Monitor/TV Output

Does Nokia do a phone, with a nice big screen, similar to the 6280 that will run Sat-Nav but will plug into a screen & output the sat-nav info on it, if that makes sense

No TV-out signal/connector in any currently available Nokia phone model (as far as I know).

Similar Messages

Importing .asf files, blurry in source/sequence monitors and output

I have a large amount of material to work with in .asf form, 480x360 resolution. I'll be outputting to 480x360 as well, so no scaling/zooming needed at all. Problem is, when I import one of those asfs it immediately becomes blurry, i.e. in the source monitor even before I insert it into the sequence and do any modifications. Comparing the imported files to the originals there is a noticeable difference at the exact same dimensions.
I've made sure my sequence settings are at 480x360 resolution. Not sure where else to look on this, any suggestions?
In the past I've done a very similar workflow in PE with no problems, so I'm assuming (hoping??) that there's some easily changed option. Thanks in advance.

Have tried various other permutations in project setup and output - still no luck.
I'm wondering if a clue is the behavior of the program monitor - the clip displays clearly in it until I 'select' the video screen, at which point it blurs just like the output. If I click another area of the screen again, the image resharpens, and so forth. Anyone know what mechanism is causing that?

Discrepancy between HD monitor and output video

Howdy community,
I have a weird problem with Final Cut Pro 7. I have an Asus VW266H HD monitor, set at a good viewing angle on my desk. When I was editing some footage, it looked WAY too dark, so I used a color correction filter and brought the blacks up to 95. The resulting image in the FCP viewer window is the one you see on the left in my screen shot. I hope you can imagine just how dark the original footage was. I was reasonably satisfied with how the footage looked, especially since it wasn't looking "milky" like it can if you lighten/whiten too much in post.
So then I exported the footage, and got the image on the right (in my screen shot). These two images are from the same second of video, on the same monitor. NO changes were made between the exported version in QT on the right and the FCP viewer image on the left.
Why does my monitor and/or the final cut viewer window show me an image that does not represent my output? If the image in final cut and the exported version in quick time look so different, how can I trust my eye in final cut?
Obviously, this is a huge problem.
Please help!!!

If that is the case, how does the editor control how the image looks to others?
You can't. This general problem has been around since the advent of moving pictures. Wander over to the video wall at any big box store and look at the displays. There won't be two that appear alike. All you can do is control the image you send out.
If you are seriously interested in image integrity, get yourself a output device from AJA, BlackMagic, Matrox, etc that can send a qualified signal and a calibrated broadcast TV monitor to to view that signal. Then you'll know what it really looks like.
To paraphrase the old Yiddish saying, "A man with two clocks can never be sure of the time, but, man with an atomic clock, will know."
Good luck.
x

Rendering white flicker on the program monitor and output video file. How to get rid of this flicker in adobe premiere pro cc 2014?

Hello,
I have been working with long sequences in adobe premiere pro cc 2014. All of sudden, I see white flicker in the program monitor and rendered output too. The flicker does not follow any pattern. It is very random.
How to work around on this?
Regards
Naveen Alle

Concurrently working on the same project it requires a specific implementation in all editing programs like Avid's Unity/ ISIS shared storage. That's what you are simply not considering. none of your issues would be any problem if your projects resided on a commonly accessed server or something like that. Check respective hardware solutions.
Mylenium

SHAKE 4.1 : Broadcast monitor flipbook output Crash

Is there anyone could help me with this kind of crash problem ?
My G5 Config are : quad 2.5ghz, 3.5 GB Ram, Decklink Extreme, NVIDIA FX4500, Shake 4.1.
Shake 4.1 always crash at the time when I do flipbook that outputed to broadcast monitor.
G5 2.5Ghz quad Mac OS X (10.4.7)

It's a bug in 4.1......
I have all-most the same system as you
and it crash's when i render to my Deck-link SP CARD, there is no know fix.
The funny thing is, that it work's 100% in the SHAKE 4 demo.
Send a mail to shake support and ask for a Bug fix.
Yours Paul
G5 + DECKLINK SP Mac OS X (10.4.7)

Report to monitor PO output failures

Dear All,
Is there any standard report available in SAP which will display all the PO output failures for a specific period.
Example:
Output type: NEU
Date range: DD.MM.YYYY ~ DD.MM.YYYY
The report should display all the PO numbers of the PO's whose output has failed....
Thanks
Badrinath Murali

You can find in the tables in T-code SE16N
Table-NAST
Output type-KSCHL
ERDAT-created On
ERUHR-Created at
VSTAT-Processing Status as
0     Not processed
1     Successfully processed
2     Incorrectly processed

Monitoring Power output on a POE switch

We just installed 12 AP's on a Cisco 3560 POE switch which currently has 6 AP's already connected to it.
The Customer is asking us to montior the power consumption on the switch.
What are the recommended methods for accomplishing this?
Thanks You for any input!

Kevin,
Have a look at this link:-
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750/software/troubleshooting/g_power_over_ethernet.html#wp1002308
Sample outputs of what to look for
Regards,
Alex.
Please rate useful posts.

How do i monitor/output digital/analogue audio while editing?

I just switched to the mac pro and am learning FCP. Now i am forced to monitor audio output through my headphones. I want to tie the audio into my studio monitors and also be able to send optical audio in to the mac pro from my main mixer, a Mackie 1404. Do i need a DAC(Benchmark), a optical I/O digital mixer or both or something else? My budget is upt to $1,000, but i would like to spend <$300.
In general, i am trying to figure out how to incorporate analog/digital audio/video in to my new editing system. Before this i was outputting analog video/audio in real time with a Velocity I/O card. I am now, obviously, converting to a new way of outputting my finished product and how to edit and work with the new Mac Pro.
I guess i could also consider using the firewire also, right? I haven't worked with a firewire based audio hardware unit, so any info on that appreciated as well.
Also, is the line out in the back of the Mac Pro mono or stereo? I appear to be getting a mono feed while monitoring clips i've shot.
While researching i might list here some things i have come across. Opinions on these appreciated:
Apogee Mini-DAC
Edirol FA-66, 101
Message was edited by: gnostic1919

http://www.blackmagic-design.com/products/decklinkstudio/

Monitor Output

Hi!
I've just set up a small pal tv as an externat monitor. Imac-> trough firewire to d cam-> from cam trough s-video-scart to the tv (only oportunity for me right now)...Motion looks fine in the output, but the image and colours are flickering??
Is this a total wrong setup?Or what seems to be the error?
Any help would be very much aprreciated!

check your cables (disconnect + reconnect, twist them a quarter turn while you monitor the output, swap any you can)
This setup should work fine and I've never seen this problem with multiple variations of cameras, dv convertors etc

Intensity Pro output to Sony monitor problem

I'm monitoring the output from FCP 6.0.2 (OSX 10.5.2) on a MacPro, but the picture has a blue/desaturated colour cast to it (I get the same cast when outputting from Color & After Effects through the Intensity Card). Outputting to a Sony PVM 1454 via the Intensity PAL setting.
I've tested the monitor is OK by plugging the component output from my Canon XH A1 into the monitor via the R G B cables into the corresponding R/R-Y, G/Y and B/B-Y inputs on the monitor & it works fine (color is correct).
The interesting this is though, that the Intensity component cables out of the card are labelled '3R-Y OUT', '4 -Y OUT' and '10 AES/EBU OUT'.
'3R-Y OUT' is plugged into R/R-Y on the monitor
'4-Y OUT' is plugged into G/Y on the monitor
10 AES/EBU OUT' is plugged into B/B-Y on the monitor
Is this correct? I'm also getting (also lots of stripy diagonal lines across the screen).
(I've also tried other combinations of cables - this combination is the only one which gives me any picture at all)
I've checked that the monitor is set to component & that I've not got the monitor set to blue only!!!
Any ideas would be most welcome

Hello Simon,
I assume you're using an Intensity Pro (with Component I/O).
AES is for digital audio, it has nothing to do video.
Please see page 30 of the Intensity Pro manual for the component output connection diagram.
The AES cable should be gray/black.
The video component cables should be red, green and blue.
You also need to set the video output mode in the Intensity preference pane to "HDMI & Y, R-Y, B-Y".
Hope this helps.
Best regards, Oliver

Unable to monitor audio during capture

I'm using FCP6 to capture footage shot with a JVC GY-HD100U at HDV 720p24. I'm using a JVC BR-HD50 deck to capture from, connected to my MacPro 3 GHz quad via firewire.
In the Audio/Video Setting dialog box, the Sequence Preset is "HDV 720P24". My Capture Preset is "HDV", Device Control Preset "HDV FireWire". Video Playback shows "[Missing] Apple Firewire NTSC (720 x 480)" and offers only the options of None and Digital Cinema Desktop Preview–Main as alternate choices. Both HDV options are greyed out. The Audio Playback option is set to Default.
With this setup, controlling the deck remotely from the capture window, I get video but no audio. The only audio I get is when the deck is connected to my video monitor and I use it to monitor the output of the deck. The audio is there when I play back the clips after capture but I cannot monitor the sound with the computer's speakers. If I go to the A/V Devices tab, under Video, it shows the same "[Missing] Apple Firewire NTSC (720 x 480) with the same choices described above, and the Options button next to it doesn't do anything.
Can anyone think of anything I've missed in the initial setup?
Keith
Message was edited by: Keith R Thompson

Keith,
For whatever reason (perhaps the intense processor needs) HDV does not allow you to monitor your audio during capture. The computer just will not do it. What I have done, if I really want to hear what's happening durning capture, is plug my speakers into the headphone jack of my XL H1. Due to the processing that's going on, the audio "lags" behind the video by a couple of seconds.
I'm pretty sure this is not a setup problem, but just a limitation due to the nature of your format.
Hope that helps!
~Luke

Does anyone know how to monitor a microphone when using Voice Over tool?

I use Final Cut studio in conjunction with an AJA Kona LHe card. Audio inputs are via the AJA. I monitor the output from FCP through the AJA card via a Samson C-Control (monitor matrix). Here's my problem. When I'm recording voice over, I am unable to monitor the sound from the microphone through the headphones (or speakers). There is definitely an audio feed being routed to the headphones as I am able to hear the audio cue countdown. The microphone is working fine too - when it comes to playing back the voice over through the headphones (or speakers), I can hear the track absolutely fine. Has anyone experienced the same problem... and do you know how to solve it? Many thanks, AW

its not that you've anything screwy going on .. this is the way it is engineered to work.
the pre-existing audio (and cues) is routed to the headphones but not the voice being recorded.
the solution is to use an audio mixer to monitor both the voice over and the timeline

Aspect ratio of NTSC monitor display

We're working on a FCP 4.5 project that's shot 16:9, and displays with the correct widescreen aspect in the canvas window (so long as pixels are displayed square). However, when I run mirrored video through a Sony DSR11 deck to an NTSC monitor, the picture appears stretched vertically (to fill the screen). How can I correct the aspect of the display in the monitor?
Thanks
Matt Clifton

If I read right the poster is working anamorphic and wants to monitor it properly. Anything that creates a letterboxed display on 4:3 (including a deck conversion will not be monitoring the true signal. It will be a downrezzed and substantially mashed version.
If you need to truly monitor anamorphic output, just "anamorph" the monitor - see above.

NTSC Monitor for Pro CS3

I'm a bit embarrassed to post this, but have not been successful at finding the answer in a search.
When I am running w/ dual monitors and an NTSC monitor, what do I need to do w/ PPro so it outputs just the video (or program video, if you will) to the NTSC monitor - vs. outputting what you would normally see on the computer monitor. I assume it is in the ppro set up menu somewhere.
For now I am running CS3 (soon to upgrade to CS5) - I have the GeForce GTX 470 video card and dual monitors. I just recently purchased a NTSC monitor w/ a HDMI input so I've never had to worry about this, but I've grown tired of burning a DVD only to run up stairs to check color on a television (vs. the computer monitor). I (incorrectly) assumed the card would support dual montiors and a NTSC monitor (I realize this is now being a hardware question) because it also had an HDMI out. That being said, I've was able to find some info on this site (which I love btw) and saw that I could add another video card to supply video to a NTSC monitor.....but I still don't know how to limit the source of either card to the video out put of PPro.
Hope that makes sense...any help would be appreciated.
C.

Since I haven't actually done this, so can't be sure if there is a possible problem, follow at your own risk
Premiere will only recognize 1 graphics card for hardware acceleration, so adding a second card doesn't help on that front. Having said that, I would expect you could add a lower cost graphics card to run more monitors, which I have done and it works fine.
Now, as far as running the signal to a TV/monitor it follows that if you get a card that supports the type of output you desire to run the TV/monitor then it all takes care of itself from there.
On my 2 monitor setup I undock the playback monitor and drag it to the second screen where I can make it larger for better viewing of detail. Seems like you should be able to just drag it over to the TV/monitor then when you are ready to watch the playback there instead of on the computer monitor.
Seems straight forward, but perhaps someone who has actually done this will chime in. There may even be a way to duplicate the playback monitor on multiple screens so you can watch it playing on both the computer monitor and the TV/monitor at the same time?? But I'm guessing that will require an external box to split the output signal to the different destinations.
Hope you get it sorted out.

Xorg 1.5.3, nvidia twinview won't use samsung monitor

I've had a dual head setup going for sometime with no issues, but just got a
new monitor that I can not get working with X. I'm currently using nvida
drivers version 180.22
I have a laptop docked with the laptop screen and a second monitor as my dual head config, it's been great, but something isn't working right with this new monitor. The monitor is a samsung SyncMaster 2493hm, and I've read some things about the Samsung monitors sending incorrect edid info so that may be the issue, but I have no idea how to fix that. The behavior is odd because it appears that x server is spanning both screens as if twinview is correctly setup, but the Samsung monitor never comes on.
I have verified that the monitor works, and works in a dual head configuration both on windows and other linux distro's. My friend has the exact same laptop/monitor setup under ubuntu and it works perfectly for him. Even using HIS xorg.conf didn't work so I am really at a loss.
any help is greatly appreciated.
some basic info:
X.Org X Server 1.5.3
Release Date: 5 November 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.27-ARCH x86_64
Current Operating System: Linux megatron 2.6.28-ARCH #1 SMP PREEMPT Sun Feb 8 09:47:26 UTC 2009 x86_64
Build Date: 17 December 2008 10:46:49PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
lspci output for video card:
01:00.0 VGA compatible controller: nVidia Corporation Quadro NVS 140M (rev a1)
my xorg.conf:
Section "ServerLayout"
Identifier "X.org Twinview"
Screen "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
InputDevice "SynapticsTouchpad" "SendCoreEvents"
EndSection
Section "ServerFlags"
Option "DontZap" "On"
Option "DontZoom" "On"
#Option "Xinerama" "On"
# Option "AutoAddDevices" "False"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/artwiz-fonts/"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/local/"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
EndSection
Section "Module"
Load "xtrap"
Load "glx"
Load "synaptics"
Load "extmod"
Load "dbe"
Load "freetype"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
#Driver "vmmouse" # for vmware
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
Option "SendCoreEvents"
EndSection
Section "InputDevice" # actually an ALPS
Identifier "SynapticsTouchpad"
Option "Device" "/dev/input/mouse3"
Driver "synaptics"
Option "AlwaysCore" "true"
#Option "Device" "/dev/input/mice"
Option "Protocol" "auto-dev"
Option "SHMConfig" "on"
Option "LeftEdge" "130"
Option "RightEdge" "840"
Option "TopEdge" "130"
Option "BottomEdge" "640"
Option "FingerLow" "7"
Option "FingerHigh" "8"
Option "MaxTapTime" "180"
Option "MinTapTime" "110"
Option "ClickTime" "0"
Option "EmulateMidButtonTime" "75"
Option "VertScrollDelta" "20"
Option "HorizScrollDelta" "20"
Option "MinSpeed" "0.40"
Option "MaxSpeed" "0.65"
Option "AccelFactor" "0.0020"
Option "CircularScrolling" "1"
Option "CircScrollDelta" "0.1"
Option "CircScrollTrigger" "3"
#Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
HorizSync 28.0 - 64.0
VertRefresh 43.0 - 60.0
Option "DPMS"
EndSection
Section "Device"
# Force Powermizer to a certain level at all times:
# 0x1 = high
# 0x2 = mid
# 0x3 = low
# let GPU set perf level by temp
#Option "RegistryDwords" "PerfLevelSrc=0x3333" # new 8/12, may conflict with above.
# Disable vblank interrupts
Identifier "NvidiaCard"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "G72M [Quadro NVS 110M/GeForce Go 7300]"
Option "RenderAccel" "True"
EndSection
Section "Screen"
#Option "TVOutFormat" "COMPOSITE"
Identifier "Screen0"
Device "NvidiaCard"
Monitor "Monitor0"
DefaultDepth 24
Option "UseEdidFreqs" "True"
Option "TwinView"
Option "MetaModes" "nvidia-auto-select,nvidia-auto-select"
Option "TwinViewOrientation" "LeftOf"
#Option "AddARGBVisuals" "True"
Option "AddARGBGLXVisuals" "True"
Option "NvAGP" "1"
Option "HWCursor" "Off"
#Option "ConnectedMonitor" "DFP" #"DFP" for DVI connections only, otherwise "CRT"
Option "TripleBuffer" "True"
Option "DamageEvents" "True"
Option "BackingStore" "True"
#Option "PixmapCacheSize" "300000"
Option "OnDemandVBlankInterrupts" "True"
#Option "TVStandard" "NTSC-M"
Option "RegistryDwords" "PowerMizerLevelAC=0x2 # new 8/12"
SubSection "Display"
Depth 24
Modes "nvidia-auto-select"
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Disable"
EndSection

I have a Samsung 245BW 24 inch monitor (gorgeous output by the way) that works perfectly. This is my xorg.conf. A slighly different version worked perfectly when I had two of these monitors.
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Samsung"
ModelName "Samsung SyncMaster"
HorizSync 30.0 - 81.0
VertRefresh 56.0 - 75.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 8800 GT"
Option "DPI" "96 x 96"
Option "UseEdidDpi" "false"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
EndSubSection
EndSection

Monitor/TV Output

Similar Messages

Maybe you are looking for