More port\lines that Ni-6501 device

Hi All,
I am using Ni-6501 device.
But i need more port\lines.
What kind of device can i use to have more than 24 port/lines IO???
Please help. Thanks brothers..
Regards,
Jessie

The 6509 has 96 DIO lines. Will that be enough for you? There is a USB, PCI, PCIe, and PXI version available.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Similar Messages

MRP create more Schedule Lines than target quantity

We already follow the OSS note 83343, we create a Schedule agreeement and validity date is the same as the Source List and Quota arrangement, also the Target Quanity is the same in the quota arrangement in the maximun quantity and Maximun release qty fields.
After maintaining that data, we run the MRP as follow:
Processing key          NETCH               Net change for total horizon
Create purchase req.    2                   Purchase requisitions in opening period
Delivery schedules      3                   Schedule lines
Create MRP list         1                   MRP list
Planning mode           1                   Adapt planning data (normal mode)
Scheduling              1                   Basic dates will be determined for plann
After that, still in teh schedule agreement was created more schedule lines that the quantoty is bigger that the target quantity in the sched Agreement.
What else we miss??

Thanks for your not help.
That I can investigate is the quota arrenagement is incorrect but for some reason the QA is not working.

A barcode scanner that was connected directly to the Mac's USB port stopped working as the "USB had too much power drawn", even though it has worked for over a year in that port. WHen we plugged it into the port on the keyboard, the device works. Why?

A barcode scanner that was connected directly to the Mac's USB port stopped working as the "USB had too much power drawn", even though it has worked for over a year in that port. When we plugged it into the port on the keyboard, the device works. Why? Obviously the device is operational. Could the USB port have burned out from having too much power drawn? If so, is it reparable?

It can't draw "too much" power, it can only draw as much as the USB port is able to provide and no more. IIRC, the keyboard port has a lower power output than the iMac's port.
That being said, yea, it's possible that the port has failed and it can be replaced or if another port works you can use that one. Although if it is still under warranty or covered by Apple Care, then I would take it to an Apple Store or service provider to get the port repaired.

EtreCheck version: 2.1.5 (108) Report generated 4 January 2015 14:29:26 GMT Click the [Support] links for help with non-Apple products. Click the [Details] links for more information about that line. Click the [Adware] links for help removing adware

My Mac is very slow and applications take a long time to load, especially Safari and iTunes. Please help.    I have run the Etrecheck report and these are results.
Thanks Pat
EtreCheck version: 2.1.5 (108)
Report generated 4 January 2015 14:29:26 GMT
Click the [Support] links for help with non-Apple products.
Click the [Details] links for more information about that line.
Click the [Adware] links for help removing adware.
Hardware Information: ℹ️
iMac (21.5-inch, Mid 2011) (Verified)
iMac - model: iMac12,1
1 2.7 GHz Intel Core i5 CPU: 4-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
BANK 0/DIMM1
empty empty empty empty
BANK 1/DIMM1
empty empty empty empty
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
AMD Radeon HD 6770M - VRAM: 512 MB
iMac 1920 x 1080
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:32:50
Disk Information: ℹ️
ST31000528AS disk0 : (1 TB)
EFI (disk0s1) <not mounted> : 210 MB
Macintosh HD (disk0s2) / : 999.35 GB (717.51 GB free)
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
OPTIARC DVD RW AD-5690H
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Seagate Expansion Desk 2 TB
EFI (disk1s1) <not mounted> : 210 MB
Seagate Expansion Drive (disk1s2) /Volumes/Seagate Expansion Drive : 2.00 TB (1.66 TB free)
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. iPhone
Apple Internal Memory Card Reader
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Library/Application Support/Avast/components/fileshield/unsigned
[loaded] com.avast.AvastFileShield (2.1.0 - SDK 10.9) [Support]
/Library/Application Support/Avast/components/proxy/unsigned
[loaded] com.avast.PacketForwarder (2.0 - SDK 10.9) [Support]
Problem System Launch Agents: ℹ️
[failed] com.apple.syncservices.SyncServer.plist
Launch Agents: ℹ️
[loaded] com.avast.userinit.plist [Support]
[running] com.epson.Epson_Low_Ink_Reminder.launcher.plist [Support]
[loaded] com.epson.esua.launcher.plist [Support]
[running] com.epson.eventmanager.agent.plist [Support]
[loaded] com.oracle.java.Java-Updater.plist [Support]
[running] com.trusteer.rapport.rapportd.plist [Support]
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Support]
[loaded] com.avast.init.plist [Support]
[loaded] com.avast.uninstall.plist [Support]
[failed] com.avast.update.plist [Support]
[loaded] com.microsoft.office.licensing.helper.plist [Support]
[loaded] com.oracle.java.Helper-Tool.plist [Support]
[running] com.trusteer.rooks.rooksd.plist [Support]
User Launch Agents: ℹ️
[loaded] com.adobe.ARM.[...].plist [Support]
[invalid?] com.avast.home.userinit.plist [Support]
[running] com.microsoft.LaunchAgent.SyncServicesAgent.plist [Support]
User Login Items: ℹ️
iTunesHelper ApplicationHidden (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support]
Default Browser: Version: 600 - SDK 10.10
AdobePDFViewerNPAPI: Version: 11.0.07 - SDK 10.6 [Support]
AdobePDFViewer: Version: 11.0.07 - SDK 10.6 [Support]
DivXBrowserPlugin: Version: 2.2 [Support]
Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support]
OVSHelper: Version: 1.1 [Support]
QuickTime Plugin: Version: 7.7.3
JavaAppletPlugin: Version: Java 8 Update 25 Check version
Safari Extensions: ℹ️
wrc [Installed]
3rd Party Preference Panes: ℹ️
DivX [Support]
Flash Player [Support]
Flip4Mac WMV [Support]
GoToMyPC Preferences [Support]
Java [Support]
Trusteer Endpoint Protection [Support]
Time Machine: ℹ️
Skip System Files: NO
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 999.35 GB Disk used: 281.84 GB
Destinations:
Seagate Expansion Drive [Local]
Total size: 2.00 TB
Total number of backups: 78
Oldest backup: 2013-07-28 18:09:06 +0000
Last backup: 2015-01-04 14:29:38 +0000
Size of backup disk: Adequate
Backup size 2.00 TB > (Disk used 281.84 GB X 3)
Top Processes by CPU: ℹ️
      2% WindowServer
      1% mds
      0% fontd
      0% mds_stores
      0% com.avast.daemon
Top Processes by Memory: ℹ️
120 MB Safari
112 MB com.avast.daemon
94 MB com.apple.WebKit.WebContent
56 MB spindump
52 MB mds_stores
Virtual Memory Information: ℹ️
479 MB Free RAM
1.56 GB Active RAM
1.11 GB Inactive RAM
904 MB Wired RAM
5.37 GB Page-ins
75 MB Page-outs
Diagnostics Information: ℹ️
Jan 4, 2015, 01:57:18 PM Self test - passed
Standard users cannot read /Library/Logs/DiagnosticReports.
Run as an administrator account to see more information.

patbythesea wrote:
Can I assume that with my Mac I do not need any additional virus protection software? If I do, what should I use?
See my Mac Malware Guide for help on protecting yourself from malware. You generally don't need anti-virus software.
(Fair disclosure: I may receive compensation from links to my sites, TheSafeMac.com and AdwareMedic.com, in the form of buttons allowing for donations. Donations are not required to use my site or software.)

AVG says your server messed up my Verizon Yahoo email. The line that reads delete, move, not spam, more...does not load. I can see my email, I just cannot open

I just spent over 5 hours in computer share with AVG. They said your server messed up my email account. I can get to my email account, but the line that reads "delete, move, not spam, more" never loads...therefore, I cannot delete email or anything else. My email account is at verizon yahoo. I need access to my email for various reasons, one of them being I pay many bills online and my email account is where I get certification that the payment went through!! My email will work through IE, though. I do not want to utilize IE to see my email...I use Firefox for everything and it would be a pain in the butt to have to switch to IE to access my email. Not to mention, I loathe IE--it's like using WEBTV! It's soooooo slow.... [email address removed, please do not post sensitive information in a public forum] is my email...

Did the support person have you do the usual:
When you have a problem with one particular site, a good "first thing to try" is clearing your Firefox cache and deleting your saved cookies for the site.
(1) Bypass Firefox's Cache
Use Ctrl+Shift+r to reload the page fresh from the server.
Alternately, you also can clear Firefox's cache completely using:
"3-bar" menu button (or Tools menu) > Options > Advanced
On the Network mini-tab > Cached Web Content : "Clear Now"
If you have a large hard drive, this might take a few minutes.
(2) Remove your Yahoo.com cookies (save any pending work first). While viewing a page on the site, try either:
* right-click and choose View Page Info > Security > "View Cookies"
* Alt+t (open the classic Tools menu) > Page Info > Security > "View Cookies"
In the dialog that opens, you can remove the site's cookies individually.
Then try reloading the page. Any improvement?
In case one of your extensions is involved, could you test the page in Firefox's Safe Mode? That's a standard diagnostic tool to deactivate extensions and some advanced features of Firefox. More info: [[Troubleshoot Firefox issues using Safe Mode]].
You can restart Firefox in Safe Mode using either:
* "3-bar" menu button > "?" button > Restart with Add-ons Disabled
* Help menu > Restart with Add-ons Disabled
Not all add-ons are disabled: Flash and other plugins still run
After Firefox shuts down, a small dialog should appear. Click "Start in Safe Mode" (''not'' Reset).
Any difference?

More ports to forward

I have a linksys WRT54GS wireless router which is working splendidly. However I play a *lot* of video games and I like to host games when playing all of these games. So, naturally, I have to forward a couple ports because not everything works happily together when hosting. I have no problems with that, I got my computer on a static IP address and all of the games I've set my router up for work just fine.
Problem is there simply aren't enough places for me to specify all the ports I want to forward. Obviously I don't want to include ports I don't need forwarded so I don't want to skip over ones I don't need. But 10 slots isn't enough... Battlefield Vietnam takes up 7 on its own. Is there any way to include more ports I want to forward?

Man, oh man, I could use more than 10 port forwarding lines! Would Linksys possibly consider increasing this to 20 in a subsequent firmware upgrade? 20 would probably be the most I would ever need.
I'm not comfortable using 3rd-party firmware upgrades on my router...
Thanks a lot for your consideration.
Dan

Need more Ports!

I have a wireless WRT54GS Router but I need more ports in back to connect other rooms(wired). What is the device that I need?

Go out and buy a 4, 8 or 16 port switch. Plug it in and you have your extra ports.

Cisco Prime: Event Larm Port 'x' is down on device.

Hi,
I'm writing regarding; event-larms; that is reporting from Cisco Prime; connected to controller. Interfaces is reporting via event-larm; that they are down.
"Virtual Domain: ROOT-DOMAIN
PI has detected a change in one or more alarms of category Controller and severity Critical in Virtual Domain ROOT-DOMAIN.
The new severity of the following items is Clear:
1. Message: Port '3' is down on device '10.1.1.2'.
(6 times)
2. Message: Port '4' is down on device '10.1.1.2'.
(6 times)
3. Message: Port '5' is down on device '10.1.1.2'.
(6 times)
4. Message: Port '6' is down on device '10.1.1.2'.
(6 times)
5. Message: Port '7' is down on device '10.1.1.2'.
(6 times)
6. Message: Port '8' is down on device '10.1.1.2'.
(6 times)
E-mail will be suppressed up to 30 minutes for these changes."
Is there a solution how to not recieve those event-larms? The only LACP interfaces that is configured is 1 & 2, in a group.
See attached screenshot, when trying to disable the other interfaces.
The LACP is enabled and configured on "management" interface.
Best Regards,
David

From: https://supportforums.cisco.com/discussion/12077376/prime-infrastructure-alarm-port-down#comment-9405836
"As far as I understand the error message you only need to disable SSO before you can disable the LAG ports."
"(Cisco Controller) >config port adminmode 3 disable
Blocked: Lag is enabled. Disabling the lag port is blocked when system is in redundancy state (SSO)"
"I would suggest to do this only in a maintenance window."

I have a thin black line that appears on my iPad screen. Is my iPad defective?

I have a thin black line that appears on my iPad screen. Is my iPad defective?

It could be having issues. If that line appears across apps(as in in more than one app, and even when you're not in an app) , try resetting the device by holding down the home and sleep key, past the power down slider, and until you see the silver apple. Let it reboot and see if the line persists. If it does, your next stop should be the apple store and let them take a look at it. Issues with the display like that are often beyond simple user fixes.

My USB ports will not recognize any devices, iPhone or external drives. Keyboard and printer work, any suggestions?

My USB ports will not recognize any devices, iPhone or external drives. Keyboard and printer work, any suggestions?

I'd start by looking in system profiler.
the blue Apple icon > About this Mac > More info...
goto the hardware section. Scroll down and click on USB
See what happens when you have the device plugged in & not plugged in.
Move keyboard & mouse around to verify that ports work. Plug device in a port that worked with keyboar or mouse. Keyboard usb ports are rather low power.
Perhaps device is taking too much power. Are devices power or unpowered? Try connecting devices to a usb hub.
Which mac do you have?
What iMac do you have?
Report system info
Blue apple > about this Mac
click on more info
click on hardware
do not copy your serial number

HT4101 What does it mean when it says that the USB device requires too much power?

What does it mean when it says that the USB device requires too much power, when using the ipad lightening pin camera connection kit?

Just that. The iPad allocates a certain amount of power to that port. If the device you're trying to plug in wants more than the iPad is willing to give, it'll trigger that warning.
If it's something that you just must hook up you can try using a powered USB hub, but results are mixed at best.
What are you trying to hook to your iPad?

My 120GB IPod classic is not recognized by my Windows 7 PC. When I plug the ipod into my computer I receive a message saying that the USD device is not recognized.

My 120GB IPod classic is not recognized by my Windows 7 PC. When I plug the ipod into my computer I receive a message saying that the USD device is not recognized. The Device Manager lists it as an Unknown Device. I've tried uninstalling iTunes and reinstalling it, but it had no affect. The odd thing is that our other iPod (160 GB Classic) is recognized on the same computer using the same USB cable. When I plug the ipod in question into another PC, the PC seems to recognize the iPod and lists it in Windows Explorer (iTunes is not installed on this machine). There seems to be something out of wack with this PC/iPod combo. Any thoughts on what I can do to try to resolve this issue? I tried all of the steps listed here, but they didn't help me. http://support.apple.com/kb/TS1538
Any help would be greatly appreciated.

Are you plugging the iPod into a high powered USB 2.0 port on the back of your PC? Have you tried a different USB cable?
What happens if you try to reset the device with it still connected to the PC?
How to reset iPod
Has this iPod ever worked on this PC or is this the first time you have time you have tried connecting it?
Have you carefully worked through each and every single suggestion in this Apple support document?
iPod not recognized in 'My Computer' and in iTunes for Windows
B-rock

How do I add more ports to my new Airport Extreme?

How do I add more ports to my new Airport Extreme? What do I need to buy?

Thinking to leave as is for now- one 2013 extreme.
That would certainly keep things a lot simpler.
Does it seem right that using speed test I'm getting similar speeds, no matter if I'm connected via wi-fi, or Ethernet?
A very good sign assuming those speeds are reasonably close to the your plan offered by your ISP. The Extreme itself is capable of much faster speeds than your ISP can ever hope to provide.
I'm thinking that all the speed in the world is not going to change Time Warner Cable, the provider for earthlink cable
Not sure what you mean here. Time Warner provides various plans, some up to 50 Mbps. I get 60+ consistently with this plan. I had a 30 Mpbs plan before that consistently delivered about 35-36 Mbps.
The math is simple. If you download a lot of files from the Internet, a 50 Mbps connection is going to take half as long to download a file as a 25 Mbps connection, for example.
One word of caution though....if you try a higher speed plan...plan to stay, as you will never go back to slower speeds once you have sampled higher speeds. Comcast now owns Time Warner by the way. I don't know whether that will be a good thing or a bad thing.

I need to cancel a line that is no longer used but I'm told that, since I transferred an upgrade from the unused line, the contract on the unused line was extended by two years. If I need to cancel both to get out of this, so be it but I'd rather not and

I'm paying for 2 smartphone lines when only one is in use. It's a waste of money that I can no longer afford. I would like for someone to present me with options or I will have to seek an alternate service provider.

Ok so now there are presumptions of both my ignorance and my dishonesty. This has become the most surreal conversation I've had in some time. I've been a VZW customer for over 10 years and no, this is not something I've ever done before. In the past, if I wanted a new phone before my 2-year deal was up, I paid full price for the phone and kept living. That's how the system works, right? In this instance, I had two lines on my account, each with different contract end dates. The secondary account was 6 months out-of-contract and unused but, for personal reasons, I kept the line in force. The person who used the account setup another account with VZW with another phone. But I kept the line active, just in case.
In the meantime, when reviewing my account online, I noticed an option on the secondary account of "Transfer upgrade". Given my understanding of the definition of the word "transfer" as well as my previous dealings with VZW phone upgrades, it seemed logical that, since both phones were under the same master account, the upgrade with its requisite contract extension would apply to the line that actually used the upgrade eligibility. It was therefore, my expectation that the primary line would either have two years tacked on to its current end date or, at the very least the contract end date for the primary line would be 2 years out from the date the upgrade was exercised. Both options were acceptable to me since, at that point, I was not considering the termination of my relationship with VZW. I knew I needed a phone with more battery life than the one I had and carrying one of those battery charge packs around wouldn't work for me. So, I clicked the transfer upgrade button on the secondary account. I then saw the primary account show as eligible for an upgrade. At that point, I upgraded the phone on the primary account. There was no point where I was notified of a 2 year extension on the secondary account and, once I clicked the "Transfer upgrade" link, there was no mention of or reference to the secondary account.
I'm not sure of who I'm replying to or where they are from so I cannot speak to the people they encounter on a day to day basis. I have not stated nor do I have any desire to get away with a free early upgrade. It should be noted that we are discussing a discounted upgrade, not a free phone. I still paid $150 for the phone and was happy to do it. However, this idea that I'm trying to circumvent the system is offensive. I'm not trying to get away with anything. As I've said in previous posts, I expected to burn discounted upgrade eligibility on the primary line for a minimum of 2 years. I actually expected the new contract end date to be 3 years away, which would have been more than fair for all concerned. Fairness, it seems, is running in short supply.
If all you have to say is that I'm stupid, ignorant, or dishonest, please don't bother to reply. If you can in some way help to bring this to a satisfactory resolution, I'm all ears. Can you hear me now? Good.

Is it problematic to use Microphone.getEnhancedMicrophone() more than once on the same device?

Here's an interesting little experiment:
     Alert.show((Microphone.getEnhancedMicrophone() == Microphone.getEnhancedMicrophone()).toString());
     Alert.show((Microphone.getMicrophone() == Microphone.getMicrophone()).toString());
They both show "false", even though the calls to getMicrophone() and getEnhancedMicrophone() always point to the same device.
I'm making an R&D app right now, and this is a potential problem for me. I've designed the app around it being able to refresh the list of available mics, and for the user to be able to go back and forth between different mics and be able to hear themselves, among other things.
If they turn on loop back for a mic, then re-select the same mic, it'll create a different object for that same exact device, and after turning off loop back for the previous instance (and removing all references to that instance), it'll turn on loop back for the new instance. The problem? It's hard to tell for sure, but there appears to possibly be some sort of issue with the Flash Player taking a minute to garbage collect the old instance, and during that time, the Flash Player trying to read audio out of that device and loop it back twice, as opposed to once.
It's hard to tell whether this is really happening, or whether the distortion I'm hearing is purely two-second transition from one instance to the other, but there are also questions in my mind about the viability of just trying to track each individual device in a Dictionary; if multiple devices have the same name and keep getting pulled out of one port and plugged into another, there seem to be problems in being able to keep track of indivdual devices very well in that case.
So is this a really big issue for an app that's designed to let people keep switching mics back and forth, as well as letting them refresh the list of available mics over and over? Or as long as setLoopBack(false); and setSilenceLevel(100); are called on every instance before its references are removed, will there not be any sort of disturbance in future instances' audio (or any other issue, aside from late GC)? Thanks!

You're creating a reference. The constructor that runs factorizes some other classes into your object such as flash.media.SoundTransform. Due to instantiating a "new" SoundTransform, it differs from the other mic references SoundTransform. Thus the object is not identical. The debug panel shows you easier:
If you really just want to see if it's attached to the same device, simply compare the index value.
if (mic1.index == mic2.index) {
     // same audio recording device

More port\lines that Ni-6501 device

Similar Messages

Maybe you are looking for