Monitor f1503 - blue led power light not showing power available. unable to turn on

Hi ,
I have had my f1503 monitor in storage for a while and it was working at last usage. Connected all power and PC connections correctly and turned the power on but no blue led light working and unable to turn on the monitor. Checked the power adaptor - green led lit on power transformer and 12.33 volts were showing at the output end of the monitor power plug. The monitor power plug was inserted into the correct socket. Please help?
Does the monitor have a fuse that may have blown?
This question was solved.
View Solution.

Hello Bruce123456,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that you are having issues where your HP Pavilion f1503 Flat Panel Monitor is not coming on. The issue you are describing appears to be a physical issue and I think it would be best if you contact HP Technical Support for repair options.
I would like to thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Similar Messages

Linksys Wireless-G router power light not glowing

Hi,
I bought my Linksys Wireless-G 2.4 Ghz, 54 Mbps Broadband router (Model: WRT54GL) in US. I'm using the same in India for the past couple of months (connected thru 240 to 120v voltage converter). It was working fine until last week. All of the sudden I see the Linksys router power light not glowing at all. Initially I suspected the problem to be with voltage converter, later I figured out that the voltage converter and power adapter to router are working fine. So its the issue with wireless router. Is this a known issue with this model ?. If so how do I fix this ?. Is there a Linksys wireless router service center in Bangalore ?.
Any help related to this issue would be great.
Thanks in Advance.
Regards,
Siva K.

Thanks for your immediate response on this issue.
Well, there is no power to the router at all. So as you mentioned I believe the router is dead. Is there anything we can do now ?.
Note: This is a pretty new router. I haven't used it much.
Regards,
Siva K.

Sudden shut down, left with blinking power light (NOT in sleep mode)

Last night I boosted the RAM on my iMac G5 20" from 1.25GB to 2GB (added 1GB from Crucial.com). This morning I have twice experienced something I have never come across before.
I was using Garageband (my most memory intensive app) and the iMac just shut down w/o warning. I was left only with a flashing power light (and the power light on my USB music keyboard was flashing, too). It was NOT in sleep mode, and at first it would not start up again at all. It continued flashing even after the power was disconnected. After a few minutes the power button eventually started up the computer again.
This exact same scenario has occurred twice in 30 minutes.
A search of Apple support has simply told me that the flashing power light is to indicate sleep mode. Again, the computer was definitely not sleeping.
Any thoughts? Your help would be much appreciated.
iMac G5 20", 1.8 GHz, 2GB RAM Mac OS X (10.4.8)

Welcome to discussions - have you tried removing your new RAM stick to see if the problem goes away? You might also try resetting your SMU.
Please post back.
Miriam

WD MyBook World Edition White not showing as available disk

Hi
I have until recently been able to backup to our WD disk at the office.
Later TM reported issues with backup.
The disk is not showing as available to TM.
We have three other MacBooks at the office and they can see the disk, but I can't.
I have googled and read the FAQ here but none was applicable to my problem.
I have read forums at WD but nothing found.
MacOS is updated
WD firmware updated
Please help
/Mike

hakuseki wrote:
Hi, and welcome to the forums.
Later TM reported issues with backup.
WHAT issues? The messages likely explain the problem. Without a hint of a glimmer of a clue, there's not much we can suggest.
The disk is not showing as available to TM.
Can you see your Mac's +sparse bundle+ on it via the Finder?
I have googled and read the FAQ here but none was applicable to my problem.
Start with [Time Machine - Troubleshooting|http://web.me.com/pondini/Time_Machine/Troubleshooting.html] (or use the link in *User Tips* at the top of this forum). It will show you how to locate the message(s) that describe the problem, then help you fix it. If that doesn't help, post back with details, including all the messages, what you've done, and the results.

My play/pause button on my Ipod Classic is not working, I am unable to turn off my Ipod or push play. Can this be fixed?

The play/pause button on my ipod classic is not working, I am unable to turn off or push play on my ipod. Is there away to fix this?

Do other devices now connect?
Did the iPod connect before?
What encryption/security is the router using?
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Running Applications Light Not Showing In Dock

Hi all, on my new iMac, I changed the dock to the old style, tiger, with a terminal script and then changed it back and now the little lights that show when an application is running do not appear? I've tried trashing the two dock files in Library>Preferences and it does not fix it. Any help would be much appreciated as I have no idea what apps are running unless i open the activity monitor.
Thanks

fixed it, the files in System>Library>Core Services>Dock had been deleted. The little png icons that is. Yay!

Power View not showing on opening workbook in Excel 2013

When I re-open an Excel 2013 SP1 workbook with a Power View sheet, the Power View is coming up as disabled. To get it back, I have to insert a new Power View sheet. This then starts up PV and the sheet is shown properly.
Does anyone know how to get PV to show on start-up so that I don't have to insert a new PV sheet each time?
Paul

Hi Paul,
Based on my research, I think this issue is caused by having turned off the Power View add-in from Excel Options. To troubleshoot this issue, we can refer to the following steps:
Set the Formula bar as visible in your ribbon
Enable add-ins of power view, please go to File>Options>Add-Ins
In the Manage box, click the drop-down arrow > COM Add-ins > Go.
Check the Power View check box > OK.
If this issue still exists, please try to repair Office in Control panel>Program and features>Right click Office 2013 and repair.
The following document about Create a Power View sheet in Excel 2013 is for your reference:
http://office.microsoft.com/en-in/excel-help/create-a-power-view-sheet-in-excel-2013-HA102899553.aspx
Hope this helps.
Thanks,
Katherine Xiong
If you have any feedback on our support, please click
here.
Katherine Xiong
TechNet Community Support

Quicksilver Power Light Not Going Out On Shutdown

I shutdown a Quicksilver I've been working on. The light on the power button, and seems a little dimmer than normal. Now the computer won't startup. Have disconnect the power chord, but the light come back on when I reconnect the power chord. What can I do?

Hi, Jim -
You stated the problem clearly enough.
Many models, particularly G3s but also many G4s, will exhibit starting problems when the internal battery is too weak or dead. The expected life of such batteries is about 4 or 5 years, considerably less if the machine is unplugged regularly or for an extended period.
"PMU" stands for the Power Management Unit. When it gets out of kilter (which can happen from a weak or dead battery, or as the result of a power outage), odd starting problems will occur. Fortunately it is easily reset.
There are another couple of possibilities:
• The power supply unit may have gone bad.
• The front panel board (a small printed circuit board behind the power button, on which the button is mounted) has gone bad. Relatedly, the small ribbon cable which connects that board to the main logic board may have got caught beween frame parts when the side door was last closed.
It is better to first eliminate the two possibilities I gave above before assuming that either of these others may pertain.

Films in itunes library not showing as available to sync?

I have around 8 films listed in my itunes library but 6 of them are not showing up as available to sync to my ipod touch. I have bought all the film through itunes with the latest only the other day; it is this film and the previously bought film that are the only ones showing up as available to sync. I have successfully synced film and TV before to my ipod but out of the blue seem to be having trouble this time.
In saying the only 2 are seem to available to sync when I do try to sync them they are not showing up on my device, even though the memory bar of the ipod shows that a number of GB of data has been added; they are there but they're not no matter how much I search my device or tick and untick 'sync' and 'unsync'.
Can anyone help me find out why the films I do 'seem' to be syncing aren't showing up on my ipod touch and why none of my films in my library are showing up for syncing anymore?? Thanks.

- Have yo used the Spotlight search on the iPod. Maybe yu just can't find them
- Do the non-syncing ones play in iTunes on the computer?

Custom color profiles not showing as available in InDesign CC

This is a college graphic design lab environment with iMacs running 10.9.4 and the CC versions of Adobe programs
We have a variety of custom color profiles for our specific printers and media. They're located in a special folder and an alias of that folder is located in /Library/Colorsync/profiles. The profiles in that folder do not show up as available for selection in InDesign CC. They did before the upgrade to the CC version. They do show up in Photoshop CC, Lightroom 5 and Illustrator CC. Is this a known InDesign flaw? Any ideas for a fix... preferably one that doesn't involve moving the profiles?
Thanks
Bob Smith

I had the same issue when playing with my Xerox Phaser 6110 profiled with colormunki. All software except Aperture (3.0.3) recognized the profile (Color Sync, Print dialog, Preview soft-proffing, even LR 3b2). I too tried all possible locations and none worked.
Then I opened the profile in ColorSync, and edited (Profiles -> Xerox... -> Open ->'desc' tag) Ascii and unicode descriptions to read aaa.icc and did a Save As aaa.icc and there it was, available in Aperture, too.
To my great disappointment the soft-proof feature in Aperture seems to be broken for some monitor/printer profile combinations, and is compatibly broken for printing from Aperture. What happens is the resulting image is way too degraded, even beyond the (admittedly crappy) photo printing capabilities of this printer.
IOW printing the same JPG via Preview and/or soft-proofing with the printer's profile yields way more consistent results. Totally unacceptable for a €200 piece of software.

Ssrs parameter default value not showing ,when available values is binded to query dataset

I have developed a report using sql server data tools for vsiual studio2012 ,i have defined few parameters ,on one of the parameter when available values is binded to a dataset query, the report default value is not showing in report preview .
Many Thanks
Chandra

Hi Chandra,
According to your description, you have set the default value for a parameter, but it's not displayed when initially running the report. Right?
In this scenario, since you have set the available values bind to query, so your default values should be within these available values. If these default values are not within the available values, the default values will be not displayed. So please check
the default values.
Reference:
Add, Change, or Delete Default Values for a Report Parameter (Report Builder and SSRS)
If you have any question, please feel free to ask.
Best Regards,
Simon Hou

Creative Cloud Desktop not showing updates available.

Several students in my design class are running into problems where their Creative Cloud Desktop is not showing that there are updates to their applications. I was discussing some new features released for CC 2014 last week at Adobe Max, and would require them to be running the 2014.2.x.x (or .1) versions of several applications. I verified that each student, for example, is still running Photoshop 2014.0.x. and I have .2.0.
On one students machine I had them uninstall and reinstall the Creative Cloud Desktop application – the new installer was downloaded from Adobe, so it should be the latest update.
Lastly, I had them remove the .db file from the OOBE folder in their Users director, to see if it would force a refresh – no effect.
I can't verify that this is consistent across all machines, but I think nearly all of them had started by installing the trial of CC2014 - and then subscribed (on my recommendation) in order to have the appropriate software for the course. I'd hate for them to all have to uninstall and reinstall from scratch...
Thoughts?
Stephen

Hi,
Try this :
_Close CC desktop .
_ delete "AAMUpdaterInventory " et "AAMUpdater" (if present ) in :
MAC :
/Users/[User Name]/Library/Applicaiton Support /Adobe
MAC HD//Bibliotheque/Application Support /Adobe
WIn :
C:\Users\[user name]\AppData\Local\Adobe
C:\Program Files (x86)\Common Files\Adobe
Launch CC desktop .
Try also to search for updates from applications help menu.
Good luck .

Not showing the available contexts?

Hi,
When I am running a report in WebI, its running fine. Wehn I open the report in Edit mode, in the query's its shown the context name in the query properties. When I try to edi the query, and even though, I restore the same objects in the query panel, its asking for context. But its not showing the actual context. Its showing other contexts.
Could anyone faced this kind of problem?
Any help pelase.
Thank you,
Regards,
Gowtham Sen.

Hi Gawtham,
I would suggest you look at the universe and check that the objects are being defined correctly i.e by checking the class and source table.field and double check that the contexts have been defined correctly.
Regards
Jacques

I have an i-pad mini and can not synch my music to the i-pad. I have attached to my PC, and the music does not show as available on the i-pad. I have selected to synch all with a check mark ... same as i-phone. i-pad shows no music avaiable.

I have a new i-pad mini and I can not get music to show as available on the i-pad. I have tried to download from cloud and also have physically attached the i-pad to my PC. Have selected to synch checked songs ... just like my i-phone .... but no music is available on the i-pad. Trying to use same synch parameters as the i-phone

How to use multiple iDevices with one computer

Crystal Reports Cross-Tab Report not showing all available fields

I am running CR2008 against MS SQL Express. I have several tables with fields and data in them and can create standard reports to show all the data in all the fields. However, when I try to create a cross-tab report, only some of the fields appear for me to choose from.
I created a standard report with all the fields I needed in my cross-tab report and ran a preview. Everything was there. I then added a cross-tab object, selected the tables only to find that fields that are in the main report are not showing up for selection in the cross-tab.

UPDATE: I exported the entire database from MS SQLExpress to MS Access and I am having the same issues, so it does not appear to be a problem with the database engine and, since the standard tabular reports show the fields, I am at a loss as to why they don't show up in the cross-tab or the Parameter fields.
I am creating the cross-tab through the Cross-Tab wizard. Is there maybe a bug in that? Is there a way to create it otherwise?

Monitor f1503 - blue led power light not showing power available. unable to turn on

Similar Messages

Maybe you are looking for