Mountain Lion only boots into Recovery mode after using iCould lock

Hi everyone!
I have searched the forums for hours now, but I can't seen to find an answer to my question, so I'd like to ask it.
Recently my system partition failed due to frequent kernel panics caused by a cable in the screen I think. The kernel panics still occur, but I don't know what to do with them.
I managed to save my files and reinstall my osx, which is Snow Leopard (the disc came with the computer). Then I wanted to install my purchased copy of Lion through Appstore, but it said it's no longer available in my country and I couldn't download it again.
Then I decided to buy a copy of Mountain Lion which I tried to install. I managed to do it, and I tried to explore my new operation system.
I tried the iCloud app as well, including the Lock. It locked the computer, and rebooted, but ever since I couldn't unlock it.
When it asks for the password I enter it and it accepts it, but doesn't unlock, only lets me into Recovery mode. Now I reinstalled the whole thing over again and when the Mountain Lion install finishes, it only boots into the Recovery HD without asking.
So if I reboot my computer, no matter what I do it only boots into Recovery Mode.
Please help!!
Mike

I was afraid the Apple Store wasn't going to be an option.
Based on your previous post, I was under the impression you could download Mountain Lion, but when you installed it, it locked up again. Not true?
I don't know how to remove it. You can try contacting Apple support through the link below to see if they can help you get this unlocked.
Apple Support Contact
Are the kernal panics new since all this happened?
Here is some information about kernal panics.
Kernel Panics - About
Kernel Panics - Avoiding and Eliminating
Kernel Panics FAQ
Kernel Panics FAQ (2)
Kernel Panics - Understanding and Debugging
The articles discuss where kernal panic reports are filed. After you have a kernal panic, copy the report and post it here. Please copy and paste rather than using a screen shot. There are several people who can read them and they can suggest what to do next. Reading kernal panic reports isn't something I've totally figured out yet.

Similar Messages

My MacBook won't boot into recovery mode after new hard drive installation. Please help!

I just installed a new hard drive. On boot it keeps on going to the flashing folder with a question mark inside.
I was able to format the new hard drive but am unable to boot into recovery mode to install the operating system over the air.
When I hold down Command -R it keeps on taking me to the flashing folder.
Please help!

A new hard drive doesn't have a recovery partition. It's totally blank.You're going to need either your original install discs or a Snow Leopard retail disc from which partition, format and install OS X.

MacBook Pro OSX 10.9- Cannot boot into recovery mode or use USB bootdisk

Hi guys,
I'm having an issue with my MacBook Pro running OSX 10.9. I want to re-install the operating system, however the computer freezes when being booted into recovery mode or when rebooting into a USB boot disk. Either the spinner freezes or it moves to a screen with just the Apple logo.
Thanks in advance

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Click the Clear Display icon in the toolbar. Then try the action that you're having trouble with again. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.

Mountain Lion installer boots into recovery partition

Strange thing: being a registered devloper I downloaded the OS X Mountain Lion (10.8.2) installer and wanted to upgrade one of my Mac minis (which was running 10.7.5).
However, the aluminum mid-2010 Mac mini acts strange: I copied the installer onto a USB stick and burned it onto a DVD, too. Tried to install from both media but the Mac mini boots either into the Mountain Lion recovery partition (so that was somehow created) or the Setup assistant lacks entries in lists and always jumps to step 1 after step 3 or 4 in an endless loop.
Once -- when I wanted to select the 10.8.2 OS X as boot volume -- I got an error message that boot caches can't be created so I can't set this partition as boot partition.
I've got app. 100 GB free on the Mac minis hard disk.

I was afraid the Apple Store wasn't going to be an option.
Based on your previous post, I was under the impression you could download Mountain Lion, but when you installed it, it locked up again. Not true?
I don't know how to remove it. You can try contacting Apple support through the link below to see if they can help you get this unlocked.
Apple Support Contact
Are the kernal panics new since all this happened?
Here is some information about kernal panics.
Kernel Panics - About
Kernel Panics - Avoiding and Eliminating
Kernel Panics FAQ
Kernel Panics FAQ (2)
Kernel Panics - Understanding and Debugging
The articles discuss where kernal panic reports are filed. After you have a kernal panic, copy the report and post it here. Please copy and paste rather than using a screen shot. There are several people who can read them and they can suggest what to do next. Reading kernal panic reports isn't something I've totally figured out yet.

Macbook only boots into recovery mode

Any help on this issue would be greatly appreciated. The other day I was watching a movie on Quicktime and out of nowhere the computer froze up. I waited a minute and then finally just did a force shut down of the computer. I then started it back up but instead of coming to the login screen, it started up in recovery mode, where I get the OS X Utilities window.
I opened disk utility where instead of the normal Macintosh HD listed on the sidebar, it says "disk0s2". I tried repairing the disk and it came up with an error saying it couldn't be repaired and I have to reformat the disk. I took it in to the genius bar and they ran a battery of tests on the hardware and it all came back fine, so he told me it must be a software corruption issue.
Now I could just reformat the disk, but being the idiot that I am, I haven't done a Time Machine backup in several months, so there's files I would really like to recover before going through with the reformat. The guy at the genius bar seemed to think it wasn't recoverable, even by a data recovery company, but he said there's always a chance. Is there a chance? And is there anything else I can try to do at home? I've heard good things about Disk Warrior, but how would I run it if I can't even get to my desktop? From another computer?
I have a 2013 Macbook Pro, retina display, 256GB SSD, 8GB memory, running Mavericks.

I was afraid the Apple Store wasn't going to be an option.
Based on your previous post, I was under the impression you could download Mountain Lion, but when you installed it, it locked up again. Not true?
I don't know how to remove it. You can try contacting Apple support through the link below to see if they can help you get this unlocked.
Apple Support Contact
Are the kernal panics new since all this happened?
Here is some information about kernal panics.
Kernel Panics - About
Kernel Panics - Avoiding and Eliminating
Kernel Panics FAQ
Kernel Panics FAQ (2)
Kernel Panics - Understanding and Debugging
The articles discuss where kernal panic reports are filed. After you have a kernal panic, copy the report and post it here. Please copy and paste rather than using a screen shot. There are several people who can read them and they can suggest what to do next. Reading kernal panic reports isn't something I've totally figured out yet.

Brand new Mac mini only boots into recovery mode...

I just picked up a brand new mac mini a couple of hours ago and right from the start, it asked only for a language perference and then after that having been selected, promply went straight to the OS X Utilities screen.
I cant seem to get it out of this mode. And because I do not have an internet conncetion set up on it, I can't, for example, re-install anything or restore or...
It's basically a boat anchor right now.

Startup holing the Option key and see if the Startup Manager will allow you to select the Macintosh HD.
see > Startup Manager: How to select a startup volume
If not, then return it for either a full refund, a replacement system or help.

Windows 7 Installation Media Only Boots into Recovery

Ever since I've updated to Windows 8, I have been really pleased. Everything works fine but when I was automatically updated to windows 8.1, I wasn't happy. I mostly use my PC for gaming and emulating my favourite classic game consoles. But windows 8.1 either
doesn't allow games to play, and makes my emulators run at 15 FPS (normally they run at 55-60). And now, I cant install Graphics drivers! I used to be able to on windows 8. 8.1 will not let me run any of my old Windows 7 Apps either,
So, after spending hours backing up my date, ready to start a fresh windows 7 installation, I figured out that I cannot upgrade, or even start the installation from the USB drive!
I had lots of issues with Windows Vista and used the same installation media to fix the OS. Now, the installation ONLY boots into recovery mode!
Luckily, I use Debian KDE on the side, So I am able to use my computer, but not play any games.
Is there any way to have the installation media boot into Win7 Setup?

Hi,
Could you provide with a screen shoot?
Please test the USB drive in another pc.
If it is the same issue, it would be caused by the USB drive.
And then follow the steps to create a bootable USB drive.
Create a Bootable USB Flash Drive
http://technet.microsoft.com/en-us/library/jj200124.aspx
Hope this helps,
Ada Liu
TechNet Community Support

OS X Lion 10.8.2 won't boot into recovery mode

Help! OS X Lion 10.8.2 won't boot into recovery mode, I get a grey screen, the apple icon and the spinning symbol...Does anyone have any suggestions?
Have a MacBook Pro (2009) and had no problems until upgrading to LIon from Snow Leopard... thanks!

Hi there - thanks very much for your suggestion, it did reboot eventually but took a long time to get there.
I've have run Disk Utility. After Verifying the disk it said it needed Repairing - so tried doing that and got the message " Error: Utility can't repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files" I have got Time Machine but haven't backed-up since Dec 12...Can I use "Restore" to copy the MBP HD to an external HD and then re-install Lion?

How do I boot into recovery mode with wireless keyboard

I am unable to boot into recovery mode using either cmd-R or holding down the alt key. How is it supposed to work?
Message was edited by: Niklas Brunberg (better title)

I understand your concerns - I'm glad both of my machines are dual bootable (just in case) and I have my Snow Leopard install disks..... However, this is what Apple has decided, so we need to find the best way to deal with it. Personally, I've tested the recovery mode several times and, at least on my machine, it was not reliable (i.e. it wouldn't work - I tried it again and it did, but it spent more than an hour downloading the entire 4 GB installer again and then another 30 minutes installing it), and on a third try, I found that it had vanished because I had cloned by drive. When you clone, only your system is cloned, not the extra partition.
So, I've decided to rely on a) my bootable clones and b) a copy of the installer (.dmg) in case my clones fail. I don't feel comfortable relying on something that requires an internet connection and a full download to work. But, that works for me; you may want to take a different approach.

2011 MBP only boots in safe mode after yosemite update

After attempting to update to yosemite, 2011 MBP (16GB Ram, 1TB HD) will only boot into safe mode. If I reboot without holding the shift key, I get the Apple logo and progress bar ......... that never goes away, just hangs about half way through. Any help?
Dan

Hey there Danielrbjo,
It sounds like you are unable to boot your mac without using Safe Boot. I would use the other troubleshooting from the following article, named:
Mac OS X: Gray screen appears during startup
Disconnect, test peripheral devices and network cables
Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
Disconnect any Ethernet cables.
Start up your Mac.
If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
Reset the NVRAM / PRAM
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Reset the NVRAM / PRAM.
If the gray screen issue persists, go to the next section.
Remove third-party RAM and internal hardware
Remove any non-Apple RAM or other third-party hardware upgrades (such as expansion cards or third-party optical drives or hard drives, if present) to help isolate the issue. This is necessary to get as close as possible to the original factory hardware configuration of your Mac.
If you are not sure which RAM modules or other hardware is Apple or third-party, or if you are not comfortable performing these steps, or if you have a Mac mini, consider contacting an Apple Authorized Service Provider for assistance. Otherwise, perform these steps before going to the next section.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Open your Mac to access the memory slots. Refer to the User Guide that came with your Mac, or search Apple Support Manuals for a PDF copy of your Mac's User Guide.
Remove any third-party RAM that has been installed.
Reinstall the Apple RAM that came with the computer if available. Note that Mac OS X 10.5 requires 512 MB or more of RAM; Mac OS X 10.4 requires 256 MB or more of RAM.
If your Mac starts up with only Apple RAM installed, contact the vendor of your third-party RAM.
If you have installed a third-party drive, ensure it is running the latest firmware. Otherwise, reinstall the Apple drive that came with the computer if available.
Thank you for using Apple Support Communities.
All the best,
Sterling

HT1414 My ipad has gone into recovery mode after an "error occured" whilst trying to update it. Will it come out of recovery on its own? There is a lot of data I want to save

My ipad has gone into recovery mode after an "error occured" whilst trying to update it. Will it come out of recovery on it's own? There is a lot of data I want to save before restoring it to factory settings

FORCE IPAD INTO RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.

Mac keeps booting into Recovery mode

HI,
my macbook pro mid 2009 keeps booting into recovery mode,
if I select primary disk in recovery mode or at boot holding shift it quickly showes crossed out circle instead of an apple at boot screen than boots into recovery mode again.
I have repair permessions, repaired disk (no errors) and reset pram but no luck.
Is there anything alse I can try?
Thank you.

Looks like some files might be damaged. You will likely have to reinstall the operating system. I hope you have a back up of your data.

Intel Mini will only boot into safe mode - hangs on ANY Mac OS volume

I have an Intel Mac Mini... the core2duo 1.83GHz or whatever.
I acquired it from it's previous owner, as it was "broken".
He could not get it to run an install disc.
It will not boot any of the Mac OS install media (DVD or CD - 10.4, 10.5, 10.6).
It will not boot/install a Linux disc (I haven't tried, but that's what I was told).
It WILL boot/install Windows !?!?
So... anyway, I removed the HDD, and installed OS 10.6 Leopard on it (FW Target mode installs kept failing at the end - regular retail DVD). I then reinstalled the HDD back into the machine.
The system keeps hanging at the same point it would when trying to boot an install DVD - after the screen turns blue, it goes back to the gray screen, then immediately freezes.
However, I eventually discovered that it WILL boot into safe mode !
Everyone kept saying it's the logic board failure, but if it boots into safe mode, can that be true ? It doesn't seem to me that it would be hardware based in that case - unless it's just a specific component, like the Airport module or something.
The last line displayed in Verbose mode when it hangs is:
"athset_txchainmask[5124] sc->sc.config.txchainmask 5 mask 5"
It also says something about the Airport just before that.
I tried removing the Airport module and it still hangs.
I also tried different RAM, with the same results.
I ran the 10.6.2 combo update in Safe Mode. It still hangs. Haven't tried 10.6.3 yet, though I do have it downloaded and ready to install.
This thing is driving me crazy. Please tell me there's a fix, OTHER than replacing the logic board ?!?! It just doesn't seem like it should be so complicated considering that it runs in safe mode.
It's rare I can't figure out a Mac problem - please help !
Message was edited by: maxtechsystems

Very strange, and getting stranger !
Ok... so, from safe boot mode, I installed Windows XP Pro using the boot camp assistant.
Everything installed perfectly. I started up from Windows, and put in the Mac Mini recovery disc, in order to load the drivers. The Boot Camp software started with Auto Run, and I clicked through to install everything. The drivers start loading...Windows reacts positively, with the system tray announcing "new hardware installed" every 30 seconds or so. Airport/WiFi IS working (in Windows), as it detected my router/network...this is where it gets F'ed up - when the installer gets through with the drivers, and installs the boot camp software for Windows - the system reboots, goes through the usual Windows startup...the desktop background appears, but no icons or start menu - then it reboots again...same thing, again, over and over in a loop.
Went back into OS X (safe boot mode). Installed reEFIt (a bootloader utility), to see if maybe I can bypass the Mac OS/Boot Camp bootloader. No luck. Install worked, but still had the same issues.
For the heck of it, I try installing Linux Mint 8. The live CD starts up OK, but only as far as the boot menu. I tried the installer first - after the splash screen, it hangs on a plain gray screen (w/o the normal linux installer language selection menu - just solid grey).
I tried running the live CD w/o the installer - the actual OS. Same thing - after the splash screen, it hangs, only it's a black screen this time. If I use verbose mode, it still seems to hang on the WiFi card.
Here's the strangest thing yet - Ok, remember, it wouldn't boot normally into ANY Mac OS volume - including the installer DVDs - only in safe boot mode...
So, I try the "hackintosh" IPC osX86 10.5.6 DVD - it boots into the installer with NO problem, WITHOUT safe boot mode ! I tried installing it unsuccessfully. I forget now which options I choose, if any, though I may try it again later and pretend it's just a non-apple PC with the same specs as the Mini (or try just the "base system", and the bootloader - then run the official Apple updates)
This last thing really makes me think it has something to do with the EFI/bios - however, I've only been able to find info on how to update it, not replace or restore it - and it's only from a working install, not forced from a flash drive or CD (plus when I do try the installer from safe boot mode, it says it's current and unneeded).
I still haven't changed the hard drive. After almost successfully installing Windows, I made the assumption the -hardware- was OK, and reassembled everything.
Currently, I'm trying a direct installation of Windows XP Pro SP2 with which I'll try installing the drivers WITHOUT the boot camp software, to see if the WiFi (Airport card) and everything else is indeed working OK (remember too that the system passed ALL the ASD 3S116 tests).
So anyway, that's the current status. Any new ideas anyone ?
Thanks.
Message was edited by: maxtechsystems

My Iphone 4s goes into recovery mode after doing the IOS 6 update.

I just tried doing the IOS6 update and after about 2hrs into it my phone goes into recovery mode. The Itunes icon appeared on the phone. When i connected it to Itunes, I tunes said i had to restore and update my phone.
BTW my son did the update in about 15 minutes i tunes says my phone will take 7 HOURS!!!
HELP!!!!

Hi guyz just fixed mine just now, I used an app named iREB please refer to the below link. Make sure youre iphone is plugged in to your USB then launch the app as admin. As soon as the app is running go to the "Recovery Mode Loop Fixer" tab & hit the "Set Auto-Boot True (Fixes 1015 errors / Recovery Loops). It will restart your iPhone in just a moment & get you back to your homescreen.
I hope this will help those whos undergoing this horrifying iPhone problem.
Just additional info.
Issue: Sticked with USB & Itunes Logo during upgrade attempt to iOS 6.0
Iphone 4S (iOS 5.1.1.(9B206)
32 GB
Official Factory Unlock
PC-Win 7 Home Premium 64bit
iREB Download Link:
http://www.yourtechinfo.com/2012/05/how-to-fix-recovery-mode-loop-or-itunes.html #Downloads:
Message was edited by: johnsawan79

Booting into recovery mode and Web service in 10.7 server

I have two servers: Server A is running 10.6 server and server B is running 10.7 server. Both are on the same LAN at a data center. My questions are as follows:
1 - is there a way to restart server B into recovery mode remotely? (and not using a KVM)
2 - if server B was booted successfully into recovery mode is there a way to screen share with it from server A? If so how would this be done?
3 - can Apple Remote Desktop reboot a 10.7 machine into recovery mode and still continue to see its screen?
4 - in the Server app of 10.7 server there is a default website setup in the Web service. it doesn't seem possible to edit any of the information for this default website, is this true?
5 - is there any way to get the Web service in the 10.7 Server Admin tools? it is missing among many other services.
Thanks

Probability is very high that you have a hardware failure. You should get an external bootable drive (or startup with a bootable DVD if you can) JUST to prove that it's not the motherboard, but probably the hard drive that's failed.

Mountain Lion only boots into Recovery mode after using iCould lock

Similar Messages

Maybe you are looking for