Monitor and record server performance

Hi all.
This is not really Arch related but a general question. I have a web server that has services crashing. I think it may be due to low mem. Is there any software or some method that would allow me to monitor/log server stats/performance and then see a graph over time.
My hope is to be able to see if services fail due to mem outages, or some other reason. I would also like to know better what my peak times are.
Any suggestions are greatly welcome.
Thanks alls for your input
Cheers,
P.

What is the best way to uninstall and reinstall the Focusrite MIDI interface driver. And to uninstall and reinstall the Subtlesoft Midipipe (which is required to get the correct mapping for a Yamaha drumkit)? This was done for me at the Apple Store One On One session in a prior attempt to fix this problem but obviously it did not work. I'd like to try it one more time with the drumkit connected. I did see a screen at one point which allowed me to select the inputs from the Focusrite but I could never find it again. I don't think it was a Garageband menu but somewhere else, maybe during the driver or software install for the Focusrite. I would love to get back to that screen again and take a hard look at it.

Similar Messages

  • CUCCX 8.0 - Call monitoring and recording

    Hello,
         I've worked with desktop-side monitoring and recording on various versions fo CUCCX in the past and have come to the point where this particular solution is not practicle anymore (we would need cordinate with the desktop group to install Cisco-approved NICs, and yes I am aware that there is a workaround but it doesn't work on NICs that do not support promiscuous mode.)
         CUCCX supports a server-side method as well, but I have no experience in it and would like to find a how-to document.  Would it work in a mixed network environment?  Any pointers would be helpful.

    Hi
    In my experience the 'lack of support for promiscuous mode' NICs is vastly overstated. I've not come accross a single NIC that doesn't work. I suspect that document was written back when NICs were based on valves or something.
    Typically the main issues are simple config errors - not doing span-to-pc-port, not daisy chaining PCs, etc.(And on v8.0+ it's usually due to the services falling over, which will ruin things for you whether you use CAD or server-side monitoring!)
    RE: server side monitoring - I've worked on some fairly large SPAN based deployments. UCCX is pretty agnostic, you just need to make sure it sees each conversation (and sees each one only once!) using whatever SPAN config you can. It's more a question of how handy you are with networking than anything specific to UCCX.
    Regards
    Aaron

  • Monitor weblogic cluster server performance

    I am using "System Monitor" got from http://dev2dev.bea.com/utilitiestools/monitoring.html to monitor my weblogic server performance. For single server, it is working well.
    However I can't use it to monitor the cluster server performance. For example:
    server 1 and server 2 have clustered weblogic server - APPS listerning on port 8888. On server 1, I have admin server running on server 1 - ADMIN_SVR1 listerning on port 232.
    I can dump the admin server Mbean information as:
    $java com.iternum.jmx.monitor.SystemMonitor -url t3://localhost:232 -user admin -password xxxxx -mBeanType ExecuteQueueRuntime -of performance.txt
    However I can't dump the cluster server performance data as following:
    $java com.iternum.jmx.monitor.SystemMonitor -url t3://localhost:8888 -user admin -password xxxxxx -mBeanType ExecuteQueueRuntime -of performance.txt
    Did I make any mistake? Do you have better tool to monitor weblogic performance?
    Thanks in advance,
    carl

    how to attach GC file?

  • Monitoring and recording feature not working in UCCX

    Hi,
    The recording and monitoring option is not working in the new UCCX setup I have installed.I have configured following things for desktop monitoring as per the document
    1)Checked that IP Phones are diasy chained and speakers of Supervisor's PC is working,NIC card of agent's and supervisor desktops are compatible
    2)In web CDA P phones to be monitored have been configured
    3)In CCM configured the phone for "Span to PC port" as enabled also configured "Advertise G.722 codec" as disabled
    4)Ran postinstall.exe on agents system and checked if correct NIC adapter is being used for monitoring
    5)Checked the NIC binding order in UCCX server and that is correct
    I noticed one thing that "services"  in both CAD and CSD are showing as "partial services" and they are monitoring and recording services only.Hence is this problem related to these services? How do i correct the recording and monitoring issue?
    Regards
    Amit

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin-top:0in;
    mso-para-margin-right:0in;
    mso-para-margin-bottom:10.0pt;
    mso-para-margin-left:0in;
    line-height:115%;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;}
    I would first recycle the VOIP Monitoring Service on both node if this is HA.  This will not affect calls or call processing.
    In addition, you stated you ran post install on the clients desktop but have you ran post install on the server itself?
    In the desktop Administrator, what server is selected to be the default VOIP Monitor server?
    Jason M. Hutchinson

  • How to fix problem "PYLR2000 error playing a file. Try again or contact your Monitoring and Recording administrator"

    Hi,
    I'm using qm 8.5.2 (endpoint recording) most of customer PCs cannot play recording file in application.
    When I launch application and try to play recoding file, it is stuck and show error message "PYLR2000 error playing a file. Try again or contact your Monitoring and Recording administrator." I've install all cilent requirements (validate pc is pass). The error still occur. Even though all requirements are complete .
    So, How to fix this problem.
    Thank in advance
    Namkhao

    Hi bsetexast,
    I'm fix this problem by using Java(TM) version 6.0.200.2 that can be download from UCCX when first run CSD (supervisor desktop). Even other higher java version is valid but this problem still occur. If you install higher version, you should uninstall it first and install this version as well.
    If you cannot find them, I will send you via email.

  • How do I monitor and record a MIDI instrument on Garageband?

    I may be missing something simple in Garageband setup. I want to monitor and record a drumkit via its MIDI output. It is a Yamaha DTXplorer so I have Subtlesoft Midipipe installed and a Focusrite Saffire 6 USB converter. Microphones and guitars are being monitored and recorded with without problem. When I connect the Focusrite to my Macbook air and drumkit the MIDI indicators are blank, no MIDI input detected by Garageband. Then I close GB and launch Midipipe, the MIDI input detected light on the Focusrite illuminates and GB detects one MIDI input (Saffire 6) in preferences window. But if I select new track/software instrument Saffire 6 input is grayed out and so cannot be selected (if I select the mic or guitar sources it is bold and can be selected). If I go ahead and create the software instrument there is no monitor button and nothing is heard or recorded.

    What is the best way to uninstall and reinstall the Focusrite MIDI interface driver. And to uninstall and reinstall the Subtlesoft Midipipe (which is required to get the correct mapping for a Yamaha drumkit)? This was done for me at the Apple Store One On One session in a prior attempt to fix this problem but obviously it did not work. I'd like to try it one more time with the drumkit connected. I did see a screen at one point which allowed me to select the inputs from the Focusrite but I could never find it again. I don't think it was a Garageband menu but somewhere else, maybe during the driver or software install for the Focusrite. I would love to get back to that screen again and take a hard look at it.

  • Live Monitoring and Recording for VPN Remote CAD Agents in UCCX

    Dear all,
    We have deployed UCCX 5.0(2) for one of our customers.
    Silent Monitoring and Recording are working fine for local agents.
    We have deployed new Remote agents using IP Communicator and Cisco VPN on their PC. Everything is working fine but could not monitor or record them.
    We have made site-to-site VPN using a PIX and give these agents Hard Phones 7942. Everything is working fine but could not monitor or record them.
    We also installed WFO QM client on their PCs in order to record calls but no way !
    Is there any way that we can use in order to make these agents silently monitored and recorded?
    Thanks for all.

    good afternoon,
    I am not a senior guy but we experienced the same issues with monitoring users at home on VPN. After some trouble shooting I found that most users are on wireless and when I had them plug in with a cable we could hear their calls and record fine with no issues. Though, the agents preferred to be on wireless, of course! the senior engineer did mention something about changing the Codec and utilizing some DSP resources.
    MM

  • Monitoring and recording IPCommunicator

    hi, what do i need to enable to monitor and record an agent that uses an IP Communicator? thanks!

    Hi,
    Here is the doc to configure Desktop monitoring and recording:
    In CIPC while running postinstall select the NIC adaptor of the PC:
    http://www.cisco.com/en/US/customer/products/sw/custcosw/ps1846/products_tech_note09186a008075025a.shtml
    HTH

  • Monitoring and recording using my audio interface

    I am new to the logic express program. When I try to record with my audio interface (whether mic or instrument), do I always have to go to the "Device Input" settings and swithc the input to my interface? Even when I do that, the bars move indicating sound, but I cant hear it...dont know what I am doing wrong?
    So basically, right now, I record without being able to monitor, then when I want to hear it, I have to switch the device input back from the interface to the default device?
    It seems I am making this harder than it is.
    Thanks for the help.

    I am having the same problem (using a presonus firepod). Tried the aggregate solution but it is not working.
    Steps I took: Aggregate Device Editor > selected firepod and built-in output. Then in Audio Midi setup selected aggregate device as default input. In Logic Ex 8, preferences>audio>enabled core audio and selected aggregate device as the driver. Created a new track, tried using input monitoring and the record button. I can see the levels go up and down, so there is signal, but no sound for me to hear. The inputs and outputs for the track are input 1 outputs 1&2.
    So am I doing something wrong?
    Thanks guys.

  • Monitoring and recording problem with midi vs audio firewire

    I'm trying to record my Roland synth via Inspire firewire box into Logic express. I'm able to record and monitor thru the output of the inspire box. However If I'm using firewire, I can't hear other midi file tracks and vice versa. I keep switching input and output sources in the control settings but it seems like I either have to use all midi tracks or all audio tracks. Same situation with playback. I know this is wrong but am totally stumped. Any advice would by awesome.

    Dave, You might need an external DAW to do this, I got it working and I'm an idiot. There is only one I/O for logic and if you use it for the audio recording it's not available for the sounds you want to have coming out of logic. I have Roland Edirol UA-25USB2 and it works like a charm, If I understand what I did correctly, the sound and MIDI messages are routed via an Aggregate Device in the audio/MIDI set-up [you configure the device in the audio half] to the Edirol, and there are many extra functions to choose from-I avoid the 3.5mm audio out headphone plug by routing audio out through the DAW Edirol-much better sound quality than the mini stereo jack.

  • Silent monitoring and recording

    When a supervisor or agent presses the record button they get an error "error received from recording service. More information in log file". I have attached the log file, anyone have this before?

    Have you tried doing a resync?  That option is also under CDA.  When you expand Service Configuration, you will see Synchronize Directory Services as an option.  Try resyncing and see if that resolves the issue.

  • CRS monitoring and recording

    Hi all:
    We have CRS 5.0 installed with agents using softphones. Some of the agents work in different LAN than CRS. That LAN is connected to the CRS LAN thru a WAN link. Those agents cannot be monitored or their calls cannot be recorder. After some researching, seems that issue is with PC MAC source address, that are changed when going thru router, then it is not recording calls.
    Is there any solution or workaround to overcome this?
    Thanks in advance.
    W.

    In case of soft phones you really cannot do much you have to be able to tap into the RTP to be able to record etc.
    IF you have cisco phones easy solution is to plug the PC back of the phone powered by the same environment.
    please rate if it helps.
    Good luck,
    Baseer.

  • Project monitoring and Archiving.

    I am trying to find a way to back up all files, activities, web history, downloads, and so on from one mack bookpro to another. I want to do this in a nonvisible manner, preventing notifications, or any evidence this is being tracked.

    In environment of Lync Server 2010 deployment, you can disassociate Monitoring and Archiving with Lync Server pool in topology builder and deploy a new Monitoring or Archiving, then associate them with Lync Server pool.
    Check how to remove Monitoring and Archiving server at
    http://technet.microsoft.com/en-us/library/gg195802(v=ocs.14).aspx
    http://technet.microsoft.com/en-us/library/gg195751(v=ocs.14).aspx
    Lisa Zheng
    TechNet Community Support

  • Poor server performance

    I have a Lenovo ThinkServer RD440 running windows 2012 R2 with a RAID 10 running 3TB 7.2K drives using the builtin raid controller and the server performance is pitiful.I believe it is related to disk performance and we get very high Active Time % usually pegged at 100% and the Disk Queue length is usually above 6. Responce time(ms) is unusually high as well most around 70ms but C:\pagefile.sys is 1284ms.It is a file server but it does not get much use. I also run spiceworks and SEPM. Shutting down the services does not effect the active time or queue length. When i RDP the desktop frequency stops responding. I have contacted Lenovo's technical support and ran their hardware diagnostics and they state it has came back clean and would not provide further help...Anyone else have experienced this and have a possible solution?
    This topic first appeared in the Spiceworks Community

    I have a Lenovo ThinkServer RD440 running windows 2012 R2 with a RAID 10 running 3TB 7.2K drives using the builtin raid controller and the server performance is pitiful.I believe it is related to disk performance and we get very high Active Time % usually pegged at 100% and the Disk Queue length is usually above 6. Responce time(ms) is unusually high as well most around 70ms but C:\pagefile.sys is 1284ms.It is a file server but it does not get much use. I also run spiceworks and SEPM. Shutting down the services does not effect the active time or queue length. When i RDP the desktop frequency stops responding. I have contacted Lenovo's technical support and ran their hardware diagnostics and they state it has came back clean and would not provide further help...Anyone else have experienced this and have a possible solution?
    This topic first appeared in the Spiceworks Community

  • Monitoring and Testing Lync Server 2013 Performance

    Good day , 
    I have two questions :
    1 - Even though it is not recommended . How can I use Stress and Performance tool to test my production Lync Servers 
    using current users accounts and profiles without making any changes to AD or Lync topology?
    2 - What are the most important Lync server counters to be monitored and is it enough to use Windows Performance monitoring tool for that purpose ? 
    Thanks in advance,
    Best Regards Bisher Shbib

    Hi,
    For your first question, there are no stress tools currently available specific for Lync 2013 now. Here is a similar case may help you:
    http://social.technet.microsoft.com/Forums/en-US/f4032c4c-0b1f-4533-a04d-6c6526f4578a/stree-and-performance-test-tool-for-lync-2013?forum=lyncinterop
    For your second question, if you want to monitor Lync server 2013 and Lync client 2013 you need deploy Lync Monitoring server. You can refer to the link below:
    http://technet.microsoft.com/en-us/library/gg398199.aspx
    Best Regards,
    Eason Huang
    Eason Huang
    TechNet Community Support

Maybe you are looking for