Modification Rule(08) allows Full Testing for Quality Batch

Hi Friends
I have case wherein the system allows Full testing in QE51N for material which has been maintained Modification Rule-08 in order
to do reduced testing.
The Modification Rule included in the inspection plan does not work as expected while Processing in QE51N transaction.
Please note that we are Pharma industry.
Thank you

Hello Siddharth,
Please be more elaborative about L08 rule and issue you are facing.
What are the stages created? What is dynamic modification level in Inspection Plan?
May be screenshots will help.
Amol.

Similar Messages

Dynamic modification rule

Hi, what is dynamic modification rue functionality in qm? pls explain with one example how to use the same.

DMR: simple words means when you dynamicall want to change the stages of the inspection.that means you want to reduce the inspection or skip the lots or tighten the inspection.
DMR mainly used for reducing the cost of inspection.
There are many links which are available with example for the same.
Re: DM rule
DMR
Re: Dynamic modification
Dynamic Modification Rule (DMR) at lot creation
DMR - QUALITY LEVEL
Re: DMR @ Char level
DMR inspection stage

Dynamic Modification Rule In Quality Module

Dear All
Please explain me in detail how to use Dynamic Modification Rule (At Lot Level) In quality Module.
Thanks & Regards
Rahul Bhardwaj

Hi,
Dynamic Modification Rule
Definition
The basic data record contains the definition of the inspection stages, the dynamic modification time (at lot creation or after the usage decision has been made), and the conditions for the inspection stage change. Inspection stage changes occur on the basis of the inspection results that are recorded for inspection lots and inspection characteristics (that is, on the basis of their acceptance or rejection).
Use
You can vary the inspection scope using dynamic modification rules. You can store a dynamic modification rule in one of the following places:
In the inspection plan at the header level
In the inspection plan at the characteristic level
In the inspection setup of the material master record at the inspection type level
Structure
A dynamic modification rule contains the definition of the inspection stages, the dynamic modification time, and the conditions that lead to an inspection stage change.
There are always two options that apply to the conditions for an inspection stage change: An acceptance (OK) and rejection (not OK). The system uses these conditions to update the quality level, which always reflects the current status.
The functions for maintaining and displaying dynamic modification rules are primarily contained on three screens:
On the initial screen, you enter the identifier for the dynamic modification rule.
On the header data screen, you maintain a short text and the blocking indicator, and define the time of dynamic modification (at lot creation or when the usage decision is made) and the reset period.
The reset period defines the period of time, which must elapse before the quality level again uses the initial inspection stage specified in the dynamic modification rule as the current inspection stage.
On the inspection stages screen, you edit the inspection stage data (inspection severity, skip, initial inspection stage, and short text). You create the rules for the inspection stage change on this screen.
In QM, the inspection stage describes a test or inspection status that is based on the inspection history and predefined rules. Different inspection stages mean that there are also different inspection scopes and/or inspection severities.
Creating a Dynamic Modification Rule
1.Choose Logistics ® Quality management ® Quality planning ® Basic data ® Sample ® Dynamic modification rule ® Create.
2.Enter the identifier for the dynamic modification rule on the initial screen or choose Copy to use an existing dynamic modification rule as a copy model.
3.Choose Dynamic modification rule to carry out the following activities on the header data screen:
Edit the short text for the dynamic modification rule.
Define the time of dynamic modification (at lot creation or usage decision).
Define the reset period.
Set the blocking indicator if you want to prevent the dynamic modification rule from being used in an inspection plan.
4.Choose Next screen to carry out the following activities on the inspection stages screen:
Define inspection stages.
Define inspection severities for individual inspection stages.
Identify skips.
Identify the initial inspection stage.
Maintain short texts for the inspection stages.
5.Choose Stage change to carry out the following activities on the screen for creating the inspection stage change:
Define the specifications for a stage change for an acceptance (OK)
Define the specifications for a stage change for a rejection (Not OK)
6.Choose Next screen to return to the inspection stages screen and save your entries.
When you save the data, the system prompts you for a confirmation. If you want to include the dynamic modification rule in the allowed relationships for sampling procedures and dynamic modification rules (this is only necessary if a sampling procedure is used in a sampling scheme), you can switch directly to the assignment transaction by confirming this prompt. You define the assignment of sampling procedures and dynamic modification rules in this screen.
If you do not confirm the prompt, the system returns directly to the initial screen and confirms that it has created the dynamic modification rule.
Hope this helps.
Award points if useful.
Regards,
Tejas

Dynamic Modification Rule (At Lot Level) In Quality

Dear All
Please explain me in detail how to use Dynamic Modification Rule (At Lot Level) In quality Module.
Thanks & Regards
Rahul Bhardwaj

Dear,
In material master under (QM view) active "Skip allow" indicator.
Skip lotting in SAP is some what different. SAP does not actual prevent the creation of the inspection lot. It simply sets a status of SKIP on the inspection lot. The lot is still there and if desired, it can be used. Once a characteristic is accessed in the lot, it becomes a normal inspection lot.
You need to setup an auto UD batch job for processing the skip lots and closing them. Skip lots have their own "wait" time defined in plant QM config settings.
That means by DMR you can not stop the inspection lot generation.
Hope clear to you.
Regards,
R.Brahmankar

Quality Management: Check Massage on entering Dynmaic Modification Rule

Hi,
I'm trying to enter 'Dynamic Modification Rule'.(TrCD: QDR1)
I found somthing to work out.
Do anyone have a hint on this?
In the screen of 'Insspection Stages', I entered some data and clicked 'Save', the following massages appeared.
"Either enter an inspection severity or set the skip indicator
Message no. QD505
Diagnosis
For an inspection stage you either assign an inspection severity or set the skip indicator.
You can only assign inspection severities that have been defined as permitted inspection severities in Customizing."
So, I checked this IMG setting;
IMG Menu
> Quality Management > Quality Planning > Basic Data
> Sample, SPC > Define Inspection Severities
But, setting there was the same data I entered on the QDR1.
The 'Inspection Severities' data I set was these;
   1     Inspection without sampling scheme
   2     Reduced inspection
   4     Normal inspection
   6     Tightened inspection
Regards,
Katsumi Makabe

Hi
Please check again following in inspection stage
Example skip at every 5 bacthes
Stage Insp Sev Skip   1st    Short text    Stag Cha    No
10      4               X    Start          X            1
20               X           Skip           X           4
regards
Srinivas

HT1338 What is the best online storage for photos. Specifically one that allows the original image quality to be downloaded should your hard storage goes belly up

What is the best online storage for photos. Specifically one that allows the original image quality to be downloaded should your hard storage goes belly up

I'd put them on an external hard drive(s) and burn them to a DVD as well (at least 2 - 3 copies on different drives/media); I prefer having control and a local solution instead of relying on a server and the possibility of someone (who shouldn't be) downloading my work.

[svn:bz-4.0.0_fixes] 20651: Some MBean tests needed flex.management. jmx stuff in the allow classes list for the class deserialization validator so adding it in on BlazeDS 4 .0.0_fixes.

Revision: 20651
Revision: 20651
Author:   [email protected]
Date:     2011-03-07 12:21:11 -0800 (Mon, 07 Mar 2011)
Log Message:
Some MBean tests needed flex.management.jmx stuff in the allow classes list for the class deserialization validator so adding it in on BlazeDS 4.0.0_fixes.
Modified Paths:
    blazeds/branches/4.0.0_fixes/qa/apps/qa-regress/WEB-INF/flex/services-config.mods.validat ors.xml

Thank you very much!
I cant believe this little comment has been so helpful!
But yes it is:
I explain, despite my efforts to find, googled it, forums, faqs, etc...
no where it mentionned the manifest.fm file is... INSIDE the .jar!
Your comment "a zip" made me attempt to open it with winrar, and I found a manifest.fm file inside!
So far I was editing the one at the "source" of my project and rebuilding it with netbeans.
I am going to try that now.
Actually.... :( no its mentionning my main class!
Manifest-Version: 1.0
Ant-Version: Apache Ant 1.7.0
Created-By: 10.0-b19 (Sun Microsystems Inc.)
Main-class: courseworkjava3d.Simple3D
Class-Path:
X-COMMENT: Main-Class will be added automatically by buildWell I have no problems uploading you the .jar, it is for a coursework it is not a private project or whatever:
http://www.uploading.com/files/CM2LKWYU/BetaCourseworkJava3d_Final.jar.html
Oh and I felt on your comment "dont ask us" as if I was suppose to know... i'm a beginner, I did not know that! And I tried to give you so many infos so you dont lose your time if you want to help, especially as after my own research I found many, many results for this "main class" and I tried a few solutions!
Edited by: CupofTea on Apr 13, 2008 3:28 AM

[svn:bz-trunk] 20650: Some MBean tests needed flex.management. jmx stuff in the allow classes list for the class deserialization validator so adding it in on BlazeDS trunk .

Revision: 20650
Revision: 20650
Author:   [email protected]
Date:     2011-03-07 12:20:03 -0800 (Mon, 07 Mar 2011)
Log Message:
Some MBean tests needed flex.management.jmx stuff in the allow classes list for the class deserialization validator so adding it in on BlazeDS trunk.
Modified Paths:
    blazeds/trunk/qa/apps/qa-regress/WEB-INF/flex/services-config.mods.validators.xml

Thank you very much!
I cant believe this little comment has been so helpful!
But yes it is:
I explain, despite my efforts to find, googled it, forums, faqs, etc...
no where it mentionned the manifest.fm file is... INSIDE the .jar!
Your comment "a zip" made me attempt to open it with winrar, and I found a manifest.fm file inside!
So far I was editing the one at the "source" of my project and rebuilding it with netbeans.
I am going to try that now.
Actually.... :( no its mentionning my main class!
Manifest-Version: 1.0
Ant-Version: Apache Ant 1.7.0
Created-By: 10.0-b19 (Sun Microsystems Inc.)
Main-class: courseworkjava3d.Simple3D
Class-Path:
X-COMMENT: Main-Class will be added automatically by buildWell I have no problems uploading you the .jar, it is for a coursework it is not a private project or whatever:
http://www.uploading.com/files/CM2LKWYU/BetaCourseworkJava3d_Final.jar.html
Oh and I felt on your comment "dont ask us" as if I was suppose to know... i'm a beginner, I did not know that! And I tried to give you so many infos so you dont lose your time if you want to help, especially as after my own research I found many, many results for this "main class" and I tried a few solutions!
Edited by: CupofTea on Apr 13, 2008 3:28 AM

How I can allow always and for all sites full-screen mode?

How I can allow always and for all sites full-screen mode?
And I want choose anywhere option "never show notification about full-screen mode" (screenshot attached)
RUS
Как я могу всегда разрешить и для всех сайтов полноэкранный режим?
И я хочу выбрать где-нибудь опцию "никогда не показывать уведомление о полноэкранном режиме" (скриншот приложен)

There is a preference setting on the <b>about:config</b> page that is meant for developers and testers to make this possible, but it is not meant for normal users.
*full-screen-api.approval-required = false
You can open the <b>about:config</b> page via the location/address bar.
You can accept the warning and click "I'll be careful" to continue.
*http://kb.mozillazine.org/about:config

How to Implement Dynamic Modification Rule for Material & multiple vendor Combination

Hi Team,
In dynamic modification rule for Material & vendor combination, i have maintained material & vendor in Inspection plan at Material Assignments
1.If i purchase same material from different vendors then how to implement ?

Hi Balaji,
I am not sure if i have followed your requirement.
What do you want to do with Vendor Z? Do you want to inspect each lot from Z?
If yes:
Then Create 2 Inspection plans with same Operations and Same MICs, In Material Assignment, mention Vendor as Z so that 1st inspection plan will only be for Vendor Z. Do not enter DMR in Header.
In 2nd inspection plan Enter DMR and do not mention any vendor so this plan will be applicable for all vendors except Z.
If No:
Then create Qm info record for vendor Z with "No inspection" set in QI06.
Amol.

Output for Quality test certificate

Hi mates
Can anybody help me out in Configuring Output type for Quality test certificate while creating Outbound delivery.
Thanx
regards..,
Karthik

Hi..
Go to QA11 or QA31..
system will ask for Inspection lot.. do the user status(UD completion) wid ststus "A"
and save..
go back and check tab Message type..
hope this will help u...
correct me if i m wrong...
thanks..
mk

Goods send for quality testing

hi,
sap gurus,
good morning to all,
what type of business process can v identify as the goods will send for LAB TESTING/QUALITY
TESTING and they are excised.
can anybody send the steps for the following.
regards,
balaji.t
09990019711

Hi Balaji
there are two kinds stock 1) internal manifacture 2) extranal stock comming from vendor.
1) if it si internal finished goods it willlbe send it for quality testing after every thing is fine then it will go to un-restricted stock with momennt type 561
2) if it external stock it is comming from vendor.with ref to po MM people they do MIRO and MIGO (invoice verification) then it will go to unresticted stock. otherwise it will send it back to vendor.

FULL Test hardware scan FAILED.

FULL Test hardware scan FAILED. Does anyone know what this means? Failed Error code WPE01-ZLKAnd how to fix it? STUCK in Chiang Mai, Thailand. I WANT someone who speaks English IF there is a repair place. BIG problem? small problem? I don't know. Thanks.

Good day.
Could you provide a bit more information about your system?
Model, OS version, any hardware modifications, might prove helpful to members providing advice.
Regards.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee.

QM:Maximum skip duration in dynamic modification rule

Hi
Can anybody explain how the system behaves with
QM:Maximum skip duration in dynamic modification rule.
Gobinathan G

Hi,
In dynamic modification rule you maintain the inspection modification based on the quality level. You mention the maximum skip duration for resting the skip status if the inspection lot is not created during the specified period after creation of last inspection lot. That means the Skip status will be reset to Inspection status if the lot is not created during the specified period & you will have to inspection the lot instead of skipping. If the lot is generated within the period, then you will be able to skip the inspection.
Regards,
Prashant

RV016 Router Allow All Traffic For Outside IP

Hi,
I need to configure the firewall to allow all traffice for an IP address of a sever. What steps in the router do i need to configure this? This is a cloud based voip server and we have IP phones and we need to add an IP address of the phone server to allow all traffic for that IP.
thanks.

Hi Jonathan,
I have a similar problem with VOIP traffic being dropped by my new RV016 v3 router.
I have created one Firewall Rule, to allow ALL traffic from the external VOIP PBX provider (single IP) to connect to the internal VOIP phones, which have assigned addresses in a small IP Address range (eg. 10.1.2.50 - 10.1.2.59)
The Aastra VOIP phones continually loose their registration wtih the cloud-based PBX. If you make an outgoing call, it will work, but the PBX will lose connection with the phone, 3 or 4 minutes after you hang up, and will mark it as offline. Incoming calls made within the 3 or 4 minutes will get through, but after that they go right to voicemail on the PBX system.
We used to have an RV016 v2 router and VOIP traffic worked OK, with a similar Firewall Rule. We replaced the v2 router because its CPU crashed.
I tested the VOIP traffic with a WRT160 router with minimal Firewall Rules, and it works OK, as long as SIP-ALG is turned Off. We want to use the RV016 because it provides a larger number of ports for our LAN.
Any suggestions ?
Kirk

Modification Rule(08) allows Full Testing for Quality Batch

Similar Messages

Maybe you are looking for