Mobility Anchor connection drops during authentication

Hi,
I have a strange situation, hopefully someone can help. I have a WLAN setup with foreign - anchor controllers and MAC address authentication using central RADIUS server. In some cases for some clients the foreign export cannot build up because during the 802.11 process the foreign disconnects the client due to a session timer expires. Some clients can connect, others experience this issue. Sometimes client can get IP address via the anchor DHCP proxy but then foreign disconnects it with expiring message. (foreign sw version 6.0.202, anchor sw version 6.0.188 but we have same situation with other foreign which has 7.4.110 version)
Debug shows the following (suspicious part is in red):
*Jan 15 12:07:01.190: 60:c5:47:99:b0:a6 Reassociation received from mobile on AP e8:04:62:f6:bf:00
*Jan 15 12:07:01.190: 60:c5:47:99:b0:a6 Applying site-specific IPv6 override for station 60:c5:47:99:b0:a6 - vapId 3, site 'default-group', interface 'management'
*Jan 15 12:07:01.190: 60:c5:47:99:b0:a6 Applying IPv6 Interface Policy for station 60:c5:47:99:b0:a6 - vlan 850, interface id 0, interface 'management'
*Jan 15 12:07:01.190: 60:c5:47:99:b0:a6 STA - rates (6): 24 164 48 72 96 108 0 0 0 0 0 0 0 0 0 0
*Jan 15 12:07:01.190: 60:c5:47:99:b0:a6 0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [e8:04:62:f6:cd:d0]
*Jan 15 12:07:01.190: 60:c5:47:99:b0:a6 Updated location for station old AP e8:04:62:f6:cd:d0-0, new AP e8:04:62:f6:bf:00-0
*Jan 15 12:07:01.190: 60:c5:47:99:b0:a6 apfProcessAssocReq (apf_80211.c:4270) Changing state for mobile 60:c5:47:99:b0:a6 on AP e8:04:62:f6:bf:00 from Probe to AAA Pending
*Jan 15 12:07:01.190: 60:c5:47:99:b0:a6 Scheduling deletion of Mobile Station:  (callerId: 20) in 10 seconds
*Jan 15 12:07:01.326: 60:c5:47:99:b0:a6 Inserting AAA Override struct for mobile MAC: 60:c5:47:99:b0:a6, source 2
*Jan 15 12:07:01.326: 60:c5:47:99:b0:a6 Setting session timeout 7201 on mobile 60:c5:47:99:b0:a6
*Jan 15 12:07:01.326: 60:c5:47:99:b0:a6 Session Timeout is 7201 - starting session timer for the mobile
*Jan 15 12:07:01.326: 60:c5:47:99:b0:a6 0.0.0.0 START (0) Initializing policy
*Jan 15 12:07:01.327: 60:c5:47:99:b0:a6 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
*Jan 15 12:07:01.327: 60:c5:47:99:b0:a6 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
*Jan 15 12:07:01.327: 60:c5:47:99:b0:a6 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP e8:04:62:f6:bf:00 vapId 3 apVapId 3
*Jan 15 12:07:01.327: 60:c5:47:99:b0:a6 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
*Jan 15 12:07:01.327: 60:c5:47:99:b0:a6 apfPemAddUser2 (apf_policy.c:213) Changing state for mobile 60:c5:47:99:b0:a6 on AP e8:04:62:f6:bf:00 from AAA Pending to Associated
*Jan 15 12:07:01.327: 60:c5:47:99:b0:a6 Scheduling deletion of Mobile Station:  (callerId: 49) in 7200 seconds
*Jan 15 12:07:01.327: 60:c5:47:99:b0:a6 Sending Assoc Response to station on BSSID e8:04:62:f6:bf:00 (status 0) Vap Id 3 Slot 0
*Jan 15 12:07:01.327: 60:c5:47:99:b0:a6 apfProcessRadiusAssocResp (apf_80211.c:1956) Changing state for mobile 60:c5:47:99:b0:a6 on AP e8:04:62:f6:bf:00 from Associated to Associated
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6 Applying post-handoff policy for station 60:c5:47:99:b0:a6 - valid mask 0xb00
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6     QOS Level: -1, DSCP: -1, dot1p: -1, Data Avg: -1, realtime Avg: -1, Data Burst -1, Realtime Burst -1
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6     Session: 7200, User session: 7201, User elapsed 104  Interface: (null) ACL: N/A
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6 Inserting AAA Override struct for mobile MAC: 60:c5:47:99:b0:a6, source 16
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6 Setting session timeout 7201 on mobile 60:c5:47:99:b0:a6
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6 Session Timeout is 7201 - starting session timer for the mobile
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6 Scheduling deletion of Mobile Station:  (callerId: 55) in 7200 seconds
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
*Jan 15 12:07:01.328: 60:c5:47:99:b0:a6 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
*Jan 15 12:07:01.329: 60:c5:47:99:b0:a6 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 4245
*Jan 15 12:07:01.329: 60:c5:47:99:b0:a6 0.0.0.0 RUN (20) Adding Fast Path rule  type = Airespace AP Client on AP e8:04:62:f6:bf:00, slot 0, interface = 29, QOS = 0  ACL Id = 255, Jumbo Frames = NO, 802.1
*Jan 15 12:07:01.329: 60:c5:47:99:b0:a6 0.0.0.0 RUN (20) Successfully plumbed mobile rule (ACL ID 255)
*Jan 15 12:07:01.332: 60:c5:47:99:b0:a6 Set bi-dir guest tunnel for 60:c5:47:99:b0:a6 as in Export Foreign role
*Jan 15 12:07:01.335: 60:c5:47:99:b0:a6 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
*Jan 15 12:07:11.890: 60:c5:47:99:b0:a6 0.0.0.0 RUN (20) State Update from Mobility-Complete to Mobility-Incomplete
*Jan 15 12:07:11.890: 60:c5:47:99:b0:a6 apfMmProcessDeleteMobile (apf_mm.c:531) Expiring Mobile!
*Jan 15 12:07:11.890: 60:c5:47:99:b0:a6 apfMsExpireMobileStation (apf_ms.c:4427) Changing state for mobile 60:c5:47:99:b0:a6 on AP e8:04:62:f6:bf:00 from Associated to Disassociated
*Jan 15 12:07:11.891: 60:c5:47:99:b0:a6 apfMsExpireMobileStation (apf_ms.c:4548) Changing state for mobile 60:c5:47:99:b0:a6 on AP e8:04:62:f6:bf:00 from Disassociated to Idle
*Jan 15 12:07:11.891: 60:c5:47:99:b0:a6 0.0.0.0 RUN (20) Deleted mobile LWAPP rule on AP [e8:04:62:f6:bf:00]
*Jan 15 12:07:11.891: 60:c5:47:99:b0:a6 Deleting mobile on AP e8:04:62:f6:bf:00(0)
*Jan 15 12:07:11.894: 60:c5:47:99:b0:a6 0.0.0.0 Removed NPU entry.
*Jan 15 12:07:12.053: 60:c5:47:99:b0:a6 Adding mobile on LWAPP AP 68:bd:ab:48:80:f0(0)
*Jan 15 12:07:12.053: 60:c5:47:99:b0:a6 Scheduling deletion of Mobile Station:  (callerId: 23) in 5 seconds
*Jan 15 12:07:12.053: 60:c5:47:99:b0:a6 apfProcessProbeReq (apf_80211.c:4761) Changing state for mobile 60:c5:47:99:b0:a6 on AP 68:bd:ab:48:80:f0 from Idle to Probe
Question: Why is that 10 sec timer still ticking at that phase when client already reached RUN state?
On a foreign wlc with sw 7.4.110 using anchor with sw 6.0.188 the situation is even worse, all clients have this issue and cannot connect.
Thanks
Hege

Hi,
Yes, that was the first thing to check. We don't use the DHCP required option (unchecked on both sides). The only difference between acnhor and foreign configuration is that in foreign L2 macfiltering is enabled and radius servers are specified while on anchor it is not enabled and specified. I have tried it on anchor with enabling macfiltering (without radius servers specified there) but I have the same behaviour. AAA override is also enabled on both sides.
I have also increased the authentication timeout in advanced timers options from 10 sec to 40 secs but no luck, debug shows the same 10secs.
I am thinking on 2 options. 1st option is that the anchor software is too old (6.0.188) and needs to be upgraded to 7.0.240 (anchor is a 4400 wlc). 2nd option is that there might be too much delay between anchor and foreign?
On the same setup if we use guest access with web authentication on the anchor side (no MAC authentication), then eveyrthing is fine.
Thanks
Hege

Similar Messages

  • Data Connection drops during a Phone call on iPhone 5

    Does anyone have a weird issue of data dropping completely during the call? When I place a call the 3g icon disappears completely and nothing that requires data works until I hung up. Once I hang up the 3g service is restored pretty much instantly.

    What carrier are you using?
    Some carriers don't support Internt Data while on calls. 
    Talk to your cell service provider for details about your service. 

  • Connections drop when using Cisco Anyconnect Secure Mobility Client

    Folks I have a strange issues. I have a few laptops that I'm testing using the Cisco AnyConnect Secure Mobility Client Network Access Manager. We like the interface and overall are happy, but have one nagging issue. Periodically the connection drops when using the client, and the only way to reconnect is to choose the Network repair option on the client. That fixes it just fine, but we shouldn't have to do this. The same clients using the built in WIndows supplicant do not have this problem. We are on version 3.0.07059.

    Right now I'm testing on a single access point (autonomous) with WEP! The same laptop works fine without the Cisco client. Usually it is several hours, 12 or more when it happens, but I've seen it less than that. And I've seen it up for over a day and a half. At this point I just don't trust the client to roll out to a larger audience.

  • Connection drops dead during session (OS 10.5.6 problem?)

    I am chatting without trouble for quite a long time now, till now. During sessions the connection drops dead after a minute or 3. Buddy freezes in the chatwindow and his/her little cam in the chatlist gets gray. Problem repeats itself with several buddy's. Typing a message to the buddy results in an AOL server time-out message. Restarting I-Chat brings the buddy to life again, connection is made swiftly and after a miute or 2-3 the line drops dead again. The only thing recently changed on my system is the software update to 10.5.6. Could it be a bug in this update? Any other experiences regarding 10.5.6 and I-Chat?
    Kind regards, Julius

    Only if you have Perian (1.1.3)
    Downdgrading Perian only fixes Perian.
    Defcom says Use Quicktime at 1.5Mbps. I would concur.
    He also says try the port at 443. (I would go as far as saying try it with and Without th SSL Login as well
    I would also consider deleting com.apple.ichat.AIM.plist and restarting iChat.
    I would also consider Rebooting the Modem to clear any odd ports being held onto.
    8:16 PM Wednesday; January 21, 2009
    Message was edited by: Ralph Johns (UK)

  • Internet Connection drops when incoming telephone ...

    On 14th December 2011 during a period of very high winds and heavy rain an incoming telephone call caused the internet connection to drop and it eventually restored itself after about 2 hours. When I answer a call the internet connection drops after about 30 seconds and then reconnects after about a further 40 seconds. All incoming local calls cause the internet connection to drop. As far as I can tell incoming calls from other exchanges seem to be OK. Incoming calls from mobile phones sometimes cause the internet connection to drop. The line is unaffected by outgoing telephone calls. I have a BT HomeHub 2B plugged into an upstairs telephone socket and connected by ethernet to my PC. I have another telephone socket downstairs, each socket is fitted with a filter. I have have tried every combination of my two standard telephones and 4 filters in each socket and every local call causes the internet connection to drop and reconnect. I think it very unlikely that both phones and 4 filters have become faulty at the exactly the same time. I have connected the Home Hub and telephone with a filter to the test socket and asked a friend on the local exchange to call me and the internet connection dropped and reconnected as before. Since moving to this house 2 years ago I have had four previous interruptions to the broadband service all of which were caused by problems probably at the exchange. The last one took 8 days to correct after countless calls to the "Help Line". Their fall back position is always to assume that there is no problem with the BT line. So I am not even going to try to explain this over the telephone. This is the information on the BT Home Hub Event Log, it is typical for every occurrence of the problem. Dec 26 11:42:42 2011 ERR 2011-12-26T11:42:42Z cwmp: mt_cwmp: session error: Could not resolve host Dec 26 11:43:19 2011 (1035438.010000) RTNL: Received ERROR reply 'No such process' for message type 0x19 Is this a problem with the Homehub, the line, or at the exchange?

    not sure I read your post correctly but are you saying if someone from another exchange phones then the broadband is ok and it only drops if someone from your own exchange phones?
    if the possible sollution from chris6273 does not work, and you have already tried the test socket then I would contact the mods for assistance  http://bt.custhelp.com/app/contact_email/c/4951
    the mods can take up to 3 days to reply
    If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
    If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

  • Wifi connection drops down. [SOLVED]

    Hi, I'm having some issues with the wifi, in my notebook lenovo b5070. The main problem is that the connection drops down after 20, 30 minutes. I tried to change from NetworkManager to Wicd, but that didn't change anything. I also tried to create a profile and connect me through netctl, but again that didn't change anything. Other issues that I'm having are: Sometimes I can't even connect to the wifi, or if I can connect finally, and I try to request some website, the browser keeps idle and finally shows a "Server not found" message. Also the wifi signal seems pretty fine. I also tried change the tx, rts to the max with iwconfig, but this didn't change anything. I'm running out of ideas. Any idea?
    Here is some info:
    [astinx@compu ~]$ lsusb
    Bus 003 Device 002: ID 8087:8000 Intel Corp.
    Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
    Bus 001 Device 005: ID 138a:0011 Validity Sensors, Inc. VFS5011 Fingerprint Reader
    Bus 001 Device 004: ID 0bda:b728 Realtek Semiconductor Corp.
    Bus 001 Device 003: ID 0c45:6514 Microdia
    Bus 001 Device 002: ID 0458:012b KYE Systems Corp. (Mouse Systems)
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    [astinx@compu ~]$ iwconfig
    wlp9s0 IEEE 802.11bgn ESSID:"albele"
    Mode:Managed Frequency:2.437 GHz Access Point: 00:1D:7E:6A:C4:67
    Bit Rate=54 Mb/s Tx-Power=20 dBm
    Retry short limit:7 RTS thr=2347 B Fragment thr:off
    Power Management:off
    Link Quality=52/70 Signal level=-58 dBm
    Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
    Tx excessive retries:0 Invalid misc:0 Missed beacon:0
    lo no wireless extensions.
    enp8s0 no wireless extensions.
    [astinx@compu ~]$ ifconfig
    enp8s0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
    ether f0:76:1c:0c:12:99 txqueuelen 1000 (Ethernet)
    RX packets 0 bytes 0 (0.0 B)
    RX errors 0 dropped 0 overruns 0 frame 0
    TX packets 0 bytes 0 (0.0 B)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
    lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
    inet 127.0.0.1 netmask 255.0.0.0
    inet6 ::1 prefixlen 128 scopeid 0x10<host>
    loop txqueuelen 0 (Local Loopback)
    RX packets 336 bytes 29472 (28.7 KiB)
    RX errors 0 dropped 0 overruns 0 frame 0
    TX packets 336 bytes 29472 (28.7 KiB)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
    wlp9s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
    inet 192.168.1.111 netmask 255.255.255.0 broadcast 192.168.1.255
    inet6 fe80::fa77:2850:54a4:4213 prefixlen 64 scopeid 0x20<link>
    ether 38:b1:db:4f:f7:33 txqueuelen 1000 (Ethernet)
    RX packets 192 bytes 52270 (51.0 KiB)
    RX errors 0 dropped 0 overruns 0 frame 0
    TX packets 1297 bytes 138803 (135.5 KiB)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
    [astinx@compu ~]$ lspci -k
    00:00.0 Host bridge: Intel Corporation Haswell-ULT DRAM Controller (rev 0b)
    Subsystem: Lenovo Device 3978
    00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 0b)
    Subsystem: Lenovo Device 3978
    Kernel driver in use: i915
    Kernel modules: i915
    00:03.0 Audio device: Intel Corporation Haswell-ULT HD Audio Controller (rev 0b)
    Subsystem: Lenovo Device 3978
    Kernel driver in use: snd_hda_intel
    Kernel modules: snd_hda_intel
    00:14.0 USB controller: Intel Corporation 8 Series USB xHCI HC (rev 04)
    Subsystem: Lenovo Device 3978
    Kernel driver in use: xhci_hcd
    Kernel modules: xhci_pci
    00:16.0 Communication controller: Intel Corporation 8 Series HECI #0 (rev 04)
    Subsystem: Lenovo Device 3978
    Kernel driver in use: mei_me
    Kernel modules: mei_me
    00:1b.0 Audio device: Intel Corporation 8 Series HD Audio Controller (rev 04)
    Subsystem: Lenovo Device 3978
    Kernel driver in use: snd_hda_intel
    Kernel modules: snd_hda_intel
    00:1c.0 PCI bridge: Intel Corporation 8 Series PCI Express Root Port 1 (rev e4)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
    00:1c.1 PCI bridge: Intel Corporation 8 Series PCI Express Root Port 2 (rev e4)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
    00:1c.2 PCI bridge: Intel Corporation 8 Series PCI Express Root Port 3 (rev e4)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
    00:1c.3 PCI bridge: Intel Corporation 8 Series PCI Express Root Port 4 (rev e4)
    Kernel driver in use: pcieport
    Kernel modules: shpchp
    00:1d.0 USB controller: Intel Corporation 8 Series USB EHCI #1 (rev 04)
    Subsystem: Lenovo Device 3978
    Kernel driver in use: ehci-pci
    Kernel modules: ehci_pci
    00:1f.0 ISA bridge: Intel Corporation 8 Series LPC Controller (rev 04)
    Subsystem: Lenovo Device 3978
    Kernel driver in use: lpc_ich
    Kernel modules: lpc_ich
    00:1f.2 SATA controller: Intel Corporation 8 Series SATA Controller 1 [AHCI mode] (rev 04)
    Subsystem: Lenovo Device 3978
    Kernel driver in use: ahci
    Kernel modules: ahci
    00:1f.3 SMBus: Intel Corporation 8 Series SMBus Controller (rev 04)
    Subsystem: Lenovo Device 3978
    Kernel modules: i2c_i801
    02:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)
    Subsystem: Lenovo Device 3801
    Kernel driver in use: rtsx_pci
    Kernel modules: rtsx_pci
    08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 10)
    Subsystem: Lenovo Device 380e
    Kernel driver in use: r8169
    Kernel modules: r8169
    09:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8723BE PCIe Wireless Network Adapter
    Subsystem: Lenovo Device b736
    Kernel driver in use: rtl8723be
    Kernel modules: rtl8723be
    [astinx@compu ~]$ lsusb
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.18.5-1-ARCH (builduser@tobias) (gcc version 4.9.2 20141224 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Jan 30 07:31:50 CET 2015
    [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=37f0494b-6280-4a2a-92af-9abc262b3476 rw resume=UUID=38f5c3ea-1283-4a7e-a952-49dee4e9b5ae quiet
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000006efff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000006f000-0x000000000006ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000070000-0x0000000000087fff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000000088000-0x00000000000bffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000009735ffff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000097360000-0x0000000097b5ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000097b60000-0x000000009c36efff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009c36f000-0x000000009c56efff] type 20
    [ 0.000000] BIOS-e820: [mem 0x000000009c56f000-0x000000009cebefff] reserved
    [ 0.000000] BIOS-e820: [mem 0x000000009cebf000-0x000000009cfbefff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x000000009cfbf000-0x000000009cffefff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x000000009cfff000-0x000000009cffffff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009d000000-0x000000009f9fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fe101000-0x00000000fe112fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb0ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ffa00000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000015f5fffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] efi: EFI v2.31 by INSYDE Corp.
    [ 0.000000] efi: ACPI=0x9cffe000 ACPI 2.0=0x9cffe014 SMBIOS=0x9cebef98
    [ 0.000000] efi: mem00: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000000000000-0x0000000000001000) (0MB)
    [ 0.000000] efi: mem01: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000001000-0x000000000006f000) (0MB)
    [ 0.000000] efi: mem02: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000000006f000-0x0000000000070000) (0MB)
    [ 0.000000] efi: mem03: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000070000-0x0000000000080000) (0MB)
    [ 0.000000] efi: mem04: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000000080000-0x0000000000082000) (0MB)
    [ 0.000000] efi: mem05: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000082000-0x0000000000088000) (0MB)
    [ 0.000000] efi: mem06: [Runtime Data |RUN| | | | |WB|WT|WC|UC] range=[0x0000000000088000-0x000000000009f000) (0MB)
    [ 0.000000] efi: mem07: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000000009f000-0x00000000000a0000) (0MB)
    [ 0.000000] efi: mem08: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x0000000000100000-0x0000000000f3b000) (14MB)
    [ 0.000000] efi: mem09: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000f3b000-0x0000000037926000) (873MB)
    [ 0.000000] efi: mem10: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x0000000037926000-0x0000000037c8b000) (3MB)
    [ 0.000000] efi: mem11: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000037c8b000-0x000000006ea96000) (878MB)
    [ 0.000000] efi: mem12: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x000000006ea96000-0x0000000094b70000) (608MB)
    [ 0.000000] efi: mem13: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000094b70000-0x0000000094b90000) (0MB)
    [ 0.000000] efi: mem14: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000094b90000-0x00000000968e3000) (29MB)
    [ 0.000000] efi: mem15: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000968e3000-0x0000000097360000) (10MB)
    [ 0.000000] efi: mem16: [Reserved | | | | | |WB|WT|WC|UC] range=[0x0000000097360000-0x0000000097b60000) (8MB)
    [ 0.000000] efi: mem17: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000097b60000-0x0000000097d52000) (1MB)
    [ 0.000000] efi: mem18: [Loader Code | | | | | |WB|WT|WC|UC] range=[0x0000000097d52000-0x0000000097d6f000) (0MB)
    [ 0.000000] efi: mem19: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000097d6f000-0x000000009951f000) (23MB)
    [ 0.000000] efi: mem20: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009951f000-0x0000000099f09000) (9MB)
    [ 0.000000] efi: mem21: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000099f09000-0x0000000099f0e000) (0MB)
    [ 0.000000] efi: mem22: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000099f0e000-0x0000000099f14000) (0MB)
    [ 0.000000] efi: mem23: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000099f14000-0x0000000099f16000) (0MB)
    [ 0.000000] efi: mem24: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000099f16000-0x0000000099f3f000) (0MB)
    [ 0.000000] efi: mem25: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000099f3f000-0x0000000099f40000) (0MB)
    [ 0.000000] efi: mem26: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x0000000099f40000-0x000000009a08e000) (1MB)
    [ 0.000000] efi: mem27: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009a08e000-0x000000009a094000) (0MB)
    [ 0.000000] efi: mem28: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009a094000-0x000000009a095000) (0MB)
    [ 0.000000] efi: mem29: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009a095000-0x000000009a097000) (0MB)
    [ 0.000000] efi: mem30: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009a097000-0x000000009a09b000) (0MB)
    [ 0.000000] efi: mem31: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009a09b000-0x000000009a09c000) (0MB)
    [ 0.000000] efi: mem32: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009a09c000-0x000000009a0d5000) (0MB)
    [ 0.000000] efi: mem33: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009a0d5000-0x000000009a0d7000) (0MB)
    [ 0.000000] efi: mem34: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009a0d7000-0x000000009a0dc000) (0MB)
    [ 0.000000] efi: mem35: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009a0dc000-0x000000009a0df000) (0MB)
    [ 0.000000] efi: mem36: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009a0df000-0x000000009a0e7000) (0MB)
    [ 0.000000] efi: mem37: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009a0e7000-0x000000009a0ea000) (0MB)
    [ 0.000000] efi: mem38: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009a0ea000-0x000000009a0eb000) (0MB)
    [ 0.000000] efi: mem39: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009a0eb000-0x000000009a0ef000) (0MB)
    [ 0.000000] efi: mem40: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009a0ef000-0x000000009a193000) (0MB)
    [ 0.000000] efi: mem41: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009a193000-0x000000009a194000) (0MB)
    [ 0.000000] efi: mem42: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009a194000-0x000000009bd6f000) (27MB)
    [ 0.000000] efi: mem43: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000009bd6f000-0x000000009bf51000) (1MB)
    [ 0.000000] efi: mem44: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x000000009bf51000-0x000000009bf5b000) (0MB)
    [ 0.000000] efi: mem45: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x000000009bf5b000-0x000000009c36f000) (4MB)
    [ 0.000000] efi: mem46: [Runtime Code |RUN| | | | |WB|WT|WC|UC] range=[0x000000009c36f000-0x000000009c56f000) (2MB)
    [ 0.000000] efi: mem47: [Runtime Data |RUN| | | | |WB|WT|WC|UC] range=[0x000000009c56f000-0x000000009cabf000) (5MB)
    [ 0.000000] efi: mem48: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000009cabf000-0x000000009cebf000) (4MB)
    [ 0.000000] efi: mem49: [ACPI Memory NVS | | | | | |WB|WT|WC|UC] range=[0x000000009cebf000-0x000000009cfbf000) (1MB)
    [ 0.000000] efi: mem50: [ACPI Reclaim Memory| | | | | |WB|WT|WC|UC] range=[0x000000009cfbf000-0x000000009cfff000) (0MB)
    [ 0.000000] efi: mem51: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x000000009cfff000-0x000000009d000000) (0MB)
    [ 0.000000] efi: mem52: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000100000000-0x000000015f600000) (1526MB)
    [ 0.000000] efi: mem53: [Reserved | | | | | | | | | ] range=[0x00000000000a0000-0x00000000000c0000) (0MB)
    [ 0.000000] efi: mem54: [Reserved | | | | | | | | | ] range=[0x000000009d000000-0x000000009fa00000) (42MB)
    [ 0.000000] efi: mem55: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000e0000000-0x00000000f0000000) (256MB)
    [ 0.000000] efi: mem56: [Reserved | | | | | | | | | ] range=[0x00000000fe101000-0x00000000fe113000) (0MB)
    [ 0.000000] efi: mem57: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000feb00000-0x00000000feb10000) (0MB)
    [ 0.000000] efi: mem58: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fec00000-0x00000000fec01000) (0MB)
    [ 0.000000] efi: mem59: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fed00000-0x00000000fed1c000) (0MB)
    [ 0.000000] efi: mem60: [Memory Mapped I/O |RUN| | | | | | | | ] range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
    [ 0.000000] efi: mem61: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fed20000-0x00000000fee01000) (0MB)
    [ 0.000000] efi: mem62: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000ffa00000-0x0000000100000000) (6MB)
    [ 0.000000] SMBIOS 2.7 present.
    [ 0.000000] DMI: LENOVO 20384/Lenovo B50-70, BIOS 9DCN21WW(V2.02) 06/27/2014
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x15f600 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-E7FFF write-protect
    [ 0.000000] E8000-EFFFF write-combining
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0000000000 mask 7E00000000 write-back
    [ 0.000000] 1 base 009D000000 mask 7FFF000000 uncachable
    [ 0.000000] 2 base 009E000000 mask 7FFE000000 uncachable
    [ 0.000000] 3 base 00A0000000 mask 7FE0000000 uncachable
    [ 0.000000] 4 base 00C0000000 mask 7FC0000000 uncachable
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] 8 disabled
    [ 0.000000] 9 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: update [mem 0x9d000000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0x9d000 max_arch_pfn = 0x400000000
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000082000] 82000 size 24576
    [ 0.000000] Using GB pages for direct mapping
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b36000, 0x01b36fff] PGTABLE
    [ 0.000000] BRK [0x01b37000, 0x01b37fff] PGTABLE
    [ 0.000000] BRK [0x01b38000, 0x01b38fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x15f400000-0x15f5fffff]
    [ 0.000000] [mem 0x15f400000-0x15f5fffff] page 2M
    [ 0.000000] BRK [0x01b39000, 0x01b39fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x15c000000-0x15f3fffff]
    [ 0.000000] [mem 0x15c000000-0x15f3fffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x15bffffff]
    [ 0.000000] [mem 0x100000000-0x13fffffff] page 1G
    [ 0.000000] [mem 0x140000000-0x15bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x9735ffff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
    [ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
    [ 0.000000] [mem 0x80000000-0x971fffff] page 2M
    [ 0.000000] [mem 0x97200000-0x9735ffff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x97b60000-0x9c36efff]
    [ 0.000000] [mem 0x97b60000-0x97bfffff] page 4k
    [ 0.000000] [mem 0x97c00000-0x9c1fffff] page 2M
    [ 0.000000] [mem 0x9c200000-0x9c36efff] page 4k
    [ 0.000000] BRK [0x01b3a000, 0x01b3afff] PGTABLE
    [ 0.000000] BRK [0x01b3b000, 0x01b3bfff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x9cfff000-0x9cffffff]
    [ 0.000000] [mem 0x9cfff000-0x9cffffff] page 4k
    [ 0.000000] RAMDISK: [mem 0x37926000-0x37c8afff]
    [ 0.000000] ACPI: Early table checksum verification disabled
    [ 0.000000] ACPI: RSDP 0x000000009CFFE014 000024 (v02 LENOVO)
    [ 0.000000] ACPI: XSDT 0x000000009CFFE210 0000B4 (v01 LENOVO CB-01 00000001 01000013)
    [ 0.000000] ACPI: FACP 0x000000009CFF8000 00010C (v05 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: DSDT 0x000000009CFE7000 00DA18 (v02 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: FACS 0x000000009CFBA000 000040
    [ 0.000000] ACPI: UEFI 0x000000009CFFD000 000236 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: FPDT 0x000000009CFFB000 000044 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: MSDM 0x000000009CFFA000 000055 (v03 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: ASF! 0x000000009CFF9000 0000A5 (v32 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: HPET 0x000000009CFF7000 000038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: APIC 0x000000009CFF6000 00008C (v03 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: MCFG 0x000000009CFF5000 00003C (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: WDAT 0x000000009CFE6000 000224 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFE5000 000700 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: BOOT 0x000000009CFE3000 000028 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: LPIT 0x000000009CFE2000 000094 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: ASPT 0x000000009CFE0000 000034 (v07 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: DBGP 0x000000009CFDF000 000034 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFDA000 000539 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFD9000 000AD8 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x000000009CFD5000 003537 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: BGRT 0x000000009CFD4000 000038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000015f5fffff]
    [ 0.000000] NODE_DATA(0) allocated [mem 0x15f5f9000-0x15f5fcfff]
    [ 0.000000] [ffffea0000000000-ffffea00057fffff] PMD -> [ffff88015ac00000-ffff88015ebfffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x15f5fffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0006efff]
    [ 0.000000] node 0: [mem 0x00070000-0x00087fff]
    [ 0.000000] node 0: [mem 0x00100000-0x9735ffff]
    [ 0.000000] node 0: [mem 0x97b60000-0x9c36efff]
    [ 0.000000] node 0: [mem 0x9cfff000-0x9cffffff]
    [ 0.000000] node 0: [mem 0x100000000-0x15f5fffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00001000-0x15f5fffff]
    [ 0.000000] On node 0 totalpages: 1028342
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 24 pages reserved
    [ 0.000000] DMA zone: 3974 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 9902 pages used for memmap
    [ 0.000000] DMA32 zone: 633712 pages, LIFO batch:31
    [ 0.000000] Normal zone: 6104 pages used for memmap
    [ 0.000000] Normal zone: 390656 pages, LIFO batch:31
    [ 0.000000] Reserving Intel graphics stolen memory at 0x9da00000-0x9f9fffff
    [ 0.000000] ACPI: PM-Timer IO Port: 0x1808
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
    [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x0006f000-0x0006ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x00088000-0x000bffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000c0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x97360000-0x97b5ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9c36f000-0x9c56efff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9c56f000-0x9cebefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9cebf000-0x9cfbefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9cfbf000-0x9cffefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9d000000-0x9f9fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x9fa00000-0xdfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfe100fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfe101000-0xfe112fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfe113000-0xfeafffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb0ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfeb10000-0xfebfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfee00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xff9fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xffa00000-0xffffffff]
    [ 0.000000] e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff88015f200000 s82880 r8192 d31808 u262144
    [ 0.000000] pcpu-alloc: s82880 r8192 d31808 u262144 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1012248
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=37f0494b-6280-4a2a-92af-9abc262b3476 rw resume=UUID=38f5c3ea-1283-4a7e-a952-49dee4e9b5ae quiet
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
    [ 0.000000] AGP: Checking aperture...
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 3909256K/4113368K available (5480K kernel code, 908K rwdata, 1720K rodata, 1160K init, 1184K bss, 204112K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
    [ 0.000000] NR_IRQS:8448 nr_irqs:760 0
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 16777216 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 2394.377 MHz processor
    [ 0.000041] Calibrating delay loop (skipped), value calculated using timer frequency.. 4790.28 BogoMIPS (lpj=7981256)
    [ 0.000045] pid_max: default: 32768 minimum: 301
    [ 0.000053] ACPI: Core revision 20140926
    [ 0.018809] ACPI: All ACPI Tables successfully acquired
    [ 0.039185] Security Framework initialized
    [ 0.039194] Yama: becoming mindful.
    [ 0.039553] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.040627] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.041121] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.041129] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.041378] Initializing cgroup subsys memory
    [ 0.041384] Initializing cgroup subsys devices
    [ 0.041386] Initializing cgroup subsys freezer
    [ 0.041389] Initializing cgroup subsys net_cls
    [ 0.041391] Initializing cgroup subsys blkio
    [ 0.041417] CPU: Physical Processor ID: 0
    [ 0.041419] CPU: Processor Core ID: 0
    [ 0.041424] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.042651] mce: CPU supports 7 MCE banks
    [ 0.042667] CPU0: Thermal monitoring enabled (TM1)
    [ 0.042682] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
    Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
    [ 0.042812] Freeing SMP alternatives memory: 20K (ffffffff81a07000 - ffffffff81a0c000)
    [ 0.043856] Ignoring BGRT: invalid status 0 (expected 1)
    [ 0.045955] ftrace: allocating 20931 entries in 82 pages
    [ 0.058119] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.091151] smpboot: CPU0: Intel(R) Core(TM) i5-4210U CPU @ 1.70GHz (fam: 06, model: 45, stepping: 01)
    [ 0.091159] TSC deadline timer enabled
    [ 0.091185] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
    [ 0.091212] ... version: 3
    [ 0.091214] ... bit width: 48
    [ 0.091215] ... generic registers: 4
    [ 0.091216] ... value mask: 0000ffffffffffff
    [ 0.091217] ... max period: 0000ffffffffffff
    [ 0.091218] ... fixed-purpose events: 3
    [ 0.091220] ... event mask: 000000070000000f
    [ 0.111308] x86: Booting SMP configuration:
    [ 0.111311] .... node #0, CPUs: #1
    [ 0.125959] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.132620] #2 #3
    [ 0.168461] x86: Booted up 1 node, 4 CPUs
    [ 0.168465] smpboot: Total of 4 processors activated (19162.14 BogoMIPS)
    [ 0.173479] devtmpfs: initialized
    [ 0.176167] PM: Registering ACPI NVS region [mem 0x9cebf000-0x9cfbefff] (1048576 bytes)
    [ 0.177292] pinctrl core: initialized pinctrl subsystem
    [ 0.177339] RTC time: 15:39:50, date: 02/08/15
    [ 0.177475] NET: Registered protocol family 16
    [ 0.189973] cpuidle: using governor ladder
    [ 0.203321] cpuidle: using governor menu
    [ 0.203363] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
    [ 0.203364] ACPI: bus type PCI registered
    [ 0.203366] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.203456] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.203459] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
    [ 0.203881] PCI: Using configuration type 1 for base access
    [ 0.217092] ACPI: Added _OSI(Module Device)
    [ 0.217094] ACPI: Added _OSI(Processor Device)
    [ 0.217096] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.217098] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.222927] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.237854] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.250192] ACPI: Dynamic OEM Table Load:
    [ 0.250204] ACPI: SSDT 0xFFFF880158F80C00 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20121220)
    [ 0.263714] ACPI: Dynamic OEM Table Load:
    [ 0.263726] ACPI: SSDT 0xFFFF880158F59800 0005AA (v01 PmRef ApIst 00003000 INTL 20121220)
    [ 0.276877] ACPI: Dynamic OEM Table Load:
    [ 0.276887] ACPI: SSDT 0xFFFF880158E92800 000119 (v01 PmRef ApCst 00003000 INTL 20121220)
    [ 0.303769] ACPI: Interpreter enabled
    [ 0.303781] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140926/hwxface-580)
    [ 0.303790] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140926/hwxface-580)
    [ 0.303817] ACPI: (supports S0 S3 S4 S5)
    [ 0.303818] ACPI: Using IOAPIC for interrupt routing
    [ 0.303851] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.416427] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
    [ 0.416435] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.417003] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
    [ 0.417721] PCI host bridge to bus 0000:00
    [ 0.417725] pci_bus 0000:00: root bus resource [bus 00-fe]
    [ 0.417728] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.417730] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.417732] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.417734] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
    [ 0.417736] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
    [ 0.417738] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
    [ 0.417740] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff]
    [ 0.417742] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
    [ 0.417744] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
    [ 0.417746] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
    [ 0.417748] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
    [ 0.417750] pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff]
    [ 0.417760] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
    [ 0.417946] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
    [ 0.417962] pci 0000:00:02.0: reg 0x10: [mem 0xb2000000-0xb23fffff 64bit]
    [ 0.417971] pci 0000:00:02.0: reg 0x18: [mem 0xa0000000-0xafffffff 64bit pref]
    [ 0.417977] pci 0000:00:02.0: reg 0x20: [io 0x6000-0x603f]
    [ 0.418153] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
    [ 0.418164] pci 0000:00:03.0: reg 0x10: [mem 0xb2610000-0xb2613fff 64bit]
    [ 0.418365] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
    [ 0.418385] pci 0000:00:14.0: reg 0x10: [mem 0xb2600000-0xb260ffff 64bit]
    [ 0.418450] pci 0000:00:14.0: PME# supported from D3hot D3cold
    [ 0.418565] pci 0000:00:14.0: System wakeup disabled by ACPI
    [ 0.418612] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
    [ 0.418635] pci 0000:00:16.0: reg 0x10: [mem 0xb2618000-0xb261801f 64bit]
    [ 0.418711] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
    [ 0.418877] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
    [ 0.418893] pci 0000:00:1b.0: reg 0x10: [mem 0xb2614000-0xb2617fff 64bit]
    [ 0.418968] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.419082] pci 0000:00:1b.0: System wakeup disabled by ACPI
    [ 0.419126] pci 0000:00:1c.0: [8086:9c10] type 01 class 0x060400
    [ 0.419198] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.419353] pci 0000:00:1c.1: [8086:9c12] type 01 class 0x060400
    [ 0.419428] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 0.419584] pci 0000:00:1c.2: [8086:9c14] type 01 class 0x060400
    [ 0.419659] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
    [ 0.419813] pci 0000:00:1c.3: [8086:9c16] type 01 class 0x060400
    [ 0.419888] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    [ 0.420052] pci 0000:00:1d.0: [8086:9c26] type 00 class 0x0c0320
    [ 0.420074] pci 0000:00:1d.0: reg 0x10: [mem 0xb261c000-0xb261c3ff]
    [ 0.420172] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
    [ 0.420309] pci 0000:00:1d.0: System wakeup disabled by ACPI
    [ 0.420363] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
    [ 0.420631] pci 0000:00:1f.2: [8086:9c03] type 00 class 0x010601
    [ 0.420647] pci 0000:00:1f.2: reg 0x10: [io 0x6088-0x608f]
    [ 0.420655] pci 0000:00:1f.2: reg 0x14: [io 0x6094-0x6097]
    [ 0.420663] pci 0000:00:1f.2: reg 0x18: [io 0x6080-0x6087]
    [ 0.420671] pci 0000:00:1f.2: reg 0x1c: [io 0x6090-0x6093]
    [ 0.420678] pci 0000:00:1f.2: reg 0x20: [io 0x6060-0x607f]
    [ 0.420686] pci 0000:00:1f.2: reg 0x24: [mem 0xb261b000-0xb261b7ff]
    [ 0.420728] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.420878] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
    [ 0.420894] pci 0000:00:1f.3: reg 0x10: [mem 0xb2619000-0xb26190ff 64bit]
    [ 0.420915] pci 0000:00:1f.3: reg 0x20: [io 0x6040-0x605f]
    [ 0.421136] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.421234] pci 0000:02:00.0: [10ec:5229] type 00 class 0xff0000
    [ 0.421269] pci 0000:02:00.0: reg 0x10: [mem 0xb1000000-0xb1000fff]
    [ 0.421424] pci 0000:02:00.0: supports D1 D2
    [ 0.421427] pci 0000:02:00.0: PME# supported from D1 D2 D3hot
    [ 0.421466] pci 0000:02:00.0: System wakeup disabled by ACPI
    [ 0.427022] pci 0000:00:1c.1: PCI bridge to [bus 02-07]
    [ 0.427027] pci 0000:00:1c.1: bridge window [io 0x5000-0x5fff]
    [ 0.427030] pci 0000:00:1c.1: bridge window [mem 0xb1000000-0xb1ffffff]
    [ 0.427036] pci 0000:00:1c.1: bridge window [mem 0xb0000000-0xb0ffffff 64bit pref]
    [ 0.427119] pci 0000:08:00.0: [10ec:8168] type 00 class 0x020000
    [ 0.427139] pci 0000:08:00.0: reg 0x10: [io 0x4000-0x40ff]
    [ 0.427169] pci 0000:08:00.0: reg 0x18: [mem 0xb2504000-0xb2504fff 64bit]
    [ 0.427188] pci 0000:08:00.0: reg 0x20: [mem 0xb2500000-0xb2503fff 64bit]
    [ 0.427291] pci 0000:08:00.0: supports D1 D2
    [ 0.427293] pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.427358] pci 0000:08:00.0: System wakeup disabled by ACPI
    [ 0.433685] pci 0000:00:1c.2: PCI bridge to [bus 08]
    [ 0.433689] pci 0000:00:1c.2: bridge window [io 0x4000-0x4fff]
    [ 0.433693] pci 0000:00:1c.2: bridge window [mem 0xb2500000-0xb25fffff]
    [ 0.433780] pci 0000:09:00.0: [10ec:b723] type 00 class 0x028000
    [ 0.433803] pci 0000:09:00.0: reg 0x10: [io 0x3000-0x30ff]
    [ 0.433837] pci 0000:09:00.0: reg 0x18: [mem 0xb2400000-0xb2403fff 64bit]
    [ 0.433959] pci 0000:09:00.0: supports D1 D2
    [ 0.433961] pci 0000:09:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.433994] pci 0000:09:00.0: System wakeup disabled by ACPI
    [ 0.443696] pci 0000:00:1c.3: PCI bridge to [bus 09]
    [ 0.443699] pci 0000:00:1c.3: bridge window [io 0x3000-0x3fff]
    [ 0.443703] pci 0000:00:1c.3: bridge window [mem 0xb2400000-0xb24fffff]
    [ 0.443740] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
    [ 0.497639] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.497696] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.497748] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.497800] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.497851] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.497902] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.497953] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.498004] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
    [ 0.498197] ACPI: Enabled 5 GPEs in block 00 to 7F
    [ 0.498242] ACPI : EC: GPE = 0x27, I/O: command/status = 0x66, data = 0x62
    [ 0.498365] vgaarb: setting as boot device: PCI:0000:00:02.0
    [ 0.498368] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.498372] vgaarb: loaded
    [ 0.498373] vgaarb: bridge control possible 0000:00:02.0
    [ 0.498519] PCI: Using ACPI for IRQ routing
    [ 0.504636] PCI: pci_cache_line_size set to 64 bytes
    [ 0.504686] e820: reserve RAM buffer [mem 0x0006f000-0x0006ffff]
    [ 0.504688] e820: reserve RAM buffer [mem 0x00088000-0x0008ffff]
    [ 0.504689] e820: reserve RAM buffer [mem 0x97360000-0x97ffffff]
    [ 0.504691] e820: reserve RAM buffer [mem 0x9c36f000-0x9fffffff]
    [ 0.504693] e820: reserve RAM buffer [mem 0x9d000000-0x9fffffff]
    [ 0.504695] e820: reserve RAM buffer [mem 0x15f600000-0x15fffffff]
    [ 0.504822] NetLabel: Initializing
    [ 0.504823] NetLabel: domain hash size = 128
    [ 0.504824] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.504838] NetLabel: unlabeled traffic allowed by default
    [ 0.504863] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
    [ 0.504870] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
    [ 0.506900] Switched to clocksource hpet
    [ 0.512939] pnp: PnP ACPI init
    [ 0.513126] system 00:00: [io 0x0680-0x069f] has been reserved
    [ 0.513129] system 00:00: [io 0x0500-0x053f] has been reserved
    [ 0.513132] system 00:00: [io 0xffff] has been reserved
    [ 0.513134] system 00:00: [io 0xffff] has been reserved
    [ 0.513136] system 00:00: [io 0xffff] has been reserved
    [ 0.513139] system 00:00: [io 0x1800-0x18fe] could not be reserved
    [ 0.513141] system 00:00: [io 0x164e-0x164f] has been reserved
    [ 0.513145] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.513202] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.513256] system 00:02: [io 0x1854-0x1857] has been reserved
    [ 0.513259] system 00:02: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
    [ 0.513288] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.513351] pnp 00:04: Plug and Play ACPI device, IDs SYN2b39 SYN0700 SYN0002 PNP0f13 (active)
    [ 0.563797] system 00:05: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.563800] system 00:05: [mem 0xfed10000-0xfed17fff] has been reserved
    [ 0.563802] system 00:05: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.563804] system 00:05: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.563807] system 00:05: [mem 0xe0000000-0xefffffff] has been reserved
    [ 0.563809] system 00:05: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.563811] system 00:05: [mem 0xfed90000-0xfed93fff] has been reserved
    [ 0.563813] system 00:05: [mem 0xff000000-0xff000fff] has been reserved
    [ 0.563816] system 00:05: [mem 0xff001000-0xff0010ff] has been reserved
    [ 0.563818] system 00:05: [mem 0xff010000-0xffffffff] could not be reserved
    [ 0.563821] system 00:05: [mem 0xfee00000-0xfeefffff] could not be reserved
    [ 0.563823] system 00:05: [mem 0x9fa20000-0x9fa20fff] has been reserved
    [ 0.563825] system 00:05: [mem 0x9fa10000-0x9fa1ffff] has been reserved
    [ 0.563829] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.564138] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.564571] pnp: PnP ACPI: found 7 devices
    [ 0.571172] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.571185] pci 0000:00:1c.1: PCI bridge to [bus 02-07]
    [ 0.571188] pci 0000:00:1c.1: bridge window [io 0x5000-0x5fff]
    [ 0.571193] pci 0000:00:1c.1: bridge window [mem 0xb1000000-0xb1ffffff]
    [ 0.571197] pci 0000:00:1c.1: bridge window [mem 0xb0000000-0xb0ffffff 64bit pref]
    [ 0.571203] pci 0000:00:1c.2: PCI bridge to [bus 08]
    [ 0.571206] pci 0000:00:1c.2: bridge window [io 0x4000-0x4fff]
    [ 0.571211] pci 0000:00:1c.2: bridge window [mem 0xb2500000-0xb25fffff]
    [ 0.571218] pci 0000:00:1c.3: PCI bridge to [bus 09]
    [ 0.571221] pci 0000:00:1c.3: bridge window [io 0x3000-0x3fff]
    [ 0.571226] pci 0000:00:1c.3: bridge window [mem 0xb2400000-0xb24fffff]
    [ 0.571235] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.571237] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.571239] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.571241] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
    [ 0.571243] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
    [ 0.571245] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
    [ 0.571247] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
    [ 0.571249] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
    [ 0.571251] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
    [ 0.571253] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
    [ 0.571255] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
    [ 0.571257] pci_bus 0000:00: resource 15 [mem 0x9fa00000-0xfeafffff]
    [ 0.571260] pci_bus 0000:02: resource 0 [io 0x5000-0x5fff]
    [ 0.571261] pci_bus 0000:02: resource 1 [mem 0xb1000000-0xb1ffffff]
    [ 0.571264] pci_bus 0000:02: resource 2 [mem 0xb0000000-0xb0ffffff 64bit pref]
    [ 0.571266] pci_bus 0000:08: resource 0 [io 0x4000-0x4fff]
    [ 0.571268] pci_bus 0000:08: resource 1 [mem 0xb2500000-0xb25fffff]
    [ 0.571270] pci_bus 0000:09: resource 0 [io 0x3000-0x3fff]
    [ 0.571272] pci_bus 0000:09: resource 1 [mem 0xb2400000-0xb24fffff]
    [ 0.571305] NET: Registered protocol family 2
    [ 0.571528] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
    [ 0.571618] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
    [ 0.571715] TCP: Hash tables configured (established 32768 bind 32768)
    [ 0.571736] TCP: reno registered
    [ 0.571744] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.571763] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.571824] NET: Registered protocol family 1
    [ 0.571842] pci 0000:00:02.0: Video device with shadowed ROM
    [ 0.583761] PCI: CLS 64 bytes, default 64
    [ 0.583812] Unpacking initramfs...
    [ 0.665763] Freeing initrd memory: 3476K (ffff880037926000 - ffff880037c8b000)
    [ 0.665775] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 0.665778] software IO TLB [mem 0x90b70000-0x94b70000] (64MB) mapped at [ffff880090b70000-ffff880094b6ffff]
    [ 0.665818] Simple Boot Flag at 0x44 set to 0x1
    [ 0.666015] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
    [ 0.666080] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x17
    [ 0.666087] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x17
    [ 0.666095] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x17
    [ 0.666104] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x17
    [ 0.666156] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 0.666187] Scanning for low memory corruption every 60 seconds
    [ 0.666541] futex hash table entries: 2048 (order: 5, 131072 bytes)
    [ 0.666577] Initialise system trusted keyring
    [ 0.666959] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.668721] zpool: loaded
    [ 0.668726] zbud: loaded
    [ 0.668990] VFS: Disk quotas dquot_6.5.2
    [ 0.669031] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.669172] msgmni has been set to 7751
    [ 0.669234] Key type big_key registered
    [ 0.669453] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.669499] io scheduler noop registered
    [ 0.669502] io scheduler deadline registered
    [ 0.669540] io scheduler cfq registered (default)
    [ 0.669759] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
    [ 0.669935] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
    [ 0.670110] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
    [ 0.670269] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X
    [ 0.670374] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
    [ 0.670379] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
    [ 0.670396] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
    [ 0.670398] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
    [ 0.670402] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
    [ 0.670419] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
    [ 0.670421] pci 0000:08:00.0: Signaling PME through PCIe PME interrupt
    [ 0.670424] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
    [ 0.670440] pcieport 0000:00:1c.3: Signaling PME through PCIe PME interrupt
    [ 0.670442] pci 0000:09:00.0: Signaling PME through PCIe PME interrupt
    [ 0.670446] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme loaded
    [ 0.670466] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.670499] pciehp 0000:00:1c.1:pcie04: Slot #1 AttnBtn- AttnInd- PwrInd- PwrCtrl- MRL- Interlock- NoCompl+ LLActRep+
    [ 0.670533] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded
    [ 0.670539] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.670583] efifb: probing for efifb
    [ 0.670605] efifb: framebuffer at 0xa0000000, mapped to 0xffffc90010800000, using 4160k, total 4160k
    [ 0.670606] efifb: mode is 1366x768x32, linelength=5504, pages=1
    [ 0.670607] efifb: scrolling: redraw
    [ 0.670609] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 0.674675] Console: switching to colour frame buffer device 170x48
    [ 0.678177] fb0: EFI VGA frame buffer device
    [ 0.678188] intel_idle: MWAIT substates: 0x11142120
    [ 0.678190] intel_idle: v0.4 model 0x45
    [ 0.678191] intel_idle: lapic_timer_reliable_states 0xffffffff
    [ 0.678506] GHES: HEST is not enabled!
    [ 0.678574] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.679056] Linux agpgart interface v0.103
    [ 0.679108] rtc_cmos 00:01: RTC can wake from S4
    [ 0.679243] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
    [ 0.679273] rtc_cmos 00:01: alarms up to one month, 242 bytes nvram, hpet irqs
    [ 0.679287] Intel P-state driver initializing.
    [ 0.679431] ledtrig-cpu: registered to indicate activity on CPUs
    [ 0.679696] TCP: cubic registered
    [ 0.679919] NET: Registered protocol family 10
    [ 0.680456] NET: Registered protocol family 17
    [ 0.681245] Loading compiled-in X.509 certificates
    [ 0.681277] registered taskstats version 1
    [ 0.682279] Magic number: 3:299:689
    [ 0.682435] rtc_cmos 00:01: setting system clock to 2015-02-08 15:39:50 UTC (1423409990)
    [ 0.682615] PM: Checking hibernation image partition UUID=38f5c3ea-1283-4a7e-a952-49dee4e9b5ae
    [ 0.682621] PM: Hibernation image not present or could not be loaded.
    [ 0.684595] Freeing unused kernel memory: 1160K (ffffffff818e5000 - ffffffff81a07000)
    [ 0.684599] Write protecting the kernel read-only data: 8192k
    [ 0.688817] Freeing unused kernel memory: 652K (ffff88000155d000 - ffff880001600000)
    [ 0.690614] Freeing unused kernel memory: 328K (ffff8800017ae000 - ffff880001800000)
    [ 0.702916] random: systemd-tmpfile urandom read with 3 bits of entropy available
    [ 0.718779] sdhci: Secure Digital Host Controller Interface driver
    [ 0.718781] sdhci: Copyright(c) Pierre Ossman
    [ 0.720168] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSS1] at 0x60,0x64 irq 1,12
    [ 0.726783] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.726825] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.727977] ACPI: bus type USB registered
    [ 0.727998] usbcore: registered new interface driver usbfs
    [ 0.728005] usbcore: registered new interface driver hub
    [ 0.728031] usbcore: registered new device driver usb
    [ 0.728826] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.728833] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
    [ 0.728904] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
    [ 0.728919] xhci_hcd 0000:00:14.0: irq 44 for MSI/MSI-X
    [ 0.729105] hub 1-0:1.0: USB hub found
    [ 0.729116] hub 1-0:1.0: 9 ports detected
    [ 0.729254] rtsx_pci 0000:02:00.0: irq 45 for MSI/MSI-X
    [ 0.729269] rtsx_pci 0000:02:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 45
    [ 0.729962] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.730134] ehci-pci: EHCI PCI platform driver
    [ 0.731658] SCSI subsystem initialized
    [ 0.732538] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.732545] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
    [ 0.732737] hub 2-0:1.0: USB hub found
    [ 0.732750] hub 2-0:1.0: 4 ports detected
    [ 0.733058] libata version 3.00 loaded.
    [ 0.733952] ehci-pci 0000:00:1d.0: EHCI Host Controller
    [ 0.733959] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 3
    [ 0.733972] ehci-pci 0000:00:1d.0: debug port 2
    [ 0.737882] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
    [ 0.737904] ehci-pci 0000:00:1d.0: irq 23, io mem 0xb261c000
    [ 0.747112] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
    [ 0.747298] hub 3-0:1.0: USB hub found
    [ 0.747312] hub 3-0:1.0: 2 ports detected
    [ 0.747491] ahci 0000:00:1f.2: version 3.0
    [ 0.747673] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X
    [ 0.747695] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
    [ 0.760531] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x3 impl SATA mode
    [ 0.760537] ahci 0000:00:1f.2: flags: 64bit ncq stag pm led clo only pio slum part deso sadm sds apst
    [ 0.761117] scsi host0: ahci
    [ 0.761280] scsi host1: ahci
    [ 0.761400] scsi host2: ahci
    [ 0.761527] scsi host3: ahci
    [ 0.761587] ata1: SATA max UDMA/133 abar m2048@0xb261b000 port 0xb261b100 irq 46
    [ 0.761590] ata2: SATA max UDMA/133 abar m2048@0xb261b000 port 0xb261b180 irq 46
    [ 0.761591] ata3: DUMMY
    [ 0.761592] ata4: DUMMY
    [ 0.763988] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 1.054094] usb 3-1: new high-speed USB device number 2 using ehci-pci
    [ 1.080772] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 1.090784] usb 1-3: new low-speed USB device number 2 using xhci_hcd
    [ 1.108052] ata1.00: ATA-8: ST500LT012-1DG142, 0002LVM1, max UDMA/133
    [ 1.108057] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
    [ 1.147102] ata1.00: configured for UDMA/133
    [ 1.147357] scsi 0:0:0:0: Direct-Access ATA ST500LT012-1DG14 LVM1 PQ: 0 ANSI: 5
    [ 1.178260] hub 3-1:1.0: USB hub found
    [ 1.178324] hub 3-1:1.0: 8 ports detected
    [ 1.267676] usb 1-3: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
    [ 1.269353] hidraw: raw HID events driver (C) Jiri Kosina
    [ 1.271432] usbcore: registered new interface driver usbhid
    [ 1.271435] usbhid: USB HID core driver
    [ 1.427737] usb 1-6: new high-speed USB device number 3 using xhci_hcd
    [ 1.467751] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 1.472648] ata2.00: ATAPI: PLDS DVD-RW DA8A5SH, RL61, max UDMA/100
    [ 1.473654] ata2.00: configured for UDMA/100
    [ 1.487478] scsi 1:0:0:0: CD-ROM PLDS DVD-RW DA8A5SH RL61 PQ: 0 ANSI: 5
    [ 1.506690] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
    [ 1.506695] sd 0:0:0:0: [sda] 4096-byte physical blocks
    [ 1.506762] sd 0:0:0:0: [sda] Write Protect is off
    [ 1.506765] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 1.506805] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 1.526586] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 1.526589] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 1.526753] sr 1:0:0:0: Attached scsi CD-ROM sr0
    [ 1.576727] sda: sda1 sda2 sda3 sda4
    [ 1.577520] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 1.668501] tsc: Refined TSC clocksource calibration: 2394.458 MHz
    [ 1.834689] usb 1-7: new full-speed USB device number 4 using xhci_hcd
    [ 1.866481] PM: Starting manual resume from disk
    [ 1.866486] PM: Hibernation image partition 8:2 present
    [ 1.866488] PM: Looking for hibernation image.
    [ 1.866742] PM: Image not found (code -22)
    [ 1.866745] PM: Hibernation image not present or could not be loaded.
    [ 2.008615] usb 1-7: No LPM exit latency info found, disabling LPM.
    [ 2.168326] usb 1-8: new full-speed USB device number 5 using xhci_hcd
    [ 2.200127] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    [ 2.668929] Switched to clocksource tsc
    [ 2.998993] random: nonblocking pool is initialized
    [ 5.035645] EXT4-fs (sda4): re-mounted. Opts: discard
    [ 7.983617] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 8.001442] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0C:00/input/input2
    [ 8.001451] ACPI: Power Button [PWRB]
    [ 8.001539] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/PNP0C0D:00/input/input3
    [ 8.001584] ACPI: Lid Switch [LID0]
    [ 8.001677] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
    [ 8.001681] ACPI: Power Button [PWRF]
    [ 8.067218] mei_me 0000:00:16.0: irq 47 for MSI/MSI-X
    [ 8.169733] thermal LNXTHERM:00: registered as thermal_zone0
    [ 8.169739] ACPI: Thermal Zone [TZ00] (29 C)
    [ 8.239918] ACPI: Battery Slot [BAT1] (battery present)
    [ 8.270385] ACPI: AC Adapter [ACAD] (on-line)
    [ 8.341145] [drm] Initialized drm 1.1.0 20060810
    [ 8.435780] ACPI Warning: SystemIO range 0x0000000000006040-0x000000000000605f conflicts with OpRegion 0x0000000000006040-0x000000000000604f (\_SB_.PCI0.SBUS.SMBI) (20140926/utaddress-258)
    [ 8.435788] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 8.524972] input: Ideapad extra buttons as /devices/pci0000:00/0000:00:1f.0/PNP0C09:00/VPC2004:00/input/input5
    [ 8.571862] [drm] Memory usable by graphics device = 2048M
    [ 8.571868] checking generic (a0000000 410000) vs hw (a0000000 10000000)
    [ 8.571870] fb: switching to inteldrmfb from EFI VGA
    [ 8.571892] Console: switching to colour dummy device 80x25
    [ 8.571969] [drm] Replacing VGA console driver
    [ 8.590169] i915 0000:00:02.0: irq 48 for MSI/MSI-X
    [ 8.590182] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [ 8.590184] [drm] Driver supports precise vblank timestamp query.
    [ 8.590211] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 8.648474] fbcon: inteldrmfb (fb0) is primary device
    [ 8.665898] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
    [ 8.665971] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
    [ 8.665996] [drm] Initialized i915 1.6.0 20140905 for 0000:00:02.0 on minor 0
    [ 8.789354] input: USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:0458:012B.0001/input/input7
    [ 8.789415] hid-generic 0003:0458:012B.0001: input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:14.0-3/input0
    [ 8.812071] media: Linux media interface: v0.10
    [ 8.833777] input: PC Speaker as /devices/platform/pcspkr/input/input9
    [ 8.840567] Linux video capture interface: v2.00
    [ 8.897231] uvcvideo: Found UVC 1.00 device Lenovo EasyCamera (0c45:6514)
    [ 8.929823] input: Lenovo EasyCamera as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/input/input10
    [ 8.929908] usbcore: registered new interface driver uvcvideo
    [ 8.929909] USB Video Class driver (1.1.1)
    [ 9.036891] cfg80211: Calling CRDA to update world regulatory domain
    [ 9.056738] Bluetooth: Core ver 2.19
    [ 9.056751] NET: Registered protocol family 31
    [ 9.056751] Bluetooth: HCI device and connection manager initialized
    [ 9.056757] Bluetooth: HCI socket layer initialized
    [ 9.056758] Bluetooth: L2CAP socket layer initialized
    [ 9.056766] Bluetooth: SCO socket layer initialized
    [ 9.348730] usbcore: registered new interface driver btusb
    [ 9.452303] iTCO_vendor_support: vendor-support=0
    [ 9.452955] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
    [ 9.452990] iTCO_wdt: Found a Lynx Point_LP TCO device (Version=2, TCOBASE=0x1860)
    [ 9.453081] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 9.494632] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
    [ 9.494637] r8169 0000:08:00.0: can't disable ASPM; OS doesn't have ASPM control
    [ 9.501333] r8169 0000:08:00.0: irq 49 for MSI/MSI-X
    [ 9.501800] r8169 0000:08:00.0 eth0: RTL8168g/8111g at 0xffffc90010788000, f0:76:1c:0c:12:99, XID 10900800 IRQ 49
    [ 9.501802] r8169 0000:08:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
    [ 9.582307] rtl8723be: Using firmware rtlwifi/rtl8723befw.bin
    [ 9.640127] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
    [ 9.640351] rtlwifi: rtlwifi: wireless switch is on
    [ 9.653001] mousedev: PS/2 mouse device common for all mice
    [ 9.667517] psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x2a800, board id: 2848, fw id: 1581875
    [ 9.686347] r8169 0000:08:00.0 enp8s0: renamed from eth0
    [ 9.708662] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
    [ 9.727739] Console: switching to colour frame buffer device 170x48
    [ 9.730327] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
    [ 9.730328] i915 0000:00:02.0: registered panic notifier
    [ 9.737976] snd_hda_intel 0000:00:1b.0: irq 50 for MSI/MSI-X
    [ 9.743445] AVX2 version of gcm_enc/dec engaged.
    [ 9.743448] AES CTR mode by8 optimization enabled
    [ 9.745577] snd_hda_intel 0000:00:03.0: irq 51 for MSI/MSI-X
    [ 10.040841] sound hdaudioC1D0: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
    [ 10.040848] sound hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
    [ 10.040851] sound hdaudioC1D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
    [ 10.040852] sound hdaudioC1D0: mono: mono_out=0x0
    [ 10.040854] sound hdaudioC1D0: inputs:
    [ 10.040857] sound hdaudioC1D0: Mic=0x19
    [ 10.040859] sound hdaudioC1D0: Internal Mic=0x12
    [ 10.046345] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input11
    [ 10.046446] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input12
    [ 10.046909] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input13
    [ 10.047361] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card1/hdaudioC1D0/input14
    [ 10.047575] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input15
    [ 10.047649] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input16
    [ 10.097496] rtl8723be 0000:09:00.0 wlp9s0: renamed from wlan0
    [ 10.655545] cfg80211: World regulatory domain updated:
    [ 10.655549] cfg80211: DFS Master region: unset
    [ 10.655550] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
    [ 10.655553] cfg80211: (2402000 KHz - 2472000 KHz @ 0 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.655555] cfg80211: (2457000 KHz - 2482000 KHz @ 0 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.655557] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.655559] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.655561] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    [ 10.655563] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    [ 10.655564] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.655566] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
    [ 10.732705] intel_rapl: Found RAPL domain package
    [ 10.732711] intel_rapl: Found RAPL domain core
    [ 10.732714] intel_rapl: Found RAPL domain uncore
    [ 10.732717] intel_rapl: Found RAPL domain dram
    [ 10.844302] Adding 4009760k swap on /dev/sda2. Priority:-1 extents:1 across:4009760k FS
    [ 13.353211] systemd-journald[146]: Received request to flush runtime journal from PID 1
    [ 18.647280] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [ 18.647284] Bluetooth: BNEP filters: protocol multicast
    [ 18.647293] Bluetooth: BNEP socket layer initialized
    [ 21.632791] r8169 0000:08:00.0 enp8s0: link down
    [ 83.137005] wlp9s0: authenticate with 00:1d:7e:6a:c4:67
    [ 83.729985] wlp9s0: send auth to 00:1d:7e:6a:c4:67 (try 1/3)
    [ 83.731584] wlp9s0: authenticated
    [ 83.731753] rtl8723be 0000:09:00.0 wlp9s0: disabling HT as WMM/QoS is not supported by the AP
    [ 83.731757] rtl8723be 0000:09:00.0 wlp9s0: disabling VHT as WMM/QoS is not supported by the AP
    [ 83.734174] wlp9s0: associate with 00:1d:7e:6a:c4:67 (try 1/3)
    [ 83.737516] wlp9s0: RX AssocResp from 00:1d:7e:6a:c4:67 (capab=0x411 status=0 aid=3)
    [ 83.737660] wlp9s0: associated
    [astinx@compu ~]$ systemctl status
    ● compu
    State: running
    Jobs: 0 queued
    Failed: 0 units
    Since: dom 2015-02-08 13:47:04 ART; 24min ago
    CGroup: /
    ├─1 /sbin/init
    ├─system.slice
    │ ├─dbus.service
    │ │ └─301 /usr/bin/dbus-daemon --system --address=systemd: --nofork --nopidfile --systemd-activation
    │ ├─org.cups.cupsd.service
    │ │ └─299 /usr/bin/cupsd -l
    │ ├─ModemManager.service
    │ │ └─303 /usr/bin/ModemManager
    │ ├─wpa_supplicant.service
    │ │ └─346 /usr/bin/wpa_supplicant -u
    │ ├─lightdm.service
    │ │ ├─314 /usr/bin/lightdm
    │ │ └─329 /usr/bin/Xorg.bin :0 -seat seat0 -auth /run/lightdm/root/:0 -nolisten tcp vt1 -novtswitch
    │ ├─accounts-daemon.service
    │ │ └─331 /usr/lib/accountsser

    So long I tried as Gusar said to loading the rtl8723b module with those params:
    sudo modprobe rtl8723be fwlps=0
    sudo modprobe rtl8723be ips=0
    So far by now, the connection hasn't dropped (one hour since I made the change)
    But is quite strange that when I do
    [astinx@compu ~]$ more /sys/module/rtl8723be/parameters/ips
    Y
    I mean, the parameters changed or not? I also tried with setting with N instead of 0.
    EDIT:
    The drop downs come back shortly after. I find quite strange that I cannot manage the power from iwconfig
    [astinx@compu ~]$ sudo iwconfig wlp9s0 power off
    [sudo] password for astinx:
    Error for wireless request "Set Power Management" (8B2C) :
    SET failed on device wlp9s0 ; Operation not supported.
    Last edited by astinx (2015-02-08 21:46:47)

  • Wireless guest access with CWA and ISE using mobility anchor

    My team is trying to demo wireless guest access using CWA with an ISE server.  We appear to be hitting an issue when combining this with mobility anchoring.
    When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound.  The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
    When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
    Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
    I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
    When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
    http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
    To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.

    FOREIGN
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 20) in 10 seconds
    *radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
    *radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
    MAC: 00:1e:c2:c0:96:05, source 2
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0,  mobility state = 'apfMsMmQueryRequested'
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0,  mobility state = 'apfMsMmQueryRequested'
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID = 255,
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   requested ip: 10.130.98.8
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0,  yiaddr: 10.130.98.8
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   siaddr: 10.30.4.173,  giaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   server id: 1.1.1.2  rcvd server id: 1.1.1.2
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
    *pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
    *pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
    MAC: 00:1e:c2:c0:96:05, source 2
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is  1
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 49) in 3600 seconds
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
    *apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
    *apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
    *pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4

  • CWA using ISE and mobility anchor

    My team is trying to demo wireless guest access using CWA with an ISE server.  We appear to be hitting an issue when combining this with mobility anchoring.
    When we don't use a mobility anchor the authentication goes off without a hitch seemingly proving that the ISE configuration is sound.  The test laptop associates and gets redirected, auths, moves to the RUN state and access to the network is granted.
    When the mobility anchor is enabled, the test laptop does get redirected, authentication is successful, but the process does not fully complete, as on the foreign controller the user is in RUN state whereas on the anchor the user is still stuck at CWA required.
    Now, I've read the L2 auth occurs between the foreign controller and ISE, and the L3 auth occurs between the anchor controller and ISE, but this does not appear to borne out in packet captures of the process where both parts of the auth seems to go to and from the foreign controller and ISE.
    I'm curious to know if anyone else has come across this issue, or has ideas where I should be looking in the config or debugs to find the root cause.
    When setting up the controllers and ISE this guide (linked below) was used and the controllers are 2504 controllers on 7.5 series software and ISE is on the latest 1.2 patches:
    http://www.cisco.com/en/US/products/ps11640/products_configuration_example09186a0080bead09.shtml
    To me it seems to be mobility related, but the authentication flow does seem to be off compared with what the guide says.

    FOREIGN
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Adding mobile on LWAPP AP 0c:d9:96:ba:7d:20(1)
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Association received from mobile on BSSID 0c:d9:96:ba:7d:2f
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 Re-applying interface policy for client
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
    *apfMsConnTask_4: Jan 28 23:04:59.525: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4565 setting Central switched to TRUE
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 In processSsidIE:4568 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying site-specific Local Bridging override for station 00:1e:c2:c0:96:05 - vapId 1, site 'AP-Group-CHEC.default', interface 'management'
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Applying Local Bridging Interface Policy for station 00:1e:c2:c0:96:05 - vlan 84, interface id 0, interface 'management'
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 apfProcessAssocReq (apf_80211.c:7830) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Idle to AAA Pending
    *apfMsConnTask_4: Jan 28 23:04:59.526: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 20) in 10 seconds
    *radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created for mobile, length = 253
    *radiusTransportThread: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Username entry (00-1E-C2-C0-96-05) created in mscb for mobile, length = 253
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Received SGT for this Client.
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Redirect URL received for client from RADIUS. Client will be moved to WebAuth_Reqd state to facilitate redirection. Skip web-auth Flag = 0
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 255 to 255
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 84
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 Re-applying interface policy for client
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
    *apfReceiveTask: Jan 28 23:04:59.550: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 0 on mobile
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
    MAC: 00:1e:c2:c0:96:05, source 2
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Initializing policy
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfMsAssoStateInc
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
    *apfReceiveTask: Jan 28 23:04:59.551: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:04:59.567: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0,  mobility state = 'apfMsMmQueryRequested'
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:05:01.523: 00:1e:c2:c0:96:05 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0,  mobility state = 'apfMsMmQueryRequested'
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=ExpForeign, client state=APF_MS_STATE_ASSOCIATED
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 apfMsRunStateInc
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 DHCP_REQD (7) Change state to RUN (20) last state DHCP_REQD (7)
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Reached PLUMBFASTPATH: from line 5793
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Adding Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID = 255,
    *mmMaListen: Jan 28 23:05:02.362: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *mmMaListen: Jan 28 23:05:02.363: 00:1e:c2:c0:96:05 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
    *pemReceiveTask: Jan 28 23:05:02.364: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 0.0.0.0 plumbing in FP SCB
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP received op BOOTREQUEST (1) (len 308,vlan 84, port 13, encap 0xec03)
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP (encap type 0xec03) mstype 0ff:ff:ff:ff:ff:ff
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP processing DHCP REQUEST (3)
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 5, flags: 0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   siaddr: 0.0.0.0,  giaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.869: 00:1e:c2:c0:96:05 DHCP   requested ip: 10.130.98.8
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP received op BOOTREPLY (2) (len 320,vlan 84, port 13, encap 0xec07)
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP processing DHCP ACK (5)
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   xid: 0xafea6bc9 (2951375817), secs: 0, flags: 0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   chaddr: 00:1e:c2:c0:96:05
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   ciaddr: 0.0.0.0,  yiaddr: 10.130.98.8
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   siaddr: 10.30.4.173,  giaddr: 0.0.0.0
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 DHCP   server id: 1.1.1.2  rcvd server id: 1.1.1.2
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) DHCP Address Re-established
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Reached PLUMBFASTPATH: from line 6978
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID
    *DHCP Socket Task: Jan 28 23:05:03.887: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 Assigning Address 10.130.98.8 to mobile
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Jan 28 23:05:03.888: 00:1e:c2:c0:96:05 DHCP successfully bridged packet to STA
    *pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:03.889: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4
    *pemReceiveTask: Jan 28 23:05:03.890: 00:1e:c2:c0:96:05 Skip Foreign / Export Foreign Client IP 10.130.98.8 plumbing in FP SCB
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Received SGT for this Client.
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 acl from 0 to 255
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Resetting web IPv4 Flex acl from 65535 to 65535
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 AAA redirect is NULL. Skipping Web-auth for Radius NAC enabled WLAN.
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfReceiveTask: Jan 28 23:05:18.716: 00:1e:c2:c0:96:05 Inserting AAA Override struct for mobile
    MAC: 00:1e:c2:c0:96:05, source 2
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Applying cached RADIUS Override values for mobile 00:1e:c2:c0:96:05 (caller pem_api.c:2307)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Setting session timeout 3600 on mobile 00:1e:c2:c0:96:05
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Session Timeout is 3600 - starting session timer for the mobile
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Applied RADIUS override policy
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Replacing Fast Path rule
      type = Airespace AP Client
      on AP 0c:d9:96:ba:7d:20, slot 1, interface = 13, QOS = 0
      IPv4 ACL ID = 255, IPv6 ACL ID
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 84, Local Bridging intf id = 0
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Not Using WMM Compliance code qosCap 00
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Plumbed mobile LWAPP rule on AP 0c:d9:96:ba:7d:20 vapId 1 apVapId 1 flex-acl-name:
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 10.130.98.8 RUN (20) Change state to RUN (20) last state RUN (20)
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfMsAssoStateInc
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from AAA Pending to Associated
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 apfPemAddUser2:session timeout forstation 00:1e:c2:c0:96:05 - Session Tout 3600, apfMsTimeOut '1800' and sessionTimerRunning flag is  1
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Scheduling deletion of Mobile Station:  (callerId: 49) in 3600 seconds
    *apfReceiveTask: Jan 28 23:05:18.717: 00:1e:c2:c0:96:05 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 3600
    *apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 Sending Assoc Response to station on BSSID 0c:d9:96:ba:7d:2f (status 0) ApVapId 1 Slot 1
    *apfReceiveTask: Jan 28 23:05:18.718: 00:1e:c2:c0:96:05 apfProcessRadiusAssocResp (apf_80211.c:3066) Changing state for mobile 00:1e:c2:c0:96:05 on AP 0c:d9:96:ba:7d:20 from Associated to Associated
    *pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 Set bi-dir guest tunnel for 00:1e:c2:c0:96:05 as in Export Foreign role
    *pemReceiveTask: Jan 28 23:05:18.720: 00:1e:c2:c0:96:05 10.130.98.8 Added NPU entry of type 1, dtlFlags 0x4

  • Internet Connection Drop Outs when remote administ...

    I did not want to trouble anyone here if I thought it unnecessary but now I feel that I do need some assistance so this warrants opening a new thread.
    BT Infinity Option 2 customer with BT HH 4 and its separate modem - not hacked so cannot read any useful information or login to see what is going on and both BT and the manufacturer long ago removed the open source code of the modem.
    I am quite confident now that these disconnections happen when a remote server/attacker attempts to gain access to my network. These can be from China, Iran and other places too. Sometimes Ministry of Defence? I don't know why I get these connection attempts and most of the time I see BT HH 4 does block these so why I get disconnected I have no idea?
    I made a post in an old thread before opening this thread and said it was due to firmware upgrade but I misread the date! It was not updated since the 8th of May I think. These disconnections have been happening only this past 4-7 days with the most 4 days with intensity greater than the 3 before. I am not 100% certain it is caused by the remote administration that is blocked.
    What happens when this takes place is the BT servers are then unreachable sometimes and I cannot regain a connection for up to 3 hours at a time, usually it is 5-10 mins max though. Without looking at my event log, any ideas?
    I want to get different gear now and never wanted to use BT equipment anyway because I want greater control and options to configure. I would like to go with DD-WRT or OpenWRT Router with Integrated VDSL v2 modem. Anyone here that may suggest one that supports either of these open firmwares? Not so much the concern to prevent any security holes or backdoors but just as much if not more for versatility and configuration and just having control over my network. being able to do upgrades when I want and not when my ISP decides needs doing. And before you say BT do not have backdoors then why would they admit they can remote login to devices and storage contents with their pwerline adapters even. I remember reading a news article quoting BT as admiting this. Anyway, that is not my main concern here, as much as privacy and security is not a crime it is rather rare online. First I need to get to the root cause of this.
    BT HH 4 is not reporting any DDOS attacks and even if it were I would not expect to experience any disconnection. I used to get tons of floods from DDOS attacks years ago when using Netgear routers and never exeprienced any downtime, but that was with another ISP. I don't detect any malware or anything like that and rarely download anything on this machine, I know web browsing can infect a system but I don't think that is it.
    I want to go back to how I used to do things. Any help with this is appreciated. I will need to get my router login details because I was never given those when I singed up with BT Infinity Option 2. I don't even know what my BT email is but do believe there is a way to recover that under my account. **In the past we have had intermittent connection drops and loss of sync but this is not the same right now.
    Edit:
    ** Just to clarify that was before we upgraded to BT Infinity Opt 2. This is the first time any probs with this service since upgrade and that must be about 6 months or more now.

    When running BT HH diagnostic it printed out that the username for login had changed and needed resetting or for me to enter my own in that I was NOT given! Anyway, when going to select manual reset it had not changed from default at all so I think this is just some default BT diagnostic that is false. I realise that other BT customers are affected by this with the BT HH5 but mine is HH4...my posting probably isn't as clear right now as I have not slept as much past few nights trying to figure this out. This is happening at different times of the day but more often during early hours.
    So I am getting these WGET TLS error(s)
    How do I enter in log excerpt from BT HH? Forums says my post exceeds 20K chars...

  • BT Infinity Connection Dropping but BT refuse to a...

    Hi,
    So in September we got BT Infinity. It was a hassle and handled terribly by BT customer service but we eventually got it. It's been working fine for around five months but within the last few weeks we have been having connection issues.
    Over Easter I have spent over 10 hours on the phone to BT via my landline and mobile trying to get a solution, but all I have got is a repeated denial of my problems.
    On the 27th March I called BT to report that our connection had been repeatedly dropping over the past few weeks and a fault was opened. I was told I would be updated but no-one called back despite promises they would do.
    I called BT on the 28th March to follow up my issues but was met with an advisor who lacked knowledge in the issue and simply told me to continue monitoring my connection.
    I called BT on the 3rd April as there had been no improvement in my connection, which is dropping multiple times per day, and on this day 7 times. After going through the same repetitive questioning session about how I connect to the internet, a deep line test was run, and it was decisively concluded that there was a fault with the line within BT's retail servers. I was told this would be followed up and promised a call back on the 4th April.
    After I had not received a call back on the 4th April within the time allocated to me, I called BT where I was met with an awfully rude woman who had no interest in helping me and went on to suggest what I was saying was an outright lie and she categorically stated there had been no call back booked despite me having the text in front of me which confirmed it.
    After being told to 'continue monitoring my line', a slightly repetitive phrase favoured by BT Customer Service, I called back as instructed on the 8th April. Again, I went through a repetitive process before finally making some sort of progress and being sent a new home hub.
    My new home hub arrived on the 11th April and made no difference to my problem. I therefore called BT and spoke to an advisor who told me he could only assume the Home Hub was sent in error, as he was absolutely adamant it would make absolutely no difference to my situation. I was told to 'continue monitoring my connection' over the next few days but before he ended the call I asked him a number of questions, none of which were adequately answered.
    Why is our connection dropping? Rather than giving me an explanation as to why it is dropping, he told me that we are lucky it only drops a few times a day! He said 'everyone in the world suffers from a connection which drops multiple times per day' and that 'there is absolutely nothing we can do because there is no problem'. He told me about rate-adaptive lines, which according to him 'are used by every household in the world' and that these lines 'inevitably drop out up to five times a day, which is normal and acceptable'.
    So how many times can it drop before it's considered a fault? The basic answer I received is that there is no limit! It doesn't matter how many times it drops, it absolutely normal! Only if it drops '20-30+ times per day' is it considered a problem worth solving to BT.
    Why do you never call back (in particular, why did no-one call back on the 4th April, and why did an advisor accuse me of lying about the call back)? They said that when the issue is escalated from Level 1 to Level 2, it is impossible to see any contact between the customer and Level 1, so when the call back wasn't arranged as it should've been, there was no way BT could've known. He apologised for this and the way I was treated by his colleague.
    Why was a fault reported on the 3rd April? Why have I not been updated since? Simple answer from BT. There probably was no fault, that was probably also incorrectly opened. Note the key word probably. The advisor I talked to said he had no idea what happened in any of my previous calls and that there was no way he could find out why the fault was opened, or listen to the call (despite all calls being recorded). He said it was impossible for Level 2 to hear the content of any calls made with Level 1 and that it was 'impossible for an advisor to take notes for a call lasting more than half an hour'.
    I recieved a call back today on my mobile where I was told just to continue monitoring the fault. However I was also told, again, quite categorically, that there is nothing wrong and that he would happily send an engineer in three days but that 'he would be able to do absolutely nothing. It would be a waste of time'. The advisor also refused to give any details on how much this would cost and was desperate to end the call saying 'goodbye' despite me being mid sentence multiple times.
    I have now been told to 'continue monitoring my connection' and await another call back on Friday, by which point I will have wasted many more hours on the phone to BT.
    Your customer service is disgusting. Your lack of compassion and understanding is disgusting. The way you totally mislead customers is disgusting.
    And now for my top BT Operator quotes (or near quotes, as obviously no-one has any idea what was said in these calls, not even BT!):
    "If your temperature raised to 100 degrees celcius but then went back to normal, there would be no problem, it's the same with broadband"
    "Everyone in the world has a rate-adaptive line and everyone in the world should expect their line to drop"
    "If your line only drops 5 or 6 times a day there is no problem, you obviously should've known this before you signed up for Infinity"
    "There definitely is a fault.... there definitely isn't a fault" - the trademark conclusiveness of BT
    "We can limit the speed on the phone line, but it would have to be to 1mb" - this is despite absolutely contradictory help published by BT
    But despite these humorous moments, I have wasted a huge amount of time on the phone to BT.
    I have one simple demand. Stop the broadband from dropping multiple times per day. If you cannot do this, let us leave, as you are not meeting your contractual obligations and therefore we shouldn't have to either.
    And please... don't apologise for your colleague not calling back in the first minute of the phone call and then not call back.

    Hi Bryan,
    Like yourself and many, many other people who come to these forums - I have been experiencing the same problems. Constant disconnections, and recently, speed dropping to 4Mb in the Evenings (I'm supposed to be getting 74Mb).
    It's ridiculous with how many people are experiencing these problems and BT are blatently ignoring it. To add insult to injury, this was posted in February. A statement from BT basically saying "Well you're all gonna be having problems, but it's on you."
    Don't fret though, the moderators, and other people from the community can be fantastic help.
    Purchasing an Openreach modem, suggested by ray_dorset, I'll still be awaiting for the Huawei 612, V3b modem to arrive and hoping this will fix the drops in speed. I currently have an ECI modem fitted in, which has stopped the disconnects, but have not stopped the speed drops.
    For anyone reading this who is unfamiliar with modems as I was:
    As far as I know, there's currently two types of Openreach Modems. Every exchange is built with a certain "chipset" which will work best with these modems (explaining in simplistic terms and I could be very wrong, so I am happy to be corrected.)
    The Two Openreach Modems:
    Huawei 614
    ECI
    From the advice I have been given by the moderators, if you're new to BT Infinity, then your exchange may have only recently been built, which is then most likely to have a chipset which will work better with Huawei modems. I'm about to find out this by next week.
    If, in some horrible scenario it doesn't work and the speed is still constantly dropping, then you may need to fork out and purchase a new router (BUT KEEP THE MODEM). Many people have said their internet has been fixed by doing this.
    One of the things I did find pretty hillarious however, is that I did call up BT the other night due to having terrible connections. He told me to take out my modem and just use the home hub 5. He then kept telling me to change a few settings on the HH5 and run a speedtest. Every, single, time we changed something - the speed would get lower and lower, followed by an "Uhhh, monitor your speed over the course of this week and then we'll call you back."
    I'm sorry, but BT customer service have no idea how to fix this, so don't waste your time ringing them. I genuinely feel bad for them too, they have to put up with our **bleep** while the engineers at BT who work on the firmware for the HH5 can't be arsed to try and fix it any further.
    Seriously, mate - just try the steps above, come to the forums if you need help because you're more than likely to get a better answer. I know it sucks not being able to call up BT because they're just going to give you a bunch of BS, but if everyone who had a complaint on this forum worked for BT tech support, maybe there'd be more satisfied customers.

  • Mac OS X lion 10.7.3 Wi-Fi connection Drop Issue

    Hi All,
      I've iMAC OS X Lion 10.7.3 latest version desktop. For couple of months, I'm dealing with dropping wi-fi connection during working. I've look at all the forums and discussions and tried many things to solve the issuse, however, issue still exist.
       Every a few minutes, even during surfing though internet pages, wi-fi connection drops. When you look at the signal level etc.. everything is seems to be fine, but it is not possible to connect internet after close-open wi-fi.
       For a while, connection drop happens again.
       I do not understand why Apple does not give a fix for this while most the customer having such an issue.
      Any one having any idea how to solve this ?
    Regards
    Gokcer

    I have a similar problem.  My Macbook Pro won't keep a constant wi-fi connection, becuase it continues to seek alternative networks even after locking onto a strong signal.  I've reset preferences and started from scratch with all the settings and let the Mac set them by itself, but still it does the seeking.  At home I used to have a direct LAN into my Airport Extreme, but now I use wi-fi on 4G/LTE and I've tried the computer with and without the Airport Extreme, with and without a Cradlepoint, and with various channels and security levels. 
    As has been document probably hundreds of times in these forums, Macbook Pros (my model) and some other Macs have had this issue from either 10.7.2 or 10.7.3 (I've got 10.7.4 right now).  I'm glad you found a solution to your problem, but for the hundreds or thousands of us who've had this problem since last August with no solution from Apple, it's quite frustrating.  I know it's not politically correct to blame the computer when it's been given a defective upgrade with Lion, but let's call it what it is.  I'll side with the numbers.  Either a sudden batch of defective routers showed up from Taiwan, and a group of late 2008 and 2009 Macbook Pros bought them all en masse, or it's the software. 
    So if you still have problems after you get a clear signal, start sending messages to Apple to get it fixed for all of us.  I bring this up for you as an alternative, as I noticed you were running 10.7.3, and the problems started somewhere around 10.7.2 or 10.7.3.  Something to keep an eye on. 

  • Email Stuck - SMTP Relay To Remote Active Directory Site 451 4.4.0 Primary target IP address responded with: ""421 4.4.2 Connection dropped due to SocketError

    hi All, 
    I have 2 HT, located different AD Site. HT1 located in HO Site, and HT2 located in Branch Site.
    User from HO site can send email to branch site, but user from branch site cannot send email to HO site.
    I found this error on Queue Viewer Console:
    451 4.4.0 Primary target IP address responded with: ""421 4.4.2 Connection dropped due to SocketError."" Attempted failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed
    to all alternate hosts
    disable all receive connector except default connector still no luck. Telnet SMTP to HT1 from HT2 is working fine.
    Event Viewer warning, event ID: 2006.
    Send connector Intra-Organization SMTP Send Connector: the connection to IPHT1:25 was disconnected by the remote server.
    Send SMTP Log:
    2014-03-10T07:11:50.624Z,Intra-Organization SMTP Send Connector,08D109CB5D495BDE,19,IPHT2:57231,IPHT1:25,-,,Remote
    2014-03-10T07:21:50.716Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,0,,IPHT1:25,*,,attempting to connect
    2014-03-10T07:21:50.763Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,1,IPHT2:15741,IPHT1:25,+,,
    2014-03-10T07:21:50.825Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,2,IPHT2:15741,IPHT1:25,<,"220 IPHT1.jakarta.com Microsoft ESMTP MAIL Service ready at Mon, 10 Mar 2014 14:21:50 +0700",
    2014-03-10T07:21:50.825Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,3,IPHT2:15741,IPHT1:25,>,EHLO IPHT2.jakarta.com,
    2014-03-10T07:21:50.872Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,4,IPHT2:15741,IPHT1:25,<,250-IPHT1.jakarta.com Hello [IPHT2],
    2014-03-10T07:21:50.872Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,5,IPHT2:15741,IPHT1:25,<,250-SIZE 104857600,
    2014-03-10T07:21:50.872Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,6,IPHT2:15741,IPHT1:25,<,250-DSN,
    2014-03-10T07:21:50.872Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,7,IPHT2:15741,IPHT1:25,<,250-ENHANCEDSTATUSCODES,
    2014-03-10T07:21:50.872Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,8,IPHT2:15741,IPHT1:25,<,250-STARTTLS,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,9,IPHT2:15741,IPHT1:25,<,250-X-ANONYMOUSTLS,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,10,IPHT2:15741,IPHT1:25,<,250-AUTH NTLM,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,11,IPHT2:15741,IPHT1:25,<,250-X-EXPS GSSAPI NTLM,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,12,IPHT2:15741,IPHT1:25,<,250-8BITMIME,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,13,IPHT2:15741,IPHT1:25,<,250-BINARYMIME,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,14,IPHT2:15741,IPHT1:25,<,250-XEXCH50,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,15,IPHT2:15741,IPHT1:25,<,250-XRDST,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,16,IPHT2:15741,IPHT1:25,<,250 XSHADOW,
    2014-03-10T07:21:51.091Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,17,IPHT2:15741,IPHT1:25,>,X-ANONYMOUSTLS,
    2014-03-10T07:21:51.122Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,18,IPHT2:15741,IPHT1:25,<,220 2.0.0 SMTP server ready,
    2014-03-10T07:26:51.590Z,Intra-Organization SMTP Send Connector,08D109CB5D495C06,19,IPHT2:15741,IPHT1:25,-,,Remote
    2014-03-10T07:26:51.590Z,Intra-Organization SMTP Send Connector,08D109CB5D495C0E,0,,IPHT1:25,*,,attempting to connect
    2014-03-10T07:26:51.636Z,Intra-Organization SMTP Send Connector,08D109CB5D495C0E,1,IPHT2:15794,IPHT1:25,+,,
    anyone have a clue?
    thanks.
    Endrik
    Endrik | blog: itendrik.wordpress.com Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
    the thread.

    Hi Niko, 
    I already disable IPv6 and IPv4 checksum offloading, also check the MTU on each HT but still no luck.
    I found the following error on the Netmon:
    i already tls on receive connector, enable anonymous authentication, still no luck.
    any idea?
    thanks.
    Endrik
    Endrik | blog: itendrik.wordpress.com Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
    the thread.

  • Connection drops on a daily basis / Varying (low) ...

    People probably know the drill by now, everything is fine then suddenly they go through a period where they receive barely a 10th of their paid connection speed, with their connection dropping completely at least once per day.
    This all started happening when BT somehow increased our connection speed from 8Mbps to 21Mbps and also increased our upload from about 250kbps to 1Mbps which happened a couple months ago now. This was great! Everything was working fine, no drops in the connection or speed and it seemed like they had given us a nice boost for free.
    That is, until things started going wrong about a month later when our connection would frequently drop, the connection speed would often fall to below 1Mbps and this is still happening.
    With regards to solving this problem myself, I don't see how anything could be interfering with the setup I currently have, as nothing has changed within the house itself. Before I ring up an Indian/ Chinese/ Scottish/ Martian call center, I'd like to try and get some feedback from the users on this forum.
    I'm going to buy some new ADSL filters just to see if the ones I'm currently using are packing up (they're cheap so that is no problem if nothing changes).
    I have run quite a few speedtests using the recommended btspeedtester and have had varying results, all of which barely, if at all, meeting the acceptable range of speed for my line. Here is my most recent test:
     Download speedachieved during the test was - 4563 Kbps
     For your connection, the acceptable range of speeds is 4000-21000 Kbps.
     IP Profile for your line is - 11000 Kbps
    Some additional info on my connection:
    ADSL line status
    Connection time
    0 days, 00:46:06
    Downstream
    12,651 Kbps
    Upstream
    1,260 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.5 Annex A
    Latency type
    Interleaved
    Noise margin (Down/Up)
    6.8 dB / 6.5 dB
    Line attenuation (Down/Up)
    18.3 dB / 8.9 dB
    Output power (Down/Up)
    20.2 dBm / 1.9 dBm
    Loss of Framing (Local/Remote)
    0 / 0
    Loss of Signal (Local/Remote)
    0 / 0
    Loss of Power (Local/Remote)
    0 / 0
    FEC Errors (Down/Up)
    2101 / 817
    CRC Errors (Down/Up)
    33376 / 1808
    HEC Errors (Down/Up)
    262820 / 0
    Error Seconds (Local/Remote)
    2101 / 771

    Thanks again for the reply.
    I connected to the test socket and saw a difference straight away when my internet reconnected. I ran another btspeedtest and here are the results:
     Download speedachieved during the test was - 8610 Kbps
     For your connection, the acceptable range of speeds is 4000-21000 Kbps.
     IP Profile for your line is - 11000 Kbps
    ADSL line status
    Connection Information
    Connection time
    0 days, 00:11:22
    Downstream
    13,838 Kbps
    Upstream
    1,272 Kbps
    ADSL Settings
    VPI/VCI
    0/38
    Type
    PPPoA
    Modulation
    G.992.5 Annex A
    Latency type
    Interleaved
    Noise margin (Down/Up)
    6.3 dB / 6.3 dB
    Line attenuation (Down/Up)
    18.2 dB / 8.9 dB
    Output power (Down/Up)
    21.5 dBm / 1.9 dBm
    Loss of Framing (Local/Remote)
    0 / 0
    Loss of Signal (Local/Remote)
    0 / 0
    Loss of Power (Local/Remote)
    0 / 0
    FEC Errors (Down/Up)
    676 / 0
    CRC Errors (Down/Up)
    5613 / 160
    HEC Errors (Down/Up)
    60095 / 0
    Error Seconds (Local/Remote)
    676 / 100
    I don't suppose it's possible to simply leave things as they are connected to the test socket?

  • Wireless connection drops and doesn't reconnect (netcfg, wpa_actiond)

    I use netcfg 2.5.4-1 and wpa_actiond 1.1-1, B43 driver (BCM4318 wireless card) with firmware.
    $ uname -a
    Linux vekta 2.6.32-ARCH #1 SMP PREEMPT Mon Mar 15 20:08:25 UTC 2010 i686 Mobile AMD Sempron(tm) Processor 3100+ AuthenticAMD GNU/Linux
    Connecting works fine. I can connect using sudo netcfg <profile>, or it automatically connects me on startup.
    However, after a few minutes (up to 15 at best, usually 3-5) the connection is dropped. dmesg prints:
    "No probe response from AP <macaddress> after 500ms, disconnecting."
    However, netcfg isn't notified of this event, and still thinks the profile is connected. So I have to use netcfg -r <profile> to reconnect. Isn't netcfg supposed to notice this connection drop and try to reconnect again automatically?
    Also, is there any way to increase the 500ms threshold mentioned in the log? I don't think I ever had this problem when I first installed arch in november/december last year.
    Thank you.

    geniuz wrote:
    Hey,
    I'm having this sort of problem with my Broadcom wireless card, in my case however the connection seems to drop after a period of inactivity. What you have done might solve my problem. So exactly what modification have you made in netcfg ?
    This is the patch I made;
    diff --git a/src/globals b/src/globals
    index 2d5cf19..dcffea3 100644
    --- a/src/globals
    +++ b/src/globals
    @@ -15,7 +15,7 @@ SUBR_DIR="/usr/lib/network/"
    HOOKS_DIR="${SUBR_DIR}/hooks/"
    CONN_DIR="${SUBR_DIR}/connections/"
    STATE_DIR="/var/run/network/"
    +AUTOWIRELESS_DIR="/etc/rc.d/"
    ### Logging/Error reporting
    diff --git a/wpa_actiond/netcfg-wpa_actiond-action b/wpa_actiond/netcfg-wpa_actiond-action
    index 3547fef..324d990 100755
    --- a/wpa_actiond/netcfg-wpa_actiond-action
    +++ b/wpa_actiond/netcfg-wpa_actiond-action
    @@ -42,7 +42,12 @@ case $action in
             fi
             set_profile down "$profile"
    -    LOST|REESTABLISHED)
    +    LOST)
    +        if ! "$AUTOWIRELESS_DIR/net-auto-wireless" restart; then
    +            exit 1
    +        fi
    +        ;;
    +    REESTABLISHED)
             # Not handled.
             exit 0

  • DHCP issue with mobility anchor

    Hi Guys,
    I am having a bit of trouble to get the DHCP to work in my configuration. basically I have configured one SSID on two WLCs (running same version of code), I configured WLC 1 as anchor  controller and configured itself as mobility anchor (local), and on foreign controller (WLC2), I have configured the anchor as a mobility anchor. I have added both of the WLCs in each other's mobility list, however WLC1 and 2 are not in the same mobility group. clients are getting IP address through an external DHCP server.
    the problem is that when I used the management interface for the WLAN, I could get IP address through DHCP without any problem, however if I use another dynamic interface created for the SSID, then I could not get IP address anymore. I did another test with two WLCs configured in the same mobility group, then everythnig works fine. I have double checked my configuration for the dynamic interface but could not find anything wrong.
    so my question is
    is it possible to do auto anchoring configuration with two WLCs in different mobility group (different mobility group name), since based on my test management interface works,  but another dynamic interface did not work. in the configuration guide, it says: "you must add controllers to the mobility group member list before you can designate them as mobiolity anchors for a WLAN", does that mean the mobility group name has to be the same for both of the WLCs? if that's the case why does management interface worked?
    thanks in advance for you help.

    Hi Nicolas,
    thanks for your reply, i guess that's where the problem is - I could not ping the dynamic interface from the DHCP server. (eping and mping works fine)
    however I could ping the dynamic interface of the foreign controller (i have created another dynamic interface on the same subnet on the foreign controller, i understand it's not really necessary since we getting IP in the range defined on the anchor controller). the only difference between the two controllers is that the foreign controller enabled LAG, and only connected to the core swithc number 1, but the anchor controlelr is not (it has two connections to two core switches respectively).
    so does this mean I can not use this controller to be a anchor controller if it has two connections to two differnet switches? if yes is there any documentation on this point?
    Thanks very much for your help.

Maybe you are looking for