Monitor Is Flickering - ATI Display Driver Problem Error Message

Hello, for the last few weeks, I have been having a monitor issue. Everytime I turn my computer and monitor on, it is flickering like crazy on my HP 2509B Desktop Monitor, and on the right bottom corner a flag shows up with ATI Display driver, and I am trying to figure out how to repair this monitor issue. I don't know if it is coming from the Monitor itself or its coming from the Mother Board TOWER, I am going crazy with this and its hurting my eyes everytime I turn it.
Sometimes the flickering would just go off by itself, and now its doing it constantly. I don't know what to do with this.
I love my monitor and I hate to see to replace it or something. Please help me with this. I hope it is not a driver hardware issue.
I would greatly appreciate all the help I can get to do this myself if not then I am going to have to take to the store I bought it from and get them to help me out, but I want to do this on my own. If you can help. Thanks

if you have another monitor you can test it to see if if does the same thing and also check the cable and maybe use a different one to see if the cable is not the cause which i doubt
Please provide Kudos to whom has provided answers or
good points or advice..
Aslo if the questions or issues solved please check it
"Accepted"
Thanks and you are welcome _____ Rick

Similar Messages

Satelite Pro A200 ATI display driver problem

Hello there,
Have following problem: Can't install ATI software on my notebook. There is an error message during installation: "Catalyst Install Manager can't initialize Detection Manager".
OS - Vista Business
Display adapter - Mobility Radeon HD2600
Any suggestions?

Hi
You could try to use another installation procedure;
- Unzip the ATI graphic card driver package
- access the device manager and choose the graphic card
- choose update the driver and point to the palace where the display driver package was unzipped.
This should help to renew and to reinstall the graphic driver.

[W500 and Windows 7] ati display driver stopped responding and has recovered

Hi,
I installed Windows 7 64bit on my W500 (almost 3 weeks old). It installed a driver for the ATI display card from Windows Update. However, since yesterday, I regularly get a driver crash (I assume...).
It's happening when I'm scrolling in a webpage, suddenly the page hangs, the mouse and Windows itself hangs seconds later and after that, after 5 seconds, my screen goes black, the machine beeps and it's back. In the tray, I get an error: ati display driver stopped responding and has recovered.
In the details of the driver, the following can be seen:
Driver Date: 28/04/2009
Driver Version: 8.612.0.0
The card is recognized as a 3650.
Am I doing something wrong here? Can I test with another driver (I tried installing the Windows Vista 64bit, but it doesn't seem to be willing to install...)?
Thanks in advance,
gill

I have the exact same hardware and software (Win7 64) and I'm getting precisely the same symptoms, screen blanks out when I am scrolling a web page vertically using the trackpoint and the center blue trackpoint scroll button.
It's really annoying.
It also never happens when the laptop is in the dock, or when the integrated graphics are engaged, this only happens when the ATI chip is running and only since ATI released the new Windows 7 drivers.
Previously I'd ran this box on on Win7 64 but used the Vista 64 bit graphics drivers from ATI and didn't have the problem, but installation was a pain.

Equium A300D - Toshiba ATI display driver upgrade is not working

Hi
Has anybody else found the Equium A300D PSAK2E Windows Vista 32 bit Toshiba ATI display driver download will not work from the download centre? If you choose run, the download causes the windows explorer to crash during the install and the upgrade fails, the same with save and the install does not self install.
I have been trying to get the TV out S-Video port working. See thread on TV out not working. I have tried everything. has anybody else got this problem as Toshiba are unaware of any problems with the S Video TV out not working on this machine.
Thanks Vince

Hi,
The down load downloads ok but when you try and unzip it, then install it halfay through you get an error message stating windows explorer has stopped working and it has crashed. The Graphic card then will not work. I have tried uninstalling all the ATI software and deleting the left over files but it still wont install.
I have downloaded the programme from the ATI site and this installed ok and the graphic card is working. The s video tv port still will not work.
I have gone into great detail on the post regarding the TV out not working about what i have done. When the s video lead is connected the computer can see the tv but will not output, when you try and enable the display the display will not enable. I have used the FN f5 key with no success, changed settings on the avi controller and display settings in the control panel
I will take the machine back to where i bought it from next week and see if they can get it to work!

ATI display driver fails to work with new kernel

Hi,
I've just upgraded from
OEL kernel-2.6.18-194.11.3.0.1.el5.x86_64
to most current
OEL kernel-2.6.18-194.11.4.0.1.el5.x86_64
and got the problem with ATI display driver. Whenever I perform kernel upgrade, I have to recompile vendor-provided ATI display driver downloadable from AMD/ATI site, because system ATI driver, provided by OEL/RHEL as kernel module, doesn't work properly (too slow). I did that hundred times and never had a problem. This time the problem is that after upgrading to new kernel and recompiling the existing ATI display driver (Revision 10.8), it doesn't work anymore, even though it worked perfectly with previous kernel. I cannot even start X11 (glibc problem reported with stack traces!!!). The newest ATI display driver (Revision 10.9) "works" with new kernel, but display is awfully slow making any serious work impossible. It is even slower than system-provided ATI driver.
I am pretty sure the problem is in new kernel. As I have no backup of old kernel files and couldn't download the previous OEL kernel files from ULN, neither binary nor source (the files do not exist on ULN anymore, only the recent kernel files), I downloaded the previous kernel source from ftp.redhat.com, compiled the kernel and downgraded to it, recompiled ATI display driver, and everything works properly and fast as before upgrading. I can remember that ULN site used to have all kernel versions prior to actual one and cannot understand why Oracle dropped this practice. As I have an ULN account, I certainly want to have OEL patched kernel.
My question is: does anybody know how and where I can download the previous OEL kernel-2.6.18-194.11.3.0.1.el5.x86_64 binary rpm files or at least source rpm file?
Maybe Sergio or Tommy can help?
Thanks in advance.
NJ

I have experienced the same with Ubuntu some years ago - specific feature (hack?) that was implemented in the kernel was deprecated. This was used by the display driver for an onboard Intel graphics chipset. Beryl (which was subsequently merged with Compiz) turned into a horribly slow experience. As far as I recall, a subsequent kernel patch "fixed" things as a number of users were affected, of which many complained very loudly.
Anyway, I think the lesson here is that OEL is not really the correct distro to use for a desktop. A broken ATI driver for the OEL kernel? Does not really feature in the scheme of things for OEL support. Oracle Grid/RAC/Enterprise/Standard Edition do not care. Oracle's application servers (Apache, Weblogic, etc) do not care. Etc.
Sure, GUI desktop access to an OEL server is needed (like when running dbca or an installer) - but that can easily and effectively be done using vncserver for example and running twm.
You may be able to fix/work-around the problem with the current kernel update.. you may be able to roll back the update. But what about the next time when some other component does not work after a patch or an update? Surely it is a lot less stressful and frustrating to rather use a desktop distro, like Ubuntu, instead?

Satellite Pro A60: ATI display driver keeps breaking down

I have had my Sat pro A60 Laptop for about a year now.
I have had a few problems with it since I got it but the main problem has just occured within the last 6-7 months.
The ATI display driver keeps on breaking down and in order for it to work I have to restart the system. This has been an ongoing problem for quite some time and it's now getting rather irriating. It does it at the most inconvenient times like when I am watching a DVD or listening to a CD.
Sometimes when I put the computer on standby, the display doesn't even start up again and the screen remains blank. In order to sort this out I have to switch off the laptop and then restart it. The main problem I have put this down to is overheating as it can get quite hot when I use it.
I sort of know how to sort this problem out, just by clearing dust from the fans. But if there is any other solution to this please help.
Thanks!

Hi
Mostly the overheating happens because of the dirt and dust inside of the cooling modules. The fans cannot work properly and cannot spin with full performance.
I think you should check the fans. I think the easiest way to clean the fans is to use the vacuum cleaner hose against the fan grilles.
About the display issue: In your case I would recommend firstly to update the display driver. Additional if the OS runs since a long time on the notebook so maybe a new OS installation form the Toshiba recovery CD would help.

ATI Display Driver

I am trying to install the the ATI Display Driver package for a T500 without any of the applications that are included with it. In other words, I only want to install the drivers and nothing else like the Catalyst Control Center, etc.
When I try to do a customized install, I cannot uncheck any of the boxes I don't want installed. It seems like it is all or nothing. what's customizable about that?
Is there a way to do what I want?
Thanks

You could ignore the fact that catalyst control center is installed and just remove CCC from startup (under HKLM\.....\Run in registry) when Windows is starting. Or you could uncompress the package and just install the driver by going into device manager and choose to update driver the driver then select the directory where you uncompressed the package.
-gan

Aperture crashes when doing enhancements crashed at thread 35 which i think is a display driver problem any ideas folks

Aperture keeps crashing every time I try and do some auto enhancements crash log comes up with crashed at thread 35 or 36 which seems to point to a display driver problem imac 2.16 intel core 2 duo 3gb ram os x 10.6.7.
This is making aperture unusable I might go back to lightroom never had these problems with it.
Graham

Hi yes I'm running 3.1.2 I have tried 32 bit mode and it does just the same.
Graham

I'm going nuts with display driver problems!!!!

Hi everyone,
I joined the forum some time ago but I can't get back in so I logged in with a new ID.(Pain)
I have a problem that I hope someone can help with When I place any of my work or a photo into CS5-Ext. I can't do any work on it? No matter what tool other than the paint brush I use, as soon as I click on the picture / work it disappears and will only re-appear if I click on it again. I've tried all sorts and it's driving me nuts, Can anyone help?---PLEASE---
Thanks.

That sounds like a display driver problem.
What OS are you running?
If Windows, you can often visit the web site of the maker of your video card and download/install an updated driver.
If OSX, you need to look to Apple and their OS updates to get updated display drivers.
-Noel

ATI display driver rollback

I have desktop running Enterprise Linux server 2.6.18-164. Recently I installed ATI display driver on it. After that I am not able to restart my machine. Is there any way to roll back the recent driver changes???

You can try to boot in text mode (no graphics) and check /etc/X11 directory. Usually, whenever a change in graphics settings occurs, the system makes a backup of the original configuration file (xorg.conf) and then applies the new settings. So, you can try to replace the current configuration file (xorg.conf) with the old one (xorg.conf.backup), if it exists...
kido

Ati Display Driver Issue

Every time I run Live Update 5, it states that the ATI display driver is NOT installed. Additionally, the video card doesnt show up in control center, cpu-z nor AMD Overdrive.
I have already removed all of the display drivers and reinstalled with no luck. Everything seems to be running fine, but its annoying me and I want it fixed. Stats Below:
CPU Arch : 1 CPU - 4 Cores - 4 Threads
CPU PSN : AMD Athlon II X4 645 Processor
CPU EXT : MMX(+), 3DNow!(+), SSE (1, 2, 3, 4A), x86-64, AMD-V
CPUID : F.5.3 / Extended : 10.5
CPU Cache : L1 : 4 x 64 / 4 x 64 KB - L2 : 4 x 512 KB
Core : Propus (45 nm) / Stepping : BL-C3
Freq : 3549.52 MHz (229 * 15.5)
MB Brand : MSI
MB Model : 870S-G46 (MS-7599)
NB : AMD 870 rev 00
SB : AMD SB850 rev 40
GPU Type : AMD Radeon HD 6670
DirectX Version : 11.0
RAM : 8192 MB DDR3 Dual Channel
RAM Speed : 610.7 MHz (3:8) @ 8-8-8-20
Slot 1 : 4096MB (10700)
Slot 1 Manufacturer : Corsair
Slot 2 : 4096MB (10700)
Slot 2 Manufacturer : Corsair
I have a feeling that it is something simple I am overlooking, but any help woudl be appreciated.

Thought this might help too:
GPU-Z Validation hraac
Card Name:
AMD Radeon HD 6670
Owrer:
Anonymous
Submitted:
2012-03-14 13:20:42
Owner's Comments:
GPU:
Turks
Revision:
Technology:
40 nm
Die Size:
118 mm²
BIOS Version:
013.012.000.031.000000 (113-667ZWF71-113-AD28900-X00-XF)
Device ID:
1002 - 6758
Bus Interface:
PCI-E 1.1 x16 @ x16 1.1
Subvendor:
XFX Pine Group (1682)
ROPs:
8
Shaders:
480 (DX 11.0)
Pixel Fillrate:
2.0 GPixel/s
Texture Fillrate:
6.0 GTexel/s
Memory Type:
GDDR5
Bus Width:
128 bit
Memory Size:
1024 MB
Bandwidth:
64.0 GB/s
Driver:
atiumdag 8.950.0.0 / Win7 64
GPU Clock:
250 MHz
1000 MHz
Default Clock:
800 MHz
1000 MHz
Overclock:
+-69%

MacBook 2006 w/Snow Leopard; HP B210 printer; print problem; error message: One or more components of the HP printing software are corrupted or missing. Reinstalled software but Mac will not cause printer to print.

? MacBook 2006 w/Snow Leopard; HP B210 printer; print problem; error message: "One or more components of the HP printing software are corrupted or missing..." Reinstalled software but Mac will not cause printer to print. My MacBook Pro works fine with same wireless printer.

Hi ArielAce , thanks for getting back to me!
I would recommend downloading and running the HP Print and Scan Doctor.
Please keep me posted!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

To display a continuos Error Message using BADI

Hi Everybody,
                    There's a transaction that makes use of classes and interfaces to display an ALV grid with input enabled frames and fields. There's a need to display an error message using a specified BADI method, which gets triggered after the user enters the input. The error message is working fine for the first time.<b>But when i'm trying to enter the same input and press enter after the error message, the transaction is getting closed. How can i display the same error message, until and unless the user enters the correct input ?</b> I've tried to trace the control using the debugger after the enter is pressed, but the debugger is also getting closed and the control is coming out of the transaction. Help me out in displaying the error message.

Hi,
Open the interface and go to the Methods tab.
Select the Method and click on Parameters.
In the method parameters, declare a variable
RETURN      Changing      Type     ALM_ME_BAPIRET2_T.
Now, inside your code, declare   DATA : ls_return TYPE bapiret2.
and populate this RETURN table, something like:
        if not ( wa_mara-mtart eq 'SPAR' or wa_mara-mtart eq 'ZMRO' ).
    CLEAR ls_return.
    MOVE 'E' TO ls_return-type.
    MOVE 'ERR_MESSAGE' TO ls_return-id.
    MOVE '999' TO ls_return-number.
    MOVE 'Enter proper error message here' TO ls_return-message.
    INSERT ls_return INTO TABLE return.
    endif.
Then, back in your program, check if this table is empty proceed otherwise, STOP or EXIT.
Regards
Subramanian

DVD Studio burning problem error message: "remove the VIDEO_TS folder from the Build Location"; where is build location

DVD Studio burning problem error message: "remove the VIDEO_TS folder from the Build Location"; where is build location?

Thanks Shane I followed your instructions and it turned out pretty well. One quick question, Im working with DVD Studio Pro 4, how do i implement a theme into my project? I cant even fin where thay are located. Thanks.

How to modify display label in error message raised from capi?

How to modify display label in error message raised from capi?
qms_transaction_mgt.process_rule_violation
( p_br_name => 'BR_PBR_DEL006'
, p_msg_code => 'PMS-00417'
, p_display_label => display_label
, p_table_name => 'pan_project_members'
, p_table_rowid => get_rowid
regards,
marcel

When you mean which columns are displayed, this is actually quite easy.
Display_label will display by default the unique key columns, or if no unique key exists, the primary key. To overrule this behaviour, you have to specify the columns you want to display by assigning them a 'descriptor sequence'.
For example, to display the ename on EMP warnings, assign descriptor sequence 10 to the EMP.ENAME column and regenerate the CAPI package.
Jeroen van Veldhuizen

Monitor Is Flickering - ATI Display Driver Problem Error Message

Similar Messages

Maybe you are looking for