Modbus errors when making object connection
I have a telemetry system that currently has 37 RTU's and uses Lookout 6.0.2. We are adding an additional site ( pump station with controls) and I am experiencing a probleml when making the "connection" between a control object (00001) and a switch. With the RTU up and running without the switch connection, modbus statistics show valid response frames at 100% with no errors. Input states can be changed and the software works properly and dispays the correct state. AS SOON as I make the connection between the control object and the switch, modbus statistics show "no response" errors immediately and the software X's out all of the dispayed objects for that RTU. If I change the switch position, the RTU responds and turns on or off the corresponding output even though the software says the RTU in not responding. I have tried creating a new modbus driver and making a simple connection between a control object and a switch with the same result. If I re-address my RTU to a lower number that is not in use, such as 13, everything works normally. I do not have the luxury of just going to a lower number as the system is currently undergoing expansion and will continue to grow beyond the mark of 40 units in the field. Anybody seen this before?
Thanks
Brad Adams
Service Manager
CommTech
441 Donelson Pike, Suite 420
Nashville, TN 37214
Phone: 615-889-4756
Fax: 615-391-0300
Cell: 615-477-8975
[email protected]
"once you eliminate all other possibilities, what's left, however improbable, must be the solution"
Are you using serial modbus ASCII, RTU or TCPIP? Also, what type of radios are you using? I have noticed some errors with MDS radios when attempting to pass some binary codes through them.
Similar Messages
-
Adobe Forms Error Message 'Error when transforming object data'
Hi,
When i tried to save(Adobe Forms) after making changes in Layout its giving an error message 'Error when transforming object data' and takes me out of the transaction. How do i solve this ? Can anyone help me out.
Thanks and Regards,
Franklin.hi
I have the same problem , plz help me out
thanks -
I keep getting an unknown error when trying to connect to the store. I ran diagnostics and it says secure link to itunes store failed. I've tried all suggestions from apple and nothing will work.
Please HelpI received this email from Apple and this corrected the problem for me... I only had to reset the iTunes cache
1) Open iTunes
2) At the top menu, click File > Preferences (iTunes > Preferences on a Mac)
3) In the Preferences menu, click the Advanced tab
4) In the Advanced menu, you should see a button that says "Reset Cache". Please click this button. -
Getting Error when trying to connect to the Primavera database. PPM V7 SP3
Hi Guys,
Caused by: org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'mailService' defined in class path resource [com/primavera/bre//com/primavera/bre/integration/intgconf.xml]: Invalid destruction signature; nested exception is org.springframework.beans.factory.support.BeanDefinitionValidationException: Couldn't find a destroy method named 'destroy' on bean with name 'mailService'
I have looked into the intgserver.jar under P6IntegrationAPI/lib and looked the com.primavera.infr.srvcs.MailServiceImpl.java and can see that there is no destroy method whereas it is defined in the com.primavera.bre.intergration.intgconf.xml as below
<!-- provides mail services -->
<bean id="mailService" class="com.primavera.infr.srvcs.MailServiceImpl" init-method="init" scope="singleton" destroy-method="destroy"*+>
<property name="adminManager"><ref bean="adminManager"/></property>
<property name="threadPool"><ref bean="threadPool"/></property>
<property name="settingsManager"><ref bean="settingsManager"/></property>
</bean>
I get the above error when trying to connect to the Primavera database. I use PPMV7 SP3 and I have installed the Integration API from EPPMV7 bundle.
My demo's are working fine.
Any help would be appreciated.
Thanks,
Kajal.Hi Marc,
I am using a userid (is an admin)
Using global login method and provided userid & password in integration settings.
In the machine profiles, provided userid, password and domin.
Not providing domain in weblogin.
With all the above I am still getting error "Could not authenticate the specified user. %0" for HFM application
And with the same settings I am not getting any error to connect to essbase cube.
Any suggestions?
Thanks
Krishna -
Hi
I am running on NW04s. Working on WD for ABAP Interactive forms. whenever I open the Adobe editor thru SFP or Se80, the editor opens up and I am able to do my operations. The moement I hit back button/Save or any other action which involves coming out of the adobe editor, it throws me an Fatal error - <b>Error when transforming object data</b>. I find that in most of the threads there are similar issues which are still open. Any Help would be appreciated.
I have installed ADLC 7.1, xACF04s.
Murali.I did the same installation on another PC, and to my suprise it works fine. Looks very strange
-
Error when opening RFC Connection
Hello SAPers,
I have configured PDA in my ECC6.0 --- XI (ABAP+JAVA) Which was successful.
In my Web Dyno Pro Content Administrator
I have performed the JCO Destinations test which was successful
when I go to the URL
http://server:port/webdynpro/dispatcher/sap.com/isisrsrsmenapp/MainApp
entered the store number
In the next menu
Inventory Lookup when I enter the Article number and press Go Button
It is giving me error " Error when opening RFC Connection "
Rest of them working perfectly...
Do I need to do any configuration In Visual Admin?
Could anyone advice
Thanks In Advance
HariKrishnaThanks it got solved it was an error in RFC, I have changed the RFC now it is working fine
Thanks
Hari -
Errors when trying to connect CRM 7.0 to Enterprise Search
Hi!
I encountered 2 errors when trying to connect to a CRM 7.0 system as a backend system from Enterprise Search Cockpit.
The first error is related to ESH_INT_GET_TREX_DESTINATION with a message of ESH_OM_OBJ_MODEL_REP 517:
http://img39.imageshack.us/img39/9722/eserrors1.jpg
The second error is related to "Errors during data cluster import from remote system":
http://img97.imageshack.us/img97/7976/eserrors2.jpg
I don't know if these two errors are related, but any help or suggestions will be greatly appreciated!!
Thank you!
Regards,
Paul4.0 should be fine. My initial thoughts were on the script targetting a framework lesser than 3.5. Am bummed about the error cause in the line
ClientContext clientContext =
new ClientContext(client);
it just creates an instance of the ClientContext class. It should have nothing to do with permissions cause it is not even trying to connect to the sharepoint site. So it looks like it can't find the assembly. Can you place the asembly
under the Microsoft.Net\Framework folder of your machine. SSIS looks for custom assemblies in this folder on design time (Refer
this) Worth a try hey!
http://btsbee.wordpress.com/ -
Oracle Fatal error when trying to connect through sqlplus
Hi,
I am getting the below error when trying to connect to instance through sqlplus
Database version is :10.2.0.3
Operating system= Solaris Operating System (SPARC 64-bit)
OS version=5.10
[lscbd07p2*BMC]-\ORACLE>sqlplus
SQL*Plus: Release 10.1.0.4.0 - Production on Fri Nov 9 07:48:24 2007
Copyright (c) 1982, 2005, Oracle. All rights reserved.
Enter user-name: /as sysdba
ld.so.1: oracle: fatal: relocation error: file /u01/app/oracle/product/db/10.1.0.4/lib/libjox10.so: symbol kststop_: referenced symbol not found
ERROR:
ORA-12547: TNS:lost contact
Enter user-name:
Could you all please give me suggestions in order to solve this problem.
Thanks
MannuHave you recently patched/upgraded? This sounds like there might have been a problem relinking the executables / libraries, and/or a permissions problem. For example you may be referencing a 32 bit library with your 64 bit client.
I believe I recently read a similar case - check Metalink for this symptom.
HTH
Regards Nigel -
There was an error when attempting to connect to the Windows Live Calendar service.
I keep getting a message when I want to check my email you are not connected (but I am,as I can get in my Webbrowser) and the following error message
There was an error when attempting to connect to the Windows Live Calendar service. If the error persists, check to see if there's an upgrade of Windows Live Mail available or contact a service representative.
Can anyone help me, no sense sending me an email, I cannot get into my email.
Lucienne1Hi,
Try installing Windows 2012 Live Essentials here.
You will have to set up your Pop 3 or IMAP email account after installing the updated version per above.
Are you using an Internet Service Provider Email account or a cloud based (IMAP) Email account?
Pop 3 accounts will require incoming and outgoing server addresses and any additional security settings required by your ISP. If you don't have the required settings for Pop 3 you will have to contact your ISP for those.
Jaco
****I am not an HP employee****
Errare humanum est. -
Keep getting sync service error when trying to connect my iphone 5S.
Keep getting sync service error when trying to connect my iphone 5S. It freezes itunes and I can't do anything else. I see that there is an update for my phone and I need to back up, upload new apps, etc before installing. I plug my phone in and get this error every time. I am using a Win 7 SP1
Howdy Susie48825,
It sounds like you are getting an error that mentions the sync services when you connect your phone to your computer and so you cannot sync your device. I would use the troubleshooting from the following article that mentions an error regardign the sync services named:
iTunes for Windows: "Unable to load data class" or "Unable to load provider data" sync services alert
http://support.apple.com/kb/ts2690
Start with these steps:
1. Check that iTunes is up-to-date
Ensure that you have updated to the latest version of iTunes.
2. Reset Sync History
Resetting your Sync History is a simple step which may resolve some syncing issues. If this works, iTunes will prompt to Merge or Replace the information on your device when you next attempt to sync. To reset your Sync History:
Disconnect your device.
Open iTunes.
From the Edit menu, choose Preferences.
Click the Devices tab.
Click the Reset Sync History button, and then reconnect your device.
If this resolves the issue, and you know all of your contacts, calendars, bookmarks and notes are on your computer:
Reset the Sync History again using the steps above.
Select the device in iTunes and click the Info tab.
Scroll down to the Advanced section, and under "Replace information on this iPhone/iPad/iPod touch" select Contacts or Calendars.
Click Apply.
If the issue persists, and you know all your contacts, calendars, bookmarks and notes are on your iPhone, iPad, or iPod touch:
Remove all of the contact and calendar information from Outlook.
Select the device in iTunes and click the Info tab.
Scroll down to the Advanced section, and under "Replace information on this iPhone/iPad/iPod touch" make sure Contacts and Calendars are not selected.
Click Apply.
There are additional steps to use in the article if needed, but these will get you started.
Thank you for using Apple Support Communities.
All the very best,
Sterling -
"error when importing object" when selecting variant
Hello,
we recently migrated from 4.6 to 4.7.
For some programs, when selecting a variant, this gives a runtime error, like
Error when importing object "C131A2"
What is the cause of this? Because the values in the variant aren't valid anymore?
How can this be solved?
Thanks in advance for the helpGlad to help - you'll likely have to run it after every upgrade (for different reports).
Rob -
ORA-12560: TNS:protocol adapter error when trying to connect
hopefully somebody can help me out... the problem i'm having is connecting to the scott/tiger database. i keep getting :
"ORA-12560: TNS:protocol adapter error" when trying to connect to it. it worked previously, but i unistalled oracle 8i personal and reinstalled it. now it doesn't let me connect. what's going on?
thanx,
uriahYou can run the net8 assistant to set up your tnsnames.ora file.
start/programs/oracle/network administration/net8 assistant
When you are done it should look something like this:
ORCL =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS =
(PROTOCOL = TCP)
(Host = )
(Port = 1521)
(CONNECT_DATA = (SID = ORCL))
Bev -
Error when importing object P_lis
Hello Experts ,
I have a task assigned to me where i have to write a program to get all the reports and their variants( variants without space and non obselete variants)
When i am trying to access the variant SDCAS_ADRSEL , I am getting a dump "Error when importing object P_lis ". It has got only one variant JOJO1 in the vari table . Please help me out with this.Hi Aditya,
You might need to provide a few more details on the dump.
I.e.
Exact details of the error that occured.
Where the error occurred
You can grab these out of the dump in ST22. That should help people out, to help understand what you are doing, as it's not really clear from your current description.
Cheers,
Katan -
Error when transporting object data
Hi,
i have installed version 7.1 over verison 7 azdobe livecycle designer, howeven after installation, i try to made some changes, but i got the following error
:" error when transporting object data", anyone familiar with this error?
Please help. Thanks1) It seems that you have deleted a dependent info object from ODS in BW Dev. and so is the warning message that you have deleted that info object.
2) if you have made some changes in an ODS and want to transport those to quality then you should delete all data from that ODS in quality. Delete all tables in ODS.
3) You should activate update rules in development again and transport those with this request.
Error 8 is error caused due to missing objects. do check your request thoughly before you re transport it.
Hope this helps.
Regards, -
Helpme I have error when I try connect from struts to web service
helpme I have error when I try connect from struts to web service using basic authentication . the error message is
[SOAP Exception: fault code= SOAP-ENV Protocol; msg=Unsupported response content type "text/html" must be "text/xml"; ] Response was <html><body> 401 Unauthorized </body></html>
I'm not using ldap for authentication only xml (jazx-data.xml) ... I already create user with jazn.jar for that user , and I dont know why it still error like that ..
Please helpme I don't have anytime more to find the mistake , ??
I'm using Jdeveloper 9i , and oc4j 9.0.4 Server (Not embedded with Jdev)
But when I use with sample java client it success .....
then I try with Struts the response is unsupported response content type text/html must be text/xml response was 401 Unauthorized1.The reason why this error occurs is, we are getting non SOAP response when the program is expecting a SOAP response. Did you set the proxy server correctly? Try to handle the exception and see the content type of the response in your program.
2. While creating the client stub u must check an option for authentication for webservice .should solve ur problem.
thanks
sirisha
Maybe you are looking for
-
Excise Amount not capturing in MIRO
Hi Excise amount is not being captured in MIRO. Case is that a GR has been reversed with 102 and then new GR was made but when user is trying to do Invoice Verification then he is not getting the MODVAT values there. Please suggest what shall we do.
-
I have a master detail form based on two tables. In the DETAIL_BLOCK section I have an item named 'APPROVAL_STATUS' based on the column of the same name in the underlying table. I have an unassociated textbox named CURR_APPROVSTAT in the detail form
-
Salam Alikom i know we can use Master and details in apex but if i have (master - detail - detail ) for 3 tables like Countries table State table Areas table in oracle form it's very easy by wizard , do we have this in apex ? or any way to solve that
-
URGENTLY REQUIRE A CODE FOR FOLLOWING--WOULD BE GREAT HELP
HOW TO VALIDATE XML FILE USING SAX PARSER WITH SCHEMAS like .XSD FILES
-
Question why does firefox (updated) on windows 7 NOT send a hotllink (must copy/paste),when using the 'send link' feature,whereas firefox on XP always sends a hotlink? This feature has always worked perfectly on all my windows XP computers,but not at