Monitoring traffic but not use IP SLA

Dear everyone,
I have a problem. I make a leased line between ISP (Service Provider) to Customer. And customer want to monitor traffic on this link. I can use IP SLA to do it. But now, customer don't agree to open ICMP on this link so IP SLA fall
Can everyone help me to resolve it?

SNMP traps for IP SLAs are handled through the system logging (syslog) process. This means that system logging messages for IP SLAs violations are generated when the specified conditions are met, then sent as SNMP traps using the CISCO-SYSLOG-MIB. The ip sla monitor logging traps command is used to enable the generation of these IP SLAs specific traps. The generation of IP SLAs specific logging messages is dependant on the configuration of the standard set of logging commands (for example, logging on). IP SLAs logging messages are generated at the "informational" system logging severity level.
The command ip sla monitor logging traps is sometime hidden and may not show with ?, so just copy and paste in global config mode and have logging on and check if any traps are generated.
-Thanks
Vinod
**Encourage Contributors. RATE them**

Similar Messages

  • Is there any way to have an ipad wifi 3G but not use the 3G (therefore avoiding the extra data plan costs) and just use the wifi?

    i am looking to buy an ipad 2 or the new ipad (preferably 32gb) but dont want to buy the 3G version as i have unlimited data usage in my mobile phone plan, i know the wifi only ipad is generally cheaper, but i was wondering if there was a way to buy the ipad with 3G capabilities but not use the 3G and avoid the cost of paying the extra unnecessary data plan? (I know this is a really weird question but i have the opportunity to buy a 3G ipad and was curious of the possibility? any help would be greatly appreciated. cheers

    Yes to your questions.
    You can download a complete iPad User Guide here: http://manuals.info.apple.com/en/ipad_user_guide.pdf
    If you want an iPad 2 32GB it will have to be a refurb model. The only new iPas 2 is 16GB.
    What are all the differences between the iPad 3rd Gen and the iPad 2? Is the iPad 2 worth the cost savings?
    http://everymac.com/systems/apple/ipad/ipad-faq/differences-between-ipad-3rd-gen -2012-ipad-2-2011.html
    What are all the differences between the iPad 3rd Gen models? Which should I buy?
    http://everymac.com/systems/apple/ipad/ipad-faq/differences-between-ipad-3rd-gen -early-2012-models.html
    Should I Buy a New iPad? Or an iPad 2?
    http://www.maclife.com/article/blogs/should_i_buy_new_ipad_or_ipad_2
    iPad 3 vs iPad 2 vs iPad 1- Feature comparisons with iOS 5
    http://ipadhelp.com/ipad-help/ipad-3-vs-ipad-2/
    iPad Q&A
    http://www.everymac.com/systems/apple/ipad/ipad-faq/differences-between-ipad-3rd -gen-early-2012-models.html
    A Few Questions (and Answers) About the New iPad
    http://pogue.blogs.nytimes.com/2012/03/15/a-few-questions-and-answers-about-the-   new-ipad/?ref=personaltechemail&nl=technology&emc=edit_ct_20120315
    New iPad: A Polishing of the Old
    http://www.nytimes.com/2012/03/15/technology/personaltech/the-new-ipad-is-much-t he-same-only-better.html?nl=technology&emc=edit_ct_20120315
    iPad 1, 2 and New Specifications
    http://www.everymac.com/systems/apple/ipad/index-ipad-specs.html
    16GB vs 32GB vs 64GB: Which new iPad storage capacity should you get?
    http://www.imore.com/2012/03/08/16gb-32gb-64gb-ipad-capacity/
    How much content will fit on my iPod or iPhone?
    http://support.apple.com/kb/HT1867
    If you think you may get an iPad 2:
    Refurbished iPad Prices
    http://store.apple.com/us/browse/home/specialdeals/ipad
    New 16GB iPad 2 Prices
    http://store.apple.com/us/browse/home/shop_ipad/family/ipad/select_ipad2
    When iOS 6 comes out in the fall, the iPad 3 will get Siri, but the iPad 2 won't.
     Cheers, Tom

  • Can I install the creative cloud on multiple machines but not use it or pay until activate it

    I would like to install the Creative Cloud software on several machines now but not use it or pay for it on all the machines until the person using that machines needs it then they can pay to activate it.  Is it okay to have the software installed on lots of machines but not activated?

    Hi There,
    If the software is installed on the machine and it is not activated, you would not be able to use it once the trial is expired after 30 days.
    Whenever, you wish to use it, you can buy it and can start using it.
    Thanks,
    Atul Saini

  • Cannot reinstate catalog after returning PC (Windows 7) to factory settings (because of worm infection). Catalog was backed up on external drive but not using PSE backup facility. Cannot find and *.tly file. Is this hopeless?

    Cannot reinstate catalog after returning PC (Windows 7) to factory settings (because of worm infection). Catalog was backed up on external drive but not using PSE backup facility. Cannot find and *.tly file. Is this hopeless?

    If you made backups of all of your photos and your catalog file using some third-party method (i.e. not using the PSE catalog backup command), then you should be able to restore everything.
    Step 1. Put the photos in the EXACT SAME LOCATION as before. For example, if they were in subfolders of C:\Users\<username>\Documents, then they must go into the exact same subfolders of C:\Users\<username>\Documents.
    Step 2. Move the catalog file to wherever you want it to be, and then double-click on it.

  • Is there a way to purchase an app from the App store but not use the money I currently have in my iTunes account from a gift card?

    Is there a way to purchase an app from the App store but not use the money I currently have in my iTunes account from a gift card?

    The only way I know is to purchase it as a gift.

  • Corruption? - LIN_ATTACHMENT_RECORDs found but not used

    Hi,
    Since moving to GW 2014, a horrible problem has returned. We've used
    GroupWise for as many years as I can remember, and some years ago, we
    noticed on a regular basis, that emails were becoming 'corrupt' after
    GWCHECK contents scheduled maintenance jobs had been run.
    By 'corrupt', I mean we noticed numerous emails in shared mailbox folders
    (not always shared folders though) were showing as 'posted' items, and the
    header and property information was missing. Occasionally, all that remains
    is a posted note with the subject, but most of the time it's the attachments
    that are missing.
    Now, our end users rely heavily on these shared folders, and there own email
    mailboxes alike.
    I assume the part of the GWCHECK log that refers to this behaviour is
    "LIN_ATTACHMENT_RECORDs found but not used". I assume this because it
    appears in GWCHECK content check logs occasionally, and when I first noticed
    this issue all them years ago, it was present in the logs then too.
    Can anybody help me out here? What is happening, and why? I will be under
    real pressure to explain and solve this as soon as it is noticed once again
    by my end users, and I can see from the logs that it's happened 3 times
    since moving to GW2014...
    Any help very much appreciated.
    Thanks, Alan

    Hi Andy, sorry for the delay.
    This error from previous years, was attributed to something going on with
    the filesystem. However, just like back then, there is no AV or 3rd party
    product touching the GW filesystem, so I have to assume it's not that. The
    file systems is EXT3, the server was built by a consultant, so I'm not
    certain any specific tuning was done with the server. Back in the NW days,
    NSS settings were essential to optimise performance.
    The filesystem is not accessible to anyone.
    Hardware - it's a VM on VMWare, the data is on the SAN, not dedicated
    storage to the VM itself. It's the latest SP's of both SLES and GWise, as
    far as I am aware, it was built less than 2 months ago.
    The SR is open with Novell now, but they are waiting for me to try some
    things that need to be done out of hours...
    "1. Delete all the scheduled maintenance from the admin console.
    2. Wait for 10 minutes
    3. During non working hours, bring down the POA and MTA and any other GW
    agent
    4. Rename the wpcsin, wpcsout from teh PO folder
    5. Rename the wpcsin. wpcsout, MSLOCALfrom the domain folder
    6. Restart the Agents
    You can then use schedule one maintenance on the PO to check if all's well."
    I'm not sure if any of that will change things, will keep this thread
    updated though.
    Thanks, alan

  • Since Febuary 14th, 2013 we are unable to send and recieve email using our hotmail account on our Iphone. We can get our email by loggin in with our computer but not using our Iphone.

    Since Febuary 14th, 2013 we are unable to send and recieve email using our hotmail account on our Iphone. We can get our email by loggin in with our computer but not using our Iphone.

    Hotmail has been discontinued for some time now.  See:
    http://windows.microsoft.com/en-us/windows/outlook/auto-upgrade-outlook-faq

  • Creating Links to Object but not using the record id field in the web add

    Hello,
    Im trying to create a link between OnDemand an another system but the other system is the source system so it will be creating the HTML Link based on values the user selectes.
    What i am trying to do is create a link link the following:
    https://secure-ausomxdsa.crmondemand.com/OnDemand/user/ServiceRequestDetail?ServiceRequestDetailForm.Id=ADSA-73J818&ocTitle=484426-429198955&OMTGT=ServiceRequestDetailForm&OMTHD=ServiceRequestDetailNav&ocEdit=Y&OCTYPE=&ocTitleField=SR+Number
    but without "ServiceRequestDetailForm.Id=ADSA-73J818" at the end i want something like
    https://secure-ausomxdsa.crmondemand.com/OnDemand/user/ServiceRequestDetail?ServiceRequestDetailForm.SRNumber=484426-429198955&ocTitle=484426-429198955&OMTGT=ServiceRequestDetailForm&OMTHD=ServiceRequestDetailNav&ocEdit=Y&OCTYPE=&ocTitleField=SR+Number
    As this is not using the ID field, Is this possible can someone point me in the right direction on how i should start?

    Hi Jonno,
    It is not possible to use links to object without Id field. U can pass other values but Id is important- based on that only OnDemand identifies the record.
    So what i would suggest is
    1) Either use Id along with SR Number in ur source system.
    Since what i understood is u are not creating new SR so u have the Id of the SR. Along with SRNumber save Id also in the external system
    2) Or use Webservices to query with SR Number for the Id then use it in the link.
    Hope this helps.
    Regards,
    Lemu

  • Can receive mail using comcast but not using mail on ipad

    I can receive and send mail using my comcast app but can only receive mail using the mail app but not send.

    Been there and done that with the Comcast email account on my iPad. Specifically ...
    Check the outgoing mail server setting. Make sure that your username and password are in there.
    Settings>Mail, Contacts, Calendars>Your email account>Account>Outgoing mail server - tap the server name next to SMTP and check in the primary server and make sure your username and password are entered and correct - even if it says that the password is optional.

  • Error 4801, but not using Vista and have mic plugged into jack.

    Hi, i'm working on a project that involves inputing from a microphone, running it through a filter and then an FFT, and then doing some analysis on the data. For the input from the microphone, i'm having some issues. I basically drew all of the input functionality from the "Continuous Sound input.vi" example vi, which works on my computer, with a microphone and does display the signal. However, when i copied that over and modify it a little, the Sound read has either one of two errors. When i place the "Sound Clear" sub vi outside of the inner while loop, the Sound Read sub vi appears to have some sort of error relating to overflowing the buffer (i think 4822, but not 100%), no matter how low i put the samples/second and elapsed time function to exit the loop. If i put the Sound Clear sub vi INside the loop (not how it is in the continuous sound input vi, then i get error 4801, described here: 
    [\Quote]
    Error 4801 occurred at an unidentified location
    Possible reason(s):
    LabVIEW:  (Hex 0x12C1) Invalid sound task refnum.
    What steps can I take to resolve this issue?
    Solution: 
    Error 4801 is given because the sound driver in Windows Vista disables the microphone and line-input jacks when it does not detect a source plugged into the jack.  The hardware is disabled by the Windows Operating System, not National Instruments software or drivers.  This behavior is not seen on XP computers, only on Vista.  
    The resolution is to plug in a microphone or audio source to the computer.  Windows Vista will detect the microphone or audio source, and error 4801 will be resolved. 
    [/endquote]
    This seems very strange that i should recieve this error, as i am running win7, not vista, and have a microphone plugged in. The microphone jack is working - i've tested that with other programs and the continuous sound input.vi, so it works just fine. I just have no idea what to do at this point to fix the problem. My code is attached, Thanks for any assistance in advance!
    Attachments:
    project ver 2.0.vi ‏84 KB

    Hi ir0nsoul,
    Thank you for the detailed explanation of your issue. To begin, the reason you are getting the overflow error is because the number of samples needs to be 1/10th of the sample rate. Next, you need to have the Sound Input Clear.vi outside of your while loop because you are clearing the task immediately after you read, so the next time it goes to read, it won't find the stream anymore. Finally, to see if Windows recognizes your microphone, use the Acquire Sound Express VI and check the drop down menu to see if your microphone is listed (use the device ID to set the control back in the Continuous Sound Input.vi). I suggest getting your microphone to work with the Continuous Sound Input.vi first and then add you modifications later. Hope this helps!
    Aldo A
    Applications Engineer
    National Instruments

  • Link to a URL but not using popup

    I am trying to access anHTML file that loads an interactive swf file created in Flash with external links to XML and graphic files. I need to present the interactive swf file and still have access to the navigation click boxes on the slide that loads the swf file. I have tried the open URL with New selected which gives me a popup. Displaying the popup requires that the learner close the popup in order to return to the base project.
    Thanks in advance.
    tgafford

    Hi there
    You could configure the popup so that it closed at the end of the play.  But then again, you said it was created in Flash and not Captivate.
    I'm thinking that perhaps you are wanting a Frameset in the HTML, but  not sure. If you used a Frameset, you could then have navigation  occurring in one frame while what you have navigated *TO* appears in  another frame.
    Cheers... Rick

  • A plugin that is installed but not used, does it load?

    if a plugin is installed (can be found in the "about plugin" drop down menu) can it affect PS performance or cause problems even if it's not used?  does it load with PS?
    thx

    sorry I kept reading it as:
    >Yes its loaded if its not loaded ,  then you would not be able to use it.
    but it looks like you meant
    >Yes its loaded , if its not loaded , then you would not be able to use it.
    although I would think that it's similar to a script in that it often calls external code, but only after you use the plugin.

  • POC aggregated ok in CNE5 on WBSe level 1, but not used in RA calculation

    Hi all,
    I have a WBS structure with let's say 2 levels of WBSe, one WBse at level 1, 2 at level 2.
    I want  to :
    - calculate the POCs at WBSe level 2, then aggregate them at level 1, using weighted WBSe.
    - run the RA calculation for all WBSe.
    The first part is working ok with measurement methods in WBSe, weights in CJ20n on WBSe level 2 : transaction CNE1 to calculate POC, then transaction CNE5 : I get the correct POC on level 2, and the aggregated POC at level 1.
    But when I run the result-analysis calculation (KKAJ) for the whole project : POC is displayed correctly on WBSe level 2, but the aggregated POC is not used in WBSe level 1, and therefore RA results are wrong at level 1 : I always get 0 in the POC for the WBSe level 1, or sometimes 100 if I play with the OKG3 parameters.
    The only clue I have is that, in table COSR used to store the POC, on the SKF for Result-Analysis usage, I get 3 lines :
    - one with value type P1, with 0 on all the line
    - one with value type P2, with the correct aggregated POC value, Business transaction PEV1
    one exactly the same as above, but with negative values and Business transaction PEV2.
    Don't know if it is the reason for this aggregated POC nt to be used in RA calculation.
    Thank you all for any help.
    Patrick

    Did a fresh install and still having the same problem. Giving up now. Mod can now close this thread

  • Spry assets folder needed! but not using any spry widgets, help totally stressed out?

    l keep trying to set up a new site on CS 5.5 only to keep being told l need a spry assets folder, l have created my own folder named assets folder within my site folder,l have done a seperate folder ,l have looked through all files cannot find any other folders named this. l have downloaded sample files from Adobe & it still hasn't worked. What an earth can l do l'm sure its something silly as you probably guessed l'm a bit of a novice but this is driving me crazy & why do l need a spry assets folder when l'm not using any spry widgits. Any advice or solutions would be great.
    Thank You for your time.

    Whenever I set up a new site, I use a "default" setup I learned from Lynda.com.
    First a folder with the site name.
    Inside that a folder named "www"
    Inside that five folders named:
    "css" <-for stylesheets other than SpryAsset css
    "files" <- for anything that that doesn't go elsewhere
    "images" <-for all site images other than SpryAsset images
    "scripts" <-for javascript files other than SpryAsset scripts
    "SpryAssets" <-Note the capitalization and that it's all one word. DW is VERY picky about this. This folder holds Spry CSS, Spry javascripts and Spry images
    In your root folder create a folder and name it SpryAssets and DW will acknowledge it as your Spry folder.
    Some people prefer to use "styles" instead of "css". This isn't a big deal.
    Some people prefer to use "js" instead of "scripts" but if you embed a flash object, DW will create a "scripts" folder and suddenly you have two folders for javascripts, so I prefer to just have the one named "scripts".

  • CSS are included but not used

    Hello,
    I encountered strange problems using CSS in my JSP files when building a portal
    with BEA WebLogic Platform 8.1.
    I have the CSS files to be used entered in the skin.properties and they are included
    in the resulting HTML code but they are not used. At least, the texts to be styled
    appear as plain text.
    Why? What can I do?
    Many Thanks in advance,
    Dirk
    [email protected]

    Hi Dirk,
    I'd suggest that you should ask your question in the portal newsgroup
    [2]. Also, did you see this statement in the docs [1], may not be
    relevant however...
    Style classes inserted by the skeleton JSPs that do not have
    corresponding entries in a CSS file are ignored.
    HTH,
    Bruce
    [1]
    http://www.google.com/url?sa=U&start=1&q=http://edocs.bea.com/workshop/docs81/doc/en/portal/buildportals/fwPortalStyleRef.html&e=912
    [2]
    http://newsgroups.bea.com/cgi-bin/dnewsweb?cmd=xover&group=weblogic.developer.interest.portal
    Dirk wrote:
    >
    Hello,
    I encountered strange problems using CSS in my JSP files when building a portal
    with BEA WebLogic Platform 8.1.
    I have the CSS files to be used entered in the skin.properties and they are included
    in the resulting HTML code but they are not used. At least, the texts to be styled
    appear as plain text.
    Why? What can I do?
    Many Thanks in advance,
    Dirk
    [email protected]

Maybe you are looking for