Move Time Capsule and Laptop to New Network

I have been searching the forums it haven't found a clear answer to this question. I have been backing up my laptop using Time Machine and Time Capsule on one wireless network (TC has joined the wireless network, it does not serve as the router for the network). I am now about to move to a new apartment and will be using a new wireless network. Can I transfer the laptop and the Time Machine to the new network and maintain the continuity of the backups I have been making? Can anyone provide guidance on how to do that? Also, is there a way to set it up prior to moving -- I know the SSID and password of the new network. I feel certain that these questions have come up before, but I can't find clear discussion of it.

My suggestion FWIW. Ask the cable/DSL provider if it would be possible to install just a modem with no router. Connect an Ethernet cable from the modem to the World or WAN port on the Time Capsule. Your computer can connect using wireless or wired as you choose.
The above should be done with all devices turned OFF for at least one minute. After you have everything physically connected first turn on the modem and wait until the status lights indicate it is connected to the ISP. Then power up the Time Capsule and wait until the status light turns Green or is blinking orange (or has changed from blinking to steady orange.) Lastly, power up the computer. Open Airport Utility and proceed from there.
If all goes well you will have a functioning network under the control of the Time Capsule router.
If the ISP will not provide a separate modem, then you have some potential problems using your Time Capsule. You would have to configure it to run in Bridge Mode. That means in Airport Utility you have to configure the Wireless setting to use the Join an Existing Network option. I can't tell you if a Time Capsule will work with a third-party router properly, but that is how you have to set it up.

Similar Messages

I want to set up my time capsule on a completely new network & location without losing the old backups. How do I do this?

I want to set up my time capsule on a completely new network & location without losing the old backups. How do I do this? I cannot find anything in the user manual.

The TC is very hard to just move.. it retains too much of the old network setup.. buried deep in the bowels of the firmware configuration files.. or even on the hard disk special partitions used by the TC.. invisible to you btw.. !!
Do a factory reset and setup from scratch.
That factory reset will have no affect on your backups.. even if you rename the TC.. not a bad things since you also want clients to respond to the new network.. simply reset TM to the new TC name and location.
See A4 here.
http://pondini.org/TM/Troubleshooting.html
Factory reset.
The Factory Reset Gen1-4.
Unplug your TC. Hold in reset. and power the TC back on.. without releasing reset for about 10sec. When the status light flashes rapidly; release it.
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Factory reset Gen 5
Hold in reset for about 5sec until the status light flashes quickly.
If your AirPort Time Capsule still doesn’t respond, do a similar reset to the Gen1-4.
Unplug your AirPort Time Capsule .. hold in reset and power the TC back on.. without releasing the reset.. wait until status led flashes rapidly.

Do you have to disable your Wifi on your existing Reuter if using time capsule to Create a new network

Does one need to disable the wifi on ones reuter if using a time capsule to create a new network what happens if you don't and what are the benefits of doing so

No but you may experience a bag of hurt from cross channel interference. You may have to reset the Subset Mask of one of the routers along with separating the broadcast channels.
Further if you then have one device a PC perhaps on one network and your Mac on another you may not be able to share files/ITunes etc.... with any ease.
So switching off the Wifi on the router/modem and hanging an Ethernet cable to the Time Capsule and setting that up as your WiFi router distributing the IP addresses over DHCP really is the least problematical approach.
IF you have cable Internet with a decoder with Ethernet output ditch your old router completely !

How do i take pictures off my time capsule and onto my new mac?

how do i take pictures off my time capsule and onto my new mac?

See Here > http://support.apple.com/kb/HT4083

Time Capsule and External HD as Network Attached Storage

I was wondering if I can
a. Attached and external hard drive to my Time Capsule and access is wirelessly?
b. Back up to that external hard drive using Time Machine?
c. Access that external hard drive and Time Capsule from a remote place off site?
Thanks

a. Yes
b. I think so. But why not just use the TCs hard disk for TM backups?
c. Apparently so based on these instructions I have found: (Haven't tried it myself)
In the Finder preferences check the box "show server" to mount to desktop.
Under Airport Utility:
Disks - check over wan and check file sharing and write down the ip address
Under the Finder, use the GO function to find your server ie the hard drive on the TC. In the window provided type afp://ip address then password if applicable. The hard drive should mount and be shown on the desktop.

Setting up a time capsule without creating a new network.

I want to set up my time machine but without creating a new network. However, my current network doesn't allow to connect a router to the network. When I connect the energy cable to the time capsule it keeps flashing an amber light. When I open the AirPort is says that it didn't find the base stations of AirPort and will keep searching.

To setup a TC.. without creating a new network.. and current network doesn't allow a router to connect.. sorry you have just created a conundrum.. nobody can give you an answer to that. It is impossible to use the TC in that case. It is 100% only a network drive. You should get an external drive and plug it into the computer.
The only solution is to have two networks.. if the current network cannot be used even with a bridged TC.
As long as you have a Mac with both wireless and ethernet you can do it.
See instructions I have with all the screen shots near the bottom of this thread.
https://discussions.apple.com/thread/4817218?tstart=30

Will signal strength or internet speed suffer when using a Generation 1 Time Capsule and wireless extending a network with a Generation 5 Airport Extreme

I have a wireless network in my home and I have a Time Capsule 1st generation and a Airport Extreme 5th Generation, will this cause my internet to be slow or have glitches with signal strength?

We've gone over this in the other thread.
If the Time Capsule will be connecting using wireless only, everything depends on the quality of the connection between the AirPort Extreme and Time Capsule.
The quality of the connection will be affected by the distance that the Time Capsule is located from the AirPort Extreme and any obstructions in the signal path.
If you have a ceiling between the AirPort Extreme and Time Capsule, then you should expect the signal arriving at the Time Capsule to have lost 30-40% of its bandwidth (speed). So, the Time Capsule can only repeat the weaker signal that it receives.
Other walls or other obstructions like heavy furniture, large mirrors, etc will also affect the wireless signal as well as cordless phones and other wireless networks around you.
If you are lucky enough to have line-of-sight between the AirPort Extreme and Time Capsule, then the wireless connection between those devices can work quite well. Few of us have this luxury, and must settle for significant compromises in performance.
If the wireless connection between the AirPort Extreme and Time Capsule does the job for you reliably, then you can leave things as is. If you are not getting the reliable performance that you need, then you will need to establish a wired Ethernet connection between the AirPort Extreme and Time Capsule.
As you might imagine, there is virtually no signal loss in a wire, even up to 300+ feet or 100 meters.

I just purchased two Macbook Air along with two Time Capsule (2TB) for my kids. Meanwhile I use a sagemcom ADLS modem/router for home use. Can I connect both Time Capsule and laptop which will allow both laptop to have their own backup system?

I want both of the computers to have their own independent time capsule.

want both of the computers to have their own independent time capsule.
I assume that you are asking about using the Time Capsules for Time Machine backups here, correct?
If yes, both MBAs will be able to select the specific Time Capsule that they will use for backups, so "point" MBA1 to Time Capsule 1 and MBA2 to Time Capsule 2.
Since you will have plenty of available backup space if you use two Time Capsules, you might want to consider having each MBA back up to both Time Capsule 1 and Time Capsule 2.
This way, if one Time Capsule fails, you will still have a complete set of backups for both MBAs.

Best way to set-up U Verse, Time Capsule and Express to Extend Network

I'm trying to extend my WIFI signal with AP Express and TC using an AT&T U Verse router. Neither the Express nor the TC are directly connected to the U Verse router. Both the Express and the TC show they are connected to the network but when I try and edit the settings to extend the network rather than join the network they both show as not connected any longer. Before on DSL the Express and TC were connected as extending the network (slow but connected). The house is 3 levels U Verse in in the basement. Trying to get a connection on the 3rd floor. We have multiple iPads, iPhones, Mac Book Pro's, an i Mac and Direct TV receivers.
What's the best way to set this up to extend the range of what we have?

You cannot extend range from non-apple routers.
So both the TC and express will join the wireless of the uverse and then become dumb clients..
You need at least one of the two units plugged into the uverse by ethernet.. then the other device can extend that network.
Consider using EOP adapters if your distance is such that even with the correct setup you don't get the range you need. Or better still do it properly and wire it with ethernet.
It is possible to use the Express as a bridge..
So say setup on the first floor.. a wireless bridge from the express to the uverse.. then plug the ethernet into the TC.. and use the TC in bridge mode.. it will not be fast but it can work.
Reset everything to factory and start over.. as you will not be able to get this working without a full reset of the apple routers.
Note still not ideal but it might give you more range than extend wireless with say express plugged into the uverse.

I have working Netgear network. Want to add new Time Capsule and run 2nd network for new apple TV and Imac, and keep the netgear network for my PC and Canon printer.

I have working Netgear N600 dual band router network. The existing network has an XP netbook PC, canon printer, 2 Iphones, Epson Air printer, an Ipad, 3 roku boxes, backup drive. Just bought a new Apple TV box, and time capsule 2T. I have an IMac on order but don't have it here yet.
My goal is to add new Time Capsule and create 2nd "apple" network for new apple TV, Iphones, Ipad, Epson Air printer and new Imac, and keep the netgear network for my PC, Roku TV boxes, and Canon printer and backup drive.
The Netgear router, the time capsule and new IMac will be on the same desktop, I dont need to backup my netbook PC to time capsule.
Where do I start?
Which device connects to my modem first, the TC2 or the Netgear?
Is it best wait for the Imac before starting or can the TC2 be set up from my Ipad or PC?
Thanks.

It is pretty simple..
Setup the TC in bridge and plug it into the Netgear.. I would leave the netgear as the main router for now, although in the future you can swap things around. The netgear firmware may have issues with bonjour and airplay/airprint?? Does your ipad print ok now?
You can setup the TC using Mac, PC (at least up to win7) or iOS.. they all have airport utility available.
Bridge mode is set differently depending on the version of the utility. This is v5 and how the windows one will look (at least similar to).
v6 will be as
With the TC in bridge you will still create a wireless network.. and give it a different name from the netgear.. then all the apple devices can connect to it. Use ethernet rather than wireless if the imac is on the desktop with it. Much faster and better for using Time Machine backups.
If you run into any issues.. just post the particular issue. It will take a bit of getting used to, but isn't hard.

I recently bought a new iMac as well as a wireless time capsule and have it connected how can I use this external drive as the location to store all my files for iTunes, or is this even possible?

New iMac user here, I recently bought a new iMac and Time capsule and have the whole network up and running now. I have connected another external HD to the time capsule as well and have a total of 3 TB of storage connected wireless to my new iMac. My question is can I use this location as the default location for iTunes? I doubt I am gonna run out of room considering the iMac has 1 TB of storage already, but I'd prefer to keep my movies and music off the Mac to keep it running smoothly. If this is possibly, I'd like to do this with iPhoto as well.

I would advise against placing your iTunes library on a Time Capsule.
The Time Capsule is designed as a backup device and not for wireless streaming of video.
Before you do anything more, can I suggest you put into place a reliable, redundant backup strategy.
Unless you are prepared to risk loss of your iTunes library due to a hard drive failure, I would not put iTunes on the Time Capsule.
Leave your iTunes library on your iMac until such time as your internal drive is full. Backup to Time Capsule using Time Machine and create a clone of your internal iMac HD to your external drive.
That's my 2 cents worth. Others may have a different opinion.

Verizon FIOS, Time Capsule, and Airport Express - How to Extend Network

OK, I just got Verizon FIOS (TV, Internet, and phone). Don't care for the wireless router that is required to be used with it (want 802.11n and Time Capsule). I turned of the wireless on the Verizon FIOS router and installed a Time Capsule in Bridge Mode, which is how the Verizon rep told me to install it. As I understand it, the Verizon FIOS router is still handling DHCP, NAT, etc. I would like to extend the wireless network to reach some dead spots in my house. I have read that the Airport Express can be used to extend a wireless network from an Airport Extreme or Time Capsule, but it appears that I need to set up a WDS with the Time Capsule as the base station, which is apparently not possible on the Time Capsule in Bridge Mode. I am desperately seeking any advice on how to use Verizon FIOS, my Time Capsule, and extend the wireless network to reach the farther corners of the house. I am using a Macbook and a Thinkpad as well as an iPhone on the wireless network with a Dell desktop connected to the Time Capsule via Ethernet. Any help or suggestions would be greatly appreciated. Before I switched, I had Cox Cable with a Buffalo wireless router and it had great range. Now I seem to be in a worse situation from a wireless perspective with higher TV and Internet quality. Thanks in advance.

Welcome to the discussions!
+I would like to extend the wireless network to reach some dead spots in my house. I have read that the Airport Express can be used to extend a wireless network from an Airport Extreme or Time Capsule, but it appears that I need to set up a WDS with the Time Capsule as the base station, which is apparently not possible on the Time Capsule in Bridge Mode+
If you have an AirPort Express(n), you can configure it to "extend a wireless network". This is a more efficient way to add additional wireless coverage (and much easier to configure than a WDS arrangement).
However, if you have an older "b/g" AirPort Express, you must use the WDS configuration method with this device and the Time Capsule if you want to increase your wireless coverage.

HT1178 reset my time capsule and connect it directly to imac only for back up

I want to reset my time capsule and start a new complte back up ..How to reset it and use it directly connected to may imac?

Your little comment in the profile.. it used to work before Mavericks.. might be better to fix it and use it still as part of your network. The problem is the TC is a purely network device.. It is not at all easy to use stand alone. You cannot connect directly to it by USB. It really has to be part of the network.
I have used them plugged in by ethernet to a computer that connected to the internet by wireless. That is messy to setup but works. I will need some info to do it.
How does the iMac connect to the network.. and what IP does it get??
From that I can give you setup but with due warning, this may still have network issues as those bugs are in Mavericks. And you could save yourself the effort and just try to get it working as part of the existing network.
OR.. IMHO much better solution in this case. For desktop type computer like iMac.. plug in a USB drive.. Or FW800 or even thunderbolt if you have need for real speed. Thunderbolt>USB3>FW800>USB2. Price wise.. USB3 is now same price as USB2 so that is the best choice if your Mac has USB3 ports. Thunderbolt is still very expensive. FW800 is better than USB2 but is a dead duck.. Nothing you buy will be useful as the port is being phased out.
But even USB2 will work faster, and be more reliable than a TC.
My other suggestion then is to use CCC or SuperDuper and keep Time Machine as a secondary backup for incrementals. You can produce easily a fully bootable backup drive using CCC. Superduper I heard had issues but that might be fixed now. A bootable backup means if you have a disk failure simply boot the computer from the backup. It is hugely superior method. TM can also continue to be used as it works well for incrementals and restoring applications if that becomes necessary.
Just indicate what you want and we can suggest a way forward or give details on the fix with Time Capsule.

Time Capsule and external 2 tb drive

I am trying to connect a 2 tb seagate free agent desk external drive for mac to my time capsule through the USB port. I would like to have additional memory available for the three macs on the home network. Everything works fine for 15 mins or so and then the drive and the time capsule seem to hang. I can no longer see the external dive or connect to the time capsule. I have to restart the time capsule and the drive. (the network stays connected however).
I talked to apple support they tell me that they only support the time capsule not what is connected to it. Seagate says that they only support direct connection to the Mac pc not a network device......any help would be greatly apreciated.

Hi, and welcome to the forums.
Be sure the drive is formatted right (it sounds like it probably is, but double-check it). It's usually best to completely erase and reformat an external, to get rid of the often-problematic software that comes with them.
That drive has it's own power supply, doesn't it? It should work without a powered USB hub, but that's a possibility.
WD's don't have the best reputation here; among other things, some of them have a built-in sleep or "spin down" mode that doesn't always wake or spin back up properly. We see this mostly when they're attached directly, but it's quite possible you're having the same problem.
You might want to try using the drive temporarily while connected directly to your Mac; if the problem persists, then it's something to do with the drive's hardware or firmware.
Also check WD's site for any driver or firmware updates for it.

How can I move (copy) my Time Capsule date to a new 2T hard drive and then wipe the TC and start as a new (clean) Time MACHINE backup?

How can I move (copy) my Time Capsule date to a new 2T hard drive and then wipe the TC and start as a new (clean) Time MACHINE backup?

Just use the archive utility on the disk page of the airport utility manual setup..
If you have lion and v6 airport utility.. it missed out. On lots of things.
Download and install the real.. UTILITY
5.6 http://support.apple.com/kb/DL1482

Move Time Capsule and Laptop to New Network

Similar Messages

Maybe you are looking for