Monitoring Template Creation question

Hello,
I have created a Monitoring Template (T1) by performing a "Create Like" of the Standard Oracle Database Instance template. Unfortunately the Standard Oracle Database Instance template does not have all of the metrics that I need to check.
Is there a way to create a Monitoring Template based on "All Metrics" for the DB Instance? (It appears that I can only create a monitoring template based on a target database)
If not, how can I pick a particular metric from the "All Metrics" list and add it to a template?
Thanks,
Bob Larsen

When creating a Template based on a Target, you actually wll get all available metrics. You could also use the Oracle proved template to copy from.
You should realize that when looking at All Metrics, several of these metrics are "Non threasholdable" meaning that you simple can not set a threshold value.
Regards
Rob
http://oemgc.wordpress.com

Similar Messages

CCMS - issue configuring new IDoc monitor template

Hi,
we wan´t to create a new CCMS IDoc monitortemplate in our central ALE configuration system and define all relevant remote SAP System and transport the complete template to the Solution Manager System.
We wan´t to customize the template in the ALE configuration System, "not" in SolMan.
These are the steps i´ve already done.
1. create new MTE´s by transaction BDMONIC2
2. customize the new MTE´s by tr. BDMONIC
3. create a new Template in RZ20
4. create a new Monitor for the new TEMPLATE in RZ20
5. after some minutes (the new created MTE´s are available for configuration)
First question. Why i have to wait some minutes to see the new MTE´s in the new monitor ?
anyway,
the monitortemplate for my own system(template creation system) is working fine.
6. Now i´ve created new entries to monitor remote SAP Systems in RZ21
7. I can see the new SAP Systems in my new TEMPLATE in RZ20
8. I would like to use my created MTE´s for every SAP System. Transport all MTE´s and configuration to the relevant SAP Systems.
9. I can see all entries in BDMONIC2 and BDMONIC in the remote System ...
... but I can´t see the new MTE´s in RZ20 in the remote System and
I can´t see the the new MTE´s (for the remote system) in my new TEMPLATE in the ALE configuration System (where the remote system is assigned).
note: I saw that a new MTE creates a new alert class in RZ21.
This class is filled in the template creation system(ALE configuration) but not in the remote system.
Any ideas what is going wrong here ?
thx,
Gordon
Edited by: Gordon Breuer on Jul 30, 2009 2:28 PM

Hi,
check this links:
http://help.sap.com/saphelp_nw04s/helpdata/en/9d/df1241c738f423e10000000a155106/frameset.htm
https://www.sdn.sap.com/irj/sdn/forums
Regards,
Spandan

MAI monitoring templates vanished (SolMan 7.1 SP10)

Hello all,
it seems like almost all of our MAI monitoring templates have vanished in our SolMan 7.1 SP10 system.
I still get the traingles were templates existed, but when expanding on them the won't Show up.
I updated SAP Service Content yesterday and SAP Monitoring Content today to the latest version.
I'm nor sure if this really caused the trouble.
Does any of you ever have experienced something similiar?
Best Regards,
Thorsten

Hello,
the question was answered by SAP Support.
One has to be logged on in the language in which the templates were created / maintained.
I switched from German to English last week, so that's the reason why.
Regards,
Thorsten

Monitoring template and alert noifications, how ?

I have set up database monitoring template with some metric tresholds for warning/alerting. Also, I applied this to the databases. Now, my question is how will i be notified (say via e-mail) once an alert has generated ? I see notification methods and notification rules, where it has its own metric settings. Do i have to apply notification rules to these databases for notifications. If so, what is the use of monitoring template ? Can i set up notifications via e-mail within the monitoring template ?
thanks,

In EM12c, go to the 'Enterprise' menu, then 'Job', then 'Library'. There should be an out-of-the-box job called "DISABLE TABLESPACE USED (%) ALERTS FOR UNDO AND TEMP TABLESPACES" that you can run against your database targets, and that job will disable database-generated alerts.
If a previous admin has set up EM12c-generated alerts for undo and temp, then yes, a monitoring template will take care of disabling them. Either remove those alerts from the existing monitoring template and apply them to your targets, or create a new monitoring template based on one database's current settings, remove those warning/critical thresholds for your undo and temp tablespaces, and apply it to your targets.

Monitoring Templates Versus Notifications

please correct me if I am wrong, when we set up Notifications, OEM with use the default metrics to send email if errors/warnings occur. what if, I have monitoring templates set up with our own metric, how does this monitoring templates work together with notifications? I guess, my question is how can I assign the monitoring Templates so I can get email based from the metric I assigned.
I am a little confused about how these two worked, if something can give my some insight, I would greatly appreciated.

I generally see monitoring templates and notifications as two separate entities. First evaluate if some of your metrics are better managed as a UDP, user defined policy, than metric. I have templates for production, non-production, hpux, linux, aix, etc. I then apply that template to the corresponding policy for updates or changes in standards. I then would go to preferences and notifications/rules and create a notification rule. I generally create one notification rule per user based on that user's group of clients. That way when someone is out another DBA can cover by simply adding that target to their group.
Hope that answered your question or wasn't too much info. Let me know if you have anything further.
Cheers,

How to use XDOXSLT in rtf template layout for etext template creation

<DEFINE CONCATENATION>     BookDetails
<BASE LEVEL>     Category
<ELEMENT> Name || '/' || Price
<DELIMITER>      '/'
<END DEFINE CONCATENATION>     BookDetails
With EFTProcessor the above details are created in xsl file as follows
<xsl:template name="CONCAT_BookDetails">
*I need to declare one more variable here
EG: <xsl:value-of select="xdoxslt:set_variable($mycount, count(.//Category))"/>
--and use this variable for any dyanamic process inside this template. How to achieve this in rtf template by declaring a xdoxslt function. How to declare this
syntax in rtf layout so that it creates a varibale in xsl template using the EFTProcessor. Please help me out. The main point here is to include xslt functions in
rtf template layout for etext template creation.*
<xsl:for-each select=".//Category">
<xsl:call-template name="CONCAT_BookDetails_V"/>
</xsl:for-each>
</xsl:template>

in the next time use BI Publisher forum - BI Publisher
<?format-number(ENTERED_CR,'##,##0.00')?>it's works for me
output:
444    -> 444.00
444.55 -> 444.55

VMM 2012 R2 Template creation fails with sysprep error via the gui, but works in powershell?

I'm in the process of trying to convert an existing gen1 VM (Win Server 2012 R2) to a VM template using VMM 2012 R2 with rollup 1. The creation keeps failing with the following error :-
"Error
(2901)The operation did not complete successfully because of a parameter or call sequence
that is not valid.Recommended ActionEnsure
that the parameters are valid, and then try the operation again."
I've checked that the local administrator account for the machine being converted to a template and it is blank as expected and in an attempt to troubleshoot I've output the template creation script via the VMM GUI and executed the commands in order which appears
to have resolved the problem, well the template finishes creation, i'm yet to deploy a machine via it?
# Create VM Template Wizard Script
# Script generated on Thursday, April 3, 2014 12:52:15 PM by Virtual Machine Manager
# For additional help on cmdlet usage, type get-help <cmdlet name>
$VM = Get-SCVirtualMachine -VMMServer localhost -Name "MyTemplate_Template" -ID "98299447-83e1-4d98-a558-a96ebafcf9b5"
| where {$_.VMHost.Name -eq "myhost.mydomain.com"}
$LibraryServer = Get-SCLibraryServer -VMMServer localhost | where {$_.Name -eq "my.library.com"}
$GuestOSProfile = Get-SCGuestOSProfile -VMMServer localhost | where {$_.Name -eq "Windows Server 2012
R2"}
$OperatingSystem = Get-SCOperatingSystem -VMMServer localhost -ID "50b66974-c64a-4a06-b05a-7e6610c579a2"
| where {$_.Name -eq "Windows Server 2012 R2 Standard"}
$template = New-SCVMTemplate -Name "My Template" -RunAsynchronously -VM $VM -LibraryServer $LibraryServer
-SharePath "\\mylibrary.mydomain.com\SCVMM Library\Templates\mytemplatedestination" -GuestOSProfile $GuestOSProfile -JobGroup d2f2f539-85da-4091-ab08-abe739fc4761 -ComputerName "*" -TimeZone 85 -FullName "Administrator"
-OrganizationName "My Organisation" -Workgroup "WORKGROUP" -AnswerFile $null -OperatingSystem $OperatingSystem
Now the only fields that weren't populated when I ran through the gui were FullName and Organization? Before I changed the script these two fields were just set to ""? Is that what has potentially caused the issue are they both required fields?

Your not the only one who can reproduce this. Did you ever find out what it was? I saw your post and tried your same work-around and it also worked for me via Powershell.

Virtual desktop template creation with UR1 - two issues

There are two new issues affecting Virtual Desktop template creation with WMS 2012 with UR1.
Issue #1: Some systems fail to create a new or customized virtual desktop template with UR1 applied. UR1 includes an updated MultiPoint Connector which is compatible with a UR1 host. The Connector gets included in the Virtual Desktop template
so that the virtual desktops can be managed by MultiPoint Dashboard. On some systems installation of the UR1 Connector will require a reboot that takes too long to complete and template creation will timeout.
If you try to create a template without doing the following update to the unattend-t.xml file, and if the Connector reboot takes too long, the template creation process will never complete, appearing stuck at 80% until the timeout. If you check the running
Virtual Machine Connection, you will see an error message that Windows could not complete the installation.
To correct this:
From MultiPoint Manager or Hyper-V Manager, shutdown the running template VM.
Delete the template .vhd stored in Public Documents\Hyper-V\Virtual hard disks
3. a) Make a backup copy of
C:\Program Files\Windows MultiPoint Server\Unattend-t.xml
e.g. rename it .bak
b) open
C:\Program Files\Windows MultiPoint Server\Unattend-t.xml in your favorite text editor.
b) find “connector” in the file
c) replace this string (starts with <Path> and ends with </Path>)
<Path>powershell -Command "try { $process = Start-Process -FilePath '%Windir%\Temp\Connector\WmsConnector.Exe' -ArgumentList '/Quiet' -PassThru -Wait; } catch { throw 'WmsConnector
Install Failed'}; exit $process.ExitCode"</Path>
with this string
<Path>powershell -Command "try {
$p = Start-Process -FilePath '%Windir%\Temp\Connector\WmsConnector.Exe' -ArgumentList '/Quiet
/NoRestart' -PassThru -Wait; } catch { throw 'WmsConnector Install Failed'}; exit $p.ExitCode"</Path>
then save the file again as Unattend-t.xml
d) Proceed with Create and Customize virtual desktop template, and Create virtual desktop station as described on our blog at
Virtual Desktop Templates – Part
1 & Part 2
We continue to investigate why this issue occurs on some machines and not others
Issue #2: UR1 was intended to fix an issue creating virtual desktop templates on true UEFI systems, i.e. systems that don’t fall back to legacy support for earlier BIOS services. UR1 did not solve the issue. For now we are recommending
doing template creation on systems that do fall back to legacy BIOS services. To check: from Device Manager under Disk Drives select your system hard drive. Double click and go to the Volumes tab and click Populate. The Partition Style entry should
be Master Boot Record (MBR). If it is GPT you have a UEFI system.
We continue to investigate fixing this for UEFI systems.

Any word on a UEFI fix? My instructions on the other thread seem to work for me.
Also, I imagine this won't be an issue on the next version of MultiPoint Server since the next Hyper-V in Server 2012 R2 now has those native UEFI VM's. Have you guys played around with that yet? Also, FWIW, I'm not sure why the pre-release docs
mention that UEFI is only supported on Windows 8 VM's. Why not x64 Windows 7 and Vista SP1 VM's? I thought those already support full UEFI boot. Is it because Hyper-V has mandatory restrictions to have Secure Boot turned on for UEFI VM's?

Managing Monitoring Templates Based on Target Properties (not Administration Groups)

I understand how to create administration groups, based on a hierarchy of target properties. In addition, I've assigned monitoring templates to these various groups with limited success.
But I would like to be able to setup different monitoring templates, metric values, compliance configuration, etc based on the target properties themselves and not just the hierarchy.
For example, lets say I have a hierarchy of administration groups starting with "Cost Center" at the top and "Location" as the next level. Now, I want to set up some compliance rules based on Operating Systems and want to do this across all my systems, regardless of administration group. (ie all Solaris 10 machines setup one way, Solaris 11 machines another).
Can I do this?

does your RCDC info look something like the following?
<my:Control
my:Name="GroupMemberOfSG"
my:TypeName="UocListView"
my:ExpandArea="true"
my:Caption="Security Groups"
my:RightsLevel="{Binding Source=rights,
Path=isAdminAccount}">
<my:Properties>
<my:Property
my:Name="ColumnsToDisplay"
my:Value="DisplayName,Email,Domain,DisplayedOwner"
/>
<my:Property
my:Name="EmptyResultText"
my:Value="There are no groups according to the filter definition." />
<my:Property
my:Name="PageSize"
my:Value="20" />
<my:Property
my:Name="ShowTitleBar"
my:Value="true" />
<my:Property
my:Name="ShowActionBar"
my:Value="false" />
<my:Property
my:Name="ShowPreview"
my:Value="false" />
<my:Property
my:Name="ShowSearchControl"
my:Value="false" />
<my:Property
my:Name="EnableSelection"
my:Value="false" />
<my:Property
my:Name="SingleSelection"
my:Value="false" />
<my:Property
my:Name="ItemClickBehavior"
my:Value="
ModelessDialog " />
<my:Property
my:Name="ListFilter"
my:Value="/Group[(Type='Security') and ((ComputedMember='%ObjectID%')
or (ExplicitMember='%ObjectID%'))]"
/>
</my:Properties>
</my:Control>
</my:Grouping>
Anthony Marsiglia

Cannot see CCMS Monitor Templates - System is not configured

I just finished installing SAP Netweaver Trial, and I have been able to login using the SAP* and DDIC accounts.
I can see the standard tree via the SAP client GUI.
I am trying to take a look at the CCMS Monitor Sets, and I can see the standard collection of "Entire System", "Performance Overview", etc. all fine.
However, when I double-click to load any of the monitors, I see nothing inside.
No sub-trees, nothing.
I enabled "Display error nodes" and see a node that says
"NSP : System is not configured"
I have tried creating my own user, adding in profiles like SAP_ALL, S_A.System, etc.
I also notice everytime I access the CCMS Monitor Templates, there is an entry in the Syslog:
Severity: Warning
Process Type: D0
Transaction Code: RZ20
Client: 001
User: DDIC
Message ID: BYE
Description:
Database: Invalid parameter ObjTooLar transferred to database interface
Please let me know if I am missing any components, or if there is something I need to do.
Thank you.

Thanks Sunny.
That thread did indeed helped me to resolve the issue.
However, the thread did not really provide clear instructions to complete newbies like me.
For those who also have the same issue, this is what I did:
1. Execute RZ10 (Edit Profiles) via the SAP client GUI
2. Click on the menu Utilities - Import profiles - Of active servers
3. Edit the "Instance Profile" NSP_DVEBMGS00_{Your Computer Name}
Select Extended Maintenance, and select Change
4. Change the following two parameters:
alert/MONI_SEGM_SIZE from 0 to 60000000
rdisp/autoabaptime from 0 to 300
5. In the SAP MMC, right-click on NSP and select Restart
6. After restarting, login and you should be able to see the CCMS Monitor Template nodes

How to exclude UNDO and temp tablespace using monitoring template

hi,
as per MOS note id 816920.1 undo and temp tablespace is excluded from monitoring starting version 11G onwards.It says that thresholds will need to be explicitly set if undo and temp needs to be monitored
we have grid 12C implemented now with monitoring templates which sets thresholds for all tablespaces. does it apply that thresholds to undo and temp too?? we are receiving alerts for undo and temp tablespaces and we wish to disable them. We have undo tablespaces with different names in many databases as per naming conventions for that line of business.
How can i exclude undo and temp tablespaces from monitoring using grid 12C monitoring templates. is there a way through templates where i can set thresholds of permanent tablespaces only???

In EM12c, go to the 'Enterprise' menu, then 'Job', then 'Library'. There should be an out-of-the-box job called "DISABLE TABLESPACE USED (%) ALERTS FOR UNDO AND TEMP TABLESPACES" that you can run against your database targets, and that job will disable database-generated alerts.
If a previous admin has set up EM12c-generated alerts for undo and temp, then yes, a monitoring template will take care of disabling them. Either remove those alerts from the existing monitoring template and apply them to your targets, or create a new monitoring template based on one database's current settings, remove those warning/critical thresholds for your undo and temp tablespaces, and apply it to your targets.

Template creation Issue

Hi,
We have normal a user account in OEM 12c and we grant the following privilege to that user. But the user is getting "You do not have sufficient access to perform this operation" when we apply monitoring the template..
1.Assigned roles:-
EM_ALL_VIEWER
EM_PRE12CR3COMPATIBLE
EM_TV_DESIGNER
EM_USER
PUBLIC
2.Grant connect target read-only privilege
3.Resource privilege
template collection
template
report
Please help me to fix this issue and thanks in advance.

Hi,
to allow a user in Enterprise Manager to perform a specific activity, you usually need to grant a combination of resource and target privileges. In this case, I would try the following privileges:
Target Privilege: Manage Target Metrics (also included in "Operator" and "Full" target privilege)
Resource Privilege: View Monitoring Template (also included in "Full Monitoring Template")
If your target is member of one Administration Group and included in the automated monitoring template synchronization process, you could also get error Messages, if you try to apply a Monitoring template manually.
Kind regards
Tom

Monitoring Template

I created a monitoring template specifying some metric thresholds I need to monitor. Then I selected apply from the options and from the Add button I added a target to the template I created.
How can I check in the future that the particular target is associated with some X monitoring template? I couldn't see any target information saved from the monitoring template.
"Where can I check that the moniting template is holding the below targets?"

Hi,
Just to add to this, the template apply operation does apply the monitoring settings from the template to the target. However, there is no further association with the template and the target, e.g., if the template is later changed, you will have to manually re-apply the template to the target again.
If you want a real association with a template to a target such that if there is any change in the template, these changes are automatically applied to the target, then in EM12c, this can be done using administration groups and template collections. Check out the chapter on Administration groups in the EM Cloud Control Administrator's Guide 12c.
regards,
Ana

Monitoring templates and notification rules

Hello
I was able to create monitoring templates defining the thresholds I needed and create de notifications rules.
Now where can I see them being used ? How can I see the results of a template? Where do the notifications rules publish the information?
Thanks
Gonçalo Ribeiro

Hello,
I want to apply the template to a db instance and I would like to see that information on the db instance home page on the Category alerts.
Can't I do that? The templates only work if I define a notification method?
Thanks
Gonçalo Ribeiro

Data missing under J2ee monitor templates in RZ20

Hi,
We are trying to setup Central monitoring from solman,registered ccm4x and ccmsr agents poining to SOLMAN,
The J2EE monitor template does not show data related to "APPLICATINS" "LOG FILES",it is blank locally ,Is anything else required for getting the data.
Both solman and satellite system are on EHP1

Hi,
You could try the following SAP note for that:
1081694 - CCMS: Local system missing from "SAP J2EE Monitor Templates
You should also check that you are using the latest SAPCCMSR and also the latest libjmon library. See the SAP notes:
1453112 - CCMS agent and kernel: patches 2010
1033491 - CCMS monitoring for AS Java (NetWeaver2004s, 7.00)
902460 - CCMS: Agent does not display any J2EE data in RZ20

Monitoring Template Creation question

Similar Messages

Maybe you are looking for