Mobile Barton XP2400+ Overclock on K7N2 Update

For Whoever's Interested -
Couldn't get >2000mHz with my mobile Barton XP2400+. Proceded as follows:
1. Went to http://www.arcticsilver.com and read instructions for proper application of Arctic Ceramique. I know there's some people laughing !
2. Reinstalled Vantec CCK-6040H heatsink/fan after applying ceramique per Arctic Silver's instructions.
3. Also noticed the CPU RTD was pushed down touching the board, so, lifted it up to touch bottom of cpu.
4. Rebooted into Windoze; cpu temp 39C at idle via MBM.
5. Incrementally increased Vcore from 1.55 to 1.625 (in steps), rebooting, and looking at temps.
6. Raised multiplier to (8x) 16x with Vcore at 1.625. Booted fine. Ran some apps. Good. Temp 46C immediately after Win98 load and decreased to 41C at low load/idle.
7. Raised multi to (9x) 17x w/ Vcore still at 1.625. Booted. Received BSOD while loading Win98.
8. Raised Vcore to 1.650 and booted with 17x multi. Temp 50C immediately after loading Win 98. Now 40-43C as I write this.
Guarded optimism ! Still need to run Memtest86 to verify stability.
Why does the cpu temp rise so dramatically when in bios and right after OS load ?
Mark

When I 1st installed the mobile Barton (Monday) with no wire trick; I set the multi to 9x in bios and posted at 9x133fsb. I made it up to 12.5x133fsb (a bit over 1662mHz). A 13x multi posted at 600mHz !
So, removed the cpu, installed the wire jumper, and reinstalled the mobile Barton. I then booted with a 9x multi and it posted at 2261mHz, but, crashed. I then dropped the multi down to 7x and have been running at 2000mHz until reinstalling the heatsink/fan with Arctic Ceramique properly applied. Now running with a 9x multi. WCPUID reports a 17x multi and 2271mHz as does cat /proc/cpuinfo in linux.
So, maybe I'm misunderstanding, but, I did need the wire trick for the mobile Barton - its multi is factory set at 6.
Mark

Similar Messages

Bios for K7n2 delta 2 LSR (2800+ Mobile Barton Recognizing)

Hi, i need the BIOS for the Bios for MSI K7n2 delta 2 LSR Motherboard, because i have a Mobile Barton 2800+ CPU with FSB 266 and it isn't recognized correct, i would like to set the Multiplier to 16, the highest setting is 13 - but at 13 my system didnt boot anymore. I tried the B72 Bios, but it didn't help. Thanks

What's that? You already asked for that in another thread (https://forum-en.msi.com/index.php?topic=123557.msg932826#msg932826). Please don't open various threads for the same issue.
I already said in the other thread you can't set 16 manually. Set it to auto.

KT266 Pro2-RU + mobile barton XP2500+M

There's been a lot on this forum about the modded bios etc which enables the 6380 v2 motherboard to be compatible with the later T'bred and thornton chips.
But searching through the maze of users' comments I've failed to locate anything saying that it is also compatible with the Barton chip, specifically the mobile Barton chips.
I currently use a 2 year old Thunderbird 1200mhz chip, and would like to upgrade to a Barton 2500+ mobile chip, as it's the only 266mhz Barton chip I can find in the UK. I assume that I cannot use a 333fsb chip on my mobile, unless it is unlocked an I can move the multiplier high enough?
I am utterly confused with the products that AMD have on offer. Is there anywhere where their performances have been compared? Is a T'bred 2500+ significanly slower than a Barton 2500+ because of the 512kb L2 cache?
Cheers

Hi all for again,
I have K7T 266Pro2 - RU (MS-6380)
What is the max speed of processor/fastest procesor, which can I safely use? - I would like stable system too - I want NOT using overclocking...
1) If I make all mods to work with Thoroughbred (update to BIOS 3.7, remove C37), it will work with Thorton?
2) What is the max configuration (speed) with K7T 266 Pro2 - RU? I read much in this forum, but I'am very foggy. Is it 133 * 15 or 133 * 17.5 (with set auto in BIOS or HOW?)
What is the max configuration without doing some special mods (e.g. on processor) only with changing settings in BIOS and with removed C37?
What is the best and fastest choice of processor?
Many thanks for any advice and very sorry for my very poor english.

KT3Ultra and Mobile Athlon XP2400+ possible?

HELP!!!
I just purchased a mobile Athlon XP2400+ for use on my MSI KT3Ultra (via KT333)
and I would like to
A) Get it to work on my board
B) Overclock it
What type of settings should I use? I currently run an XP2100+ Polly stock. Can I leave the stock 1.73 (or 1.65 cant remember) voltage, and increase FSB to 166, ot what?
Am using Crucial PC3200 (512 MB), GF4 Ti 4200 128Meg........
HELP!!!

u prolly wont need this but look here:
https://forum-en.msi.com/index.php?threadid=38822&sid=
make a true sig, amps on psu, an mobile athlon probabley will work
as for overclocking "RESEARCH" its best to see what others have done, and what they have achieved, and how to go about doing it, look at the overclcoking guide at the top of the forum

The next mobile barton

ok....i think everybody in this forum knows the famous AMD Athlon XP-M 2500/2600 which could overclock to 2.2-2.6Ghz
now my question to all you fellow oc'ers is
which is the next mobile barton in the Athlon64s?
i want to go for the cheapest best overclockable 939 chip.....
one consideration is the Athlon64 3000+ 939 Venice core with E3 revision which oc's from 1.8Ghz to 2.4Ghz
anything else
thx ppl

Quote from: Codename47 on 22-February-06, 14:39:16
lets not fight over that......
i want to know how mem rates differ on different mobos when the memory controller is in the amd64 itself......
they shouldn't. but even if they do, it doesn't matter too much since you wouldn't notice the difference. anyway. lets say u get a foxcon, which doesn't have the oc-ing potential of a MSI or DFI, and one of the MSI or DFI mobos. you will be able to overclock more with the MSI and DFI than with the foxcon, so in the end, your system will end up a lot faster. if you are really set on memory rates, you can go with the DFI, since it has a 3.4V memory voltage and also you can use the mushkin red series or the OCZ memory at their full potential on that mobo. and trust me, it will beat the living s%#t out of the foxcon.
with the price, well, you get what you pay for. the MSI and DFI mobos are the best ones around, and i still have to see a producer that will beat this two companies in performance (at least for socket 939 mobos)

Can't remove apple mobile device support. need to for update?

Every time I plug in my iPhone (3GS or my wife's 4) or my iPad2 I get a message telling me to update Apple mobile devise support and to do so I need to uninstall it and iTunes and reinstall.
Windows won't uninstall AMDS. (windows vista)
It will uninstall everytihng else but AMDS give me a rolling back actions and failed to uninstall due to "fatal errors durring installation".
Is there a way I can get around this to update it? Or do I have to fix these errors and get it uninstalled?
only started happening since most recent update of iTunes and iOS 6 on both phones and iPad. iPod classic still plugs in and syncs fine.

Well, after some virus scanning, spybot destroying, and trying to make a new windows user to remove it: still no progress.
next on the list is cleaning registry and disk defrag (even though I don't think it will help).
Very much open to any suggestions so I don't have to actually take my system somewhere and have to pay someone to fix such a silly thing.
Don't know why it doesn't just update itself when iTunes does....

MOVED: Z68A-GD65 (G3) - can't overclock after BIOS update

This topic has been moved to Overclocking, Undervolting.
https://forum-en.msi.com/index.php?topic=252819.0

Quote from: JLio01 on 29-January-15, 13:54:12
What does ME version show under BIOS currently? When you check the ratio under OS, do you put your system under loading? And did you re-install driver from website after updating BIOS?
http://www.msi.com/support/mb/Z68AGD65_G3.html#support_download
ME version 8.1.2.1318. Even if I put the system at 100% load in Windows, the processor never moves past 3.4 GHz. I've checked this in multiple programs (CPUZ, RealTemp, TMonitor, etc.) And yes, I reinstalled the drivers that were listed under the BIOS update.
Quote from: TZBC on 29-January-15, 14:17:52
Go to OC section and change to advanced mode, change your CPU Ratio Mode from Dynamic to Fixed mode.
And go to windows checking the ratio have changed or not.
EDIT: sorry, I forgot this motherboard doesn't have this settings, try Disabled or Enable "Adjust CPU Ratio in OS"
I've tried changing that setting (Adjust CPU Ratio in OS) but it doesn't seem to have any effect.
However, I just noticed that I didn't have the newest version of CPUZ. I updated it and now it shows more detailed information for the multiplier: x34 (16-44)
So it is detecting that I have set it to 44 in Windows after all. But it seems to be indicating that it's using a dynamic CPU ratio of 16-44 - which I don't want, I want it fixed at 44 - but as you say, there's no option for dynamic/fixed on my motherboard. However, on the old v23.7 BIOS, if I set it to 44 it stayed at 44 always.
Even if it's using a dynamic ratio for some reason, it's not doing that right either because it's still never moving past 3.4 GHz (nor is it ever dropping below 3.4 GHz).

Mobile Hotspot Issue after 10.1 Update

Hello, just wondering if there is a know issue with using mobile Hotspot after update z10 to 10.1. After this update was installed Mobile Hotspot will turn on but past network that I had created is not there anymore, also I cannot configure, when I press configure nothing happens, and then Mobile Hotspot turns itself off.

Hello dnivek,
Welcome to the forums.
I would suggest you contact your mobile service provider to ensure you are on the correct data plan to allow you to use the Mobile Hotspot feature. If they confirm you are on the correct plan and have the correct APN settings then please have them escalate your issue to BlackBerry Technical support for investigation.
-SR
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Can't access the Internet via Mobile Data & Wifi after IOS 6 update.

Hi Hi,
Are facing the same problem that I'm facing? After updating the iOS 6 my ipad2 can't access to the Internet vai both data and wifi.
I event tried activity my iPhone 4S hotspot to allow my IPad2 to connect and is not working too.

Hi Ralph,
Thanks for the advice and tips. The wifi problem has been sovled by not on the mobile data.
When I'm using the mobile date to access the network it will not work. I have tried to rebooth, tuning the mobile data option and the data roaming on and off. Still does't not work.

"Can't activate mobile datanetwork" after OS 3.0 update

After updating my 3G (not jailbroken, not unlocked)to the 3.0, I can't get a connection through APN.
I get the message: "Can't activate mobile data network"; although my APN settings are correct.
Wifi works fine.
Anyone?

it could be that the dock connector is not setup to work with the 3.0 update. have you checked the manufacturer to see if they have an update of some kind?

Mobile data not working after lollipop update

Hi. On my z2 mobile data doesn't work at all. I've update to lollipop yesterday and since then nothing. Tried factory reset, repair wit pcc, get internet setting from settings-more-internet connection, simply nothong. Can u help me pls....

i got sim card from my carrier and did not do with it anything. just inserted to phone. so it´s not helpfull. i downgrade to 4.4.4 kitkat and mobile data working as used to. so... what now? What are the odds that simcard stop working properly after upgrade to lollipop and start working after downgrade to kitkat?

Help, can't overclock after bios update!

On the stock k9n2 750a bios version, my AMD 5400 OC’ed to a stable 3.08ghz without any hassle by simply setting the FSB to 220mhz . Recently, I flashed to the AMI 7374 v3.5 bios and couldn’t even post after bumping the FSB to 202mhz (it’s fine @200mhz). So, I reverted the bios back to AMI 7374 v3.1 and for some reason it now can’t post either after saving a FSB above 200mhz . As far as I can remember, I’m using the same settings as I used when I got the stable 220mhz FSB.
Anyone know what the bios update did to kill my overclocking or got some ideas/advice on how to get back to the stable 220mhz FSB? Thanks.

Quote from: JLio01 on 29-January-15, 13:54:12
What does ME version show under BIOS currently? When you check the ratio under OS, do you put your system under loading? And did you re-install driver from website after updating BIOS?
http://www.msi.com/support/mb/Z68AGD65_G3.html#support_download
ME version 8.1.2.1318. Even if I put the system at 100% load in Windows, the processor never moves past 3.4 GHz. I've checked this in multiple programs (CPUZ, RealTemp, TMonitor, etc.) And yes, I reinstalled the drivers that were listed under the BIOS update.
Quote from: TZBC on 29-January-15, 14:17:52
Go to OC section and change to advanced mode, change your CPU Ratio Mode from Dynamic to Fixed mode.
And go to windows checking the ratio have changed or not.
EDIT: sorry, I forgot this motherboard doesn't have this settings, try Disabled or Enable "Adjust CPU Ratio in OS"
I've tried changing that setting (Adjust CPU Ratio in OS) but it doesn't seem to have any effect.
However, I just noticed that I didn't have the newest version of CPUZ. I updated it and now it shows more detailed information for the multiplier: x34 (16-44)
So it is detecting that I have set it to 44 in Windows after all. But it seems to be indicating that it's using a dynamic CPU ratio of 16-44 - which I don't want, I want it fixed at 44 - but as you say, there's no option for dynamic/fixed on my motherboard. However, on the old v23.7 BIOS, if I set it to 44 it stayed at 44 always.
Even if it's using a dynamic ratio for some reason, it's not doing that right either because it's still never moving past 3.4 GHz (nor is it ever dropping below 3.4 GHz).

Can't overclock a K7N2 Delta2 LSR?

I have the K7N2 Delta2 LSR v1.0 board with 3GB of PC2700 memory and Athlon XP 3200+ processor. The PSU is a Antec 400w.
I have tried several different overclocking methods, and none seem to work. The D.O.T. didn't work at all, not even in Private mode. The computer hangs when it gets into Windows. I tried just increasing the FSB to 202MHz with the memory on "Optimal", and Windows still hangs. Am I doing something wrong, or does this processor just not want to go any faster?
Bryan

The nforce2 chipset likes the memory controller and the CPU FSB clock to run at the same speed.
So by increasing the FSB to 202mhz, you're also increasing the DDR clock to 202mhz (which equals DDR404). As your memory is only rated as DDR333, its no wonder its failing.
Athlon XP3200+... which one, the 333FSB or 400FSB version?
Also, as you are running 3GB, also be aware that best performance is gained from using just two identical matched sticks in dual-channel mode.

Mobility Radeon 4670 overclock help

Hi , I received my MSI GX623 laptop the other day and decided to try and overclock the video card. To my surprise , no overclocking utilities I tried were able to change the clocks (Riva Tuner, AMD GPU Clock Tool and others which I already forgot :P). The video card is mobility radeon 4670 512MB DDR3. I want to squeeze out the last drop of performance out of this laptop so please give me some advice on how to break this clock lock.

Okay, I'm re-newing this thread due to new findings.
After some tough experimentation I've finally figured out how to f#@king overclock those damn mobility chips HD4650/4670 in some of those also damned HP possibly SONY, ASUS, and MSI laptops in which they are used.
It all comes down to the device ID in the RivaTuner config file named "RivaTuner.cfg" all you have to do, is to check your device ID and add it to the list of RV730 devices listed in there with a *h-suffix.
I've done the modification on mine, {not naming the model, though it should be clear from the above post} and its safe to say its running perfectly on increased clocks without as much as an extra degree Celsius or increased fan speed. Make sure you enter the right ID or else it won't work, in my case being 9480h, its so damn trivial that it makes me mad!
Been testing it for quite a while, extensively, with all sorts of apps., games, and most of all 24/7 GPU crunching ^^
I just despise those lame comments from folks all over the web that notebook O/C, be it CPU or GPU is unwise / unsafe, screw their opinion, being an enthusiast for over 7 years and never having a burned / broken hardware due to voltage / thermal loads should be a proof by itself, I say, PUSH it as HARD as you can!
Darn, I hope this is gonna finally help all those that were looking for their HD4000 series overclock issue to be solved, I certainly was looking and monitoring the progress for over 3 months now and grew tired of it!
feedbacks welcome...
Cheers!

My iPhone 3gs was locked to virgin but it was unlocked before i bought it and i now use a t-mobile sim card. If I update my phone to ios 5.1 will it lock my phone so I can no longer use it? I'm scared to update!! Please help

I updated my sisters phone yesterday to ios 5.1 but after I did this it wouldn't recognise her sim card and the phone isn't unlocked or jailbroken. My phone is unlocked but not jailbroken and I have done all the updates before without a problem. Does this mean that if I update to ios 5.1 it wont lock my phone and will continue to work as normal?

That depends on where it came from and how it was "unlocked". Virgin is a supported carrier in France and in Canada.
If you are in France, then it could have been legitimately unlocked. Virgin France offers unlocking.
If you are in Canada, then it was definitely hacked to unlock it as they do not offer unlocking there. If it is a Canadian phone, you can't be supported here at all. Discussing hacked and jailbroken phones is forbidden by the terms of service.

Mobile Barton XP2400+ Overclock on K7N2 Update

Similar Messages

Maybe you are looking for