Mouse Pad is not working properly while plugged in of Probook 4530s Notebook????

1. Product Name and Number
HP Probook 4530s (Intel Core i5). RAM 6 GB, Hard 750 Gb, Radeon 1 GB card,
Mouse PAD configs ............Synaptics luxpad v7.5,,,,,,,,and........Synaptics luxpad buttons v7.5
Operating System installed:
Windows 7 64 bit Proffessional.
Everytime I plug in the charger, the mouspad starts hanging................What is that........???? Sometimes it stops working at all..............One thing to note is that right and left click buttons are working fine.........
Any suggestions......???

By hanging do you mean it just gets very slow to respond? This only happens when you plug in the charger? I would make sure all your drivers are up to date. Do this happen when the computer is running off battery?
Thanks
Sean
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Similar Messages

Help! My Mouse pad is not working properly. The arrow cannot be controlled, it just keeps jumping all over the page. How can I stop this?

Help! My Mouse pad is not working properly. The arrow cannot be controlled, it just keeps jumping all over the page. How can I stop this?

There are several possible causes for this issue. Please take each of the following steps that you haven't already tried until it's resolved. Some may not apply in your case.
1. Follow the instructions in this support article, and also this one, if applicable. A damaged or defective AC adapter could be the cause, even if it's the right kind.
2. Press down all four corners of the trackpad at once and release. If there's any effect, it's likely to be temporary, and in that case the unit must be serviced or replaced.
3. Open the Bluetooth preference pane in System Preferences and delete all pointing devices other than the trackpad, if applicable. Disconnect any USB pointing devices. By a "pointing device," I mean a peripheral that moves the cursor, such as a trackpad, mouse, trackball, or graphics tablet. A plain keyboard is not a pointing device.
4. Start up in safe mode and test, preferably without launching any third-party applications. If you don't have the problem in safe mode, but it comes back when you restart as usual, stop here and post your results. Do the same if you can't start in safe mode. If there was no difference in safe mode, go on to the next step.
5. Reset the System Management Controller.
6. If you're using a Bluetooth trackpad, investigate potential sources of interference, including USB 3 devices.
7. A swollen battery in a portable computer can impinge on the trackpad from below and cause erratic behavior. If you have trouble clicking the trackpad, this is likely the reason. The battery must be replaced without delay.
8. There's a report that a (possibly defective) Thunderbolt Ethernet adapter can cause the built-in trackpad of a MacBook to behave erratically. If you're using such an adapter, disconnect it and test.
9. There's also a report of erratic cursor movements caused by an external display that was connected but not turned on.
10. If none of the above applies, or if you have another reason to think that your computer is being remotely controlled, remove it from the network by turning off Wi-Fi (or your Wi-Fi access point), disconnecting from a Bluetooth network link, and unplugging the Ethernet cable or USB modem, whichever is applicable. If the cursor movements stop at once, you should suspect an intrusion.
11. Make a "Genius" appointment at an Apple Store to have the machine and/or external trackpad tested.

I am facing problem in playing yahoo pool in Firefox 4 while it was working fine in Firefox 3.6. In Firefox 4 the combination of mouse keys are not working properly.

I am facing problem in playing yahoo pool in Firefox 4 while it was working fine in Firefox 3.6. In Firefox 4 the combination of mouse keys are not working properly.

I updated to Firefox 4.01 today and the middle scroll button on my Lenovo T400 stopped working. I downloaded the updated Ultranav utility and the Ultranav driver for my T400 from here http://www-307.ibm.com/pc/support/site.wss/MIGR-72858.html and then uninstalled the "Thinkpad Ultranav Driver" from Add/Remove programs rebooted and then installed the updated utility and driver (another reboot) and it now works perfectly.
So glad to get this working again.

Pick activity is not working properly while creating two or more file adapt

Hi,
pick activity is not working properly while creating two or more file adapter for bpel process.
bpel process compiled and deployed succesfully but while observing the wsdl file of deployed process you can find only one file adapter. so it polls only from that location.
can anybody help on over this? or it's limitation of jdev to use only one file adapter at time while using Pick.
Thanks
sagar

Does anybody tried this?
Thanks
sagar

My mouse pad is not working

My mouse pad is not working on my hp pavilion g6. The orange light that is usually on is not working and I've tried everything I can think of! I've already double tapped the small circle at the top left corner on the pad. It simply will not work. If anyone has any ideas please let me know.
Thanks

Hi,
Can you post back with the following details.
1. The full Model No. and Product No. of your notebook - see Here for a guide on locating this information.
2. The full version of the operating system you are using ( ie Windows 7 64bit ).
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

G70-250US notebook synaptics mouse pad will not work & keyboard will only work until I log onto pc

I have a G70-250US model notebook with Vista 32. I decided to reload OS due to issues with mouse pad and keyboard. I still have the same problem whereby the mouse pad will not work and keyboard will only work until I log in and then it will not work. External mouse and keyboard will work fine. I tried uninistalling drivers for both and rebooting and letting OS find new hardware and install the drivers and this still did not correct. I even pulled down the synaptics driver from HP site and still not working. I checked the BIOS and it is the most recent. I am at a loss. Any ideas on these issues.

Ok I tested a bunch of different Firefoxes on my pos linux box.
'''''Worked with xmodmap:'''''
Vanilla 16.0.2,
Vanilla 16.0B6,
Ubuntu Firefox 16.0.2 (16.0.2+build1-0ubuntu0.10.04.1)
'''''Did Not Work with xmodmap:'''''
Vanilla 17.0.1,
Ubuntu Firefox 17.0.1 (17.0+build2-0ubuntu0.10.04.1)
I have an old Dell Dimension 2400 I plan to use as a replacement for the Sony Vaio when it pops. I've held out as long as possible because it lacks a pci or usb wifi and I really didn't want to run 50 feet of cat5 up a flight of stairs to it. [as i type this i think i remember where a linksys stick for it might be]. Yes I guess it's about time I just do that.
Don't laugh but the reason I held off adding a simple usb keyboard was just lack of space in my tiny bedroom. My setup is on two tray tables side-by-side. Sony Vaio is on left one, my lcd monitor and mouse are on the other. I barely have room to put a cup of coffee on the one with monitor and mouse let alone a full size usb keyboard lol.
Anyway thank you again for all your help.

I have the macBookPro and the problem is the mouse pad does not work I tried everything but still does not work what should i do ?

I have the macBookPro and the problem is the mouse pad does not work I tried everything but still does not work what should i do ?
so i'm using the usb mouse

I want to clarify the issue.
The issue is with the MBP trackpad, and it works fine with an attached USB mouse.
With some ingenuity, you might be able to fix this yourself, but I suggest visiting your local Apple Store/Genius Bar. Some have fixed this issue and have posted their results online, but the Apple Store should be your first destination.
Post here with your results!!

Hi, recently i bought macbook pro with retina display and installed windows 8 professional original software also. but in windows 8 track pad is not working properly. can you help me with providing drivers for trackpad to work on windows 8 professional .

hi, recently i bought macbook pro with retina display and installed windows 8 professional original software also. but in windows 8 track pad/ TOUCHPAD is not working properly. can you help me with providing drivers for trackpad to work on windows 8 professional .

Did you download and install the Windows Support software? If you did, did you use the Boot Camp Control icon to set up the trackpad how you want it?
http://www.apple.com/support/bootcamp/
https://discussions.apple.com/community/windows_software/boot_camp

Keyboard and mouse pad do not work; authorised service?

the keyboard and mouse pad on my new macbook (3 weeks old)have stopped responding. I have tried everything to restore it except reinstalling the operating system. The disk utility and hardware test do not show any problems, and when I attach an external mouse and keyboard the computer works just fine. Can this problem be anything other than a faulty connection or lose wire?
I live in Venezuela and will have major problems getting the mac back to the US (where it was purchased) for service. Apparently there are "authorised service providers" here in caracas; does that mean they can work on my mac without me losing the warranty?
thanks for any help..

Huh...I've never managed to do what you have, so I'm a bit out of ideas...
That being said, if a customer brought me a machine in that condition, I'd boot from a "live" Linux CD, save all important data on an external drive, wipe the HD clean and install a fresh OS.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Mouse scroll wheel not working properly in ff5

Since upgrading to FF5 the scroll wheel on my mouse doesn't work properly in Firefox - it's works as normal in everything else, just not in Firefox.
When I try scrolling, the wheel clicks (it clicks when turned) 7 or 8 times before the window in FF will scroll, and even then it only scrolls 2 or 3 lines per click. In all prevous versions of FF it would scroll in the same way as it does in all other programs, ie it would scroll 6 lines per wheel click.
It's clearly an issue with FF5 as it only affects FF5 and is annoying enough to make me start using Internet Explorer, which I haven't done for some years.
Anyone else having this problem?

Sorry, this is not possible in the current version of Firefox, but we have an open bug report where we are tracking this issue here:
https://bugzilla.mozilla.org/show_bug.cgi?id=686228
With luck it will be fixed in a future version.

Pavilion dv6 1300 CTO mouse pad will not work... at all

No matter how many different ideas i have tried, the mouse pad on my laptop will NOT work... I really need this fixed...

Can you post the different things you have tried and Current version of OS on this notebook?
Although I am an HP employee, I am speaking for myself and not for HP.
Make it easier for other people to find solutions, by marking my answer with 'Accept as Solution', if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

Automator not working properly while setting comments and moving files to folders, how to proceed?

So, this is my workflow, i've converted it into a folder action and applied it to a folder called "Automator" in my desktop:
i've turned "show this action when the workflow runs" so I can see what is going wrong
here's what I get (each action happens to have a problem to it)
1) Get specified finder items
2/3) Filter / find finder items
those are there just to work for this simple porpouse: identify that i've dropped a pdf file in the "Automator" folder
I move the PDF
The workflows starts
4) Ask for a text
this would be a prompt for me to add a comment to go to the "Spotlight Comment" section when I click on "get info"
put instead I get this...
that's the directiory that the file is in!
so I type some random text that would go to the spotlight comment section
then click OK
5) Set Spotlight Comments for Finder Items
that's the actual action, it should have the text that i've inputted in the last step, but instead it has this:
(Text is the variable that i've setted up to be shown on the ask for text and set spotlight comment...)
so, I have to manually input the comments I want to be on the file
and click continue
6) Label Finder Items
That's the action where i'm suppose to choose the label color, so I do that and click continue
this should work, but the file doesn't change label at all
nothing happens.
7) Move Finder Items
It should move to the "untitled folder", but again, it doesn't.
and that's it.
It's a PDF file, but it's not recognized by the system as a PDF.
When it is recognized, if I move more than one PDF file, the workflow works for just one PDF, instead of working for all of them!
I would reeeeally appreciate any help
the whole point in this was for me not to buy Hazel, but I think I will end up buying it :/
thanks for any help anyone can give me!

hey red_menace, thanks veeeery much for your support, I really appreciate it
as you can notice, i'm new to the automator, i'm actually new to the whole software thing, I have no idea what I'm doing so I really appreciated your help, changed my life and made my day
BUT, it didn't work...
well, it did, partially
I still don't get any comments on the "Spotlight comments" area and when I convert the workflow to a folder action, it does not recognize the file!
here's my workflow:
here's what I did, step by step:
first I added find finder's items, that worked really well, but it labeled all the finders files that were in the folder AND subfolders (the ones that were suppose to already be labeled right)
then I removed the find finder's items and tried, worked well, but I hadn't checked the "ignore the input", so the comments weren't working
so then I ignored the input on the actions that didn't require an iput, so my workflow is the same as yours now… and It's not working.
at first it worked for only 1 pdf, but no comments
then it worked for 50% of the pdfs, with comments
then it stopped working at all.
added the find finders items
worked while testing with one
saved
tried with 7 at the same time
worked… but didn't get any spotlight comments
went back on automator
checked "show this action when the workflow runs" for the spotlight comments action
added the variable as an answer on the "ask for text"
the variable ran as expected, I had the same input I've inputed as an answer for the "ask for text" on the "spotlight comments" action, label went okay and stuff, but i did not get any spotlight comment on the spotlight comment section!!
went back on automator and checked out the "append to existing comments" on "set spotlight comments for finder items"
and still didn't get any comments on the files!
btw, I went back on the automator and removed the find finder items
then tried again with only one file, dropping it in the application. it worked, but I still didn't get any spotlight comments!!
I also tried deleting the ask for text and tried just
but it did not work
I also converted the workflow that working for all expect the comments to a folder action, and it DID NOT recognize the pdf I dropped in the folder, what do I do?!

Re: Satellite L750 - advanced mouse settings are not working properly

Satellite L750 model (One month old). The problem is that every time I start the computer, only works the point device of the mouse synaptics , but retains the advanced settings as pressing with three fingers, turns or you can use the wheel to move up and down the page. The funny thing is that is activated by clicking the mouse icon in the Control Panel. Once I access the icon, the mouse works perfectly and appears in the toolbar.
In Device Management, tells me that works perfectly and that the driver is updated.
Does anyone think of any solution? thanks

Hi
To be honest, I dont really understand what you are talking about.
Do you have problems with the USB mouse or the touchpad?
What device does not work correctly: mouse or touchpad?
The L750 series supports an touchpad with additional feature called Gesture (Multi Touch).
Here you can find nice description on Synaptics page how it works.
http://www.synaptics.com/solutions/technology/touchpad
Furthermore the settings could be found in control panel -> mouse -> Advanced tab
FYI: You can disable and enable the touchpad function pressing the small button above the touchpad surface (On/OFF).

Attachment of type XLS/CSV is not working properly while sending mail

Hi,
I am trying to send mail through the function module SO_NEW_DOCUMENT_ATT_SEND_API1. I am passing data to send a mail with a XLS/CSV file as attachment. I am sending data as ASCII (/Text) mode.
It is working fine in our development system but not in Quality system. In Quality system I am getting the mail with attachment the formatting within the file is messed up. But if I pass TXT instead of CSV it is working fine.
My question is though CSV/XLS/TXT extensions are ASCII formatted still why it's not working for XLS/CSV. Again it's working in Development then why it's not working in Quality.
I have tried the same code in different systems... 4.6C and 4.7 environments also. But it is working only in the development server of 4.7 versions (EBP). It's not working in an environment which is a refresh of the system where it is working fine.
Please let me know anyone who faced similar kind of problem and got any answer.
Thanks,
Achirangshu

Check your conversion rules in both systems to see if they match. On 4.6c Transaction SCOT on your pull down menus Choose Settings-> Conversion rules.
Message was edited by: Vyerah Yende

Scratch pad is not working properly in the Interaction center

Hello All
I am working on CRM 6.00
While receiving a call I opened the scratch pad and wrote some data, then when I went to interaction record import scratch pad, it is not imported
Is there any configuration for the scratch pad ??
Regards
Jacopo Françoise

Hi Jacopo
I do not believe there is any config for Scratch Pad, should work by default.
Check if there are any OSS Notes for your issue.
Regards
Arden

Mouse Pad is not working properly while plugged in of Probook 4530s Notebook????

Similar Messages

Maybe you are looking for