Mobile Module for Labview 2009

Hello,
What do I need to install to use Mobile Module with Labview 2009?
I have installed Labview 2009 but I don't see the PDA icon on the main page.

I have seen this link, but it doesn't say what I need to check when installing Labview 2009 SP1 in order to get the Mobile Module.
I work at The University of Twente and we have a full license, so I'm sure it has to be at the install checkbox somewhere...

Similar Messages

Installing 64 bit version of toolkit and modules for Labview 2009 64 bit?

Hello I recently contacted NIabout installing Mathscript and Signal processing toolkits for my Labview 200964 bit that I am running on Windows 7. I was sent the following link as aresponse: http://zone.ni.com/devzone/cda/tut/p/id/10383. From this link it is my understanding that I cannot run any programs thatcontain an astrestik, since they only work for 32 bit version of Labview? In particular I really need to use Mathscript. Is there any workarounds? Do I have to also install the Labview 2009 32 bit version? Doesanyone know when Labview will allow me to run everything in the 64 bit versionof Labview? Thanks.
Kevin

Hello Kevin,
There is no workaround available, and there are no released dates as to if/when Windows 7 x64 support for the toolkits in question will be introduced.
The LabVIEW Mathscript RT Module is not supported in LabVIEW 64-bit as mentioned at the bottom of the following page: http://zone.ni.com/reference/en-XX/help/371361F-01/lvhowto/labview_mathscript/ .
Vivek Nath
National Instruments
Applications Engineer
Machine Vision

Quanser DC Motor Control Trainer missing VI's for labview 2009

Hi my name is phillip, a student developer working with labview 2009 and the Quanser DC Motor Control trainer with ELVIS II. I have failed to run the VI for speed control, it appears to be broken and says four sub-vi's are missing and they are "Intergrator.VI," "Integrator (DBL).VI," "Transfer Function.VI," "and "Transfer Function (DBL).VI.". I happen to have installed the control design and simulation toolkit but this has not solved the problem. Please help!!!!

Hi Phillk, I have the exact same problem with the missing VIs for the Quanser DC motor control with the NIELVIS also for Labview 2009.
Can you please tell me where I can find these VIs? Can you send them to me if it is possible?
I would really appreciate it,
I need the Transfer Function.vi, Transfer Function (DBL).vi and the integrators too.
Thank you,
Carlos M. Rodriguez
[email protected]

DSP Module For LabVIEW 2011

Dears,
I need the DSP Module For LabVIEW 2011, is it Available? and where can I Download it ?
Thanks
Ahmed Abdulbaky

Hi Ahmed,
I posted this in error. I did not see that Ryan had already answered this.
Ryan is correct. The latest version is 8.6
You can download the latest version of the DSP module from ni.com/downloads. The exact URL is shown below:
http://search.ni.com/nisearch/app/main/p/bot/no/ap/tech/lang/en/pg/1/sn/ssnavdl/q/dsp/#
I hope this information helps.
Regards,
James D.
Applications Engineer
National Instruments

Xantrex HPD driver for LabVIEW 2009

I've seen there are other NI products that have drivers for the Xantrex HPD power supplies.
Does anyone have one that works for LabVIEW 2009 (or earlier)?
Solved!
Go to Solution.

OK. Got it.
Hyperterminal worked.
It verified that port settings and command syntax was correct.
ALL the programs in the LabVIEW examples don't get the CR function to the power supply. When I hard coded the CR function following the command (also hard coded) it worked. Xantrex (now Sorensen) manuals include NO simple examples - one just has to know from experience (catch 22) how to do it.
Of note also is that one must send a both voltage and current setting commands as both are zero by default. (If you send only one, nothing APPEARS to happen because the other is set to 0.) That also could have been included in a beginning example.
<end of rant>
THANKS for your help!

What is the differrence between NI motion asst and motion dev module for labview?

Hi,
Could you please tell me the difference between Ni motion assistant and soft Motion development module for LabVIEW also the application areas of both.
Thanx
Mukesh

Hello Mukesh,
Do you mean the SoftMotion Development Module for LabVIEW? FlexMotion and SoftMotion are two totally different methods of creating a motion system. FlexMotion uses a motion controller board (PCI or PXI). The software interfaces with the board. On the board there is a lot of processing that is done (ie: PID control). The board interfaces with the motion drive. In a SoftMotion system, there is no motion controller board. You need to use some other I/O technology (ie: DAQ, FieldPoint, RIO, etc) to interface directly from the software to the motion drive. All of the processing that was done on the motion controller is now done in the software.
So FlexMotion is an API to help your software interface with a motion controller board. SoftMotion is an API that enables your software to process data in a motion system (ie: process it the way that a motion controller would).
Motion Assistant is an application environment (separate from LabVIEW) that allows you to set up a sequence motion commands through dialog boxes. You can set up a motion process and test it in Motion Assistant. It is capable of building LabVIEW code for the same motion system. There is also an API that allows you to control Motion Assistant from LabVIEW programmatically.
I hope this information helps. Please let me know if you have any further questions about this issue. Take care!
Regards,
Aaron B.
National Instruments

Parche labview 2009(patch for LabView 2009)

Estimados:
He instalado LabView 2009 con los módulos RealTIme y MathScript RT. A pesar de haber instalado los parches (Patch) recomendados tengo muchos problemas de inestabilidad del software.
He instalado el parche "LVRT2009f2" y el "NIDAQ900f2" para RealTim. Estoy trabajando con un Desktop Target y un Host.
El problema :
Se cuelga y se cierra Labview (a veces,esporádicamente) al intentar grabar el proyecto o al descargarle el programa al Target.
Desde ya ,gracias por su ayuda.
Saludos

Translation
I installed 2009 with LabView modules and MathScript RealTime RT. Despite having installed the patch (Patch) recommended I have many problems of instability of the software.
I installed the patch LVRT2009f2 "and" NIDAQ900f2 "to realtime. I'm working with a Target and Host Desktop.
The problem:
* It hangs and closes Labview (sometimes sporadically) while attempting to burn the project or downloaded it for at Target.

Newport Conex-CC drivers for LabVIEW 2009

Dear all;
I am using LabVIEW 2009 on Windows 7. I need the drivers for the Newport Conex-CC controller. They are available in the web site http://www.newport.com/CONEX-CC-DC-Servo-Controller-Actuators/934114/1033/info.aspx#tab_Literature , but the version is LabVIEW 2010, so I can`t open them.
Please, could anybody open the .vi's, save them as LabVIEW 2009 or older, and attach them to a reply message?
Thank you.
Javier

Please post the VIs to the Version Conversion board. The link is at the top of the LabVIEW board.

HP 6629A Driver for Labview 2009 may have a bug?

6629A config output.vi that came with the driver may have a bug. I am pretty new to labview so maybe I am incorrect, but the current range boolean was not wired to the T/F select block with the current limits for the instrument in high current and low current mode. Instead the voltage range boolean was wired to that block. Maybe I don't understand the operation of the instrument fully, but this seems like a mistake to me. Any comments/help would be appreciated.

Well, I already kind of fixed my version of it. I will post that for now. If you want I can post the original version of the vi that came with it when I downloaded the drivers. The vi in question is called '6629A Config Output.vi'
This is a link to the operating manual for the instrument:
http://www.home.agilent.com/agilent/editorial.jspx?cc=GB&lc=eng&ckey=1000000433:epsg:man&nid=-11143....
I hope that is what you needed.
Thanks for looking into this.
Attachments:
HP662XA.LLB ‏509 KB

Incoherence parallelisme boucle for - LabView 2009

Bonjour,
en faisant un test pour estimer le gain a attendre de la parallelisation des boucles for, je suis tombe sur un resultat curieux. La modification du diagramme sur un detail, a priori independant de la boucle for, induit des variations de temps de calcul allant de -56% a +47% de facon tout a fait reproductible. (voir ppt joint)
A noter (en configuration +47%) qu'en bloquant le nombre de processeurs logiques (P) a 1 on obtient un leger gain de -13% (sans ecart dans les calculs) et si P est a 2, on a -32% (avec ecart dans le calcul pour tous les autres ce qui est logique) , P=3 => -30% , P=4 => -41.5%, P=5 => -41.7% qui ne bouge plus en augmentant.
En configuration -56% le bloquage de P induit une perte de perforamances entre P=2 =>-16%, P=3 =>+20%, P=4 => -20% ...
Quelqu'un pourrait il confirmer ces resultats sur une autre machine ou aurrait l'idee d'une erreur que j'aurais pu commettre ?
Merci d'avance
- Lionel -
Attachments:
Labview_2009_parallelisme.ppt ‏651 KB
test_parallelism_02.vi ‏15 KB

French to English
Hello,
making a test to estimate the gains from parallelization of loops, I came upon a curious result. Changing the chart on a detail, a priori independent of the loop, induces changes in computing time ranging from -56% to +47% for quite reproducible. (see attached ppt)
Note (commonly 47%) than in blocking the number of logical processors (P) 1 we obtain a slight gain of -13% (without any spread in the calculation) and if P is a 2, a -32 % (with deviations in the calculation for all others that makes sense), P = 3 => -30%, P = 4 => -41.5%, P = 5 => -41.7% that does not move to increase.
In the configuration -56% blockade of P induces a loss of perforamances between P = 2 => -16%, P = 3 => 20%, P = 4 => -20% ...
Someone could confirm these results on another machine or aurra the idea of a mistake I have committed?
Thank you in advance

Agilent 33220a drivers for LabVIEW 2009

Hello,
aprox. 3 Weeks ago i downloaded a driver for the Agilent 33220A Waveform generator.
Well i lost that one and tried to download it again from here:
http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9066659CE034080020E748...
The Problem is that the downloaded File is 0kb of size.
Anyone else got this Problem? Maybe someone can tell me another download link.
Thanks!

Well i'm at home now and you are right, it works
It just would not work at the University.
Anyways tanks for your time!

Labview 2009 Module Mobile And Lego Mindstorms NXT

Hi
I've installed the mobile toolkit in labview 2009 but when I created a new mobile project I didn't find the NXT Programmings category on menu.....
are they not supported?
I would like to control my nxt with my PDA through bluetooth.
Thanks in advance for help

Hi,
which NXT software did you exacly installed? LabVIEW Module for LEGO MINDSTORMS NXT or LabVIEW Toolkit?
I would like to be sure to have corretcly understood: in a mobile project, the function palette of a VI under a PDA target does not have the NXT palette, correct?
Bye!
Licia

Where can I find FPGA replication tool (Set RIO Device Settings.vi) for LabVIEW 2013?

I just upgraded to LV2013SP1 and came across a VI that now is broken in my project: Set RIO Device Settings.vi (which is a part of RIOSystemReplication2009.zip). Apparently this happened in 2009 as well for a different VI in the same collection of tools (see Where-can-I-find-FPGA-replication-tool-for-labview-2009. I tried the mentioned VIs in this article but both of them are broken). Note that the Replication and Deployment (RAD) Utility does not seem to support the functionality that Set RIO Device Settings does, so I still need to use the old one.
Since the VI is password protected I cannot attempt to fix it. Might be something as simple as a type that changed...
Any help appreciated!
Rob
LV2011,LV2012,LV2013

Hey Rob,
This problem has already been brought to NI R&D's attention, and they are working on a fix under Corrective Action Request (CAR) 454468. Unfortunately, until they fix the problem there may not be a way to correct the problem in the near future. The CAR is set for higher priority, so a fix could come shortly.
Regards,
Ryan

Online LabVIEW 2009 help search function broken

the online help for LabVIEW 2009 has a search dialog, when I enter anything into that dialog and hit search on 'firefox 3.6' I get a page displayed by firefox that says that the results will take me nowher.
In internet explorer 8 I get a very long load time followed by an empty page.
Ton
Free Code Capture Tool! Version 2.1.3 with comments, web-upload, back-save and snippets!
Nederlandse LabVIEW user groep www.lvug.nl
My LabVIEW Ideas
LabVIEW, programming like it should be!

Fails in Google Chrome as well.
Ton
Free Code Capture Tool! Version 2.1.3 with comments, web-upload, back-save and snippets!
Nederlandse LabVIEW user groep www.lvug.nl
My LabVIEW Ideas
LabVIEW, programming like it should be!

LabVIEW 2009 causes CAD and other dongle programs to fail

Hi all,
I have just had a customer say that our LabVIEW 2009 application has stopped their CAD and other software with dongles from working.
Apparently it is due LabVIEW sharing the same (security?) port as something. They mentioned there was a LabVIEW patch?
They have been forced to remove our application.
What do we do?
Thanks.

Battler,
I did some looking into that Article you linked and found out that a few things have changed for LabVIEW 2009. For instance, I can not find those registry keys on my computer that the document suggests to change. Instead, Have you customer create the following directory:
For Windows XP: C:\Documents and Settings\All Users\Application Data\National Instruments\Logos
For Windows Vista: C:\ProgramData\National Instruments\Logos
In that directory have them make a file called Logos.ini. In that file have them place the following:
[logos]
Global.DisableLogos=True
Global.DisableLogosXT=False
This will disable the old logos service and make sure the new LogosXT service is running. This may be the LabVIEW 2009 equivalent fix of that document you sent me as it seems that the Logos service is what the USB Dongles are conflicting with.
Ben Sisney
FlexRIO V&V Engineer
National Instruments

Mobile Module for Labview 2009

Similar Messages

Maybe you are looking for