***Monitor HTTP Adapter

Hi Experts,
Is there any tool to monitor the Sender/receiver HTTP Adapters?
Thanks,
Srinivasa

Srini,
Use -/people/stefan.grube/blog/2007/03/29/troubleshooting-soap-http-and-mail-adapter-scenarios-with-tcpgateway
Thanks!

Similar Messages

Monitoring http adapter

hi
if message is picked from source and not reached xi how we will monitor for http adapter.
regards
raghu

for HTTP adapter monitorig, there is no direct tcode......
you can go to SM59 to see whether the HTTP connections between XI and R/3 are up and running......if your HTTP connections are working here, then your HTTP adapter will be working.......then go to SXMB_MONI to see the xml msgs
Please check the blog on searching for messages with values in the payload using the TREX engine....The XI system has to be SP15 or above...
/people/prasad.illapani/blog/2005/11/14/payload-based-message-search-in-xi30-using-trex-engine

Http Adapter Problem

I am working on File to Http Scenario. I am sending one requist to Servlet. In runtime monitaring showing black flag. but request is not going to Servlet. How will i monitor Http Adapter.
Thanks

/people/stefan.grube/blog/2007/03/29/troubleshooting-soap-http-and-mail-adapter-scenarios-with-tcpgateway
Thanx
Aamir

HTTP Adapter installation

Hi,
I was trying some scenarion in HTTP Adapter and was not able to get message in Integration Server.
I found in RWB->Component Monitoring->Adapter Engine->Adapter Monitoring HTTP Adapter is not available. Is this means HTTP Adapter is not installed?
If it is not installed how to install it.
Please advice.
Thanks,
Sri.

Hi Keith,
The thread gives you an idea of testing your HTTP adapter.
HTTP Sender Adapter Strange Problem After SP16 Patch!!!
I think you have to check in SICF if service sap/xi/engine is on.
Regards
Vijaya

Busine Process Monitoring: define alert in XI for HTTP adapter

Hi Experts,
Iu2019m working with SAP XI 7.0 and solution manager 701. Iu2019m configuring BPM.
I want to monitor the error in XI. I have three systems:
Legacy System --> SAP PI --> ECC
The legacy System, communicate whit SAP PI with HTTP request so the adapter sender in PI is an HTTP Adapter.
I want to monitor the errors in the http adapter so I created the alert category HTTP_ERROR_ADAPTER in the abap stack (transaction alrtcatdef).
When I try to configure the alert in the Runtime WorkBanch I canu2019t find u201CHTTP Adapteru201D in the field u201CAdapter Engineu201D . I can see only jdbc, rfc, mail u2026. Adapters.
I think that I canu2019t see the http adapter because the HTTP Adapter is not a java adapter.
So, how can I monitor the errors in the HTTP adapter sender in SAP PI? Can I monitor the http adapter sender errors using the field u201CIntegration Engineu201D (u201Cerror categoryu201D = * and u201Cerror codeu201D = * )?
Thank you a lot in advance for collaboration.
Best regards
Giou2019

how can I monitor the errors in the HTTP adapter sender in SAP PI?
Alert category option you are trying won't work. The only thing you may check in PI perspective is whether http service is running in smicm. I am not sure but CCMS monitoring could take care of this specific category. Other way without thinking about alerts could be using manual TCPGateway procedure to trace http calls.
Can I monitor the http adapter sender errors using the field u201CIntegration Engineu201D (u201Cerror categoryu201D = * and u201Cerror codeu201D = * )?
Integration Engine category here won't be actually the http related error, it would be pipeline steps related error.
Regards,
Prateek

Plain Http adapter Monitoring with CCMS / Alerting framework

Hello all,
Can you explain me the optimal way to monitor process using plain http adapter (Sender AND Receiver).
My goal is to push issue information as soon as possible to monitoring team (via CCMS) when the process is in error.
During my tests, I ve had a lot of messages with ICM HTTP error 110 but Integration engine did not trigger any alert.
Thanks for your help.

Hi,
Check this link for ICF trace.
http://help.sap.com/saphelp_webas620/helpdata/en/2d/64d041e74911d6b2e400508b6b8a93/content.htm
/people/arulraja.ma/blog/2006/08/18/xi-reliable-messaging-150-eoio-in-abap-proxies
/people/michal.krawczyk2/blog/2005/05/10/xi-i-cannot-see-some-of-my-messages-in-the-sxmbmoni
regards
Aashish Sinha
PS : reward points if helpful

Monitoring HTTP receiver adapter ?

Hi Guys,
How to monitor the HTTP adapter ? How can we know when any errors in the HTTP adapter ? Do i need to look in the integration engine ?
Thanks,
srini

If there is an error in your reciever HTTP adapter you will find the red flag in XI itself in SXMB_MONI.
To monitor your Receiver HTTP adapter, you need to use the SXMb_MONI itself.
Regards
Bhavesh

UTF-8 encoding problem in HTTP adapter

Hi Guys,
I am facing problem in the UTF-8 multi-byte character conversion.
Problem:
I am posting data from SAP CRM to third party system using XI as middle ware. I am using HTTP adapter to communicate XI to third party system.
in HTTP configuration i have given XML code as UT-8 in the XI payload manipulation block.
I am trying to post Chines characters from SAP CRM to third party system. junk characters are going to third party system. my assumption is it is double encoding.
I have checked the Xml messages in the Message monitoring in XI, i can able to see the chines charaters in XML files. But in the third party system it is showing as junk characters.
Can you please any one help me regarding this issue.
Please let me know if you need more info.
Regards,
Srini

Srinivas
Can you please go through the SAP Notes 856597 Question No.3 which may resolve your issue? Also have you checked SAP Notes 761608,639882, 666574, 913116, 779981 which might help you.
---Satish

HTTP adapter - 500 Internal server error

Hi Experts,
I have configured a B2B scenarion in which i am using HTTP receiver adapter to send data to vendor.I have checked my configuration every thing is fine but i ended up with the error as below.
SXMB_MONI:
PLAINHTTP_ADAPTER">ATTRIBUTE_SERVER
HTTP server code 500 reason Internal Server Error explanation Internal Server Error
And the queue status is saying red in sxmb_moni also the error in SMQ2 is as follows
XI Error ATTRIBUTE_SERVER.PLAINHTTP_ADAPTER: Queue
I have implemented the notes 804124,807000 but no luck.Also i have restarted the J2EE server and done the soft shutdown but no use.
If i look into th queue scheduler in SMQR its in INACTIVE.
Any hint will be helpful.
Thank You

Hi
The Plain HTTP adapter is not part of the adapter framework, so you cannot see anything in the adapter monitor.
Log on to the server, where the XI is installed. Can you ping the receiver host? Can you put the URL of the receiver as browser address, does that work?
HTTP 500 can be any problem at receiver side. Are you sure, that the payload fits to the receiver requirements?
Please refer this thread answered by Stefan Grube
Plain HTTP adapter error
Thanks
Abhishek Mahajan
***Please reward points in case helpful***

Java HTTP adapter in PI 7.3?

Hi Experts,
Anyone adivse me how to implement the java HTTP to File scenario via PI?especially explain me the HTTP sender side and how to test as well.
thanks in advance.

HTTP adapter now comes in AAE in Pi 7.3. Except that there is no big difference between PI 7.3 and lower versions. You can go to component monitoring --> adapter engine --> test message and paste your payload and test. You are going to test in adapter engine level instead of abap stack (integration engine).

HTTP Adapter Receiver -- Message not arrive

Hello,
i send an IDoc from an SAP System to the PI and then with the HTTP Adapter
to a non SAP System.
The Message didn't arrive.
The Message Monitor says 'Call Adapter'.
Any Ideas?
Regards
Patrick

Patrick
A similar issue has been discussed here:
XI_J2EE_ADAPTER_XI_HANDLER - GENERAL_ERROR
Unfortuantely it is a gnereic error.
Try extending the trace file in the log configurator in Visual Admin to see if you can get a better indication of what is triggering the error.
Try running RSXMB_ACTIVATE_ICF_SERVICES in SE38 to see if this kicks off the Integration Engine services.
Also, check page 29 from this guide:
https://websmp102.sap-ag.de/~sapidb/011000358700001697502004E.PDF

Http adapter-sender side error in communication

Hi,
I have configured the sender http adapter in the test enviroment
and i did some test using a test tool
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/66dadc6e-0a01-0010-9ea9-bb6d8ca48cc8
The test was a success . I used a url:
http://sapxid:8000/sap/xi/adapter_plain?namespace=urn%3A/RepairJobCAp_SapInbound&interface=MI_RepairJobC&service=BS_CRM&party=&agency=&scheme=&QOS=EO&sap-user=xiappluser&sap-password=XIPASS&sap-client=001&sap-language=EN
When i did the test with the real tool of the sender system it failed , and the only sign was the log in window of the XI WAS with the user name of xiappluser .It seem that failed to log in , the password it is ok as it works with the test tool. Do you have an idea what it could be ?
Best Regards
Antonis

hey
could you please post the URL to which the actual sender system is pointing to(the URL to which it is sending the message to XI)
also use TCP gateway to monitor the sender HTTP
/people/stefan.grube/blog/2007/03/29/troubleshooting-soap-http-and-mail-adapter-scenarios-with-tcpgateway
Thanx
Aamir

Idoc and http adapter

Idoc and http adapter resides in ABAP stack. So how do we monitor these two adapters ? It wont be visible in RWB ?

Hi,
To know the difference i suggest u try to do it by ur self only.
Login in to Runtime Work bench- component monitoring-Adapter engine-communication channel monitoring- Filter the communication channel with name.
and click on message id of that channel, it will show u the steps by step log for that channel.
MONI is used for message monitoring.
chirag

Error while connecting to external server through SOAP/HTTP adapter

Hi,
we are trying to connect to the external server through SOAP adapter. The scenario is proxy to SOAP asynchronous scenario.
We are getting following error in Communication channel monitoring:
*Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException: SOAP: response message contains an error Application/UNKNOWN/APPLICATION_ERROR - application fault*
We also tried HTTP adapter in the receiver side. But it is giving red flag in SXMB_MONI with following error:
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIAdapter</SAP:Category>
<SAP:Code area="PLAINHTTP_ADAPTER">ATTRIBUTE_SERVER</SAP:Code>
<SAP:P1>500</SAP:P1>
<SAP:P2>Internal Server Error</SAP:P2>
<SAP:P3>Internal Server Error</SAP:P3>
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>HTTP server code 500 reason Internal Server Error explanation Internal Server Error</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
Please help.
Thanks in advance.
Regards,
sriparna

Make sure that the receiver webservice is up and running and in a state to receive the external calls. Confirm if the data you send is as per the requirement of the webservice and they haven't changed anything at their end.
Regards,
Prateek

HTTP adapter: where to see the transformed output message

All,
I am a beginner in Webservices/HTTP interfaces in PI. I have to make changes on an existing custom interface which uses HTTP adapter. I have done the changes in the message mapping and tested it using the test tool. It seems OK.
However when we do end-to-end testing, data is flowing but bussiness needs a copy of the transformed data that has been sent out from PI.
I checked RWB->Message Monitoring-> Integration server(Database) and it showed the successful message. When I drilled further into this message, it showed the SOAP message (Version 0 and Version 1 with payload). The payload showed the data that ECC had sent to PI and not the transformed data that went out from PI to 3rd party via HTTP adapter.
Appreciate if you could guide me in right direction regarding where to see the Output/Transformed data that is actually sent to third parties.
I have checked SXI_MONITOR as well in PI but that also shows the payload only and not the transformed data.
Regards
SK
Edited by: Shirin K on Feb 18, 2010 3:10 PM

Hi ,
Go to particular message in SXI_MONITOR. In Message there will be window on left hand side. There will be Technical Routing.
Technical Routing> Payloads->Maindocument. This shows the Output data.
If you are not able to see Technical Routing inform you basis team they need to do some configuration in SXMB_ADM
Edited by: Rajhans Abhay on Feb 18, 2010 4:29 PM

***Monitor HTTP Adapter

Similar Messages

Maybe you are looking for