
com.sun.am.policy.agents.config.anonymous_user=anonymous
# Enable/Disable REMOTE_USER processing for anonymous users
# true | false
com.sun.am.policy.agents.config.anonymous_user.enable=false
# Not enforced list is the list of URLs for which no authentication is
# required. Wildcards can be used to define a pattern of URLs.
# The URLs specified may not contain any query parameters.
# Each service have their own not enforced list. The service name is suffixed
# after "# com.sun.am.policy.agents.notenforcedList." to specify a list
# for a particular service. SPACE is the separator between the URL.
com.sun.am.policy.agents.config.notenforced_list = http://dominoad.yjy.dqyt.petrochina/*.nsf http://dominoad.yjy.dqyt.petrochina/teamroom.nsf/TROutline.gif?
OpenImageResource http://dominoad.yjy.dqyt.petrochina/icons/*.gif
# Boolean attribute to indicate whether the above list is a not enforced list
# or an enforced list; When the value is true, the list means enforced list,
# or in other words, the whole web site is open/accessible without
# authentication except for those URLs in the list.
com.sun.am.policy.agents.config.notenforced_list.invert = false
# Not enforced client IP address list is a list of client IP addresses.
# No authentication and authorization are required for the requests coming
# from these client IP addresses. The IP address must be in the form of
# eg: 192.168.12.2 1.1.1.1
com.sun.am.policy.agents.config.notenforced_client_ip_list =
# Enable POST data preservation; By default it is set to false
com.sun.am.policy.agents.config.postdata.preserve.enable = false
# POST data preservation : POST cache entry lifetime in minutes,
# After the specified interval, the entry will be dropped
com.sun.am.policy.agents.config.postcache.entry.lifetime = 10
# Cross-Domain Single Sign On URL
# Is CDSSO enabled.
com.sun.am.policy.agents.config.cdsso.enable=false
# This is the URL the user will be redirected to for authentication
# in a CDSSO Scenario.
com.sun.am.policy.agents.config.cdcservlet.url =
# Enable/Disable client IP address validation. This validate
# will check if the subsequent browser requests come from the
# same ip address that the SSO token is initially issued against
com.sun.am.policy.agents.config.client_ip_validation.enable = false
# Below properties are used to define cookie prefix and cookie max age
com.sun.am.policy.agents.config.profile.attribute.cookie.prefix = HTTP_
com.sun.am.policy.agents.config.profile.attribute.cookie.maxage = 300
# Logout URL - application's Logout URL.
# This URL is not enforced by policy.
# if set, agent will intercept this URL and destroy the user's session,
# if any. The application's logout URL will be allowed whether or not
# the session destroy is successful.
com.sun.am.policy.agents.config.logout.url=
#http://sportal.yjy.dqyt.petrochina/amserver/UI/Logout
# Any cookies to be reset upon logout in the same format as cookie_reset_list
com.sun.am.policy.agents.config.logout.cookie.reset.list =
# By default, when a policy decision for a resource is needed,
# agent gets and caches the policy decision of the resource and
# all resource from the root of the resource down, from the Access Manager.
# For example, if the resource is http://host/a/b/c, the the root of the
# resource is http://host/. This is because more resources from the
# same path are likely to be accessed subsequently.
# However this may take a long time the first time if there
# are many many policies defined under the root resource.
# To have agent get and cache the policy decision for the resource only,
# set the following property to false.
com.sun.am.policy.am.fetch_from_root_resource = true
# Whether to get the client's hostname through DNS reverse lookup for use
# in policy evaluation.
# It is true by default, if the property does not exist or if it is
# any value other than false.
com.sun.am.policy.agents.config.get_client_host_name = false
# The following property is to enable native encoding of
# ldap header attributes forwarded by agents. If set to true
# agent will encode the ldap header value in the default
# encoding of OS locale. If set to false ldap header values
# will be encoded in UTF-8
com.sun.am.policy.agents.config.convert_mbyte.enable = false
#When the not enforced list or policy has a wildcard '*' character, agent
#strips the path info from the request URI and uses the resulting request
#URI to check against the not enforced list or policy instead of the entire
#request URI, in order to prevent someone from getting access to any URI by
#simply appending the matching pattern in the policy or not enforced list.
#For example, if the not enforced list has the value http://host/*.gif,
#stripping the path info from the request URI will prevent someone from
#getting access to http://host/index.html by using the URL http://host/index.html?hack.gif.
#However when a web server (for exmample apache) is configured to be a reverse
#proxy server for a J2EE application server, path info is interpreted in a different
#manner since it maps to a resource on the proxy instead of the app server.
#This prevents the not enforced list or policy from being applied to part of
#the URI below the app serverpath if there is a wildcard character. For example,
#if the not enforced list has value http://host/webapp/servcontext/* and the
#request URL is http://host/webapp/servcontext/example.jsp the path info
#is /servcontext/example.jsp and the resulting request URL with path info stripped
#is http://host/webapp, which will not match the not enforced list. By setting the
#following property to true, the path info will not be stripped from the request URL
#even if there is a wild character in the not enforced list or policy.
#Be aware though that if this is set to true there should be nothing following the
#wildcard character '*' in the not enforced list or policy, or the
#security loophole described above may occur.
com.sun.am.policy.agents.config.ignore_path_info = false
# Override the request url given by the web server with
# the protocol, host or port of the agent's uri specified in
# the com.sun.am.policy.agents.agenturiprefix property.
# These may be needed if the agent is sitting behind a ssl off-loader,
# load balancer, or proxy, and either the protocol (HTTP scheme),
# hostname, or port of the machine in front of agent which users go through
# is different from the agent's protocol, host or port.
com.sun.am.policy.agents.config.override_protocol =
com.sun.am.policy.agents.config.override_host =
com.sun.am.policy.agents.config.override_port =
# Override the notification url in the same way as other request urls.
# Set this to true if any one of the override properties above is true,
# and if the notification url is coming through the proxy or load balancer
# in the same way as other request url's.
com.sun.am.policy.agents.config.override_notification.url =
# The following property defines how long to wait in attempting
# to connect to an Access Manager AUTH server.
# The default value is 2 seconds. This value needs to be increased
# when receiving the error "unable to find active Access Manager Auth server"
com.sun.am.policy.agents.config.connection_timeout =
# Time in milliseconds the agent will wait to receive the
# response from Access Manager. After the timeout, the connection
# will be drop.
# A value of 0 means that the agent will wait until receiving the response.
# WARNING: Invalid value for this property can result in
# the resources becoming inaccessible.
com.sun.am.receive_timeout = 0
# The three following properties are for IIS6 agent only.
# The two first properties allow to set a username and password that will be
# used by the authentication filter to pass the Windows challenge when the Basic
# Authentication option is selected in Microsoft IIS 6.0. The authentication
# filter is named amiis6auth.dll and is located in
# Agent_installation_directory/iis6/bin. It must be installed manually on
# the web site ("ISAPI Filters" tab in the properties of the web site).
# It must also be uninstalled manually when unintalling the agent.
# The last property defines the full path for the authentication filter log file.
com.sun.am.policy.agents.config.iis6.basicAuthentication.username =
com.sun.am.policy.agents.config.iis6.basicAuthentication.password =
com.sun.am.policy.agents.config.iis6.basicAuthentication.logFile = c:/Sun/Access_Manager/Agents/2.2/debug/C__Lotus_Domino/amAuthFilter

Hi,
I installed opensso (so Sun Java(TM) System Access Manager 7.5) and the agent for Domino 6.5.4 and I have the message in logs "amAgent"
2007-07-11 18:40:16.119 Error 1708:3dbcf768 PolicyAgent: render_response(): Entered.
I have the box to identify but it doesnot connect me on my opensso server.
It still identify with Domino's server
Thanks for your response
Thomas

New major release of Sun Storage 7000 software is available

I noticed a new major release of the Sun Storage 7000 software is available at the website below.
http://wikis.sun.com/display/FishWorks/Sun+Storage+7000+Series+Software+Updates.

The format change is for BDB Java Edition 5.0 only, and does not apply to other BDB products. It's forward compatible, which means that a BDB JE application using JE 5.0 can use environments written with older versions of JE. However, it's not backwards compatible; once your environment has been opened by JE 5.0, it's been converted to the new format, and can no longer be readable by older versions of JE.
Just for the benefit of others who may not have read the changelog, here's the full text:
JE 5.0.34 has moved to on-disk file format 8.
The change is forward compatible in that JE files created with release 4.1 and earlier can be read when opened with JE 5.0.34. The change is not backward compatible in that files created with JE 5.0 cannot be read by earlier releases. Note that if an existing environment is opened read/write, a new log file is written by JE 5.0 and the environment can no longer be read by earlier releases.
There are two important notes about the file format change.
The file format change enabled significant improvements in the operation performance, memory and disk footprint, and concurrency of databases with duplicate keys. Environments which contain databases with duplicate keys must run an upgrade utility before opening an environment with this release. See the Performance section for more information.
An application which uses JE replication may not upgrade directly from JE 4.0 to JE 5.0. Instead, the upgrade must be done from JE 4.0 to JE 4.1 and then to JE 5.0. Applications already at JE 4.1 are not affected. Upgrade guidance can be found in the new chapter, "Upgrading a JE Replication Group", in the "Getting Started with BDB JE High Availability" guide.I may not have fully understood your question, so let us know if that doesn't answer it.
Edited by: Linda Lee on Dec 1, 2011 10:41 AM

PowerBook Can't Run Airport Management Utility

I'm still trying to find out why my PowerBook can't run Airport Management Utility, even though all of my other Airport software is up to date. When I try to launch the utility, it gives the message that it "requires Airport 3.4 or later", which I do already have.
Below is a description of my latest effort, followed by my original question, which has been archived in this discussion group.
I created and logged in via a new user account, but I still got the same 'requires Airport 3.4 or later' message from Airport Management Utility. I took it from this that the problem was not related to user preferences.
I then used Spotlight to search the Library folder. The only airport pref I found there was com.apple.airport.preferences.plist, located in this path: Macintosh HD/Library/Preferences/SystemConfiguration.
The computer would not let me move this to the desktop, but copied it instead. I can open that copy in TextEdit, but if I double click on it, it actually launches in OmniOutlner. A check via "Get Info" shows that it is set to "Open with: OmniOutliner" from the drop down menu in the Get Info box.
If you open this plist in OmiOutliner, you find the information I've listed below. It appears to show that the file does know the Airport software version is "5" and not less than 3.4:
• Disconnect on logout 0
• AllowEnable 0
▶ Default 802.1X Configurations
• InterferenceRobustness 0
• Require Admin for network 0
change
• JoinMode 1
• Always remember new networks 1
▶ List of known networks
• Version 5
• Require Admin for IBSS creation 1
• Fallback Preference 0
The only other items in the Library folder with "airport" in the name are both in the Receipts folder: AirportTI2005-001.pkg and AirportConfigApps.pkg.
I'd welcome your thoughts on this.
My original posting was:
I have the newest PowerBook G4 , purchased this fall with Mac OS X 10.4.3 and AirPort Update 2005-001 installed.
When I try to run Airport Management utility I get the message : " "The Airport Management Utility requires Airport 3.4 or later. Click Update to check for newer software." While Airport Management Utility will not run on my PowerBook, it does run on my iMac with 10.3.9.
I've tried:
-installing "AirPort Update 2005-001" but it didn't solve the problem.
-installing "AirPort 4.2 for Mac OS X 10.4.2", thinking that if it were not needed, the installer would not run. It did install, but that did not solve the problem.
-re-installing "AirPort Update 2005-001", which did install a second time, but did not solve the problem. (I thought perhaps the installer for this update wouldn't run a second time.)
Does anyone know of a solution, or does Apple need to update Airport Management Utility?
(I've cross-posted this in the Airport discussion area, but I also wanted to check with others who recently bought the same PowerBook.)
Thanks for your help.
PowerBook G4 (Double-Layer SD) 15-inch, iMac (1GHz 17-inch) Mac OS X (10.4.6)

check this link:
http://discussions.apple.com/thread.jspa?messageID=2265548#2265548
Teh-Way Lee wrote:
"OK, I've been following this thread since February and I think I got this thing figured out. Joseph Jordan pointed to the right direction and I did some more digging.
I had the same problem as most posters here:
- ALL 10.3 machines had AirPort Management Utility working but,
- NOT ALL 10.4 machines had AirPort Management Utility working.
In my case, no 10.4 computer had AMU working (updated from 10.3 or fresh install of 10.4, Intel or PowerPC, even brand new MacBook Pro and PowerBook G4 out of the box), EXCEPT one xserve that was updated from 10.3.
As I said before, Joseph Jordan pointed to the right direction, the file/folder AirPortConfig.framework in /System/Library/PrivateFrameworks/ is missing.
It seems that AirPortConfig.framework was installed when AirPort 4.1 was installed. AirPort 4.2 installs Apple80211.framework only. I think...
In some cases, AirPortConfig.framework is there (updated machines), but the file AirPortConfig is missing in AirPortConfig.framework/Versions/A/
as well as the symbolic links to it and to other folders.
Solution:
The easiest way is to copy the whole AirPortConfig.framework to /System/Library/PrivateFrameworks/
If you already have AirPortConfig.framework and AMU is not working, move it to the trash or somewhere else.
I found AirPortConfig.framework in the "AirPort Extreme Software Installation" CD (CD version 4.1 2Z691-5219-A):
1. Open the CD
2. Control-click "AirPort for Mac OX X v10.3" and select Show original
3. Control-click "AirPortSW.pkg" and select Show Package Contents
4. Open Contents
5. Drag Archive.pax.gz to the Desktop
6. Double-click Archive.pax.gz to unarchive the file
7. AirPortConfig.framework is in ~/Desktop/Archive/System/Library/PrivateFrameworks
8. Drag AirPortConfig.framework to /System/Library/PrivateFrameworks/ You will be asked to authenticate.
AMU should work at this point.
Alternatively, download "AirPort 4.1 Update.dmg" from
http://www.apple.com/support/downloads/airport41formacosx.html
and follow from step 3. above.
This solution seems to work on both Intel and PowerPC machines.
Computers tested: Power Mac G5, Powerbook G4 12" and 17", MacBook Pro.
IMPORTANT: I do not know if this solution breaks anything. CAVEAT EMPTOR!"
PowerBook G4 (Double-Layer SD) 15-inch, iMac (1GHz 17-inch) Mac OS X (10.4.6)

MMC with Computer Management Utility & Sun Storage 7110 in CIFS ?

Similar Messages

Maybe you are looking for