More than 1 set of scratch disks ?

i want to have more than 1 set of scratch disks in FCP.
is this possible ?
i want to have one project on one and then one on another,if so how would i save to each one ?
thanks
adam

I do this regularly as I have 2 additional hard drives in my machine. I set scratch disks on each one (for example name FCP doc on HD-1, FCP doc on HD-2). I have the corresponding FCP project on each HD. When they are long weddings, that helps me keep everything organized.
The downside is when you start up each project you have to go into FCP System Settings EACH time to make sure the scratch disks are set to the HD you want. A pain if you are switching back and forth between projects quite a bit.
Actually, each project saves in the scratch disks under its own name, so it is kind of 'what's the point' of putting on different scratch disks? I say that, then I do it Old habits die hard.
Sharon

Similar Messages

I have 2 hardisk,so i want to set two scratch disk but i doesnt work

i have 500g and another 160g hardisk.
such as i set up scratch disk in d: drive in 500g hardisk and f: driver in 160g hardisk
but i have found photoshop just use d: driver as scratch disk ,and never use f: driver.
why?

Okay! So you want to RAID your Scratch Disks! I've not tried that, and I don't know how Photoshop would handle a RAID Scratch Disk; I'm afraid someone smarter than me will have to visit the thread.
But even it were possible, both disks would have to be the the same size/capacity, speed, and cache; you can't RAID different sized disks like the ones you have, so you'd either have to have 2x 500GB, or 2x 160GB drives to start with, plus a dedicated RAID card to do the processing for you, you wouldn't want your CPU to be handling that load as well as everything else, the drives would also need to be internal as well, not an external RAID enclosure, where the I/O port becomes a bottleneck.
If you can, change the name of your question, "I have 2 hardisk, so I want to set two scratch disk but it doesn't work," to something like, "Need to RAID Photoshop Scratch Disks!" and hopefully someone who knows a LOT more about Photoshop and RAID than me will be able to give you an answer.
Also, please give as much information about your system as possible, what Operating System are you running, is it 32 or 64 Bit, Processor type and speed, installed RAM, Motherboard (some support RAID natively) etc.
Good luck!
Paul

Set New Scratch Disk for rendering...

I finished a short film on a HD with no space left at the moment. To render the video, I'll need to set a new disk to render to, but everytime I set the scratch disks to my main drive (plenty of space left, I'm desperate) and checked the render video and audio boxes, and unchecked them on my old HD. It's a pretty messy project with files everywhere, truly unorganized. But I need to set the render folder on my main one and it is still referring to my other drive when I try to render anything, which does not have enough space left to render anything. Any solutions?
So far I've tried restarting FCP and that's it.

When you go back to your System Preferences settings, you can see your main disk as scratch disk or you see your old setting to the external one?
Try trashing your FCP preferences and setting everything again.

Where do I set the scratch disk in FCP X?

I'm new to FCP X. How do I set the location of my scratch disk?

Thanks, Tom! Found both options there (see Screen Shot).
Weirdly, though, if I now try and select any of the Events now located in my other hard drive, they do show up in the Film Strip area (to the right of the Event Library), but none of these Events show up in the Time Line window (lower section). The only one that continues to show up in the Time Line window are the Events still located in the startup drive.
Is there a way to get those Events now in the other HD to show up in the Time Line window?

Set Illustrator scratch disk via scripting?

I'm using jsx scripts and ScriptUI with Illustrator CS5, and would like to give my user a way to specify the scratch disk to use. I can't find any information about accessing this preference item via scripting. Anybody know if this can be done?

Is there a way to enumerate all the available items it supports?
no, you have to open the AIPref file and have a look to see if there's something in there.
Also, it is usually not recomended, but sometimes it gets the work done, it depends on the rest of your code. You could use "SendKeys" in VBS or similar in AS, it simulates keystrokes. So in Windows I would use
- Alt+E
- N
- P
to bring up the Preference Dialog, then
- R or
- S
to get to the scratch disk options
I have a working sample here
http://forums.adobe.com/thread/942075?tstart=0

Why do people set their scratch disk to a RAM drive?

From what I've read, the scratch disk in Photoshop is there so that if you become low on RAM, it will move data from the RAM to the allocated scratch disk...so why bother making that scratch disk the RAM when it'll just be going from the RAM...to the RAM? Am I missing something here?

Siderz95 wrote:
From what I've read, the scratch disk in Photoshop is there so that if you become low on RAM, it will move data from the RAM to the allocated scratch disk...so why bother making that scratch disk the RAM when it'll just be going from the RAM...to the RAM? Am I missing something here?
They're the ones missing something. It doesn't help to swap RAM to RAM. Now, it's possible people are talking about pointing their TEMP area to a RAM drive. There could be merit in that, but...
You want a real leg up? Get a good SSD for scratch, or take it even further and run your entire system off an array of SSDs.
-Noel

How do I make Lion Server support more than one Time Machine disk?

Under Snow Leopard Server, I had two disks set up for Time Machine backups. This came about as I'm running a Mac Mini with the 500 GB internal drives which turned out to be insufficient for one of the connected Macs which uses a terabyte drive. I then added an external 6 TB drive and made it a Time Machine destination too. Worked beautifully. When I upgraded to Lion Server the external large drive was no longer available for backups and the interface for configuration within Server only allows for one drive to be in use at a time. Any suggestions (short on reverting to Snow Leopard) as to how to re-enable having both drives available for networked Time Machine access?
Thanks!

Hi Adam,
Before I even realised that the Server app had a setting for TM, I just configured TM backups on my (SL) clients as I had done in SL.
I shared the drive(s) on the server I wanted to use.
For each client, I mounted the appropriate shared drive containing its sparseimage file, then set TM on the client to use that drive.
Then I unmounted the shared drive and started TM.
It mounted the remote drive (without displaying it in Finder) and opened the sparseimage, showing the "Time Machine Backups" volume on the desktop.
So you could use any drive attached to the server to backup any client.
It worked fine for me.
In the end, I changed my clients to use the (single) shared "Backups" volume which Server.app creates because I can fit all my stuff on one drive.
HTH

Cannot see more than one shared virtual disk at a time

I have multiple virtual disks configured and as I add them to the specific virtual machine im using it modifies the vm.cfg as follows:
disk = ['file:/OVS/running_pool/110_openfiler/System.img,hda,w',
',hdc:cdrom,r',
'file:/OVS/sharedDisk/openfiler-ocs-u01.img,hdd,w!',
'file:/OVS/sharedDisk/openfiler-ocs-u02.img,hde,w!',
'file:/OVS/sharedDisk/openfiler-SAN-test.img,hdf,w!',
when the machine boots up the contents of /dev only contains the shared drive hdd, thus I cannot see hde or hdf.
One thing I tried was to edit the vm.cfg after adding the shared drives to the machine to mimic:
disk = ['file:/OVS/running_pool/110_openfiler/System.img,hda,w',
',hdc:cdrom,r',
'file:/OVS/sharedDisk/openfiler-ocs-u01.img,sda,w!',
'file:/OVS/sharedDisk/openfiler-ocs-u02.img,sdb,w!',
'file:/OVS/sharedDisk/openfiler-SAN-test.img,sdc,w!',
This allows me to see all three drives when I issue fdisk -l
Disk /dev/hda: 105.2 GB, 105226698752 bytes
255 heads, 63 sectors/track, 12793 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/hda1 * 1 13 104391 83 Linux
/dev/hda2 14 12539 100615095 83 Linux
/dev/hda3 12540 12793 2040255 82 Linux swap / Solaris
Disk /dev/sda: 20.9 GB, 20971520512 bytes
255 heads, 63 sectors/track, 2549 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 2550 20480000 ee EFI GPT
Disk /dev/sdb: 20.9 GB, 20972569088 bytes
255 heads, 63 sectors/track, 2549 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 1 2550 20481024 ee EFI GPT
Disk /dev/sdc: 104.8 GB, 104857600512 bytes
255 heads, 63 sectors/track, 12748 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdc1 1 12749 102400000 ee EFI GPT
but then my question becomes... could this cause any potential problems?

I found that there are 4 IDE disks and 7 SCSI disks at most for HVM guest on Oracle VM 2.1 version. For IDE disks, The available disknames are from hda to hdd; and for SCSI disks, are from sda to sdg. you may make test about it. :)
Message was edited by:
Changhai

Setting pref file so FCP prompts Scratch Disk Reset

I was told by a fellow poster that "you can lock the pref file (or set permisions) so that FCP can't save the selected Scratch Disk location ... this will force FCP to ask you to set the Scratch Disk location everytime it launches."
Does anyone know how to do this?
Please take me through step-by-step.

if a fellow poster told you then why don't you do a search mate?
basically, you can either just lock the file just by locking it in the finder (use Get Info) or you can set the privilledges so that the file is read only.
step by step is here:
http://discussions.apple.com/thread.jspa?messageID=5167687&#5167687

Photoshop Elements 2.0 Windows 7 Scratch Disks Full

Hello there,
I have seen a few posts about PSE2 on Windows 7, but none of them have helped get it working for me. Same deal, I run PSE2 and get the "Scratch disks full" message. I have a 1.5GB hard drive. I have tried everything and no luck on getting it working. Any new ideas would be greatly appreciated!
Thanks

Here are some of the things i've had success with in older versions of photoshop (pse 2 or ps 7 and older versions) with hard drives bugger than 1tb.
The first two always work
1. Install windows xp mode if your version of windows 7 supports it.
2. Install an older operating system on vmware or virtualbox.
3. Run pse 2 as an administrator and press the Alt+Ctrl keys just after starting pse 2, and then set the scratch disk to the recovery partition on your hard drve.
4. add a second hard drive to use as the scratch disk for pse 2
5. Partition a part of your existing hard drve to use as the scratch disk for pse 2
6. Re install windows 7 on partition of 1tb and then partition the rest of the 500mb for storage of files
Added: You always have the option of buying photoshop elements 10 which has no problems with hard drives bigger than 1b.
Message was edited by: R_Kelly

Premiere pro cs 4 defaults scratch disks to C Drive

Hi, I have this peculiar problem only with Premiere Pro CS4.
When setting the scratch disks on any drive other than the C drive, they always default back to the C drive.
This does not happen with CS3 or previous.
Premiere creates directories on the selected drive (other than C) but it dumps the preview files back on C, while the newly created directories remain empty.
This happens both on AMD and Intel machines, on windows vista ultimate.
Any thoughts?
Thank you
Louis

Where is your project (prproj) file?

How to add scratch disks to adobe illustrator CS5?

I am trying to set up scratch disk on illustrator but my only options are startup for the primary and macintosh hd for the secondary. I have a time machine set up for wireless backups and even tried connecting to it via USB and I still cannot assign it as a scratch disk.I keep getting the warning "cannot complete because not enough memory(RAM). I installed more RAM and now I am trying to set up scratch disks. Anyone know whats up?

Will the Airtight template let you put in a separate caption for EACH photo, or just one caption that goes on every single slide?
What third party software would let me add captions...I need something fairly easy to use.
Thanks!

Different Scratch Disk Per FCP Project

I love FCP Studio and swear by it for most things. I'll cut straight to the point...
I want to be able to set my scratch disk location (capture scratch, render files, audio render files) as a project based setting NOT a system wide setting, and I want FCP to remember this setting for each project.
I am very frustrated with the fact that you can't set the scratch disk to different locations per project, as I am constantly changing the location depending on what I am working on, and sometimes I forget and I'm working off the wrong drive.
Also, sometimes I'm multi-tasking and working on two or more projects for different clients off of different mobile drives. This becomes a big cluster f$!k when I'm forced to render and digitize everything to one drive yet I'm working off of several removable drives that I need to take with me at some point. I need elements for each project to stay on their own drive!
Now, I understand that my need goes outside the real of the normal editor, and may actually cause a larger fundamental back-end issue that I am not aware of, but is it asking too much to have the scratch disk setting a project based setting, and not a system setting?
It seems to me that FCP could just remember where you want to point your files to depending on what project you are working in?
Any ideas? Am I missing an obvious solution? Any 3rd party software out there to help with this?

Matthew Lynn wrote:
... It seems to me that FCP could just remember where you want to point your files to depending on what project you are working in?...
You would think ...
I completely agree and have posted about this on many occasions.
You might find this an interesting read:
http://discussions.apple.com/message.jspa?messageID=10916404#10916404
I absolutely love the ability to set different drives for different file types if we choose.
But it should be a PROJECT setting not a System wide preference.
This thread is just another example of why it should be that way.
Send a suggestion to Apple http://www.apple.com/feedback/finalcutpro.html
Hey, ya never know.
best,
g

Scratch disks and RAM usage

i would like to understand the relationship between scratch disks and RAM usage in Photoshop.
While i was working on a fairly big psb file (2gb), photoshop kept prompting that I was out of memory, but in fact the utilization was only 75% (i had 16gbs total, photoshop was only using 7gb, and i allowed PS to use up to 14gb in total). when it says out of memory, it was actually my scratch disk at fault ( i only set 1 scratch disk, which was my 120gb SSD running out of space).
any idea how I can optimize PS to use up all my RAM first before even touching my scratch disk? (short of using a RAMdisk, please).
thanks!

I am curious about this also. I just reinstalled W-7--have 11 G of physical memory--a ton of hard drive empty space also, and I have been wondering why PS_CC is so slow--since basically I have only put my Security and Browser in addition to Adobe back on the Dell XPS computer..... At least now it does show the downloading percentage (like .psd file) , but that must be what is happening. I do think that some of these "frozen" screens I have been experiencing, was because the program was using scratch disk, instead of the Ram... I came up from CS-5, and can't describe it in detail, but just realize how slow PS-CC is in most everything. Going back and see if reallocating will help...

How can i make my external hard drive be the scratch disk with 1 FW input?!

Hello! I use firewire with my external HD AND my camera...however i only have one firewire input...i set my scratch disk for final cut to work with my external HD but when i am importing footage to my computer with my camcorder, i can not have my external HD plugged in, thus the scratch disk has to be set to something else to continue working. So how can i work around this problem?! Should i just change the settings back after i import the footage and it all goes to place?

I don't understand the need to daisy chain. I have one Firewire port on my MacBook Pro, and I use a Firewire hub. I've been connecting two 1TB Western Digital My Book Studio Edition hard drives (one for FCE and iMovie projects; one for the media files I create via export), and a Canon NTSC ZR200 miniDV tape camcorder, or a Sony Digital8 tape camcorder, or sometimes a Canopus ADVC 110, without issues. Why not use a Firewire hub? . . . except to save the small expense.

More than 1 set of scratch disks ?

Similar Messages

Maybe you are looking for