Monitor Failure

My monitor won't come on. Every time I try to get it to come on I get "No Input Signal" then it jumps to "Monitor Going to Sleep" before I can even attempt to change the input selection. Is anybody experiencing this problem?

Hi
if you're comfortable "getting under the hood", open the box and make sure your video card is properly seated by gently rocking it back and forth in it's slot. Also make sure the cable are connected tightly.
or
First test your monitor with another system, with the same vidoe cable which are currently using...
if still getting issue then try changing the video cable..
if both are ok.. then problem is your video card..
if you have a video card installed in your system then remove it and clean head of the vide card and put it back...
if the card is inbilt then problem could be your video chip..
post result here..
**Clicking on the Kudos! white star is a nice way to say thank you on any post that helped you or resolved the problem.**
**Selecting "Accept as Solution" for a reply that solves your issue helps others who are searching the web for an answer**

Similar Messages

InfoPackage Load Monitoring failures to email

I need information on how to setup load monitoring to email. I already do this within process chains but need to do it when I am running an initial load without a process chain. Is there settings within the system that can be setup to send an email out to the alert me to these failures so that I am not stuck to watching them in the monitor in BW.
Thank you!
Caroline De Laurell

One last question...
Does SAP have a standard event in this list that will send an email if it passes or fails. Or do I have to have someone create an abap program for that?
Thank you for all your assistance!
I will give you points after the return response.
Thanks!
Caroline

Flat panel monitor failure

My G4 moitor has failed. Does anyone know how I can use a networked mac to see both partitions on the G4 hard drive and and what software is available & necessary to copy the old hard drive contents to a new machine. If there is no way, I am in deep weeds.
Do you know wheter the G4 hard drive is of a physical size that could be installed in a new Pro desktop?
Recommendations please.

Hello and Welcome to Apple Discussions.
I wish it were under better circumstances. Unfortunately you aren't the first and won't be the last to see a total loss of video on an iMac G4.
Firstly I'll answer your questions but after I'll suggest a couple of other options.
1. Networking this machine will be awkward in this state due to the configuration required. Luckily Apple has built in Firewire Target Disk Mode which allow you to use any Mac as an external hard drive:
Connect the two Macs with a 6pin-to-6pin Firewire cable.
Switch on the iMac G4 and hold down the T key.
Switch on the other Mac.
The iMac G4's hard disk (and optical disk if there's a DVD in there) will appear on the other Mac's desktop.
Copy your data across
When finished drag the iMac G4's hard disk to the Trash on the other Mac.
Disconnect the FW cable.
Power down the iMac G4 using the power button.
2. You can drag and drop your own files but you could use a cloning applications like:
Carbon Copy Cloner, or,
SuperDuper.
3. You don't say exactly which iMac G4 you have but they shipped with between 40Gb and 160Gb. The Mac Pro ships with at least a 160Gb drive. So you should have no issues.
4. There are also some other considerations:
Firewire Hard Disk Enclosure. Put the iMac G4's hard drive in an enclosure. For a few dollars you can buy and enclosure and continue to use the drive.
Use an External Display. You can purchase a $19 adaptor to continue to use the iMac G4 with either a TV or computer monitor.
Consider the repair cost. If you can shine a Torch on the current display and still make out an image then the repair will be relatively cheap.
If any of these three sound appealing we can explain further.
kind regards and let us know how you get on.
mrtotes

Lastest Apple Update Causes ext. Monitor Failure

I have reason to suspect the latest round of software updates from Apple have caused the colors on my external to not render correctly in Mirror Mode. RGB colors are mixed and scattered across the screen.
I suspect the update because the monitor's menu system renders fine on top of the color mess and this is first time I've connected to it since updating yesterday.
The only other possibility I can think of is the DVI port or cable is malfunctioning, but I think that's unlikely because it worked fine right before the update.
My wire connection is the Apple supplied mini DVI to HDMI cable to Phillips 190B LCD display.
Appreciate any opinions here
thx

I have the same problem, and it also began when I updated to 10.5.5
I have also noticed that the image is fine when in extended desktop mode, it just won't mirror the desktop correctly.

Dual monitor failure! (FX5200)

Well, 2 days ago I connected a second CRT monitor to my MSI NVidia FX5200 VTD128 card via the addapter given with the card.
It was working ok, though the refresh rates were noticeably slower on both monitors when both monitors were active.
Then I started getting little flickers, even though there was nothing going on, which was a little strange...but I figured it was ok.
So I was working with powerpoint, Macromedia Flash MX, Windows Media Player, etc. and I started having some problems, especially with Powerpoint. I'll use powerpoint to explain what happened: While previewing my presentation the 2nd (older) monitor was where the presentation was being displayed. It usually didn't take long for the screen to flicker a bit, and change the vertical and horizontal size of the display, to something that was just not right. I could reset it back to the orizinal resolution or v/h sync by going into settings and changing the resolution.
Well, then it happened again, but this time the entire image was lost! Now I can not get an image to that monitor while in windows...works during startup though. Please help.

Sorry, I really had to leave earlier.
I got the two monitors to work together again, but this time there were some limitations, and it eventually led to the same end as before.
As far as I can tell it is a windows problem or a video card problem, not a power supply or motherboard issue. I should have said that earlier. I believe it to be a video card problem, which is leading to a windows problem.
So as I said I have the FX5200 VTD128 card, running on a 4x AGP slot with NVidia drivers (not MSI drivers as these do not work on my system). My case temperature is fairly constant at approx. 81 F, and I don't know the temp of the video card.
The first time I had a problem I was using the DualView option, where both monitors are separate pretty much. After a few hours of working nicely the monitor started having so problems...it would blink an come back with a picture that was very narrow and extremely tall (both more than what could be fixed with the monitor controls). Also the colour was dull and dark. Eventually after fixing this problem a few times by changing the resolution to reset the monitor, the computer crashed. When I restarted windows the second monitor remained black while in windows (though I still see all the start up stuff on it).
So today since I couldn't get the Dual View option to work I used the option that spreads the image over both monitors. Exact same thing happened a few hours after use.
Since I had restarted my computer over this period of time, I am pretty sure it is not a memory thing. I'm guessing it is a heat thing. I have a feeling the fan on the video card is not working like it is supposed to without the MSI drivers. If this is the case, MSI should be responsible for informing buyers about this problem.
Since I was using different programs both times, I'm pretty sure it is not related to what programs were running. And since the monitor was working no problem earlier, I don't think it has anything to do with the hardware in my computer, though I tried to provide some info earlier...though I do believe there was enough info there for a somewhat educated guess as to what my problem could have been.
I have a feeling this will have to go to MSI support to get any type of answer, but hopefully someone else has a good idea as to what it is and what can be done about it.
Thanks
PS.
Richard, I believe the 4 wheels would be the equivelent of me saying I had a video card....the h/v sync thing would be like saying the car is making a specific noise. Welcome to the life of a mechanic. I appreciate help, but please refrain from the sarcasm.

Monitor failure on boot

I have OSX Leopard fully updated and XP Professional fully updated on MacBook Pro and it keeps overheating and monitor is not working? Has anyone else experienced this? Are there any boot proceedings I can use to get screenback. It's clearly not damaged, there is a software issue somewhere.

Welcome to Apple discussions!
While your Mac may seem old to you, Macs last a long time. Your Mac is not a bona fide Older Mac.
Most readers in this "Older Hardware Products" forum are using Desktop and Tower Macs that were produced before the turn of the century. iMacs have their own forums, too.
The forums in the link below are visited by users of MacBooks, who are much more likely to be able to offer you accurate advice on a problem like yours. I suggest you choose a specific forum (you don't get a "post new topic" button until you select an individual forum, not the composite one first shown) create e new topic there, then cut and paste your query from above. Adding the processor speed of your Mac is very helpful on homing in on exactly which model it is.
Apple.com > Support > Discussions > MacBook Pro

10.4.7 and monitor failure after boot up

10.4.7 again. I have some strange experience with my core duo mini, after installing the 10.4.7 update. After the boot procedure I get a blank grey screen with some flashing in every seconds on my Xerox LCD display. It looks like the monitor is on "energy save" mode or something like that because this flashing is abnormal. So at this stage i cannot do anything, except push the "power on" button of my mini to get it sleep. After the "wake up" the monitor works perfectly.
I got te same error when my system put my monitor into "energy save" mode after some inactive minutes. For this problem i can switch off this energy saving, but for the problem during the process i have no idea.
Anyone have the same, or have some guess about the solution?
Mac Mini Core Duo Mac OS X (10.4.7)

Both. Don't forget to reboot afterwards so the system can generate new files.

Launch monitor failure

At start up I get an alert stating "Application Launch Moiitor. Transport monitor failed to launch" followed by what looks like a specific file. What does this mean and how do I correct the problem?? Thanks.

Using Mac OS X Tiger seems appropriate.

T61 Dual monitor failure

I'm using a Lenovo T61 with WinXP. This problem is a bit odd and lengthy.
LONG VERSION:
I usually work from home, and instead of shutting down my computer for the commute to work, I'll put my laptop into sleep mode. When I get to work, I'll usually put my laptop into the dock, flip up the screen and take it out of sleep mode. When I do this, only the external monitor kicks on. When I try to extend to my laptop monitor for dual monitors, the laptop monitor accepts the change, re-sizes resolution, then turns off.
SHORT VERSION:
Dual monitor on the laptop screen will not enable when i dock my computer from sleep mode.
Thanks for reading!
Solved!
Go to Solution.

Well, if anyone ever has this problem, I actually figured it out while closing to go home today. If you lower the monitor down just before closing it, the screen will flicker off back to the laptop, then open it back up, and it appears to be able to go into dual monitor mode after that.
Strange..... or maybe I'M just strange!

Mid-2011 iMac monitor failure?

Recently (last few weeks) my screen has started to act up, with patterns of small squares mismatched with the background 'blinking' (about 1 Hz) on the screen with somewhat random appearance. I have seen no link to which apps are running, or whether or not I'm networked. Location is not consistent, but seems to be most evident on user-RightHandSide of screen.
Mid-2011 27" 2.7GHz Intel. AMD Radeon HD6770M graphics with 512 MB. running OSX10.0.3 (13D65).
Anybody else see this or know what's up?

I had the same problems on my Mid 2011 Thunderbolt iMac.
External monitor would sleep cycle when connected.
My only solution was to get an 3 in one Ebay Mini DP/Thunderbolt adapter then connect a HDMI to DVI cable to that, with the DVI end of the cable going into the monitor.
There must be a signal issue preventing proper sleep using Mini Displayport/Thunderbolt to Displayport connections for external monitor output.
Here is what my Systems Information Graphics/Display outputs:

Preview in Source Monitor Failure - The Importer reported a generic error

Hello,
I was wondering whether anybody might be able to help me? I'm pretty new to editing and using Premier Pro so this could be something very simple.
I've shot a load of footage on a Sony PMW200 (shot 1080/25p) and copied all my footage onto a G-Raid external hard drive. Every time I try and open a clip or drag it onto the timeline the below message appears. I have no idea what the problem could be. I was wondering whether anybody else has ever come across this problem or had any idea what it could be?
All help is greatly appreciated
Thank you

What version of Premiere Pro?
I don't use it, but I think MXF does not work in earlier versions
Go back to Premiere Pro and, in the box right under Begin a discussion type in MXF (and do NOT hit the enter key or you are starting a new discussion !!!)
Wait a few seconds for the search function to activate, and you may read previous discussions that contain mxf

Failure Upgrading Monitoring in GMS 2.0.1

We just completed (incompletely) upgrading our Data Synchronizer from 1.2.5.299 to GMS 2.0.1. Everything appeared to go fine for the most part, except the monitoring. The server has been tested, and data is flowing properly, but we cannot get any stats off from the Dashboard.
During the update, there is the following:
shutting down GroupWise Mobility Service... done
Updating prostgres settings... done
Restarting postgres.....failed
done
<the rest of the upgrade goes fine until...>
Updating Monitoring
Failed upgrade monitoring: Failure in: su root -c "rcpostgresql restart"
done
A reboot of the server has postgreSQL working fine. However, we can't get our monitoring working until we can let the system restart it. For what it is worth, this was a problem when we were running Data Synchronizer also.
The server originally started as a SLES10, and has been upgraded incrementally to SLES11 sp2.
Any help is appreciated. I am still a Linux newb, so I may need some help in that area also (command-wise). Thanks in advance!

Ok, I apparently can't find where to update my thread either. I did some searching on the forums, and found TID 7008132. I added the following lines to my pg_hba.conf file:
local all postgres ident sameuser
host all postgres 127.0.0.1/32 ident sameuser
host all postgres ::1/128 ident sameuser
Now, what that did, was that it enabled postgresql to restart properly. What it also did was bork the rest of gms. When doing a "rcgms start", I had some errors. It said:
Checking for gms monitor: unused
Checking for gms config: running
Checking for gms engine: dead
Checking for gms web admin: running
Checking for gms agent manager: running
Seeing the "dead" on the gms engine, I removed the lines and rebooted the machine. Everything came back up so it now reads:
Checking for gms monitor: unused
Checking for gms config: running
Checking for gms engine: running
Checking for gms web admin: running
Checking for gms agent manager: running
Monitor is still unused, but I believe that is due to the update.sh script not being able to restart PostgreSQL, and erroring out on the Upgrading Monitor section.
To me, this all screams user or permissions, but I don't know where to begin for that.

Monitor (hp 23xi & 25xi) displays "Scanning No Signal" then to sleep but other monitor works ok.

About 7 months ago I purchased an HP 23xi IPS to replace a burned out ViewSonic flat screen for my desktop (HP Pavilion a6050e, PN: GC382AV#ABA, SN:[Personal Information Removed] running Windows Vista Home Premium OEMAct 32 bit, with a NIVIDIA GeForce 7500 LE display adapter). The 23xi worked perfectly until a few days ago at power up it just displayed “Scanning: No-Signal” as it scrolled through the auto-detect options (HDMI, VGA and HDMI). After a couple scans it goes to sleep. I checked the cables, switched between HDMI and VGA cables, tried new HDMI and VGA cables. Finally I drug out my old hp pavilion mx90 CRT and connected via VGA and I finally got a normal signal (this is the only way I can write this).
I tried multiple combinations of shutting down, unplugging, rebooting. Convinced it was a problem with the 23xi I took it back to the retailer who was kind enough to give me an exchange with an upgrade to a brand new 25xi which I hooked up and ran the startup disk that it came with and still the same problem. The startup disk dialog insists that the drivers are loaded but I don’t see it in my device manager. I also downloaded the latest drivers for my video card from NIVIDIA and rebooted. I ran a cleanup using Norton (fixed 3 invalid registries); still, no luck. Again, no problems when using my old 30 lb mx90 monitor, screen saver is working too.
However, every once in a while I get a dialog box at start up describing a monitor failure (I didn’t think to copy the full text of the first one which stated, in part:
Problem event name: App Hang B1.
App Name HP Display Installer.exe,.
version: 1.35.0.1,
Hang Sig: 71c1. Hang type: 0.
And the full text of the latest such dialog box reads:
Problem signature:
Problem Event Name:       APPCRASH
Application Name:            DTHtml.exe
Application Version:         1.2.0.100
Application Timestamp:   502ed5d6
Fault Module Name:         pdi_nv_legacy.dll
Fault Module Version:      1.0.0.1
Fault Module Timestamp:               48473a21
Exception Code:    c0000005
Exception Offset:   00001927
OS Version:            6.0.6002.2.2.0.768.3
Locale ID:               1033
Additional Information 1: aed1
Additional Information 2: aad416d1892f5779e260a3742d62a0f4
Additional Information 3: 8af1
Additional Information 4: 3cc29b1a3adc5a2d247eb19195254d12
Any advise is hugely appreciated!
Thanks

Hi spica9,
Welcome to the HP Community! I see that you are having problems setting up your HP 23xi IPS. Try installing the drivers in safe mode in case something in Windows is blocking it. You can use the CD or go here to download the drivers. Another option is running the HP Support Assistant to see if detected anything that needs to be updated.
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

Monitor HPw2207h only comes on with re-boot goes black and error says no imput, win7 64bit

No changes just started a couple of months ago. when it goes to sleep hitting a key or moving the mouse will not wake it up and it gives me an error "no imout vga,no imput hdmi" and then going to sleep? Omly way to get it back is to reboot!

>will not wake it up and it gives me an error "no imout vga,no imput hdmi"
This is not a monitor failure but a pc problem ....
Which pc model? Which os?
How is it connected to the monitor? (Which ports/cable)
Have you tried to disable power save of the pc?
Do you have the most current driver for the gpu?
*** Say 'Thanks' with Kudos ***

GRC 10 ALERT MONITOR: FALSE/POSITIVES BIAS CALL TRANSACTION

Hi, everybody. I had an Issue related with GRC AC 10 alert monitor that is reporting that some users triggered SoD risks TR54 , TR01 and TR03 originated by transactions: ML81N - service entry against purchase order and FB05 - post with clearing. Both transactions are not available for those users because they don´t have the authorization profiles in the UMR or available in dialog mode.
Nevertheless we observed that both actions (ML81N and FB05) were invoked by a "CALL TRANSACTION" instruction from another program report.
I believe that this is a false positive alarm that were triggered even though the users have not assigned roles or functions of risk.
I will appreciate your comments.
Best Regards.
Victor Sarabia
IT GRC Manager

1) How do I not alert on first failure but initiate an immediate retry in 30 seconds and if retry fails then alert. This prevents false positives and is a feature that products such as uptrends performs as default
SCOM has no that kind of feature
2) How do I alert on with just one alert of transaction failure instead of each of the components of the transaction monitor failure. Example our first failure threw 10 alerts encompassing each part of the transaction
a) Right click web application transaction Monitoring object --> View Management Pack Object --> View Monitors
b) Expanse the web application transaction monitor --> entity Health --> Availability --> Web Application XXXX
c) Open the monitor properties of Request X -XXX and uncheck "Generate alerts for this monitor"
3) How do I create an uptime report to show monthly and quarterly uptime for the website based on the transaction monitoring.
a) go to Monitoring workspace --> Web Application Transaction Monitoring --> Web Application State
b) select the web application transaction entity and click Availability Report task on task pane
c) Select the report period and run
Roger
Roger

Monitor Failure

Similar Messages

Maybe you are looking for