Modulation Toolkit not found in Speedy-33

HI,
I am facing a very basic problem in using LabVIEW's modulation and advance toolkits in Speedy 33. When I open Speedy 33 environment, I am unable to find modulation toolkit on it although this toolkit is available in normal LabVIEW environment. What can be the problem and how to use these toolkits in Speedy 33 environment. Or do we have modulation toolkit available in Speedy-33?
Thanks
Regards

I would take a look at the PXIe-5641R RIO IF Transciever. This sounds like it would fit what you're trying to do. Otherwise, depending on what frequency you're looking to generate/receive, you could look into some of our RF hardware or you could simply use the Modulation toolkit and use one of our arbitrary waveform generators and one of our high speed digitizers.
Chris

Similar Messages

Function module "GM_DOCUMENT_REVERSE" not found. after Patch Update

Hi Abapers/Basis
After patch update i am not able to do FBCJ reversal entry getting below error message.
Runtime Errors         CALL_FUNCTION_NOT_FOUND
Exception              CX_SY_DYN_CALL_ILLEGAL_FUNC
Date and Time          25.05.2011 14:43:26
Short text
     Function module "GM_DOCUMENT_REVERSE" not found.
What happened?
     The function module "GM_DOCUMENT_REVERSE" is called,
     but cannot be found in the library.
     Error in the ABAP Application Program
     The current ABAP program "SAPLRWCL" had to be terminated because it has
     come across a statement that unfortunately cannot be executed.
What can you do?
     Note down which actions and inputs caused the error.
     To process the problem further, contact you SAP system
     administrator.
     Using Transaction ST22 for ABAP Dump Analysis, you can look
     at and manage termination messages, and you can also
Error analysis
    An exception occurred that is explained in detail below.
    The exception, which is assigned to class 'CX_SY_DYN_CALL_ILLEGAL_FUNC', was
     not caught in
    procedure "CALL_DISPATCHER_STORNO_R" "(FORM)", nor was it propagated by a
     RAISING clause.
    Since the caller of the procedure could not have anticipated that the
    exception would occur, the current program is terminated.
    The reason for the exception is:
    The program "SAPLRWCL" contains the CALL FUNCTION statement.
    The name of the function module to be called is "GM_DOCUMENT_REVERSE".
    No function module exists with the name "GM_DOCUMENT_REVERSE".
    All function modules are listed in the Function Library (SE37).
    Possible reasons:
    a) Wrong name specified. Pay particular attention to
       upper/lower case and underscores ("_").
       or
    b) Transport error
    c) In the case of an enqueue/dequeue module,
       the lock object may not have been activated
       (ABAP/4 Dictionary).
How to correct the error
    Check the last transports to the SAP System.
    Is the program "SAPLRWCL" currently being changed?
    If an enqueue/dequeue module is involved, is the activation
    of the lock object missing in the ABAP/4 Dictionary?
    If the error occures in a non-modified SAP program, you may be able to
    find an interim solution in an SAP Note.
    If you have access to SAP Notes, carry out a search with the following
    keywords:
    "CALL_FUNCTION_NOT_FOUND" "CX_SY_DYN_CALL_ILLEGAL_FUNC"
    "SAPLRWCL" or "LRWCLF10"
    "CALL_DISPATCHER_STORNO_R"
    Function modules with names similar to "GM_DOCUMENT_REVERSE":
    GM_DOCUMENT_CLOSE
    GM_DOCUMENT_RECORD
    GM_DOCUMENT_DELETE
    GM_DOCUMENT_POST
    GM_DOCUMENT_CHECK
    G_DOCUMENT_RECORD
    GJ_DOCUMENT_RECORD
    GM_DOCUMENT_PROJECT
    GET_DOCUMENTS
    GM_DOCUMENT_DISPLAY
    If you cannot solve the problem yourself and want to send an error
    notification to SAP, include the following information:
If you cannot solve the problem yourself and want to send an error
notification to SAP, include the following information:
1. The description of the current problem (short dump)
   To save the description, choose "System->List->Save->Local File
(Unconverted)".
2. Corresponding system log
   Display the system log by calling transaction SM21.
   Restrict the time interval to 10 minutes before and five minutes
after the short dump. Then choose "System->List->Save->Local File
(Unconverted)".
3. If the problem occurs in a problem of your own or a modified SAP
program: The source code of the program
   In the editor, choose "Utilities->More
Utilities->Upload/Download->Download".
Moderator message: please don't just dump your dumps, search for SAP notes or open a call with SAP instead.
Edited by: Thomas Zloch on May 25, 2011 2:16 PM

Hi Karthik,
Thank you for ur reply.
I did not implement any user exit/ badi. Dump is saying that my smarform function module does not exist in the se37 library.
I have excuted my form through se38, that time is working fine. When i tried through output type it is going to dump.
Regards,
Kusuma.

Warning: /lib/modules/3.14.17-1-lts/modules.devname not found

I am trying to use linux-lts but get this error, I'm using rEFInd. I am able to boot the standard arch kernel, but when selecting the other entry in refind I just get the error.
Warning: /lib/modules/3.14.17-1-lts/modules.devname not found - ignoring
The file does exist though.

I sorted it, though not exactly as I want it. I had to change the initrd line in /boot/refind_linux.conf to be initramfs-linux-lts.img, I had previously copied the boot line and created a new one with that initrd line, but that didn't work. As I have things now I can only boot the lts kernel, if I want to change to the other I need to manually change that line before rebooting.

Error: "FATAL: Module oracleasm not found" in Red Hat 6

Hi all:
   OS.....: Red Hat 6.5 (64 bits)
   I am preparing to install an 12c RAC in a Red Hat 6.5. While configuring the ASMLib, i got the following error while executing "/usr/sbin/oracleasm init":
      May 2 18:23:20 oraprd01 modprobe: FATAL: Module oracleasm not found.
   I configure the Oracle YUM Repository and installed the "kmod-oracleasm" package. And in the link (Oracle ASMLib Downloads for Red Hat Enterprise Linux Server 6) i got the "oracleasmlib" and "oracleasm-support" packages, as you can see below:
      [root@oraprd01 binarios]# rpm -qa | grep -i oracleasm
      kmod-oracleasm-2.0.8-4.el6_6.x86_64
      oracleasm-support-2.1.8-1.el6.x86_64
      oracleasmlib-2.0.4-1.el6.x86_64
   My kernel is:
      Linux oraprd01 2.6.32-431.el6.x86_64 #1 SMP Sun Nov 10 22:19:54 EST 2013 x86_64 x86_64 x86_64 GNU/Linux
   My Red Hat version is:
      [root@oraprd01 binarios]# cat /etc/redhat-release
      Red Hat Enterprise Linux Server release 6.5 (Santiago)
   Why am i getting the above error while trying to init the oracleasm module? What am i doing wrong?
   Thanks in advance.

Problem solved.
   I installed an older version of the kmod-oracleasm (kmod-oracleasm-2.0.6.rh1-3.el6_5.x86_64) downloaded from Red-Hat Customer Portal. Now the ASM module is loaded.

Pls help in WEBDYNPRO Function Module 'RFC_START_PROGRAM' not found error

Dear Friends,
While i am calling one function module in webdynpro the follwing erroe is coming.
Error:-
Function Module 'RFC_START_PROGRAM' not found error
Code:-
CALL FUNCTION 'ZUPDATE' DESTINATION 'PCNCLNT300'
    EXPORTING
      im_material = item_matnr
      im_vornr    = item_vornr
      im_sheet    = item_sheet
IMPORTING
      value = ZMESSAGE .

Hi,
try declarig variable of type rfc_dest
data: lv_dest type rfc_dest.
call....
destination lv_dest
offcourse make sure your rfc destination has that name in sm59
and you have the corect authorizations to your user in the remote system
Are you btw sure that there is no screen action called inside
the function module? popup or something? because you cannot
call functions that have screen interaction like in sapgui
grtz,
Koen

Error 'Function module "IAOM_ACCOUNT_MANAGER" not found' in RPM_FIN02.

Hi,
When I am trying to run report RPM_FIN02 in ERP system, I am getting error ''Function module "IAOM_ACCOUNT_MANAGER" not found'.
Please note i have done required configration in both systems i.e. cProject and ERP.
Can somebody help me on this?
Regards,
Manoj

Thanks for your input.
This note is already implemented in our system.
Anyway my problem is solved.The problem was in our configration.
Regards,
Manoj

Function module "OCS_ALV_UI_QTRACE_AVAILABILITY" not found.

Hi,Guy ,
When we use the spam ,the system raise an Abap dump ,the message is :
Function module "OCS_ALV_UI_QTRACE_AVAILABILITY" not found.
My System is ECC6.0
can anybody tell me how to solve it ?thanks in advance .
Jialiang.Qiu

Hi all, I've same problem,
do you know the solution?

Modules.devname not found after Kernelupdate

Hello everyone,
my system broke after the latest kernel update, now i get the following when booting:
Warning: /lib/modules/3.14.0-4-ARCH/modules.devname not found - ignoring
ERROR: device '[UID]' not found Skipping fsck
And im dropped in a recovery shell, where I cannot even type. I will prepare a live CD, but don't know yet what to do, as i did not found much on google or in the forums, so I would be happy for any help.

falconindy wrote:That doesn't make sense. If you deleted the preset, how can you tell mkinitcpio to use the preset?
I meant delete it, reinstall mkinitcpio and kernel and run the command.
Last edited by ollie (2014-04-15 13:29:38)

Module vbox* not found; Virtualbox; additions [RESOLVED]

I'm running arch in virtualbox.
And first, I installed virtualbox-archlinux-additions from repository by pacman and everything worked fine, except a little problem.
So I thought (altough it's not recommended) installing virtualbox guest additions from virtualbox (host).
ERROR:
WARNING: Module vboxguest not found.
WARNING: Module vboxsf not found.
WARNING: Module vboxvideo not found.
I tried pacman -S {linux linux-lts and xorg-*; mesa and virtualbox-archlinux-additions}, then modprobe vboxsf vboxguest vboxvideo, still the Not Found error.
Last edited by lqs (2012-07-27 08:03:18)

It's 1 pm in China
Thanks!Your way works.
ewaller wrote:
It is getting late here, so maybe it is just me... but I cannot figure out what you are trying to do.
Is the Archlinux you are working with in a virtual machine? If so, you want to install virtualbox-archlinux-modules.

[SOLVED] FATAL: module nvidia not found

Hi
I have been working on setting arch up on my laptop the past couple of days. It's a Thinkpad T61 with an NVIDIA Quadro NVS 140M gpu.
I started with the nouveau driver and all was working fine, but I decided to switch to the propriatery driver to see if it had any better power saving features.
Well, I installed 'nvidia-utils 275.09.07' with pacman > ran 'nvidia-xconf' > reboot. All I got was a few GDM failed to start error messages.
So I start digging around the xorg log and what not, tried simply running startx. Turns out the 'nvidia' module is nowhere to be found.
If I 'modprobe nvidia'
FATAL: Module nvidia not found.
So I tinker with it a bit more with no results. Reinstalled a few times, even tried installing the latest beta driver from AUR. Then I just said to hell with it and did a fresh arch install.
Now I'm on a clean install. All I have done is sync and update with pacman, create a use and install X and the nvidia driver.
Run 'startx'. Same thing as before.
Where is that nvidia module supposed to be?
In /lib/modules/2.6.39-ARCH/modules.dep there is this line. I grepped 'nvidia' from it.
kernel/drivers/video/nvidia/nvidiafb.ko.gz: kernel/drivers/video/fb_ddc.ko.gz kernel/drivers/i2c/algos/i2c-algo-bit.ko.gz kernel/drivers/video/vgastate.ko.gz kernel/drivers/i2c/i2c-core.ko.gz
And that nvidiafb file is there. Don't know if that is the right one.
Am I doing something horribly wrong here or is this a bug? I'm really not sure at this point.
Has anyone else been unlucky enough to have to deal with this issue?
Last edited by raginaot (2011-07-17 16:49:29)

raginaot wrote:
mikesd wrote:
Did you install nvidia as well as nvidia-utils?
The wiki has a great nvidia page.
ehm... I did not...
I must be getting dyslexic or something cause I don't know how many times I read that wiki page trying to find something I had missed..
Anyway, installed the nvidia package and it's all good now. Thanks.
I'm gonna go sit in the corner now.
You're a big enough man to actually admit you've erred. In my books that makes you a very respectable man so no more corner-sitting for you.

Nvidia-304xx Module nvidia not found

Hi,
I had a nvidia GTX 260 as primary gpu with the latest nvidia running.
Now I switched to an old GT 6600. Therefore I installed nvidia-304xx but modprobe nvidia fails.
[pheinrich@ARCH ~]$ sudo modprobe nvidia
modprobe: FATAL: Module nvidia not found.
[pheinrich@ARCH ~]$ pacman -Qs nvidia
local/lib32-libcl 1.1-1
OpenCL library and ICD loader from NVIDIA (32-bit)
local/lib32-libvdpau 0.7-2
Nvidia VDPAU library
local/lib32-nvidia-304xx-libgl 304.121-2
NVIDIA drivers libraries symlinks (32-bit)
local/lib32-nvidia-304xx-utils 304.121-2
NVIDIA drivers utilities (32-bit)
local/lib32-opencl-nvidia-304xx 304.121-2
OpenCL implemention for NVIDIA (32-bit)
local/libcl 1.1-3
OpenCL library and ICD loader from NVIDIA
local/libvdpau 0.7-1
Nvidia VDPAU library
local/nvidia-304xx 304.121-5
NVIDIA drivers for linux, 304xx legacy branch
local/nvidia-304xx-libgl 304.121-2
NVIDIA drivers libraries symlinks, 304xx legacy branch
local/nvidia-304xx-utils 304.121-2
NVIDIA drivers utilities and libraries, 304xx legacy branch
local/opencl-nvidia-304xx 304.121-2
OpenCL implemention for NVIDIA, 304xx legacy branch
I do not know what I have done wrong.

I found it on
https://wiki.archlinux.org/index.php/NVIDIA
For GeForce 6000/7000 series cards [NV40-NV4E, NV63-NV68], install the nvidia-304xx or nvidia-304xx-lts packages, available in the official repositories.
When I select the dropdowns on the nvidia website I get the 304.88 for that card so I think nvidia-304xx would be the right one.
I think there was something wrong during installation. If the nvidia-304xx wouldn't be compatible the nvidia module must be installed regardless.
I will try nvidia.
Edit 1
Something completly wrong here. I have installed the package nvidia now again.
[pheinrich@ARCH ~]$ sudo pacman -Qs nvidia
local/lib32-libcl 1.1-1
OpenCL library and ICD loader from NVIDIA (32-bit)
local/lib32-libvdpau 0.7-2
Nvidia VDPAU library
local/lib32-nvidia-libgl 337.25-1
NVIDIA drivers libraries symlinks (32-bit)
local/lib32-nvidia-utils 337.25-1
NVIDIA drivers utilities (32-bit)
local/lib32-opencl-nvidia 337.25-1
OpenCL implemention for NVIDIA (32-bit)
local/libcl 1.1-3
OpenCL library and ICD loader from NVIDIA
local/libvdpau 0.7-1
Nvidia VDPAU library
local/nvidia 337.25-3
NVIDIA drivers for linux
local/nvidia-libgl 337.25-2
NVIDIA drivers libraries symlinks
local/nvidia-utils 337.25-2
NVIDIA drivers utilities
local/opencl-nvidia 337.25-2
OpenCL implemention for NVIDIA
But "modprobe nvidia" prints
[pheinrich@ARCH ~]$ sudo modprobe nvidia
modprobe: FATAL: Module nvidia not found.
Maybe it has to do with the situation that I had installed "nvidia" before then removed it an installed nvidia-304xx ?
Last edited by _pheinrich_ (2014-06-29 13:45:52)

[SOLVED] Fatal: module phc_intel not found

I've used the phc_intel package from AUR, yet it didn't work for me and I removed it. Now, during boot I get the "Fatal: module phc_intel not found" message. It doesn't stop the boot but it's annoying. There is no mention of it in rc.conf:
MOD_AUTOLOAD="no"
#MOD_BLACKLIST=() #deprecated
MODULES=(!usblp acpi_cpufreq cpufreq_ondemand iwl4965 ac battery button processor thermal video btusb cdrom agpgart intel-agp nvram i2c-i801 i2c-core evdev joydev pcspkr psmouse serio_raw led-class mmc_core ricoh_mmc sdhci-pci sdhci pci_hotplug shpchp thinkpad_acpi wmi rtc-cmos rtc-core rtc-lib nvidia output iTCO_vendor_support iTCO_wdt snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-codec snd-hda-intel soundcore scsi_mod ahci ata_piix e1000e bluetooth mac80211 rfkill iwlagn iwlcore cfg80211 pcmcia_core rsrc_nonstatic yenta_socket usb-storage usbcore ehci-hcd uhci-hcd ieee1394 ohci1394 sd_mod sr_mod st)
Any ideas?
Last edited by dcc24 (2009-12-19 19:59:45)

Yes, there was a conf file there. Removing it solved the problem. Thanks!

[SOLVED] Module efivars not found but /sys/firmware/efi/efivars avail.

Hi all,
I'm installing Arch Linux on a new laptop (Dell Precision M6800) but cannot get UEFI to work.
Outside arch-chroot, when I type "modprobe efivars" I get the "Module efivars not found". Which indicates that I didn't boot using UEFI.
But, I booted using it (in my bios I selected my USB drive under the UEFI section and not the BIOS one), and more importantly, I have a fully populated /sys/firmware/efi/efivars folder with non empty files in it. So as I read on some forum, this means I booted using UEFI. So why can't I load the efivars module then? What am I missing? What can I do to debug more?
I have used the 201311 dual iso image and just dd'ed it on my USB drive, I did not follow the instructions from https://wiki.archlinux.org/index.php/UE … B_from_ISO because I read them afterwards, but this will be my next step if you tell me this is the reason why UEFI does not work (although I have recently installed an UEFI Arch Linux on a UX31A without doing it so I guess these instructions are outdated).
Thanks for your help,
Olivier
Last edited by jolivier (2013-11-14 10:09:48)

jolivier wrote:
Hi all,
I'm installing Arch Linux on a new laptop (Dell Precision M6800) but cannot get UEFI to work.
Outside arch-chroot, when I type "modprobe efivars" I get the "Module efivars not found". Which indicates that I didn't boot using UEFI.
But, I booted using it (in my bios I selected my USB drive under the UEFI section and not the BIOS one), and more importantly, I have a fully populated /sys/firmware/efi/efivars folder with non empty files in it. So as I read on some forum, this means I booted using UEFI. So why can't I load the efivars module then? What am I missing? What can I do to debug more?
Read the whole section: https://wiki.archlinux.org/index.php/Un … _Variables
Last edited by the.ridikulus.rat (2013-11-13 18:48:21)

Function module "CRM_DOWNLOAD_RCV_EXIT" not found error

Hello experts,
We are using SRM 5.0 connected to an ECC 6.0 backend system
In SRM, trans. SMQ2 I see queues with status SYSFAIL, and inside them I find that supposely the error is "Error in Mapping (Details: transaction SMW01)".
When I re-process it, I get the following dump in ST22: "Function module "CRM_DOWNLOAD_RCV_EXIT" not found". This module does not exist in SRM, and my guess is that CRM is sending stuff to SRM.
I have everything configured correctly, exactly as note # 720819.
I'll appreciate your comments on this.
Regards,
Gilberto Gallardo

Hi
CRS_DOWNLOAD_RCV_EXIT -check this fm you defined in CRMSUBTAB table in r/3
CRMSUBTAB for subscription table for Up and Download Object and add the following values:
User ObjectName U/D Obj. Class Function Obj. Type Funct. Name
CRM empty Download Material empty empty CRS_MATERIAL_EXTRACT
CRM empty Download Material empty empty CRS_CUSTOMIZING_EXTRACT
CRM empty Download Material empty empty CRS_SERVICE_EXTRACT
BR
Muthu
Edited by: Muthuraman Govindasamy on Oct 24, 2008 6:22 AM

Function module "RSA_RSBASIDOC_READ" not found.

I am trying to connect a BW (7.00) system to a R/3 source system (46c) but get the short dump :
Function module "RSA_RSBASIDOC_READ" not found.
I can see on the R/3 side of things that this FM does not exist.
Does anyone know if there is there a note I can implement or patch level I have to upgrade to?
cheers

Hi,
I am not sure at which support pack or patch level this one got created in the system. But as you are using the older version, and directly you can not upload or apply the patch which is required and which actually valid for higher releases, as I guess.
So it is suggested to raise an OSS message to the SAP. They will guide you properly. Or else by referring to the function module which is available in the latest systems, you can create some Z function module and use it accordingly.
Regards,
Santhosh.

Modulation Toolkit not found in Speedy-33

Similar Messages

Maybe you are looking for