Monitor communication channel in CCMS

Hi all,
Is it possible to monitor the communication channels in CCMS besides in RWB?
If yes, then how?
Regards,
Hui

You can monitor the sender and receiver service in CCMS, but I don't think you can monitor the commuication channels. (i am open to correction!)
http://help.sap.com/saphelp_nw04/helpdata/en/45/e32b64f87c6f74e10000000a1553f6/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/90/4e313f8815d036e10000000a114084/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/28/83493b6b82e908e10000000a11402f/frameset.htm

Similar Messages

Monitor communication channel error

Hi Experts,
I am doing a proxy to file scenario.
In my scenario I have requirement that if there is a failure in placing the file in the target location then an alert has to be triggered.
For testing this I have given dummy host in receiver file adapter (FTP) and activated it.
When I triggered the interface, it still shows as successfully processed message in PI message monitoring, though the file is not placed in target location. I would expect that this should be shown as error. The error is shown only in the communication channel monitoring. So even the alert that I have configured do not work. Could you please provide some inputs on how to tackle this situation?
Thanks and regards,
Prasad

Hi Prasad,
Gneral flow will be like this
Sender AdapterEngine --> Integration Engine -->Receiver Adapter Engine
As your message failed at third step i.e at receiver adapter engine ...it will not shown an error in integration engine(SXMB_MONI) as the message is successfully passed to adapter engine from integraiton engine...
By default if message fails at adapter engine it will retires 3 times after period of 5 minutes...automatically
And finally if all retries fails then message status will be set to failed and an alert will be triggered when the manual intervention is required to analyse the problem..
If you feels that the error is resolved and needs to resend the message again which can be done from MessagingSystem of the adapter*http://host:port/MessagingSystem/)
Hope this clears you
Rajesh

Communication Channel Monitoring using CCMS/Solution manager

Hi ,
I have configured everything in solution manager for message monitoirng of PI system, but my requirement is to monitor communication channel error in ccms.
Is there any possibilty to trigger alerts for communication channel errors ??
Regards
Veeramalla

Hi,
Please refer following threads
SAP Solution Manager and PI
In addition you can refer solution manager wiki:
http://wiki.sdn.sap.com/wiki/display/SM/WeblogsrelatedtoSolutionManager
Regards,
Deepak
Edited by: Deepak Shah on Feb 23, 2011 11:15 AM

XI communication channel missing in communication channel monitoring

Hello partners,
I have a problem with communication channel monitoring.
I have defined a communication channel of Adapter Type = "XI" in the integration directory.
I have also sent messages successfully via this communication channel.
But the communication does not appear in the list of available channels in the selection list of the communication channel monitoring.
Can someone tell me how I can get monitoring info of an "XI" communication channel?

Hi,
From SP17, you have a new feature
http://help.sap.com/saphelp_nw04/helpdata/en/44/46d1a56faf52d3e10000000a1553f6/content.htm
The Runtime Workbench has the following new functions:
● Component monitoring: Communication channel monitor
In component monitoring, you can use the new communication channel monitor to call information about the status of your communication channels and the corresponding adapters. You can also administrate your communication channels.
Unlike the adapter monitor, the communication channel monitor also provides current runtime information about the communication channels of individual adapters, as long as they are registered for communication channel monitoring.
To monitor adapters that do not provide runtime information to communication channel monitoring, continue to use the adapter monitor.
Regards,
Bhavesh

Testing the JDBC adapter communication channel

Hi
I've created an interface which gets the sender payload using a JDBC adapter.
Basis have installed the JDBC driver for the database where the data resides
I've configured the communication channel to poll every 10 minutes
So far nothing appears to be happening
Can I test the communication channel independantly?
Is there a procedure to make the communication channel active?
Is there an admin area where I can see if there is an issue with the communication channel.
I've checked SMQ1, SMQ2 and SXMB_MONI and there are no messages
I've also checked runtime workbench => adapter monitoring => communication channels but I get an empty list
all help will be very much appreciated

Hi Geoff,
It is not possible to check only the communication channel but we can check the complete scenario confogured in Integration Directory.
1. Open ID.
2. Goto Tools.
3. Provide the sender and the receiver parameters.
4. Also provide the payload in the Payload section.
5. Now, goto Test Configuration
6. Select Run.
This shows you, if there are any issues in the configuration.
Thanks,

Communication Channel Stop and Start

Hello everyone,
We are using XI along with MQ for queing messages to our 3rd party logistics. Due to some issues happened in the past, it is decided to stop and restart the MQ channels every weekend. Now the problem is, when the MQ is down, some of the XI communication channels will go down, and will not start automatically, when the MQ bounces back. Now this had created a manual activity every weekend to stop and start all communication channels.
Question is, is there any way we can schedule it as a job to stop and start the channels, at a specific time ?

Hi!
It is possible in scheduling the messages in XI...
1. But before doing this make sure that at what time you want to be schedule ?
2. Is that time will be uniform for every week or else is it may varies ?
3. If Uniform please make schedule or else if it is varying note the difference between those timings I mean
     If your Messages are flowing for every Tuesday and also every Thursday...., etc..
4. You can schedule what ever may be the time it is suppose if those timings are varying weekly once a
     day but in that single day or next day if it was more than once..then better scheduling the
      communication channels to be start for and to be process for that particular 2 days and remaining days
      it wont work I mean stopping Cc
5. Now when come to process...in scheduling...
a) Click RWB>Component Monitoring>Communication Channel monitoiing
b) Right side u can check Availability TIme planning option click that..a seperate window will opens
    THere u can observe these options..
c) also u can see the log
I hope it will be useful to you...
Availability plan--> ONCE /DIALY / WEEKLY/ MONTHLY based on your req select any one...
Create: to create the scheduling...
change: to change the existing one
Save: to save
Reset if u want toreset alll
Delete and copy also as u know these..
While creating you can again see these options 3 main TABS
details: --> Corresponding details
CC: select ur chanel
OPTION 2
In XI 3.O you can directly do scheduling there after selecting the radio button of any Comunication channel and there adjacent to Audit log u can see availability time plan other than rt side top corder..
I hope it will be useful to u
Regards
Amar Srinivas Eli

Communication Channel Strange Behaviour

Hi,
We are facing a strange behaviour with communication channel monitoring in RWB for JMS Adapter.
I am sending data from IDoc to JMS. Message is processed successfully inside Integration Engine of PI.Message monitoring in RWB shows status successful.But ,if I monitor communication channel in RWB, under cluster node --> cluster node for Channel 'X' shows status green & in short log - I got an message "JMS message processed successfully at 2009-04-17|05:25:06+0100;JMS & XI identifiers are ID :414d515 & 457e345 respectively".
This information is always updated, when i run my interface & shows the latest three enteries there with information provided above in bold.
But if i see the processing details for Cluster node (Where we usually see the processing of message with its Message ID), there is no entry with Time Stamp & message ID & explanation.
Any idea why such a behaviour?
Thanks,
Venky

Hi,
hmmmm..........strange............
just check if you have multiple server nodes and you are selecting the server node with msg processing and then whether in processing details you are seeing your msgs or not............
also check if the msgs are processed just now or are processed some hours ago - if they are processed some hours ago then may be you do not have their processing details available currently but if they are processed just now, then you should be able to see their processing details..........
if the problem remains, then ask your basis guys to restart your XI J2EE engine and see if you then able to get processing details for your new msgs.........
Regards,
Rajeev Gupta

Communication Channel - Integrating with existing iMS52 and iDS52

Hi,
Any one tried integrating Portal Server JES2004Q2 channels with existing iMS52 and iDS52?
How about schema? Did you use the existing Dir for configuration? Please share, as at the moment we are encountering problems even installing it. Anyway that's a different story.
Regards,

Use Runtime Workbench -> Component Monitoring -> Communication channel monitoring
U could not start or stop individual communication channel through Visual Admin. U can start or stop whole adapter through it.
Regards,
Prateek

Communication Channel Errors to be monitored in CCMS

Hi,
We have set up CCMS Monitoring templates for PI monitoring. We have a business requirment to send communication channel errors to the IT team via CCMS
We have configured ALERTCATEGORIES and defined alert rules. The communication channel errors result in alerts. These alert categories are visible under the CCMS PI monitoring template.
What is not getting transmitted is the alert long and short text in CCMS.
is there any way to achieve this?
Please point to how to guide or blogs for the same.
Thanks
Abhishek

Hi Amit...
Check the error i got when communication channel is red...
till now it was working fine.......i tested with a file which has unproper mapping ..and sent it....it gave an error...with mapping exception..(Please do remember..before i sent unproper XML....commmunication channel was green)
it often happen when i use unproper XML......
here is the messages it says
Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException: Exception in XML Parser (format problem?):'java.lang.Exception: Message processing failed in XML parser: 'java.lang.Exception: Column value '/102' too long (>1 for 3. column) - must stop', probably configuration error in file adapter (XML parser error)': java.lang.Exception: Exception in XML Parser (format problem?):'java.lang.Exception: Message processing failed in XML parser: 'java.lang.Exception: Column value '/102' too long (>1 for 3. column) - must stop', probably configuration error in file adapter (XML parser error)'
Edited by: Harsha reddy on Jun 20, 2008 10:01 PM

Communication channel monitoring (adapter engine) in ccms (rz20) available?

Hi,
we have problems in our xi system (PI 7.0, SPS10). The adapter engine can only be monitored in the communication channel monitoring, available in the runtime workbench!
There sometimes errors disappear. At the moment these errors accumulate!
Is it possible to view these errors/ alerts in the ccms (rz20) monitoring?
So we don't look all the time in the communication channel monitoring!
Have anybody an idea?
Regards,
matthias isenburg

Have u seen the discussion
Re: How do I configure an auto-email alert for Adapter engine errors
Regards,
Prateek

Regarding Communication Channel Error in Component Monitoring(RWB) in Dev

Hi,
In my XI dev Server when I check Component monitoring....Adapter Engine and CC monitoring are showing errors ( showing red
symbol)......
I think my RFC to File Scenario cannot be executed due to this.......I cant receive any messages in SXMB_MONI.....
Please help me......
Thanks,
Sudheer

Hi...
Still I am not getting any messages in the MONI.....
In communication Channel Monitoring it is showing green.......
In Component Monitoring Integration Engine:XID showing red.....CCMS Status: showing red and Adapter Engine Showing red......
Created RFC destination at ECC(of 'T' type) and gave ECC details....Then gave same details in Communication channel in XI.......
I did not created RFC Destination at XI.......
Should data to be passed to RFC or XI automatically pings the data......
When ABAPer executed RFC Connection its successful...but when he executes Functional module i.e test it is showing 'SYSTEM_FAILURE'.....
Thanks,
Sudheer

Reporting communication channel errors in emails from alert monitoring

Does anybody know how to capture the error message reported on the communication channel and send it in the dynamic text of the email configured for alert monitoring?
I get the mapping error messages but all other message container element values seem to be blank.
None of the container elements (standard) defined seem to have the channel error message. in PI 7.0
Thx

Hi,
You can get all the alerts that were captured by the adapter monitoring i.e, communicaiton channel errors etc.
we can also trigger similar alerts for Adapter also when any adapter truns in to RED.
in RWB->Alert configuration-> choose adapter engine errors also then you will get alerts for adapter failure also.
If you need create alerts for each communication channel. in RWB->Alert montoring->Adapter type-> instead of giving * select indival commnication channel
for this you need to have alter configured for each Commnication channel in Alrtcatdef and RWB. so for each in RWB you select corerspoding communication channel.
You can monitor the sender and receiver service in CCMS, but I don't think you can monitor the commuication channels.
http://help.sap.com/saphelp_nw04/helpdata/en/45/e32b64f87c6f74e10000000a1553f6/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/90/4e313f8815d036e10000000a114084/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/28/83493b6b82e908e10000000a11402f/frameset.htm
Thanks
Swarup

Automatic monitoring of operational communication channels

Hi,
Can anyone tell me if there is a possibillity to automatically monitor the runtime status of the operational communication channels?
For instance the forwarding of the messages from (RWB > Component Monitoring>adapter monitoring-->adaptertype) to CCMS or picking up these logs with the alert framework.
Manual monitoring is not an option because the number of systems to be monitored is to big, so an "monitoring robot" has to be created for this specific area. Most of the other area's are already covered by alert framework and CCMS.
I hope someone has experience on this.
Kind regards,
Ramon Boekel

Hi Ramon,
Please have a look at this.
/people/sap.user72/blog/2005/11/29/xi-how-to-re-process-failed-xi-messages-automatically
cheers,
Prashanth

Advance selection for source file-Error in communication channel monitoring

Hi all,
Referring to the link below:
/people/mickael.huchet/blog/2006/09/18/xipi-how-to-exclude-files-in-a-sender-file-adapter
I have developed my scenario in the same way.But due to the values <NOTHING>
in Mandatory fields Source Directory and Filename,i am facing problem in Communication Channel Monitoring as it shows an error;even though the end-to-end scenario works successfully.
Plase note that our scenario is not to exclude the particular file but to pick the files serially after a certain delay.
Kindly provide some idea about how can we remove the error from Communication Channel Monitoring.
Thanks & Regards,
Sudhir Tiwari

Sudhir,
In the sender file adapter, you have an option called "Processing Sequence".
By selecting ByName or ByDate you can make files get selected sequentially either ByName ( alphabetically ) or by the creation time stamp of the file.
In the sender file adapter also make the QOS as EOIO and give the QueueName as any value and the files will be processed sequentially.
Regards
Bhavesh

Communication Channel Monitoring Error

Hi...Experts,
we r doing RFC-SOAP scenario with out using WSDL file,
sender Communication Channel Monitoring getting error like this
Error in processing caused by: com.sap.aii.af.mp.module.ModuleException: call to messaging system failed: com.sap.aii.af.ra.ms.api.DeliveryException: XIAdapterFramework:GENERAL:com.sap.aii.af.ra.ms.api.DeliveryException: invalid content type for SOAP: TEXT/HTML; HTTP 403 Forbidden caused by: com.sap.aii.af.ra.ms.api.DeliveryException: XIAdapterFramework:GENERAL:com.sap.aii.af.ra.ms.api.DeliveryException: invalid content type for SOAP: TEXT/HTML; HTTP 403 Forbidden
In the Receiver Communication Channel Monitoring, getting error like this.
Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException: invalid content type for SOAP: TEXT/HTML; HTTP 403 Forbidden: java.io.IOException: invalid content type for SOAP: TEXT/HTML; HTTP 403 Forbidden.
how can i rectify these errors, pls suggest me..
regards,
Pasi.

Hello Pasi,
Error: HTTP 403 Forbidden
Description: The server understood the request, but is refusing to fulfill it
Possible Tips:
Path sap/xi/engine not active
HTTP 403 during cache refresh of the adapter framework - Refer SAP Note -751856
Because of Inactive Services in ICF Go to SICF transaction and activate the services. Refer SAP Note -517484
Error in RWB/Message Monitoring- because of J2EE roles Refer SAP Note -796726
Error in SOAP Adapter - "403 Forbidden" from the adapter's servlet. Because of the URL is incorrect or the adapter is not correctly deployed.
Go through Micheal's Blog..
XI: Timeouts
/people/michal.krawczyk2/blog/2006/06/08/xi-timeouts-timeouts-timeouts
Thanks,
Satya Kumar

Monitor communication channel in CCMS

Similar Messages

Maybe you are looking for