Mouse and Keyboard stop working after reboot

So far the computer is working great except for the fact everytime you reboot the keyboard and mouse stop working... I did a clean format x2 and put the service pack on and I am still getting the same problem.
Anyone have this problem or something similair ? Any ideas ?
Thanks in advance :-)

The problem is not your S/W install. It's with the MSI Motherboard. Your best bet is to ask MSI when a fix will be available, or go buy a different board.

Similar Messages

Mouse and Keyboard stops working after a while

Hi, I'm not even sure where to start to find the cause of the problem. I have a normal ps/2 keyboard and USB optical mouse, both of them just stops working after a few hours. The light on the mouse just dies and the keyboard is not responsive at all. I have to do a hard reboot of my computer. How and where can I diagnose the problem? I noticed the problem started when I upgraded to the latest kernel.

And then after a while it will just use a new address:
Oct 31 01:47:15 wdesktop usb 1-1: USB disconnect, address 6
Oct 31 01:47:15 wdesktop usb 1-1: new low speed USB device using uhci_hcd and address 7
Oct 31 01:47:16 wdesktop usb 1-1: configuration #1 chosen from 1 choice
Oct 31 01:47:16 wdesktop input: Microsoft Microsoft Wheel Mouse Optical as /class/input/input8
Oct 31 01:47:16 wdesktop input,hidraw0: USB HID v1.00 Mouse [Microsoft Microsoft Wheel Mouse Optical] on usb-0000:00:10.0-1
Then after that my mouse is unusable, the following is shown:
Oct 31 01:48:41 wdesktop usb 1-1: USB disconnect, address 7
Oct 31 01:48:41 wdesktop usb 1-1: new low speed USB device using uhci_hcd and address 8
Oct 31 01:49:13 wdesktop usb 1-1: new low speed USB device using uhci_hcd and address 9
Oct 31 01:49:45 wdesktop usb 1-1: new low speed USB device using uhci_hcd and address 10
Oct 31 01:49:56 wdesktop usb 1-1: new low speed USB device using uhci_hcd and address 11
Oct 31 01:50:08 wdesktop uhci_hcd 0000:00:10.0: Controller not stopped yet!
Unplugging and plugging the mouse back does not work
I found a workaround for that by unplugging the mouse, removing the uhci_hcd and adding it back, so:
sudo rmmod uhci_hcd
sudo modprobe uhci-hcd
But I'm still not sure what causes the problem.
Last edited by willy (2008-10-30 15:02:54)

Apple wireless mouse and keyboard stop working ... now says OS X version and bluetooth incompatible

For no apparent reason my apple wireless mouse and keyboard stopped working. I was not upgrading or installing anything, the batteries are good, nothing was changed as far as I know. Now bluetooth discovers the paired devices, connects for about 30 seconds, the disconnects ... or stays connected but doesn't work.
What's happenned ... I'm rushing to finish a big job ... any ideas? I've tried re-pairing but doesn't work ... says that OSX version may be incompatible with device bluetooth ... I'm using Lion so maybe there is another lion problem?

Hello:
Barry: What do you mean with "making devices favorites"?
This is the method:
Go to system preferences>bluetooth. Highlight an item in the sidebar. If detailed information does not appear, click on the little gear and select show more info. Then click on the gear again and select favorite.
And how could an hardware-related problem be (temporarily) solved rebooting the OS?
Intermittent problems are, IMHO, most often caused by hardware. Restarting will occasionally "fix" problems - why, I do not know.
Barry

[Solved] Mouse and Keyboard Dont Work After BIOS Update

I spent the last few hours in windows 7 trying to prove to the guys over at MSFN that my problem wasn't driver or bios related by updating to the latest drivers and upgrading my bios to the most recent version. After I was finished I decided to boot back into arch to work some more on my custom kernel (since oddly it had the same problem before the bios update, the mouse and keyboard worked on one boot but once i rebooted into it again they no longer worked) and found that the keyboard and mouse no longer worked, thinking I had rebooted into the custom kernel by accident I rebooted and selected the default kernel once again only to find that the mouse and keyboard still didn't work.
Any ideas on how to fix this? I really don't want to reinstall since I just installed it last night.
Edit: Another silly mistake, i had renamed the original xorg.conf and never put back when I was finished. This makes me wonder why KDM even started up at all though.
Last edited by brando56894 (2010-01-08 08:04:21)

Hello base76, welcome to the HP Forums.
It appears that the mouse and keyboard aren't working correctly. I will try to assist you with this.
To start could you please provide the following:
Model and product numbers for you notebook.
Currently install operating system.
Were these working previously? If yes, were any changes made prior to them not working?
Have you attempted any troubleshooting? If yes, what have you tried so far?
I look forward to your reply.
Thank you for posting on the HP Forums.
I worked on behalf of HP.

Mouse and keyboard stop working ocassionally and I have to re-boot the computer. does anyone else have this issue?

I have a pwoer Mac with a dual quad processor and current os. If I turn off the computer at night and power up the next day my wireless mouse and keyboard do not work nor does my hardwired mouse. I have to hold the power button to re-boot the computer to get it to work.

Open console in Applications>Utilities, check the system log for the date/time of the last problem & the Startup right after that for clues.
And/or...
One way to test is to Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, Test for problem in Safe Mode...
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive
Reboot, test again.
If it only does it in Regular Boot, then it could be some hardware problem like Video card, (Quartz is turned off in Safe Mode), or Airport, or some USB or Firewire device, or 3rd party add-on, Check System Preferences>Accounts>Login Items window to see if it or something relevant is listed.
Check the System Preferences>Other Row, for 3rd party Pref Panes.
Also look in these if they exist, some are invisible...
/private/var/run/StartupItems
/Library/StartupItems
/System/Library/StartupItems
/System/Library/LaunchDaemons
/Library/LaunchDaemons

Mouse and keyboard stop working with Mavericks

This has happened twice now since installing Mavericks.
I'll be working along, and then all of a sudden, I am not able to click with my mouse and my keyboard stops working. I AM able to move the cursor around on the screen. But, I am not able to click on anything and I can't use the keyboard to force quit the finder. The only way to get unstuck is to press the power button on the front of the Mac to shut it down and then restart.
I am using a wired Apple Keyboard and a wireless Apple Magic Mouse. My Mac is a MacPro 2 x 2.3 GHz Quad-Core Intel Xeon Mac.
Like I said. this has never happened before. But it's happened twice since installing Mavericks.

Everytime I restart my computer, especially for updating maverick, my keyboard and attached mouse (both apple for an Imac) stop working. When I plug in an other keyboard, I can get into my Imac again. Would this SMC apply to this problem as well?
What should I do?
thanks, hb

External Mouse and Keyboard Stop Working When X220 is Docked and Screen is Closed

I have an X220 with a docking station, external monitor and external keyboard/mouse. When I start the laptop from a cold boot and it's docked, my external mouse and keyboard work fine with the screen open or closed.
If I undock and redock with the screen closed, the external keyboard doesn't work and the mouse cursor moves, but the mouse buttons don't do anything. If I open the screen, then the keyboard and mouse work fine.
I've swapped the keyboard and mouse and still have the same problem, so it's not the kb/mouse. This is a brand new X220 and the issue has been occurring since it was purchased.
Any thoughts?

hey mhambalek,
hard to say what's going on, though i would recommend heading to http://support.lenovo.com , do a full update of your unit.
also, if the external keyboard & mouse & monitotor is connected to your unit without the docking station, does the same thing happen?
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

T510 Mouse and Keyboard stops working with Windows Update - unable to roll back, happened twice

My mouse has been working fine for a while but it stopped working followed by the keyboard, I put it down to a Windows update but because Windows 7 keeps bluescreening on a restore point I couldn't recover. I contacted Lenovo got the rebuild disc for my machine, completely rebuilt it, all working fine, then after 2 days same issue, mouse stopped, keyboard stopped, restore points make no difference. Does anyone know what windows update is causing this and if there is a fix aside from rebuilding, I can't keep doing this and I need to understand the cause really, not had it with a laptop before. Gone back to using my old laptop until I can get it sorted. Does anyone have any ideas?

I installed the latest drivers via windows update and got the touchpad back, rebooted, it went again. Netiher the trackpoint or touchpad work. I then thought rather than focus on drivers check the bios. I disabled the trackpoint in the bios, still neither works, however if I disable the touchpad in the bios and enable the trackpoint, the trackpoint does consistently work. I can't explain why the touchpad worked after a touchpad update but now fails, the ultranav driver is installed but if both are enabled in the bios it say it isn't installed, if the trackpoint is enabled it tells me I need to enable both so it clearly knows it's there. What's curious is that this doesn't happen on the complete clean IBM build. I can't not turn off windows updates, I'm a developer so Ioad the laptops up with a vast variety of software and I need many of the windows update fixes, either way I am surprised they are conflicting with the touchpad so dramatically. I can't see it being a virus I'm using two layers of protection and if I blow the machine away and installed the updates via an .iso image (so it's never connected to anything else), I can replicate the problem. It's feasible it's another piece of software causing the conflict. Any one have any idea what could be going on or seen it before?

Mouse and keybord stopped working after upgrading to Mavericks.

Since upgrading from snow Leopard to Mavericks, the Apple USB keyboard and mouse nolonger work on my Mac Pro. I've tried booting in safe mode sucsessfuly, but the keyboard and mouse still don't work. Can anybody help me please?
Thanks,
Dave

Test the devices with another computer, if possible. If they work, or if you can't test, see below.
If you don't already have a current backup, back up all data, then reinstall the OS.* You don't need to erase the startup volume, and you won't need the backup unless something goes wrong. If the system was upgraded from an older version of OS X, you may need the Apple ID and password you used.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
If you installed the Java runtime distributed by Apple and still need it, you'll have to reinstall it. The same goes for Xcode.
*The linked support article refers to OS X 10.9 ("Mavericks"), but the procedure is the same for OS X 10.7 ("Lion") and later.

Mouse and Keyboard stop working since Upgrade to Leopard

I upgraded to Leopard on Friday. Twice today, I've had problems with the mouse/keyboard freezing me out of my MBP. I never had this issue prior to upgrading. The first time today, both the KB and mouse quit. Later in the day, just the KB. Both times were after periods of inactivity. I don't remember the exact scenario leading up to it, but in both cases, a reboot fixed it. I don't have enough detail to (in my mind) justify a trip to the genius bar, but maybe someone else out there has seen this and solved the mystery?
Cheers...

FYI, uninstalling Parallels and VMWare's Fusion (I was using both) doesn't help.
However another scrub of the System log did reveal something peculiar. Sort of a mess to post but in case anyone from Apple is watching this, I am attaching. This is coming up right after I resume wake from suspend.
Oct 31 09:33:25 jwilcox-mbp kernel[0]: AppleYukon2: 00000000,00000000 sk98osx_dnet - recovering from missed interrupt
Oct 31 09:33:28 jwilcox-mbp kernel[0]: AppleUSBHub::setPowerState(0x3ef9a00, 2 -> 4) timed out after 10724 ms
Oct 31 09:33:28 jwilcox-mbp kernel[0]: USBF: 124.693 ControlTransaction: control packet 1 error 0xe0004057
Oct 31 09:33:31 jwilcox-mbp kernel[0]: USBF: 127.693 AppleUSBUHCI[0x3dca000]::DeviceRequest - dmaCommand (0x3f27900) already had memory descriptor (0x557e400) - clearing
Oct 31 09:33:31 jwilcox-mbp kernel[0]: USBF: 127.694 AppleUSBUHCI[0x3dca000]::DeviceRequest - buffer dmaCommand (0x3f27800) already had memory descriptor (0x3f51580) - clearing
Oct 31 09:33:31 jwilcox-mbp kernel[0]: USBF: 127.694 ControlTransaction: control packet 1 error 0xe0004057
Oct 31 09:33:32 jwilcox-mbp kernel[0]: AppleYukon2: 00000000,00000000 sk98osx_dnet - recovering from missed interrupt
Oct 31 09:33:46 jwilcox-mbp login[228]: USER_PROCESS: 228 ttys000
Oct 31 09:33:48 jwilcox-mbp kernel[0]: USBF: 144.696 AppleUSBUHCI[0x3dca000]::DeviceRequest - dmaCommand (0x3f27800) already had memory descriptor (0x5467280) - clearing
Oct 31 09:33:48 jwilcox-mbp kernel[0]: USBF: 144.696 AppleUSBUHCI[0x3dca000]::DeviceRequest - buffer dmaCommand (0x3f27900) already had memory descriptor (0x5469780) - clearing
Oct 31 09:33:48 jwilcox-mbp kernel[0]: USBF: 144.696 ControlTransaction: control packet 1 error 0xe0004057
Oct 31 09:33:48 jwilcox-mbp kernel[0]: USBF: 144.696 AppleUSBUHCI[0x3dca000]::DeviceRequest - dmaCommand (0x3f27900) already had memory descriptor (0x601fc00) - clearing
Oct 31 09:33:48 jwilcox-mbp kernel[0]: USBF: 144.696 AppleUSBUHCI[0x3dca000]::DeviceRequest - buffer dmaCommand (0x3f27800) already had memory descriptor (0x601b680) - clearing
Oct 31 09:33:48 jwilcox-mbp kernel[0]: USBF: 144.696 ControlTransaction: control packet 1 error 0xe0004057
Oct 31 09:33:49 jwilcox-mbp kernel[0]: USBF: 144.798 AppleUSBHub[0x3f4b800]::SuspendPort - expected port to be suspended for conversion, but it is not!!

Bluetooth Mighty Mouse and Keyboard not working in Win XP!

Hi All,
I simply cannot get my Bluetooth Mighty Mouse and Keyboard to work in Win XP via Bootcamp! The bluetooth icon appears in the tray and even shows that they are connected but they do nothing at all. One thing to note is that they show up as connected but with no password. Could this be the problem? If I reconnected the two with new passcodes for XP, would they still work when I reboot in OSX?

upgrading to vista sorted things out!

Add-ons for android Firefox stop working after reboot

I have Firefox (ver. 21.0) installed on my Ramos W30 tablet running ICS (4.0.4) and my UG007 android stick running JB (4.1.1). They both have the same problem. After a reboot, the add-ons stop working. If you look at the add-ons, all the info which would show below "options" is gone. The only way I've been able to get them working again is to uninstall and reinstall the add-ons.
Any other way to fix this or prevent this from happening?

I only use 2 add-ons and it happens with both. I use adblock and tabstothefront. They both stop working after reboot.

Safari and firefox stop working after a few minutes of browsing, regardless of what site I'm on. I have to restart my computer to get internet access again but it only works for a few more minutes, then I have to restart again. Please help!

Safari and firefox stop working after a few minutes of browsing, regardless of what site I'm on. I have to restart my computer to get internet access again but it only works for a few more minutes, then I have to restart again. I don't get a spinning ball, it just stops working at whatever page it's on. I can close the program just fine but when I re-open it, either safari or firefox, it freezes trying to load the hompage. This started a few days ago after trying to stream a movie on my computer. I'm on a Mac Air OS X Version 10.6.8 and have downloaded all updates. When I go into finder, it says I have over 80 gigs available. Is there some other memory cache that I need to check? Thanks so much for your help.

ejwoodall wrote:
It's not a router problem as I explained in my post. If it was a router problem then I wouldn't have the problem everywhere I go. It is an issue with the software.
Then I guess the millions of people running 10.5.7 with no issues are just hallucinating that their machines are working fine?
I'm not trying to belittle your issues; you're certainly having them and I know first hand how annoying an intermittent AirPort issue can be. (In fact, mine was due to an AirPort driver bug that no one else seemed to suffer from.)
The single best diagnostic you could do is take your system running 10.5.7 to an Apple Store, and try using their in-store network.
If your machine performs flawlessly, it may be a router issue.
If your machine has connectivity issues there, it may be a hardware problem with your machine.
There have been numerous people in multiple threads over the years who swore that an update was buggy because things used to work, but returned later to sheepishly admit that they took their machine in, a problem was found and fixed, and now their Mac works flawlessly with the newer software.
But simply reinstalling 10.5.5 in no way means the explanation of how firmware bugs may be at play here is incorrect.
In the context of that explanation, all you've done is possibly reinstall software that asks to add "2 + 3."

[solved] mouse and keyboard not working (and previous fix wont work)

i made a clean default setup with
arch
latest kernel - 2.6.29 i think
xorg 1.6.1
video-intel-legacy
on a 865G intel box + tried usb and ps2 keyboards + usb mouse
when i start X the mouse and keyboard dont work (and i have to hard reset the box) in all of the setups i tried. the AutoAddDevices fix suggested before does not work this time
- without xorg.conf
- with auto-generated xorg.conf (X -confogure)
- with the automatic conf +
Section "ServerFlags"
Option "AutoAddDevices" "False"
EndSection
- with tiny xorg.conf containing only
Section "ServerFlags"
Option "AutoAddDevices" "False"
EndSection
- with dbus/hal enabled and disabled in rc.conf
how i make it work
Last edited by ash (2009-04-30 19:01:41)

the setup that works to me now is
automatic xorg.conf with the AutAddDevices False (disable hotplug) lines
dbus and hal enabled in deamons
this lines instruct xorg to use xf86-input-mouse/keyboard instead of evdev. ie it looks like with evdev there is no point in xf86-input-mouse/keyboard
Last edited by ash (2009-04-30 18:26:16)

Windows 7 professional backup and restore stop working after installation of acronis true image 2010

HI,
windows 7 professional backup and restore stop working after installation of acronis true image 2010. it generates a error code 0x81000019. please help.
thanks
Song

Sankalp,
I too have the error 0x81000033 when running the full system image backup. I could not assign a drive letter to my 100mb drive with the Disk Management. So, I went into the diskpart and ran the following commands:
diskpart
list disk
DISKPART> list par
Partition ### Type              Size     Offset
Partition 1    System             100 MB 1024 KB           ( 78.2 of 96.0MB free )
Partition 2    Reserved           128 MB   101 MB
Partition 3    Primary             73 GB   229 MB
Partition 4    Recovery           423 MB    74 GB
sel dis 0
list par
select partition 1
assign letter=q
fsutil usn queryjournal q:
fsutil usn deletejournal /D q:
After diskpart, I opened the "My Computer" and see that I have 78.2 of 96.0MB free. Despite that, I ran these commands on the new q: drive:
C:\Windows\System32>q:
Q:\>fsutil usn queryjournal q:
Error: The parameter is incorrect.
The FSUTIL utility requires a local NTFS volume.
Q:\>fsutil usn deletejournal /D q:
Error: The parameter is incorrect.
The FSUTIL utility requires a local NTFS volume.
Q:\>
Any help is appreciated.

Mouse and Keyboard stop working after reboot

Similar Messages

Maybe you are looking for