Monitor Goes Brighter when CS6 Opens

I noticed that when I open CS6 the monitor goes brighter than the calibrated display.  When CS6 closes, it goes back to the darker calibration.  When I open LR, the monitor brightness stays the same.  I checked my settings and the calibrated profile is the default.  I have a Samsung laptop with Radeon ADM graphic and Intel Core i7,  using Wndows 7.  Can anyone direct me to fix this?

This is the Lightroom forum - the Photophop forum is here:
Photoshop General Discussion

Similar Messages

  • Screen goes out when cover opened

    I have a white Macbook.  When I open the cover the screen goes out unless it is held at a certain angle.

    It's one of four things and the liklihood in this order:
    1) Inverter Cable
    2) Inverter
    3) Screen
    4) Logic Boarad
    If you're Macbooks under warranty take it to an Apple Certified Technician (Apple Store) and have them take a look at it. If not, and you can't afford to repair it, you're welcome to take a gander at repairing those parts. If you have the time, and can figure it out, try opening up the chasis reconnecting to cables to the monitor, as on some laptops they're taped on and eventually come lose.
    This will likely void any active warranty.

  • How do I change what page Ffirefox goes to when I open a new tab?

    I want my page to go to the default "about:blank" page when I open a new tab. But my mother installed a software that forced a new tab to go to a Yahoo search bar page. Is there any way to change it back?
    I have checked my add-ons and uninstalled any pertaining to Yahoo and it still persists.
    Using version 7.0.1.

    Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
    *Don't make any changes on the Safe mode start window.
    *https://support.mozilla.com/kb/Safe+Mode
    *https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

  • FCE4 - Capture window goes red when Safari open on my second screen

    I have a Mac Pro 2008 Model with an nvidia 8800 graphics card and two 20' screens.
    When I capture any video into FCE4, if I have Safari open on my other monitor, FCE capture window goes red and I am unable to view footage being imported. Exit out of Safari and the capture window appears. Sometimes, only half the window is red (diagonally)!!
    Is there any software fix for this or does it mean anything else?
    Thanks in advance
    Matt

    Have just checked with Firefox and it doesn't happen!! :-))
    I only have one user on this mac and that's me.
    My wife and two sons rarely use this machine as I use it for work.
    Maybe I should have a second user just to check things like this out!
    Thanks for your help.
    Happy New Year, Matt

  • Monitor profile unloads when games open?!

    okay, so after a long time of wondering why quake 4 on one computer looks hideously green and it looks just fine on my powerbook, i realized that when quake 4 opens, the monitor profile is UNLOADED.
    now, i dont have any other games installed on the one computer so i cant test other full screen things, but i would imagine a similar issue. so, what in the heck is going on?
    any ideas? =(

    Manufacturer-supplied profiles are notoriously unreliable and often outright defective. The problem is that they are often pushed through Windows Update to unsuspecting users. Avoid them. If you click "hide this update" the next time it comes up it won't come back.
    The Photoshop message means what it says. Choose "Ignore" to throw it out and replace it with the Windows default, which is sRGB IEC61966-2.1. The proper fix is to make a custom profile with a calibrator, but if you don't have one it's always best and safest to use sRGB.
    The manual way to do this is to go into Control Panel > Color Management > Devices. Relaunch Photoshop after you've changed the profile (it needs to pick up the correct profile at startup):

  • Program monitor goes blank when editing certain clips

    A few days ago a 2 new problems occurred.
    1.
    The project I have is sett to 720, 24 fps.
    The clips I use is from 5D MK3, shot in 720, 50fps.
    Some of the clips I made duplicates of, and interpreted to 24fps for a slomo effect.
    The 24fps clips works fine on the timeline. But the one that still has 50fps will go black in the program monitor when I try to edit them on the timeline.
    It doesnt matter what I do, ripple edit or just shorten, still gets black. If I drag the marker over tha clips it shows fine though, but when editingt hem, just black.
    2.
    The second problem is regarding the very last clip in the timeline.
    The last frame, orjust some visual error after the last frame, now has the right part of the program monitor screwed up. A part of the screen is black.
    All this started like 2 days ago, after I upgraded my 2xSingle license to full CC. I had PS and PPro before.
    Whats going on?
    Some facts:
    - Premiere Pro CC 7.1.0 (141) - All updated
    - Win 7 64bit (all updated as of 2013-11-30)
    - 64 GB ram
    - Clips from Canon 5D MK3, 720, 50fps, IPS codec
    - No other software running, restarted several times
    - Geforce 480GTX, Asus P9X79, Intel Core i7 3820 3.6 GHz, Corsair 32GB (4x8192MB) CL10 1866Mhz
    - GeForce Drivers 331.82
    - Never had this problem before
    - Mercury Playback Engine GPU Enabled (disabled doesnt solve the problem)
    Please Advice
    // Magnus Svensson
    2 screenshots

    As I wrote, " I can drag the ends of the in/out points, BUT I cant drag the selected area in the source monitor"
    Again, the source monitor was just a comparrison, to show that this wasnt a problem only with the program monitor. I posted the image since you didnt understand what I meant.
    There are apparent issues with inserting theese clips on the timeline or editing them. I'm sorry if my bad english messes this up
    I guess you'll have to include all the info I have written to get a grip of the situation, so I will try to clarify again for you, if you think it will help
    - The project I have is sett to 720, 24 fps.
    - The clips I use are from 5D MK3, shot in 720, 50fps.
    - Some of the clips I interpreted to 24fps for a slomo effect.
    - I have QT installed
    - All drivers updated
    - The interpreted 24fps clips works fine on the timeline.
    - But the one that still has 50fps will go black in the program monitor when I try to edit them on the timeline.
    - It doesnt matter what I do, ripple edit or just shortens/makes longer, it still gets black.
    - If I just drag the marker over the clips in the timeline it looks fine.
    - If I interpret to 1-48fps, it works fine. Only 49-50 fps screws it up
    - Some problems occur in the source monitor. I CANT drag the full grey selection with the handle in the middle I made with in/out points, as shown in the picture
    - I tried to make a new project, same problems.
    - Everything worked fine a cople of days ago
    I hope this makes it easier to locate the issue.
    Thanks

  • Second monitor only shows when I  open PPRO a second time.

    CS5 WIN7 - 64 Pro
    Looking for a suggestion /solution  to an issue I have had for some while.
    I have the latest Nvidia Drivers for QuadroFX3800 but the issue began at least two previous versions ago.
    I open PPRO and it does not see the second monitor. It is not an option in the Playback settings.  (Not even there / Not greyed out)
    In fact it shows an image briefly (flashes on then off) on the second monitor  then turns it off (ie. the image going to it from the source monitor.)
    I shut out of PPRO and re open it almost immediately.  Bingo.  2nd monitor shows and its is also an option in the PB menu.

    I think I'm right in sayng that Mosaic has been added to the latest driver, 267.05 - the ability to stretch the desktop across 2 monitors.  I haven't been aware of it before.
    I say that because, having toyed with Mosiac,  I noticed that PP CS5 did flicker a few times upon boot in a way that it didn't on earlier nVidia releases.
    It seems to have settled down now.
    Am I not right in thinking, shoternz, that you are using the 2nd monitor as your preview, rather than program monitor?  Maybe there's a corrolation.
    Get your BM Intensity Pro out of the cupboard!

  • Monitor goes crazy when I adjust the angle...

    When I tilt my monitor back away from me, at a certain point the picture scrambles or sometimes the screen goes white until I tilt the monitor closer towards me. Sometimes it takes a couple of seconds to get the picture back, but it always has come back thus far.
    I assume a cable on the inside is getting pinched. Is there an inexpensive way to fix this or am I looking at a major repair???
    iBook G4 800   Mac OS X (10.4.6)   640 MB RAM, Combo
    iBook G4 800   Mac OS X (10.4.6)   640 MB RAM, Combo

    Hi Avidediter,
    Welcome to Apple Discussions
    I believe that you are having a problem with your reed switch, which usually cause symptoms that you are experiencing. You should bring it to your local Apple Store/Reseller to get it looked at and fixed. Did you purchase AppleCare?
    Jon
    Macbook 2.0 White (100Gb HD 2Gb RAM) Mac Mini 1.42Ghz, iPod (All), Airport (Graphite & Express), G4 1.33Ghz iBook, G4 iMac 1Ghz, G3 500Mhz, iBook iMac 233Mhz, eMate, Power Mac 5400 LC, PowerBook 540c, Macintosh 128K, Apple //e, Apple //, and some more...  Mac OS X (10.4.5) Moto Razr, iLife '06, SmartDisk 160Gb, Apple BT Mouse, Sight..

  • External monitor goes black when macbook pro has magsafe connected

    Hi,
    I have bought an external monitor about 1 week ago, and I have it connected with a minidisplay to dvi cable, and a dvi cable to the monitor.
    It was working OK -well, it had some sudden flash to black screen that lasted about 1 second, but nothing else- until thir morning when it just started showing a black screen. Mac OS sees the monitor, and I can move windows over there, etc. It's "alive". But I only see a black screen on the monitor.
    I tested with other computer, and it works OK. The cables work too.
    What I discovered is that if I unplug the power adaptor from the MBP the monitor screen shows correctly.
    It works OK only if the magsafe adaptor is unplugged from the MBP, it doesn't care if the magsafe adaptor is plugged to the power or not; only if it's connected to the mac book pro.
    It seems like some magnet stuff is making a mess there. What could it be? I can't work on the monitor only in battery power...
    I tried resetting nvram and the other stuffs that I found here, but nothing works.
    Thanks!
    Javyer

    Hi javyer!
    Here is an article that explains the troubleshooting for this issue in more detail:
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/ht1573
    Thanks for being a part of the Apple Support Communities!
    Cheers,
    Braden

  • Second monitor goes "blank" when first monitor goes full screen in Mtn Lion.

    Hello Apple community. I am using two monitors and when I put a program like iTunes in fullscreen mode (with the arrow symbol in top right) the second monitor displays that grey patchwork and I can't move windows over there.
    My question: Is there any setting to change this (so I could have one screen in fullscreen mode and the other screen on the desktop) or is this just the way it is?
    Any info would much appreciated!
    Thanks
    -MP

    mizatt wrote:
    My question: Is there any setting to change this (so I could have one screen in fullscreen mode and the other screen on the desktop) or is this just the way it is?
    It's just the way it is.
    BetterTouchTool (free app, in the app store) has a little feature that resizes your windows to full size when you drag them near the top edge and returns them to the previous size when you drag them down again. I find this useful when using two monitors (saves you having to resize them manually).

  • Screen goes blank when I open iTunes

    WWhen I open iTunes the screen goes blank (white ) freezes up,

    Hello m0r5o1t5s,
    The following article provides infomation and steps that can help stabilize iTunes.
    iTunes for Windows Vista or Windows 7: Troubleshooting unexpected quits, freezes, or launch issues
    http://support.apple.com/kb/TS1717
    Cheers,
    Allen

  • Preview monitor goes BLACK when I pause.

    I'm using a 15" Macbook Retina with the Nvidia 650M GPU, and up until the 2014 version of CC was released I could use the CUDA acceleration. Now, I cannot use it without the video going black the second I pause. Help is appreciated.

    Tyler,
    Try the following:
    Sign out from Creative Cloud, restart Premiere Pro, then sign in
    Trash preferences
    Ensure Adobe preference files are set to read/write
    Delete media cache
    Remove plug-ins
    Repair permissions
    In Sequence Settings > Video Previews, change the codec to one that matches your footage
    Create a new user account with Admin privileges and launch Premiere Pro from there.
    Disconnect any third party hardware
    Reboot
    Report back if anything here worked for you.
    Thanks,
    Kevin

  • N95 screen goes black when in between open and clo...

    Just noticed today that the screen goes black when sliding open or closed. Screen comes back on when slider reaches open or closed. Is this like the blank screen fault that affected so many N80s ? I'm very disgusted that I have to pay to fix my 16month old (expensive) N95 for an ongoing issue with Nokia sliders that they HAVE NOT fixed in their design. Very poor support Nokia. 
    Nokia 808
    Nokia CK-200

    Scott your grieviences are justified... but there is always a solution to a problem...even if this is a strange problem to be handled in an off the routine way, be it so... once again best of luck! not blame nokia for anything...nokia rules as always and nokia's productions have become very slow now :-( i wish they could make trendy phones like sony, sleek and stylish with new features.in some ways, nokia gets a little boring with no new features.. i dont feel any differnce between the nokia n95 8gb, n96 and n85(which i currently own)!
    Scott lets hope for the best :-)
    What's Worth Doing, Is Worth Doing Well!
    All "N-series" are incredible!

  • Why are the color images turning gray when I open them in Photoshop cs5

    My images are going gray when I open them so is there any on knows how to solve this issue

    what images
    if RGB, that sounds like a bad monitor profile or Photoshop setting

  • When i open a single word or excel doc, it opens all doc

    Hello all,
         Today i transfered my important documents from PC wirelessly to my mac at home. I was able to connect to my PC wirelessly using my MBP and copy all important doc to my mac so that i can access them on my MBP. When i open a single word file from document folder, for some reason it opens all of my word docs within my document folder. The same goes for when i open a single Excel file, it opens all of the excel files within my document folder. Can anyone help me figure out how to stop this?
    Thank you much for your help

    when you issue the Open command on  a Mac, it will open ALL the documents you have selected (highlighted) even if they are different kinds and need different Applications.
    Did you have multiple documents selected when you said Open or double clicked on one with many selected?

Maybe you are looking for