Monitor goes dark during gray screen after power outtage

The mini was plugged into a surge protector, but after the power went out, it doesn't get past the gray screen with the swirling disk, then goes black with an out of range message. I took it to the Mac genius today, he diagnosed it with an external drive, did repairs and got it to boot on his monitor. I have been reading the discussion and reset PRAM, unplugged everything, restarted holding the power button and plug at same time, done option start with CD, done a hardware check. Used Disk Utility to do an expended check, repaired everything. The monitor works fine with my G3. Still no screen. Any other ideas?
Mac Mini 1.25 GHZ, View Sonic Va2012 widescreen display. System 10.3.7 (reinstalled).

Well if it worked before and doesn't now, I would try trashing the preference files associated with the display. Use Spotlight and search on the term "windowserver". You should find at least two files with windowserver in the name that end with .plist. One will be com.apple.windowserver.plist and possibly com.apple.widowserver.xxxxxxx.plist where xxxxxxx will be a string of digits and numbers. Throw all such files in the trash, empty the trash and then restart. This should give you a fresh start with the mini and the Viewsonic.

Similar Messages

My Lumia Icon goes dark during calls and I cannot access the phone pad to unless I hit the power button.

My Lumia Icon goes dark during calls and I cannot access the phone pad to unless I hit the power button. Because of this it makes it tough to put my phone on speaker or type in my v-mail password.

I've been trying to find a common denominator. It happens inconsistently. It never happened before the Denim update. When it does occur, the screen goes black immediately upon answering the call and doesn't come back until the call is ended by the calling party.
I thought it might be the proximity sensor, but when it's working normally I can see the screen go dark when it's at my ear and comes back when I take it away (tried it multiple times). I had Gestures Beta installed. I wondered if that could have an affect so I uninstalled it, but that didn't make any difference. I'm still stumped by the inconsistency. I haven't reset my phone as I didn't really want to go through that...

TS1587 How can I get my Mac to run properly when it starts up and goes into a Gray Screen?

To cut a long story short here's basically what happened:
Had problems with signing into my Mac, not quite sure what happened. So after a lot playing around with some stuff, I tried to run a Start Up disk, which is now stuck in my Mac and it just goes to a GRAY screen everytime I go to power up my Mac. Have tried all sorts to get it going, but to know avail. There's not even a start up Chime. HELP PLEASE Thanks in advance.

No startup chime is usually the sign of a hardware failure. If you have an installer disc (or if the disc that's stuck in the optical drive is an installer disc) then you need to try booting from it. But the first thing you need to do is:
Intel-based Macs: Resetting the System Management Controller (SMC)
Resetting your Mac's PRAM and NVRAM
Next:
Booting From An OS X Installer Disc
1. Insert OS X Installer Disc into the optical drive.
2. Restart the computer.
3. Immediately after the chime press and hold down the "C" key.
4. Release the key when the spinning gear below the dark gray Apple logo appears.
5. Wait for installer to finish loading.
Repair the Hard Drive and Permissions
After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
If you can get this far, then you may be able to reinstall OS X without erasing the drive. But you will need to tell us what version of OS X you are using.

Computer turns on and goes straight to gray screen telling me to restart.

I just finished installing Leopard on my computer and I decided to do a software update. While the computer was restarting it stayed at a blue screen for a while downloading files. This was taking too long and I had a paper to do so I manually shut down the computer. Now whenever I turn my computer on it goes to a gray screen and tells me I need to restart.
If anyone could help I'd really appreciate it

Will it boot in Safe Mode? See
What is Safe Boot, Safe Mode? (Mac OS X)
http://docs.info.apple.com/article.html?artnum=107392
Resolve startup issues and perform disk maintenance with Disk Utility and fsck
http://docs.info.apple.com/article.html?artnum=106214
Will your Mac boot using the Leopard install DVD? If so, you probably need to do a reinstall of Leopard. When you reinstall the OS, do it via Archive & Install. See About the Archive and Install feature http://support.apple.com/kb/HT1710
Be sure to select Preserve Users & Settings. Also, repair permissions before and after the install.
A couple of Tips.
1. Before you install an update, ALWAYS repair permissions using Disk Utility. (Did you do this?) Then after the update is installed, repair permissions again.
2. I only use the Software Update window to determine what System related software is available for update. I don't use the auto update feature because there could be the possibility of a data "glitch" during download, which results in system startup/operational problems. Then I go to Apple site & download the update file. Then I install it.
For an update to an application, like iTunes, I use the auto update. If there is a problem with the update, you can reinstall the application, but it doesn't cause startup problems.
 Cheers, Tom

Gray screen after loading Yosemite

Hi. Have problem with Yosemite after 10.10.2 update from appstore. My MacBook restart and on 30-50% l see gray screen and no more, it's freeze after login or before. I can't go to recovery mode, can't install/ reinstall Yosemite.
On cmd+r - didn't see anything, just load
on shift - the same
on alt+cmd+r+p - restart and again great freeze screen
on alt - I see my hdd and ssd, if I input usb with Yosemite , I see this usb, no more.
On click on usb with Yosemite I see loading and gray screen after all of this..
If I inset second monitor, on MacBook freeze I see vertical lines. Red-green-blue-white vertical lines on all monitor
Please help me. I need work...

Install Mavericks, Lion/Mountain Lion Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer.

Can't get past gray screen after Boot Camp Assistant

So last night I decided it was time to start experimenting with Boot Camp and Windows XP Pro. I fired up Boot Camp Assistant and allocated a 32gb partition of my HD for the XP install. When prompted, I put in the XP Pro CD and restarted. It booted into the XP install utility, but when asking about which partition to use, instead of the 32gb partition, all I saw was a 131gb partition. Thinking that it was my OS X partition, I decided to cancel out of the install and do some more investigating. When it restarted, all I got was a blank gray screen, no spinning gear, no logos, nothing. When rebooting while holding down a mouse button, I was able to eject the Windows XP cd. Here's what I've tried so far:
CDs: Leopard, Original OS X Disk 1, Windows XP, None
Keys: none
Result: Gray screen
Keys: option
Result: Gray screen with mouse pointer that initially is moveable, but then freezes
Keys: c
Result: Gray screen
Keys: d
Result: Gray Screen
Keys: shift
Result: Gray Screen
Keys: command + r + p
Result: Gray Screen
Holding power button
Result: Long tone while starting up, then gray screen.
What can I do?? I'm thinking that Boot Camp fried my HD partition data, but I can't seem to access any of the boot disks or any sort of disk utilities

I did. I took it into the Apple store and they replaced my hard drive. It was under warranty, so it wasn't a problem. I got them to give me my old hard drive back, which I hooked up to an external SATA enclosure. My mac recognized it, but said it wasn't initialized. I downloaded Data Rescue II and it recovered all of my software. I'm now using it as a Time Machine disk.
After further research, I found out the my main problem was that I used Windows XP SP1. You NEED to use SP2, otherwise, this problem will occur. I figured I could just upgrade later, but nope, you need a native SP2 disk.
If your Mac isn't under warranty, try this post:
http://phail.net/2008/04/10/bootcamp-windows-xp-sp1-epic-phail/
and his solution:
http://phail.net/2008/04/13/bootcampsp1-white-screen-of-death-a-solution/
In short, you need another Leopard computer. I bet if you print out the instructions and take them to the Apple store with you, the Genius Bar will help you, they've always been super helpful/nice with me.
Good luck!!

This morning my PB G4 would not get to the password screen after power on. I have rebooted many times and very loud noises (like a HD spinning/rubbing) emits. Tried the Install disk and it cannot find the hard drive. Ran HW test and got a "Mass storage E

this morning my PB G4 would not get to the password screen after power on. I have rebooted many times and very loud noises (like a HD spinning/rubbing) emits. Tried the Install disk and it cannot find the hard drive. Ran HW test and got a "Mass storage Error Code" message.
Did my HD just crash and unrecoverable? Time to replace my notebook?

I believe your hard drive has failed. Hope you have a backup.
Failing Hard Drive Sounds http://datacent.com/hard_drive_sounds.php
Listed by drive manufacturer. Click on the > next to the drive & you will hear the typical failure sound.
How to Tell When Your Hard Drive is Going to Fail
http://www.lifehack.org/articles/technology/how-to-tell-when-your-hard-drive-is- going-to-fail.html
Grinding And Clicking – Symptoms Of A Failing Hard Drive
http://pcperformancetools.com/getdata/grinding-and-clicking-symptoms-of-failing- hard-drive.html
Failing Hard Drives
http://losangelescomputerhelp.com/computer_networking_news/failing-hard-drives.h tml
 Cheers, Tom

My macbook pro only goes to a gray screen with a blinking ?

when i turn on my macbook pro it goes right to a gray screen after about a minute a file folder comes up whit a ? in it

There are four general causes of this issue:
1. The computer's PRAM no longer contains a valid startup disk setting when there aren't any problems with the disk itself. This can be checked for by pressing the Option key and seeing if the drive appears.
2. The internal drive's directory structure has become damaged. This requires usage of an alternate bootable system to perform the repair.
3. Critical system files have been deleted. This requires usage of an alternate bootable system to reinstall them.
4. The internal drive has died or become unplugged. This is the most likely case if the computer took a sharp impact or there are unusual sounds coming from the hard drive's location.
(82990)

My Macbook will not boot the operating system. It just goes to a blue screen after the apple logo and the spinning wheel goes off. I took the battery out and held the on/off button for five seconds and reset the PRAM. I have the old mac os disk.

My macbook will not boot. It goes to a blue screen after the logo and wheel goes off. I have taken the battery out and held the on/off button for five seconds and reset the PRAM. I have the the original os disk but have not put it in for fear of losing un backed op data.
Thanks
Rich

You won't lose any data unless you erase your hard drive.
Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c"key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it.When it comes up is your Hard Drive in the list on the left?
If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've selected the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.

My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg():Socket is not connected

My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg(): Socket is not connected

If running 10.7 or later hold down Command-R at Startup.
This should invoke recovery Mode.
Choose Disk Utility.
Select your Hard drive. Inspect the SMART Status in the lower right of the window for "Verified".
Select the Mac OS X Volume (originally Macintosh HD) click (Repair Disk)
If errors, run again until it comes clean or gets stuck.
Report any error messages.

Gray screen after login - Cinnamon 2.2/Nvidia 334

I did a -Syu, saw the new Cinnamon. I then proceeded to snapshot my btrfs root vol, and went ahead with the upgrade. Rebooted, no desktop, just a gray screen with the pointer. I then booted off my install media, and mv'ed my snapshot back to replace my /
Unfortunately, that still somehow didn't fix it, which makes me think a conf is borked in my home dir (not in the snapshot). Nothing in the system journal.
Any ideas?

So, I added the following to pacman.conf -
IgnorePkg = cinnamon* muffin* nemo*
and this is the list of packages I allowed to upgrade -
:: Synchronizing package databases...
core is up to date
extra is up to date
community is up to date
multilib is up to date
infinality-bundle is up to date
infinality-bundle-multilib is up to date
Foreign packages: / 29 / 29
==> Package upgrade only (new release):
core/libsystemd 212-2 2 -> 3
core/systemd 212-2 2 -> 3
core/logrotate 3.8.7-1 1 -> 3
core/mlocate 0.26-1 1 -> 3
core/shadow 4.1.5.1-7 7 -> 9
core/systemd-sysvcompat 212-2 2 -> 3
extra/mesa 10.1.0-4 4 -> 5
extra/pango 1.36.3-1 1 -> 2
extra/clutter-gst 2.0.10-1 1 -> 2
extra/gthumb 3.2.7-1 1 -> 2
extra/libreoffice-en-US 4.2.3-1 1 -> 2
extra/libreoffice-common 4.2.3-1 1 -> 2
extra/libreoffice-base 4.2.3-1 1 -> 2
extra/libreoffice-calc 4.2.3-1 1 -> 2
extra/libreoffice-draw 4.2.3-1 1 -> 2
extra/libreoffice-gnome 4.2.3-1 1 -> 2
extra/libreoffice-impress 4.2.3-1 1 -> 2
extra/libreoffice-math 4.2.3-1 1 -> 2
extra/libreoffice-writer 4.2.3-1 1 -> 2
extra/pkgstats 2.3-3 3 -> 5
extra/polkit 0.112-1 1 -> 2
==> Software upgrade (new version) :
core/glib2 2.38.2-1 -> 2.40.0-1
core/device-mapper 2.02.105-2 -> 2.02.106-1
core/iproute2 3.12.0-1 -> 3.14.0-1
core/linux 3.14-4 -> 3.14.1-1
core/lvm2 2.02.105-2 -> 2.02.106-1
core/man-db 2.6.6-1 -> 2.6.7.1-1
extra/at-spi2-core 2.10.2-1 -> 2.12.0-1
extra/atk 2.10.0-1 -> 2.12.0-1
extra/at-spi2-atk 2.10.2-1 -> 2.12.0-1
extra/gobject-introspection 1.38.0-1 -> 1.40.0-1
extra/gdk-pixbuf2 2.30.6-1 -> 2.30.7-1
extra/cogl 1.16.2-1 -> 1.18.0-1
extra/json-glib 0.16.2-1 -> 1.0.0-1
extra/clutter 1.16.4-3 -> 1.18.0-1
extra/gtk-update-icon-cache 2.24.22-1 -> 2.24.23-1
extra/libcups 1.7.1-4 -> 1.7.2-1
extra/gtk3 3.10.7-1 -> 3.12.1-1
extra/clutter-gtk 1.4.4-4 -> 1.5.2-1
extra/cups 1.7.1-4 -> 1.7.2-1
extra/dconf 0.18.0-1 -> 0.20.0-1
extra/gnome-icon-theme-symbolic 3.10.1-1 -> 3.12.0-1
extra/gnome-icon-theme 3.10.0-1 -> 3.12.0-1
extra/libsecret 0.16-2 -> 0.18-1
extra/gsettings-desktop-schemas 3.10.1-1 -> 3.12.0-1
extra/evince 3.10.3-1 -> 3.12.1-1
extra/file-roller 3.10.2.1-1 -> 3.12.1-1
extra/fontsproto 2.1.2-1 -> 2.1.3-1
extra/gcr 3.10.1-3 -> 3.12.0-1
extra/gtksourceview3 3.10.2-1 -> 3.12.1-1
extra/libpeas 1.9.0-2 -> 1.10.0-1
extra/pygobject-devel 3.10.2-2 -> 3.12.0-1
extra/python-gobject 3.10.2-2 -> 3.12.0-1
extra/gedit 3.10.4-2 -> 3.12.1-1
extra/gnutls 3.2.13-1 -> 3.3.0-1
extra/glib-networking 2.38.2-1 -> 2.40.1-1
extra/gnome-common 3.10.0-1 -> 3.12.0-1
extra/gnome-keyring 3.10.1-2 -> 3.12.0-1
extra/gnome-screenshot 3.10.1-1 -> 3.12.0-1
extra/gnome-themes-standard 3.10.0-1 -> 3.12.0-1
extra/libsoup 2.44.2-1 -> 2.46.0-1
extra/xorg-server-common 1.15.0-5 -> 1.15.1-1
extra/xorg-server 1.15.0-5 -> 1.15.1-1
extra/nvidia-utils 334.21-7 -> 337.12-1
extra/nvidia-libgl 334.21-7 -> 337.12-1
extra/webkitgtk 2.2.5-2 -> 2.4.0-1
extra/gtk2 2.24.22-1 -> 2.24.23-1
extra/gucharmap 3.10.1-1 -> 3.12.0-1
extra/gvfs 1.18.3-3 -> 1.20.1-2
extra/libplist 1.10-1 -> 1.11-1
extra/libimobiledevice 1.1.5-2 -> 1.1.6-1
extra/gvfs-afc 1.18.3-3 -> 1.20.1-2
extra/gvfs-mtp 1.18.3-3 -> 1.20.1-2
extra/gvfs-smb 1.18.3-3 -> 1.20.1-2
extra/lcms2 2.5-2 -> 2.6-1
extra/imagemagick 6.8.8.9-1 -> 6.8.9.0-1
extra/js 17.0.0-1 -> 24.2.0-1
extra/libgee 0.12.0-1 -> 0.14.0-1
extra/libgnome-keyring 3.10.1-2 -> 3.12.0-1
extra/libtracker-sparql 0.16.4-1 -> 1.0.0-2
extra/nvidia 334.21-4 -> 337.12-1
extra/python2-gobject 3.10.2-2 -> 3.12.0-1
extra/python2-atspi 2.10.0-2 -> 2.12.0-1
extra/upower 0.9.23-2 -> 0.99.0-2
extra/usbmuxd 1.0.8-2 -> 1.0.9-1
extra/vte-common 0.34.9-1 -> 0.36.0-1
extra/vte3 0.34.9-1 -> 0.36.0-1
extra/webkitgtk2 2.2.5-2 -> 2.4.0-1
extra/xproto 7.0.25-1 -> 7.0.26-1
community/cjs 2.0.0-1 -> 2.2.0-1
community/python2-pillow 2.3.1-2 -> 2.4.0-1
multilib/lib32-pcre 8.34-1 -> 8.35-1
multilib/lib32-glib2 2.38.2-1 -> 2.40.0-1
multilib/lib32-nvidia-utils 334.21-5 -> 337.12-1
multilib/lib32-nvidia-libgl 334.21-5 -> 337.12-1
aur/jdk7 7.51-2 -> 7.55-1
==> New package :
extra/libinput 0.1.0-1 (required by clutter)
extra/libusbmuxd 1.0.9-1 (required by libimobiledevice)
extra/js17 17.0.0-1 (required by polkit)
and I still had the same issue with the gray screen after login.
Last edited by madscience (2014-04-16 15:02:33)

Beach Ball of Death, Dark Gray Screen after Clean OS ReInstall- Please Help

My 13" MBP is less than two months old.
I read online somewhere that a company that buys large quantities of Macs has a strategy for combating the industry standard 5% hard drive failure in new notebooks. It said something along the lines of performing a clean install / reformat of OS X was a good idea to see if any problems arise- then the HD would likely have problems in the near future, etc...
Being the nerd that I am I performed a clean install on my MBP. I had just performed one the day before on my other Mac (which worked perfectly).
First of all, my MBP took roughly 15 minutes to boot from the disk (to begin the reinstall). Actually one time I gave it over 20 minutes and it never did load. Once I finally got to the Language select screen it froze, clicking the continue arrow did nothing and I couldn't even choose another language. So I shut down and tried again. The DVD doesn't look scratched. Is my drive less than stellar?
This time, it worked, albeit, it took much longer to install than my lesser powered Mac Mini. OS X notified me that the installation was successful and that it now simply needed to restart. Upon restart I was greeted with a dark gray screen and mouse cursor spinning beach ball (that responded to trackpad).
Shut down, turned it back on- same thing. Tried a bunch more times, no luck.
Called Apple Care and after a few questions / tips we concluded that it needed to be sent in, the associate imagined it was a HD problem.
I took my MBP to a local authorized service provider and they took it, and called me back in a few hours. I asked what they did to fix it, and they skillfully dodged the question. They said it should be good now, that it passed all hardware tests, but to let them know if it happened again.
Since then it's been running okay. As a nerd it's a bit bothersome to know that I can't perform a clean install when I see fit- and that if I did, I'd have to take it into Apple Care again in the future, and once Apple Care runs out than a clean install just isn't an option.
It boots up just as fast, but when it gets passed the white screen with the Apple logo... when the desktop is loading I noticed that it stays at the flash of the solid blue desktop a bit longer than usual (the second before it loads your desktop bg image). It also seems that fully loading all of the top right menu bar items takes a bit longer than before.
Also, not sure if the hard drive's sudden motion sensor is going haywire. But randomly, the hard drive will make a singular faint "thud / click" noise. Very faint. But it's not your usual "reading data from the HD" hard drive thrashing noise you hear when you open an app / file. It's a single, more sudden noise, but like I said it is fairly quiet- I hear it when I have literally nothing running except this Safari window. This is something I didn't notice the first few weeks with the MBP.
Also in system profiler, the battery's condition was never good, but only "Normal." I did calibrate my battery one of the first days I had it.
Here's some coconutBattery info:
Current Battery Capacity: 5588 mAh
Original Battery Capacity: 5770 mAh
Which is 96%.
Load cycles: 10
Anyways, curious if anyone has any ideas about my inability to perform a clean install and successfully boot up? I don't see any reason why it should have taken THAT long to boot from the disk, frozen in several random spots throughout, and then not be able to boot up.
The HD noises aren't a huge deal just a bit concerning, and admittedly the battery info is just nerdy paranoia. Just curious what's going on with my MBP. Is there anything I can do, or should read?

Hi simplecoder13,
I perform a similar process on all the HDs that I buy, only I take it a step further. I'll run a single pass erase on drives under 500GB and a seven pass erase on drives larger than 500GB and ones that are deemed "mission critical." Here's an interest metric, though.
Since 01/01/10 on laptop drives (Seagate, Western Digital, Hitachi)
+HDs purchases - 461+
+Drives > 500GB - 119+
+Drives < 500GB - 342+
+Drives that fail zero test - 13+
+Drives that pass zero test, fail within 30 days - 2+
+Drives that pass zero test, fail within 60 days - 0+
+Drives that pass zero test, fail within 90 days - 3+
+Drives that pass zero test, fail within 180 days - 4+
+Total drive failures within 6 months - 22 (4.77%) ~ 5%+
I don't have a manufacturer break down, I suppose I should start logging that more closely. Anyway...
I have a new MacBook Pro (13" @ 2.4GHz) and booting off the installation disc, from selecting the installer disc via the boot manager to the language selection screen is ~ 6 mins and 44 seconds. I use that as an average, I did it over 10 restarts but it was a pretty fair assessment. The fact that the installer is freezing is definitely cause for alarm, that's not normal or to be expected. Process of elimination would tell me the following:
1.) The disc is bad
2.) The optical drive is bad
My understanding of the installer is the HD isn't initially accessed during the installer until you choose an install location (at which point it's mount point is verified).
Regarding the battery, your full charge capacity is going to bounce around the first couple of months, usually anywhere from 250-400 mAh. I noticed sporadic reporting until I reached the 50 cycle mark (or around 6 months based on usage). That being said, I don't see any problems or cause for alarm with the information you've reported.

Screen goes dark during playback

When playing a DVD through Front Row the screen is going dark as it does when it is not touched for a while to save battery. However it does not do it all the time and does it at random intervals. Any ideas??
I have played around with energy saving settings but nothing seems to be quite hitting the nail on the head.
MacBook Mac OS X (10.4.6)

Try it in DVD Player (found in the Applications Folder). It may or may not do it here.
The problem may very well be the settings for power consumption.
1. Open system prefs (Apple Menu > System Prefs)
2. Click Energy Saver
3. Make sure that under "settings for:" you have battery selected (you may want to do this for both battery & Power Adapter)
4. Where it says "Put the display to sleep when the computer is inactive for:", choose 3 hours
5. Click options
6. Uncheck the box labeled "Reduce the brightness of the built-in display when using this power source"
This should do the trick. Again, you may want to do the same for the power adapter settings, if this is also happens using the power plug.
Hope this is helpful,
Cory

Screen Goes Dark During iPhone Sync

This sounds strange and I can't seem to find a logical explanation for this. I noticed that I went I plug my iPhone via USB for iTunes to automatically synch, within seconds the screen goes dark. What I have been doing lately is to rest the phone on top of the MacBook Pro, just left of the trackpad. I have also noticed that if I just place the iPhone elsewhere, rather than laying directly on the MacBook Pro, the problem doesn't happen.

That's where the magnetic sensor for the lid is located. It causes the computer to think that it is closed! Now, an iPhone doesn't have a magnet, except in the speaker, so maybe that's what happens. Our your case has a magnet.
I hope this answers your question.

Monitor goes dark on 2008 Mac Pro Tower with ATI Radeon 5870 Card

I have a 2008 Quad Core Intel Mac Pro Tower running 10.6.8.
The original graphics card had trouble with HD movies of any kind and eventually my screen would sometimes not turn on (stayed black) when the computer was turned on.
So I replaced the graphics card for both reasons to a ATI Radeon 5870 PCIe with a GB rather than the 256 that came with the machine.
The problem was solved. I got a new monitor, one that is like the latest ones and all has been working great for a few years.
Then recently the monitor started going dark while the computer was on. (no screen saver or anything like that, I can be in the middle of work on a photo or video).
Trouble shooting I have tried.
A forum said drag the mouse to the hot corner for a while and then back. Well, I tried, assuming I was dragging the mouse to the corner. Didn't work.
I tried using the keyboard commands to shut down the computer. It didn't work.
I tried plugging the keyboard into other USB ports and tried to shut down the computer. No luck.
The only thing that works is shutting down the computer with the power button.
on start up the monitor is back on.
Sometimes it works for days like this, other times the monitor stays on only minutes.
The monitor is fine. Tested my old monitor on the computer to make sure it wasn't my new monitor.
So the questions are:
Can it be over heating?
is it worn out, toast, done and or dead and dieing?
Should I buy a replacement graphics card VS finally upgrading and getting a new computer (lots of $$$$ but then I do work in HD Video so....)
any help is appreciated
thanks
john

Replacing FBDIMMs would be today inexpensive and worth doing.
No one knows if heat is an issue without your using thermal sensor monitor. Probably want to up the default fan speeds while at it.
And because you don't have Lion+ then even more reason to setup a small maintenace volume on another drive with OS X basic system for repairs. In fact you should always have a bootable backup or two you can rely on.
Restarting may work, or it may be you have now new issue with corrupt fies or directory that a safe boot even is no guarantee of fixing.
When in doubt, try a clean new OS install on another drive.
And FBDIMMs: $25 for a 2x2GB set on Amazon.com
You want to get the most out of what you have, a small investment in RAM, maybe recycle those drives for 2-4TB units. And an SSD will have system responding better and perform better.
My guess, the 5870 wasn't needed and was overkill and a 5770 for almost half would have been more than adequate.

Monitor goes dark during gray screen after power outtage

Similar Messages

Maybe you are looking for