Monitoring details for UCS-C servers

Hi,
If I look in the document at the link below, I have the impression that disk failures, power supply failures etc. are not alerted for Cisco UCS-C series rack-mount servers:
http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/smart_call_home/user_guides/MonitoringDetails.pdf
Is that correct?
Best regards

Hi David,
Whether SCH hardware failure alerts are available for Cisco UCS-C servers depends on how you have it set up.
Is your UCS-C server integrated with UCSM? If so, all UCSM supported alerts are applicable to the integrated UCS-C servers as well. In that case, you can refer to the UCSM alerts section of the Monitoring Details, which does seem to include some hardware failure alerts.
For more information on UCS-C/UCSM integration, check out the Managing UCS-C Server with SCH app note.
If your UCS-C server is not integrated with UCSM, or if the UCSM hardware failure alerts are not what you are looking to monitor, reply in this thread, and I'll see what else I can find out.
Thanks,
Kelsey

Similar Messages

Distribution Monitor for 2 different servers from 2 different sites

Hello all,
We are trying to use Distribution Monitor during a parallel Unicode Conversion on a SAP 4.7 system.
The source system and target system are 2 different servers located on 2 different sites (more than 500Kms distant).
Questions:
1. Can we use Distribution Monitor with 1 source server dedicated for the Export and 1 target server dedicated for the import of a package?
2. If it is not possible, what are the constraints in fact?
3. Can we have a scenario where Distribution Monitor is used on the source system in order to use the parallelism benefit and Migration Monitor used on the target system?
Thanks for your help & feedback,
Chris

Hi Chris,
1. Can we use Distribution Monitor with 1 source server dedicated for the Export and 1 target server dedicated for the import of a package? The Answer is No
In order to use Distribution monitor, u need minimum two application servers on source systems and correspondingly atleast minimum two application servers on target system
For example let us say Application server A and Application server B on sources systems and Application Server C and Application server D on target ytem
Then configure Distribution monitor properties to include two application servers as source systems and two application servers as target systems. When u exeute distribution monitor preparation, first it scan database servers in source system nd target system and then scan CI servers in source and target system. Then Packages will be distributed in two application servers A and B
Run Export from Application server A for first fifty packages , at the same time Run import these first fifty packages in Application Server C
Run Export from Application Server B for other remining packages and at the same time , run import the remaining packages into Application Server D.
(that is one to one correspondence)
2. If it is not possible, what are the constraints in fact? - There is no constraints. However there is lots of time consuming during Distribution monitor preparation and checking.
3. Can we have a scenario where Distribution Monitor is used on the source system in order to use the parallelism benefit and Migration Monitor used on the target system? - The Answer is No.
You cannot mix distribution monitor tool for source system and Migration tool used on target system.
You have to use any one tool depending on the size of database used.
if your database size used is very very large then recommend to use distribution monitor where u in sou can have multiple R3load jobs in each application server. Say Application server A use 20 R3load jobs and Application server B use 15 r3load jobs).
Thanks
APR

Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

Does Cisco Prime Infrastructure supports monitoring CPU,Memory, HDD for UCS , VMWare?

Prime Infrastructure/ Assurance is positioned today more towards managing network elements and network performance, rather than server infrastructure. We are in the process of adding Datacenter component support, with more focus on Nexus and UCS- due later this year.
Having said that, Prime Infrastructure allows the system user to add custom SNMP polling templates, which can then be used for polling any SNMP based values from any SNMP enabled device. These can be used to collect the information you specified below and the polled information will be available in dashboards and reports.

Gathering Hardware Utilization Statistics for UCS B/C Series via SNMP - Is it possible?

It is possible to gather typical cpu, memory, fan speed, and hdd utilization statistics from the Cisco MIBs for UCS B / C series servers?
The excellent Cisco UCS Monitoring Resource Handbook (https://communities.cisco.com/docs/DOC-37197) provides a link to the following document for MIB Loading Order and Statistics Collection Details:
MIB Reference for Cisco UCS Standalone C-Series Servers:
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/mib/c-series/b_UCS_Standalone_C-Series_MIBRef.pdf
In Table Four of the above referenced document, it contains various MIBs/OIDs used for gathering statistics.
For example, this processor section:
Processor
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB
.1.3.6.1.4.1.9.9.719.1.41 is the parent OID where the key statistics reside.
processorEnvStats—Provides all CPU power and temperature statistics for every CPU socket.
processorUnit—Provides all CPU statistics for every CPU.
When walking the following C Series with the suggested OID:
snmpwalk -v2c -c XXXXXXX -m ALL XXXXXX sysdesc
SNMPv2-MIB::sysDescr.0 = STRING: Cisco Integrated Management Controller(CIMC) [UCS C220 M3S], Firmware Version 1.5(1l) Copyright (c) 2008-2012, Cisco Systems, Inc.
I get the following output:
snmpwalk -v2c -c XXXXXXX -m CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB XXXXXXXX cucsProcessorUnitTable
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitDn.1 = STRING: "sys/rack-unit-1/board/cpu-1"
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitDn.2 = STRING: "sys/rack-unit-1/board/cpu-2"
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitRn.1 = STRING: cpu-1
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitRn.2 = STRING: cpu-2
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitArch.1 = INTEGER: xeon(179)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitArch.2 = INTEGER: xeon(179)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitCores.1 = Gauge32: 4
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitCores.2 = Gauge32: 4
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitCoresEnabled.1 = Gauge32: 4
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitCoresEnabled.2 = Gauge32: 4
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitId.1 = Gauge32: 0
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitId.2 = Gauge32: 1
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitModel.1 = STRING: Intel(R) Xeon(R) CPU E5-2643 0 @ 3.30GHz
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitModel.2 = STRING: Intel(R) Xeon(R) CPU E5-2643 0 @ 3.30GHz
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitOperState.1 = INTEGER: operable(1)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitOperState.2 = INTEGER: operable(1)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitOperability.1 = INTEGER: operable(1)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitOperability.2 = INTEGER: operable(1)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitPerf.1 = INTEGER: ok(1)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitPerf.2 = INTEGER: ok(1)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitPower.1 = INTEGER: unknown(0)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitPower.2 = INTEGER: unknown(0)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitPresence.1 = INTEGER: equipped(10)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitPresence.2 = INTEGER: equipped(10)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitRevision.1 = STRING: unknown
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitRevision.2 = STRING: unknown
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitSerial.1 = STRING: Not Specified
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitSerial.2 = STRING: Not Specified
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitSocketDesignation.1 = STRING: CPU1
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitSocketDesignation.2 = STRING: CPU2
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitSpeed.1 = INTEGER: 3300
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitSpeed.2 = INTEGER: 3300
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitStepping.1 = Gauge32: 0
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitStepping.2 = Gauge32: 0
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitThermal.1 = INTEGER: unknown(0)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitThermal.2 = INTEGER: unknown(0)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitThreads.1 = Gauge32: 8
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitThreads.2 = Gauge32: 8
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitVendor.1 = STRING: Intel(R) Corporation
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitVendor.2 = STRING: Intel(R) Corporation
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitVoltage.1 = INTEGER: unknown(0)
CISCO-UNIFIED-COMPUTING-PROCESSOR-MIB::cucsProcessorUnitVoltage.2 = INTEGER: unknown(0)
Typical CPU performance graphs provide percentage integers in vertical or y-axis and time in the horizontal or x-axis. The suggested OID yields no percentage utilization which I can graph. Am I correct in concluding that we must poll the hypervisor for this data instead of the CIMC directly?
Thanks,
Amir

Hi tak,
my suggestion is to place the main prog outside the loop B but inside loop A. This makes sure, that Loop A is turning once with every execution of the main prog. Beside this Loop B is executing independently. Then you need some communication between your main program and the loop B which can be implemented easiest with global variables, one for each communication direction. This could look like this to abort the main prog on "emergency":
and to tell the Loop B to stop on finish of the Main prog:
In the main prog- VI (which is a bit weird, because the while loop execute always and only once and therefore is unnecessary) your experiment shoult execute in a while loop, since it is abortable dynamically. The for loop will execute the predefined count, defined by wiring the "loop count"- terminal or wiring an array with autoindexing.
I hope this helped a bit,
dave
Message Edited by daveTW on 06-17-2006 02:13 AM
Greets, Dave
Attachments:
multiple_loop_w_different_duration.png ‏4 KB
experiment.png ‏3 KB

How to configure windows services alerts in SCOM 2012 for all agent servers. For eg, Terminal Services, Netlogon, RPC etc..

Hi,
I need to configure different windows services alerts in SCOM 2012. Below are some of the windows services I need to monitor through SCOM.
Serivce: Windows Management Instrumentation
Service: Netlogon
Service: Remote Procedure Call (RPC)
Service: Server Service
Service: Terminal Services
Service: Windows Time
Service: Workstation
Service : WWW Publishing Service
Could some one please assist or share me the details, how to configure these services for windows agent servers.
Thanks..
Regards, Rajeev Parambil

Hi,
A certain set of services are monitored by default on all agents:
DNS Client
DHCP Client
RPC
Workstation
Server
For all the other services you could create a service monitor.
A nice blog series outlining this process can be found here: http://www.bictt.com/blogs/bictt.php/2011/03/16/scom-monitoring-a-service-part1
It's doing common things uncommonly well that brings succes. Check out my SCOM link blog:
SCOM link blog

Details for 'Is Web service security available?'

Hi i am working on scenario rfc to webservice.Its as secued webserivce i need to do ssl configuration.
In component monitoring..for the integration engine its in yellow...
Details for 'Is Web service security available?'
Communication error Proxy calls on the sender or receiver side are not permitted on the IS (client)
can any one please help me out..
Thanks
sriram

I have already installed certificates on the j2ee engine & i have given the paramaters for keystore entry & keystore value.Still i have the same error
In component monitoring
For integration engine
Details for 'Is Web service security available?'
Communication error Proxy calls on the sender or receiver side are not permitted on the IS (client)
In message monitoring
Audit Log for Message: f614df00-e9e0-11da-95ef-0004ac577b32
Time Stamp Status Description
2006-05-22 15:18:58 Success The message was successfully received by the messaging system. Profile: XI URL: http://saptst01:51000/MessagingSystem/receive/AFW/XI
2006-05-22 15:18:58 Success Using connection AFW. Trying to put the message into the request queue.
2006-05-22 15:18:58 Success Message successfully put into the queue.
2006-05-22 15:18:58 Success The message was successfully retrieved from the request queue.
2006-05-22 15:18:58 Success The message status set to DLNG.
2006-05-22 15:18:58 Success Delivering to channel: ZCH_VERISIGNPPGR
2006-05-22 15:18:58 Success SOAP: request message entering the adapter
2006-05-22 15:18:58 Success SOAP: call failed
2006-05-22 15:18:58 Error SOAP: error occured: iaik.security.ssl.SSLException: Peer sent alert: Alert Fatal: illegal parameter
2006-05-22 15:18:58 Error Exception caught by adapter framework: Peer sent alert: Alert Fatal: illegal parameter
Can any one please help me out.
Thanks
sriram

Trace level of RWB's Message Monitoring - Detail Message - Tab "Audit log"

Hi,
My flow is: File -> PI -> Transformed File with seeburger module. Everything is good except the trace level in RWB.
Exactly, in our PI production, under RWB -> Message Monitoring, when I select a message (e.g PI -> Outside) and see its Detail, under tab "Audit Log", I have a log with only 2 pages (which corresponds to the sender part "File -> PI")... whereas in our PI pre-production, I have 4 pages for the exact same flow, on which I have also info of the receiver part "PI -> Outside"...
My question is just: do you know which parameter is involved in this trace level of RWB's Message Monitoring Detail log ?
regards.
Mickael
Note: in [Help SAP|http://help.sap.com/saphelp_nw04/helpdata/en/fd/16e140a786702ae10000000a155106/frameset.htm], I see only this sentence "Audit Log: The audit log for the selected message is displayed as the default setting.".
Edited by: Mickael Huchet on Oct 18, 2011 1:59 PM

Hi Shabarish,
Thanks that will help to localize my search.
else by hazard, you don't know which parameter in this tree is for the "Audit Log"?
coz I did a quick look in prod and pre-prod, but it seems the severity is the same (e.g "Info" for most of them) whereas the trace level of "Audit log" is different.
Thanks for
Regards.

'BBPSC11' error in Monitor SC for one User having multiple positions but on

Hello,
'BBPSC11' error in Monitor SC for one User - having multiple positions in org structure - but having one BP code associated to all positions.
We have one BP ID associated to multiple positions of the same user - in multiple org structure.
The org unit is refered as one Project and like wise we have multiple projects people worked on.
Once the Proj is over we move the Users from one Proj (Org unit) to another Proj, with new Position created copying the old and associate old BP code to it.
With this when we go for Monitor SC option - enter User ID in Created By field - old SC are listed but we are getting error if we click on the Detail icon.
Error:The Internet Transaction Server could not start the transaction "BBPSC11" because of the following error: Attribute for user contains errors. Inform systemadmin. .
AD

Hi,
Pl. verify the user with txn-bbp_attr_check. It could be that the org. relationship of the user changed with what was captured on shopping cart. Also use txn-users_gen to repair the user.
Regards,
Sanjeev

Monitoring messages for BPM

How do we monitor the messages processed through BPM?
when do we use SXMB_MONI and SXMB_MONI_BPE exactly? which of these used for BPM processes?

Hi,
If you don't SAP Service Market place user Id , then refer this document-
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/e7bc3a5a-0501-0010-1095-eb47159e169c
If you want to monitor details of the BPM with technical details or workflow log or messages inside the BPM then either you can use SXMB_MONI_BPE or you can go from SXMB_MONI->PE->Technical Details
Regards,
Moorthy

NT startup parmaters for multiple weblogic servers started as a service

I have the need to start multiple weblogic servers, using NT services.
I have created a second folder with a properties file listening on another
port.
I am using the following startup parameter
-J-Dweblogic.system.name=Test
My question, this works when I type the startup parameter, is their anyway
to have this automatically entered
on server startup.
Is their a registry setting to make this permanent
Thanks

The answer is...
- Use a product to turn applications into an NT Service (e.g.
ServiceMill)
- Directly run the Weblogic Server Java class via that application
--> As many WLs on one machine as you like.
Send mail if you need specific details.
Best regards
Daniel Hoppe
-----Original Message-----
From: [email protected] (Ed) [mailto:[email protected]]
Posted At: Wednesday, August 30, 2000 2:34 AM
Posted To: install
Conversation: NT startup parmaters for multiple weblogic servers started
as a service
Subject: Re: NT startup parmaters for multiple weblogic servers started
as a service
I wish that was the case.
The problem is, while you enter the startup parameter once, it only
is good for that startup of the weblogic server,
The next time the server reboots and the services start, unless you
re-enter the startup parameter -J-Dweblogic.system.name=Foldername
The weblogic server starts using the wrong properties file.
Is their anyway using NT services to have the correct instance of WL
to start everytime.
I have checked this newsgroup and this question has been posted
before, but so far no one seems to have the answer.
I know in a production eniviorment someone must be running more that
one instance of a WL server as a service, Hopefully their is an
answer on how this is done.
Thank you
Kumar Allamraju <[email protected]> wrote:
Not that i know of.
but you are specifying this startup parameter only one time too!!!
Kumar
None of your bussines wrote:
I have the need to start multiple weblogic servers, using NT
services.
I have created a second folder with a properties file listening onanother
port.
I am using the following startup parameter
-J-Dweblogic.system.name=Test
My question, this works when I type the startup parameter, is theiranyway
to have this automatically entered
on server startup.
Is their a registry setting to make this permanent
Thanks

Autoscale has not been able to read any monitoring data for ...

We´re receiveing an Error Message from the Autoscale functionality for a complete week now. This has happened before when the "Storage incident" happened. But the problem was resoloved when the functionality of the Storage was fixed. But since
the 22th of December it seems that the autoscaling dosn´t work any more. All of the Autoscaled Machines are up while we´re having almost no traffic during the holidays.
Is there someone who has a solution? Or is this one of these "drop all machines and recreate them" issues?
The error message is:
Autoscale has not been able to read any monitoring data for XXX:XXX since 12/22/2014 11:39:01 AM UTC
Autoscale task failed for XXX:XXX due to no metrics available

Hi Marc,
We could view the
latest information from Azure Dashboard
http://azure.microsoft.com/en-us/status/#history
12/22
Storage - East US - Partial Service Interruption
From 10:10 to 11:40 UTC on 22 December, 2014 a limited subset of customers using Storage in East US may have experienced intermittent latency or time out errors when attempting to reach storage resources. This incident has now been mitigated.
Since
Autoscale requires monitoring data to be collected from your VM/role instances in order to scale . While
there have network issue on the storage
accounts that contain your monitoring data, so it will fail to autoscale.
Now, this incident has now been mitigated.I suggest that you could check if
Autoscale work vey well.
In addition,I suggest that you could refer to the link below
for more details regarding Autoscale not working:
https://social.msdn.microsoft.com/Forums/azure/en-US/bc2048c4-8d49-4c54-b150-f263808c4b7a/notification-could-not-automatically-scale-xxx-because-monitoring-data-was-not-found?forum=windowsazuremanagement
Best Regards,
Kevin Shen.

SCEP 2012 System Center Monitoring Pack for Linux v4.5.10.1 Problem

Hi Everyone!
We are having a problem with OpsMgr 2012 R2 and the System Center Monitoring Pack for SCEP 2012 for Linux v4.5.10.1. We have successfully deployed the Linux OpsMgr 2012 R2 agent to our test CentOS 6.5 VM as well as SCEP 2012 v4.5.10.1. We have
imported the System Center Monitoring Pack for SCEP 2012 for Linux management packs into OpsMgr 2012 R2 which is successfully discovering SCEP on our Linux VM, but when looking at the details for the monitor, it indicates that SCEP is "not found"
as seen in the following screen shot...
As seen in the following screen shots, everything else seems to be installed, configured, and working properly...
Any assistance or guidance would be greatly appreciated!
Regards,
JJ

Magnus_001 (big ups) and I were able to get discovery to stop failing on the Linux side of things, but the SCOM MP is still highly problematic. Their pdf guides for SCEP implementation on Linux has a bunch of typos and errors -- for example, listing
'/bin/sh' instead of '/bin/bash', and one of the lines (the one that includes "export LANG=C" won't run no matter what. When we disassembled the SCOM MP, we found that there's an extraneous space at the end of the command, current thought is
that that's causing a regex to fail within sudo. All of their commands, from what I can tell, need to be specified as NOPASSWD within sudo; if you see errors about ssh-askpass with that you can confirm that there are likely typos in their guide sourced
from the pdf. We eventually allowed '/bin/bash' to get the programs to run since we couldn't get a regex match to catch their command (which should be in a script). We are out of failures that we can discover with logging on the Linux side; it's
likely to be an error within the MP at this point.
When we look at the powershell script in the MP library, the "not found" error is the default state, set immediately after stdout is captured from the discovery script. I'm guessing that there's some problem interaction between that script
and the parsing thereof, as when we run the script locally as root we see the output that we'd expect. For all I know that's a line ending or locale problem.
Troubleshooting on the linux end is problematic, as instead of distributing a script to check on the linux side (which makes the sudo part of things much easier), the script is hard-coded within the MP. From what I understand it would need to be disassembled
and recompiled to change.
The snippet below may be of use to someone for use in their sudoers file, it will make the checks work on the linux side at least. I wouldn't recommend this for anything beyond testing, as specifying that an account can run a full bash shell as root
without a password is a terrible idea.
#replace scomactionaccount with whatever your scom action account is called
User_Alias SCOM = scomactionaccount
Runas_Alias SCOM = root
SCOM ALL = (SCOM) NOPASSWD: /opt/microsoft/scx/bin/scxlogfilereader -p
SCOM ALL = (SCOM) NOPASSWD: /bin/bash

SLR - transaction response time for all appl. servers together

Hi,
we want to have in SLR response time for defined transaction. We have activated necessary steps for monitoring transactions, started CPH and we can see in SLR average response times.
We have several application servers and we want to have in SLR TOTAL response time for all appl. servers together.
Is it possible? What is necessary steps to do it?
Thanks for all hints.
Regards,
Roman

Hi Andreas,
Another way to approach this would be to use CCMS transaction monitoring by maintaining table ALTRAMONI (in the satellite system) as described here: http://help.sap.com/saphelp_nw70/helpdata/en/b3/468e3b093d4031e10000000a11402f/content.htm
In RZ20 you'll be able to see the last 24 hours of performance data in a 1-hour granularity, as well as the last 30 minutes in a higher granularity. Depending on your requirements you can then configure alerting so that you get an email when performance passes a certain threshold.
Jon

System monitoring plugin for Vmware ESX server..

i have a OEM grid control 10.2.0.5 with management plugin for Vmware ESX server (Management Plug-in: vmware_esx_server, Version 1.1.3.1.0) added.
I later added another server agent for management/monitoring of VMware ESX server.
the agent state is UP and under Monitored targets for the agent I am now trying to add the VMware ESX server
Once on the page, here I enter the details <Hostname / Usrname:Pwd / Protocol:HTTPS / Keystore> and click on Test Connection and recieve a Warning :
Failed to contact the target to be added. Following errors were received while testing the connection to the target. Update the properties accordingly, try Test Connection for testing the properties before saving.
TestVersion - caught com.vmware.vim.InvalidLogin: ; nested exception is: javax.net.ssl.SSLException: java.lang.RuntimeException: Unexpected error: java.security.InvalidAlgorithmParameterException: the trustAnchors parameter must be non-empty Aug 26, 2009 9:28:04 AM org.apache.axis.utils.JavaUtils isAttachmentSupported WARNING: Unable to find required classes (javax.activation.DataHandler and javax.mail.internet.MimeMultipart). Attachment support is disabled.
If I go ahead and click OK it adds the Target(Vmware esx server) to the agent and displays message :
"Target ESXVS (VMware ESX Server) has been added."
THE problem starts here.. the metrics collection doesnt happen for the target and I get Metric collection errors.
I have tried checking in diff versions of management plugins as well as tried adding the target to the Grid control's agent//
Pls help..

Is the location that you specified for the keystore file somewhere that the agent can read from (either a drive local to where the agent is installed or a network drive that the agent has access to)? Is the keystore file one that was generated for that specific ESX Server from its rui.crt file? Each ESX Server has a different rui.crt file that you use to create the keystore file.
You won't be able to collect metrics if the SSL connectivity isn't set up correctly.
Dave
Edited by: user716739 on Aug 26, 2009 4:54 AM

Import System Center Monitoring Pack for System Center 2012 - Service Manager into SCOM 2007 R2

I would like to know if there is SCSM 2012 SP1 MP available for SCOM 2007 R2 ?
I downloaded the "System Center Monitoring Pack for System Center 2012 - Service Manager" MP from
http://www.microsoft.com/en-us/download/details.aspx?id=29980 and then import into SCOM 2007 R2, however, I found that there are some MP dependencies issue.
For example, the "Microsoft System Center Service Manager Library" MP requires "Microsoft SystemCenter Library" and "System.Health.Library" MPs of version 7.0.8427.0. Howerver, the "Microsoft SystemCenter Library"
and "System.Health.Library" MP in SCOM 2007 R2 is of version 6.1.7221.0

Import Management Pack from DVD disk SCOM 2012 R2
SW_DVD5_Sys_Ctr_2012_R2_English_OpsMgr_MLF_X19-18307.ISO\ManagementPacks
Have a nice day !!!

Monitoring details for UCS-C servers

Similar Messages

Maybe you are looking for